TEST REPORT 1

FCC ID: QEA104124-9T

Test Report

Download: PDF
FCCID_552889

TEST REPORT Report No. : AF012608-001 Date : 2005 June 09 Application No. : LF208001(0) Client : Kid Galaxy Inc. One Sundial Ave, Suite 310 Manchester, NH 03103, U.S.A. Sample Description : One(1) submitted sample stated to be RC Buggies - Caterpillar of Model No. 10412 Rating : 2 x 1.5V AAA size batteries No. of submitted sample : Two (2) piece (s)*** Date Received : 2005 May 13 Test Period : 2005 May 13 – 2005 May 31 Test Requested : FCC Part 15 Certification Test Method : FCC Rules and Regulations Part 15 – July 2004 ANSI C63.4 – 2003 Test Result : See attached sheet(s) from page 2 to 11. Conclusion : The submitted sample was found to comply with requirement of FCC Part 15 Subpart C. For and on behalf of CMA Testing and Certification Laboratories Authorized Signature : Page 1 of 11 Danny Chui EMC Engineer - EL. Division FCC ID : QEA104124-9T This document shall not be reproduced either in full or in part except with written approval by the Authorized Representative of CMA Testing. Room 1302, Yan Hing Centre, 9-13 Wong Chuk Yeung St.., Fo Tan, Shatin, Hong Kong. Tel: (852) 2698 8198 Fax: (852) 2695 4177 E-mail: info@cmatcl.com Web Site: http://www.cmatcl.com

TEST REPORT Report No. : AF012608-001 Date : 2005 June 09 Table of Contents 1 General Information .................................................................................................................................. 3 1.1 General Description ............................................................................................................................ 3 1.2 Location of the test site ....................................................................................................................... 4 1.3 List of measuring equipment............................................................................................................... 5 2 Description of the radiated emission test .................................................................................................. 6 2.1 Test Procedure .................................................................................................................................... 6 2.2 Test Result .......................................................................................................................................... 6 2.3 Radiated Emission Measurement Data ............................................................................................... 7 3 Description of the Line-conducted Test .................................................................................................... 8 3.1 Test Procedure .................................................................................................................................... 8 3.2 Test Result .......................................................................................................................................... 8 3.3 Graph and Table of Conducted Emission Measurement Data ............................................................ 8 4 Photograph ................................................................................................................................................ 9 4.1 Photographs of the Test Setup for Radiated Emission and Conduction Emission.............................. 9 4.2 Photographs of the External and Internal Configurations of the EUT................................................ 9 5 Supplementary document......................................................................................................................... 10 5.1 Bandwidth ......................................................................................................................................... 10 5.2 Duty Cycle ........................................................................................................................................ 10 6 Appendices............................................................................................................................................... 11 Page 2 of 11 FCC ID : QEA104124-9T This document shall not be reproduced either in full or in part except with written approval by the Authorized Representative of CMA Testing. Room 1302, Yan Hing Centre, 9-13 Wong Chuk Yeung St.., Fo Tan, Shatin, Hong Kong. Tel: (852) 2698 8198 Fax: (852) 2695 4177 E-mail: info@cmatcl.com Web Site: http://www.cmatcl.com

TEST REPORT Report No. : AF012608-001 Date : 2005 June 09 1 General Information 1.1 General Description The equipment under test (EUT) is a transmitter for RC Buggies – Caterpillar. Operating at 49.860 MHz which is controlled by a crystal. The EUT is powered by 2 x .15V AAA size battery. Once it turn on, it will transmit a radio signal to the receiver. The brief circuit description is listed as follows : - X1, Q3 and associated circuit act as local oscillator. - Q1 and associated circuit act as RF amplifier. - U1 and associated circuit act as control signal encoder. Page 3 of 11 FCC ID : QEA104124-9T This document shall not be reproduced either in full or in part except with written approval by the Authorized Representative of CMA Testing. Room 1302, Yan Hing Centre, 9-13 Wong Chuk Yeung St.., Fo Tan, Shatin, Hong Kong. Tel: (852) 2698 8198 Fax: (852) 2695 4177 E-mail: info@cmatcl.com Web Site: http://www.cmatcl.com

TEST REPORT Report No. : AF012608-001 Date : 2005 June 09 1.2 Location of the test site Radiated emissions measurements are investigated and taken pursuant to the procedures of ANSI C63.4 – 2003. A Semi-Anechoic Chamber Testing Site is set up for investigation and located at : Ground Floor, Yan Hing Centre, 9 – 13 Wong Chuk Yeung Street, Fo Tan, Shatin, New Territories, Hong Kong. Conducted emissions measurements are investigated and also taken pursuant to the procedures of ANSI C63.4 – 2003. A shielded room is located at : Ground Floor, Yan Hing Centre, 9 – 13 Wong Chuk Yeung Street, Fo Tan, Shatin, New Territories, Hong Kong. Page 4 of 11 FCC ID : QEA104124-9T This document shall not be reproduced either in full or in part except with written approval by the Authorized Representative of CMA Testing. Room 1302, Yan Hing Centre, 9-13 Wong Chuk Yeung St.., Fo Tan, Shatin, Hong Kong. Tel: (852) 2698 8198 Fax: (852) 2695 4177 E-mail: info@cmatcl.com Web Site: http://www.cmatcl.com

TEST REPORT Report No. : AF012608-001 Date : 2005 June 09 1.3 List of measuring equipment Equipment Manufacturer Model No. Serial No. Calibration Certification No. EMI Test Receiver R&S ESCS30 100001 S43284 Broadband Antenna Schaffner CBL6112B 2692 CA3025 Signal Generator IFR 2023B 202302/938 S43098 LISN R&S ESH3-Z5 100038 S43377 LISN R&S ESH3-Z5 100010 S43101 Pulse Limiter R&S ESH3-Z2 100001 S43325 Biconical Antenna R&S HK116 837414/004 2GB05000535-0001 Page 5 of 11 FCC ID : QEA104124-9T This document shall not be reproduced either in full or in part except with written approval by the Authorized Representative of CMA Testing. Room 1302, Yan Hing Centre, 9-13 Wong Chuk Yeung St.., Fo Tan, Shatin, Hong Kong. Tel: (852) 2698 8198 Fax: (852) 2695 4177 E-mail: info@cmatcl.com Web Site: http://www.cmatcl.com

TEST REPORT Report No. : AF012608-001 Date : 2005 June 09 2 Description of the radiated emission test 2.1 Test Procedure Radiated emissions measurements are investigated and taken pursuant to the procedures of ANSI C63.4 – 2003. The equipment under test (EUT) was placed on a non-conductive turntable with dimensions of 1.5m x 1m and 0.8m high above the ground. 3m from the EUT, a broadband antenna mounting on the mast received the signal strength. The turntable was rotated to maximize the emission level. The antenna was then moving along the mast from 1m up to 4m until no more higher value was found. Both horizontal and vertical polarization of the antenna were placed and investigated. The device was rotated through three orthogonal axes to determine which attitude and configuration produce the highest emission during measurement. 2.2 Test Result Peak Detector data was measured unless otherwise stated. * Emissions appearing within the restricted bands shall follow the requirement of section 15.205. It was found that the EUT meet the FCC requirement. Page 6 of 11 FCC ID : QEA104124-9T This document shall not be reproduced either in full or in part except with written approval by the Authorized Representative of CMA Testing. Room 1302, Yan Hing Centre, 9-13 Wong Chuk Yeung St.., Fo Tan, Shatin, Hong Kong. Tel: (852) 2698 8198 Fax: (852) 2695 4177 E-mail: info@cmatcl.com Web Site: http://www.cmatcl.com

TEST REPORT Report No. : AF012608-001 Date : 2005 June 09 2.3 Radiated Emission Measurement Data Radiated emission pursuant to the requirement of FCC Part 15 subpart C Frequency Polarity Reading at Antenna Average Field Limit at 3m Margin (MHz) (H/V) 3m and Cable Factor Strength (dBµV/m) (dB) (dBµV/m) factor (dB) (dB) (dBµV/m) 49.860 V 62.0 10.3 -6.0 66.3 80.0 -13.7 99.720 H 10.9 9.2 - 20.1 43.5 -23.4 149.580 H 9.3 11.9 - 21.2 43.5 -22.3 199.440 H 13.2 9.2 - 22.4 43.5 -21.1 * 249.300 H 13.3 9.7 - 23.0 46.0 -23.0 299.160 H 9.5 13.9 - 23.4 46.0 -22.6 349.020 H 8.2 14.9 - 23.1 46.0 -22.9 398.880 H 9.7 14.9 - 24.6 46.0 -21.4 448.740 H 7.1 17.7 - 24.8 46.0 -21.2 498.600 H 8.0 17.7 - 25.7 46.0 -20.3 Page 7 of 11 FCC ID : QEA104124-9T This document shall not be reproduced either in full or in part except with written approval by the Authorized Representative of CMA Testing. Room 1302, Yan Hing Centre, 9-13 Wong Chuk Yeung St.., Fo Tan, Shatin, Hong Kong. Tel: (852) 2698 8198 Fax: (852) 2695 4177 E-mail: info@cmatcl.com Web Site: http://www.cmatcl.com

TEST REPORT Report No. : AF012608-001 Date : 2005 June 09 3 Description of the Line-conducted Test 3.1 Test Procedure Conducted emissions measurements are investigated and also taken pursuant to the procedures of ANSI C63.4 – 2003. The EUT was setup as described in the procedures, and both lines were measured. 3.2 Test Result No measurement is required as the EUT is a battery-operated product. 3.3 Graph and Table of Conducted Emission Measurement Data Not Applicable Page 8 of 11 FCC ID : QEA104124-9T This document shall not be reproduced either in full or in part except with written approval by the Authorized Representative of CMA Testing. Room 1302, Yan Hing Centre, 9-13 Wong Chuk Yeung St.., Fo Tan, Shatin, Hong Kong. Tel: (852) 2698 8198 Fax: (852) 2695 4177 E-mail: info@cmatcl.com Web Site: http://www.cmatcl.com

TEST REPORT Report No. : AF012608-001 Date : 2005 June 09 4 Photograph 4.1 Photographs of the Test Setup for Radiated Emission and Conduction Emission For electronic filing, the photos are saved with filename TSup1.jpg to TSup2.jpg 4.2 Photographs of the External and Internal Configurations of the EUT For electronic filing, the photos are saved with filename ExPho1.jpg to ExPho2.jpg and InPho1.jpg to InPho2.jpg. Page 9 of 11 FCC ID : QEA104124-9T This document shall not be reproduced either in full or in part except with written approval by the Authorized Representative of CMA Testing. Room 1302, Yan Hing Centre, 9-13 Wong Chuk Yeung St.., Fo Tan, Shatin, Hong Kong. Tel: (852) 2698 8198 Fax: (852) 2695 4177 E-mail: info@cmatcl.com Web Site: http://www.cmatcl.com

TEST REPORT Report No. : AF012608-001 Date : 2005 June 09 5 Supplementary document The following document were submitted by applicant, and for electronic filing, the document are saved with the following filenames: Document Filename ID Label/Location LabelSmp.jpg Block Diagram BlkDia.pdf Schematic Diagram Schem.pdf Users Manual UserMan.pdf Operational Description OpDes.pdf 5.1 Bandwidth The plot on saved in TestRpt 2.pdf shows the fundamental emission is confined in the specified band. The field strength of any emission appearing between the band edges and up to 10 kHz above and below the band edges (49.81 and 49.91 MHz) is at least 26 dB below the carrier level. It meets the requirement of Section 15.235(b). a. Duty Cycle The duty cycle is simply the on-time divided by the period : The duration of one cycle = 1 ms Effective period of the cycle = 0.5 ms x 1 = 0.5 ms Duty Cycle = 0.5 ms / 1 ms = 0.5 Therefore, the average factor is found by 20 log10 0.5 = -6.0 dB Page 10 of 11 FCC ID : QEA104124-9T This document shall not be reproduced either in full or in part except with written approval by the Authorized Representative of CMA Testing. Room 1302, Yan Hing Centre, 9-13 Wong Chuk Yeung St.., Fo Tan, Shatin, Hong Kong. Tel: (852) 2698 8198 Fax: (852) 2695 4177 E-mail: info@cmatcl.com Web Site: http://www.cmatcl.com

TEST REPORT Report No. : AF012608-001 Date : 2005 June 09 6 Appendices A1 Photos of the set-up of Radiated Emissions 1 page A2 Photos of External Configurations 1 page A3 Photos of Internal Configurations 1 page A4 ID Label/Location 1 page A5 Bandwidth Plot 1 page A6 Average Factor 2 pages A7 Block Diagram 1 page A8 Schematics Diagram 1 page A9 User Manual 1 page A10 Operation Description 1 page ***** End of Report ***** Page 11 of 11 FCC ID : QEA104124-9T This document shall not be reproduced either in full or in part except with written approval by the Authorized Representative of CMA Testing. Room 1302, Yan Hing Centre, 9-13 Wong Chuk Yeung St.., Fo Tan, Shatin, Hong Kong. Tel: (852) 2698 8198 Fax: (852) 2695 4177 E-mail: info@cmatcl.com Web Site: http://www.cmatcl.com


Document Created: 2005-06-15 18:06:14
Document Modified: 2005-06-15 18:06:14
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC