Test Report DXX

FCC ID: QEA-T689-24GT

Test Report

Download: PDF
FCCID_2930240

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch No. 1 Workshop, M-10, Middle section, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Report No.: SZEM160100013001 Email: ee.shenzhen@sgs.com Page: 1 of 29 1 Cover page FCC REPORT Application No. : SZEM1601000130CR (SGS SZ No.:T51510270125EM) Applicant: KID GALAXY INC. 2.4G Claw Climber RC tiger, 2.4G Claw Climber RC cheetah, 2.4G Product Name: Claw Climber RC rhino Model No.(EUT): 10300 Add Model No.: 10301, 10302 FCC ID: QEA-T689-24GT Standards: 47 CFR Part 15, Subpart C (2015) Date of Receipt: 2016-01-08 Date of Test: 2016-01-11 to 2016-01-15 Date of Issue: 2016-01-18 Test Result: PASS * . * In the configuration tested, the EUT complied with the standards specified above. Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. ”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160100013001 Page: 2 of 29 2 Version Revision Record Version Chapter Date Modifier Remark 00 2016-01-18 Original Authorized for issue by: Tested By 2016-01-15 (Peter Geng) /Project Engineer Date Prepared By 2016-01-18 (Iris Zhou) /Clerk Date Checked By 2016-01-18 (Eric Fu) /Reviewer Date “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS—CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZENM1s01 00013001 Page 3 of 29 3 Test Summary Tost Item Test Requirement Tost method Result 47 OFR Part15, Subpart G Section lanterna Requirement Anst css 10 (2or3) Pass 1520 Fiekd Strength ofthe. 147 CFR Part 15Subpart C Section Anst css 10 (2or3) Pass Fundamental Signat 15249 (a) 47 OFR Part15, Subpart G Section lGpurious Emissions Anst css 10 (2or3) Pass 15249 (ayis 200 Restricted bands crnp sio. os lround fundamentat |47 Part 15, Subpart Secton frequency EEmission) t (Radiated 1sarscyis 205 Anst css 10 (2o13) C Pass f0dB Occupied 47 OFR Part15, Subpart G Section . Anist Cas 10 (zons) rass BRandwitth 15218 (c) Rematk Model No: 10300, toao1, 1002 Onlythe mode! 10300 was tested, snce the electieal ircult design, leyout, components used and Intenal wiing wereidenticlforall above models. Onl diferent on shape and color "Ti aunent hundby h Conoany tpet o e ereatContin o Sevee mtand evnint malth on uen onccmite e sn meomtein n ces on 10eemene n cocmer achnt i Pems on ContnonttoEncoone Conment m To mtomat t Aducmen i m n Imeaint i. neinfeor and ontin on cedAry ReEIHTR en h mt Bt ncmd c ocComaryatnaige t tw of t rarmrcon any t ntin iit Clenta imietin t ary Te Cmm ie eavly n ho C antdncomendoe t onm paintc Rianactenfemrenrcangalihs ns t stomaie ron e tannntol nsmiedocmnn cavai rpomec onn ut Micit mt witer o on t iGonsary Ay nrane encon otrr o nteata ie conero comaie oi levant Mitmld n eferta ns b oucin o h on nean t i. Urwas oiname e routs marn n ie tut ie y e sandeaivedart neh wnoninuemaces ow coty®

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160100013001 Page: 4 of 29 4 Contents Page 1 COVER PAGE.........................................................................................................................................................1 2 VERSION .................................................................................................................................................................2 3 TEST SUMMARY ...................................................................................................................................................3 4 CONTENTS .............................................................................................................................................................4 5 GENERAL INFORMATION...................................................................................................................................5 5.1 CLIENT INFORMATION ...........................................................................................................................................5 5.2 GENERAL DESCRIPTION OF EUT ............................................................................................................................5 5.3 TEST ENVIRONMENT AND MODE ...........................................................................................................................7 5.4 DESCRIPTION OF SUPPORT UNITS...........................................................................................................................7 5.5 TEST LOCATION .....................................................................................................................................................7 5.6 TEST FACILITY .......................................................................................................................................................8 5.7 DEVIATION FROM STANDARDS ..............................................................................................................................8 5.8 ABNORMALITIES FROM STANDARD CONDITIONS ...................................................................................................8 5.9 OTHER INFORMATION REQUESTED BY THE CUSTOMER .........................................................................................8 5.10 EQUIPMENT LIST ...............................................................................................................................................9 6 TEST RESULTS AND MEASUREMENT DATA..............................................................................................11 6.1 ANTENNA REQUIREMENT ....................................................................................................................................11 6.2 SPURIOUS EMISSIONS...........................................................................................................................................12 6.2.1 Spurious Emissions ................................................................................................................................12 6.3 RESTRICTED BANDS AROUND FUNDAMENTAL FREQUENCY ..................................................................................20 6.4 20DB BANDWIDTH ..............................................................................................................................................26 7 PHOTOGRAPHS ..................................................................................................................................................29 7.1 RADIATED EMISSION TEST SETUP ........................................................................................................................29 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160100013001 Page: 5 of 29 5 General Information 5.1 Client Information Applicant: KID GALAXY INC. Address of Applicant: 150 Dow Street, Tower 2, Unit 425B, Manchester, New Hampshire 03101 U.S.A 5.2 General Description of EUT Product Name: 2.4G Claw Climber RC tiger, 2.4G Claw Climber RC cheetah, 2.4G Claw Climber RC rhino Model No.: 10300 Country of Origin: CHINA Request Age Grading: 5+ Frequency Range: 2405MHz-2468MHz Modulation Type: GFSK Number of Channels: 6 (declared by the client) Channel List: Please refer to the next page Sample Type: Portable production Antenna Type: Integral Antenna Gain: 0dBi Power Supply: 3.0V DC (2 x 1.5V “AAA” Size Battery) “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160100013001 Page: 6 of 29 Operation Frequency each of channel Channel Frequency Channel Frequency Channel Frequency 1CH 2405 MHz N/A N/A 2CH 2415 MHz N/A N/A 3CH 2428 MHz N/A N/A 4CH 2442 MHz N/A N/A 5CH 2458 MHz N/A N/A 6CH 2468 MHz N/A N/A Note: In section 15.31(m), regards to the operating frequency range over 10 MHz, the Lowest frequency, the middle frequency, and the highest frequency of channel were selected to perform the test, and the selected channel see below: Channel Frequency The Lowest channel(CH1) 2405MHz The Middle channel(CH4) 2442MHz The Highest channel(CH6) 2468MHz “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160100013001 Page: 7 of 29 5.3 Test Environment and Mode Operating Environment: Temperature: 25.0 °C Humidity: 50 % RH Atmospheric Pressure: 1015 mbar Test mode: Transmitting mode: Keep the EUT in transmitting mode with modulation. 5.4 Description of Support Units The EUT has been tested independently. 5.5 Test Location All tests were performed at: SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen Branch E&E Lab, No. 1 Workshop, M-10, Middle Section, Science & Technology Park, Shenzhen, Guangdong, China. 518057. Tel: +86 755 2601 2053 Fax: +86 755 2671 0594 No tests were sub-contracted. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160100013001 Page: 8 of 29 5.6 Test Facility The test facility is recognized, certified, or accredited by the following organizations: • CNAS (No. CNAS L2929) CNAS has accredited SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch EMC Lab to ISO/IEC 17025:2005 General Requirements for the Competence of Testing and Calibration Laboratories (CNAS-CL01 Accreditation Criteria for the Competence of Testing and Calibration Laboratories) for the competence in the field of testing. • A2LA (Certificate No. 3816.01) SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory is accredited by the American Association for Laboratory Accreditation(A2LA). Certificate No. 3816.01. • VCCI The 10m Semi-anechoic chamber and Shielded Room of SGS-CSTC Standards Technical Services Co., Ltd. have been registered in accordance with the Regulations for Voluntary Control Measures with Registration No.: G-823, R-4188, T-1153 and C-2383 respectively. • FCC – Registration No.: 556682 SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in our files. Registration No.: 556682. • Industry Canada (IC) The 3m Semi-anechoic chambers and the 10m Semi-anechoic chambers of SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch EMC Lab have been registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 4620C-2, 4620C-3. 5.7 Deviation from Standards None. 5.8 Abnormalities from Standard Conditions None. 5.9 Other Information Requested by the Customer None. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160100013001 Page: 9 of 29 5.10 Equipment List RE in Chamber Inventory Cal. date Cal.Due date Item Test Equipment Manufacturer Model No. No. (yyyy-mm-dd) (yyyy-mm-dd) 3m 1 Semi-Anechoic ETS-LINDGREN N/A SEL0017 2015-05-13 2016-05-13 Chamber Agilent 2 EMI Test Receiver N9038A SEL0312 2015-09-16 2016-09-16 Technologies 3 EMI Test software AUDIX E3 SEL0050 N/A N/A BiConiLog 4 Antenna ETS-LINDGREN 3142C SEL0015 2014-11-15 2017-11-15 (26-3000MHz) Double-ridged 5 horn ETS-LINDGREN 3117 SEL0006 2015-10-17 2016-10-17 (1-18GHz) Horn Antenna 6 ETS-LINDGREN 3160 SEL0076 2014-11-24 2017-11-24 (18-26GHz) Pre-amplifier Agilent 7 8447D SEL0053 2015-05-13 2016-05-13 (0.1-1300MHz) Technologies Compliance Pre-Amplifier 8 Directions PAP-0126 SEL0168 2015-10-17 2016-10-17 (0.1-26.5GHz) Systems Inc. 9 Coaxial cable SGS N/A SEL0027 2015-05-13 2016-05-13 10 Coaxial cable SGS N/A SEL0189 2015-05-13 2016-05-13 11 Coaxial cable SGS N/A SEL0121 2015-05-13 2016-05-13 12 Coaxial cable SGS N/A SEL0178 2015-05-13 2016-05-13 13 Band filter Amindeon 82346 SEL0094 2015-05-13 2016-05-13 14 Barometer Chang Chun DYM3 SEL0088 2015-05-13 2016-05-13 15 DC Power Supply Zhao Xin RXN-305D SEL0117 2015-10-09 2016-10-09 16 Humidity/ Temperature Shanhai Qixiang ZJ1-2B SEL0103 2015-10-24 2016-10-24 Indicator 17 Signal Generator Rohde & Schwarz SMR27 SEL0067 2015-05-13 2016-05-13 (10M-27GHz) 18 Loop Antenna Beijing Daze ZN30401 SEL0203 2015-05-13 2016-05-13 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160100013001 Page: 10 of 29 RF connected test Cal. date Cal.Due Item Test Equipment Manufacturer Model No. Inventory No. (yyyy-mm-dd) date (yyyy-mm-dd) 1 DC Power Supply Zhao Xin RXN-305D SEL0117 2015-10-09 2016-10-09 Humidity/ 2 Temperature HYGRO ZJ1-2B SEL0033 2015-10-24 2016-10-24 Indicator Spectrum Rohde & 3 FSP SEL0154 2015-10-17 2016-10-17 Analyzer Schwarz 4 Coaxial cable SGS N/A SEL0178 2015-05-13 2016-05-13 5 Coaxial cable SGS N/A SEL0179 2015-05-13 2016-05-13 6 Barometer ChangChun DYM3 SEL0088 2015-05-13 2016-05-13 Rohde & 7 Signal Generator SML03 SEL0068 2015-04-25 2016-04-25 Schwarz 8 POWER METER R&S NRVS SEL0144 2015-10-09 2016-10-09 Beijin feihang 9 Attenuator TST-2-6dB SEL0205 2015-04-25 2016-04-25 taida “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160100013001 Page: 11 of 29 6 Test results and Measurement Data 6.1 Antenna Requirement Standard requirement: 47 CFR Part 15C Section 15.203 15.203 requirement: An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator, the manufacturer may design the unit so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited. EUT Antenna: The antenna is integrated on the main PCB and no consideration of replacement. The best case gain of the antenna is 0dBi. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160100013001 Page: 12 of 29 6.2 Spurious Emissions 6.2.1 Spurious Emissions Test Requirement: 47 CFR Part 15C Section 15.249 and 15.209 Test Method: ANSI C63.10: 2013 Test Site: Measurement Distance: 3m Receiver Setup: Frequency Detector RBW VBW Remark 0.009MHz-0.090MHz Peak 10kHz 30KHz Peak 0.009MHz-0.090MHz Average 10kHz 30KHz Average 0.090MHz-0.110MHz Quasi-peak 10kHz 30KHz Quasi-peak 0.110MHz-0.490MHz Peak 10kHz 30KHz Peak 0.110MHz-0.490MHz Average 10kHz 30KHz Average 0.490MHz -30MHz Quasi-peak 10kHz 30kHz Quasi-peak 30MHz-1GHz Quasi-peak 100 kHz 300KHz Quasi-peak Peak 1MHz 3MHz Peak Above 1GHz Peak 1MHz 10Hz Average Limit: Field strength Limit Measurement (Spurious Emissions) Frequency (microvolt/ Remark (dBuV/m ) distance (m) meter) 0.009MHz-0.490MHz 2400/F(kHz) - - 300 0.490MHz-1.705MHz 24000/F(kHz) - - 30 1.705MHz-30MHz 30 - - 30 30MHz-88MHz 100 40.0 Quasi-peak 3 88MHz-216MHz 150 43.5 Quasi-peak 3 216MHz-960MHz 200 46.0 Quasi-peak 3 960MHz-1GHz 500 54.0 Quasi-peak 3 Above 1GHz 500 54.0 Average 3 Note: 15.35(b), Unless otherwise specified, the limit on peak radio frequency emissions is 20dB above the maximum permitted average emission limit applicable to the equipment under test. This peak limit applies to the total peak emission level radiated by the device. Limit: Frequency Limit (dBuV/m @3m) Remark (Field strength of the 94.0 Average Value 2400MHz-2483.5MHz fundamental signal) 114.0 Peak Value Test Setup: “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160100013001 Page: 13 of 29 Figure 1. Below 30MHz Figure 2. 30MHz to 1GHz Figure 3. Above 1 GHz Test Procedure: a. For below 1GHz, the EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter semi-anechoic camber. The table was rotated 360 degrees to determine the position of the highest radiation. b. For above 1GHz, the EUT was placed on the top of a rotating table 1.5 meters above the ground at a 3 meter semi-anechoic camber. The table was rotated 360 degrees to determine the position of the highest radiation c. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. d. The antenna height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. e. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters (for the test frequency of below 30MHz, the antenna was tuned to heights 1 meter) and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. f. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. g. If the emission level of the EUT in peak mode was 10dB lower than the limit specified, then testing could be stopped and the peak values of the EUT would be reported. Otherwise the emissions that did not have 10dB margin would be re-tested one by one using peak, quasi-peak or average method “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160100013001 Page: 14 of 29 as specified and then reported in a data sheet. h. Test the EUT in the lowest channel, the middle channel, the Highest channel i. The radiation measurements are performed in X, Y, Z axis positioning for Transmitting mode, And found the X axis positioning which it is worse case. j. Repeat above procedures until all frequencies measured was complete. Instruments Used: Refer to section 5.10 for details Exploratory Test Mode: Transmitting mode Final Test Mode: Transmitting mode Test Results: Pass “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160100013001 Page: 15 of 29 Measurement Data 6.2.1.1 Field Strength Of The Fundamental Signal Peak value: Cable Antenna Preamp Read Over Frequency Level Limit Line Loss Factor Factor Level Limit Polarization (MHz) (dBuV/m) (dBuV/m) (dB) (dB/m) (dB) (dBuV) (dB) 2405 28.62 5.35 38.11 87.66 83.52 114.00 -30.48 Horizontal 2405 28.62 5.35 38.11 84.53 80.39 114.00 -33.61 Vertical 2442 28.79 5.38 38.11 85.72 81.78 114.00 -32.22 Horizontal 2442 28.79 5.38 38.11 85.09 81.15 114.00 -32.85 Vertical 2468 28.92 5.4 38.12 86.68 82.88 114.00 -31.12 Horizontal 2468 28.92 5.4 38.12 81.34 77.54 114.00 -36.46 Vertical “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160100013001 Page: 16 of 29 6.2.1.2 Spurious Emissions 30MHz~1GHz Test mode: Transmitting QP value: Horizontal: “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160100013001 Page: 17 of 29 Vertical: “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160100013001 Page: 18 of 29 Above 1GHz Test mode: Transmitting Test channel: Lowest Remark: Peak Cable Antenna Preamp Read Over Frequency Level Limit Line Polarizatio Loss Factor Factor Level Limit (MHz) (dBuV/m) (dBuV/m) n (dB) (dB/m) (dB) (dBuV) (dB) 3892.524 32.99 7.77 38.52 44.42 46.66 74 -27.34 Vertical 4810.000 34.11 8.88 38.75 44.87 49.11 74 -24.89 Vertical 6087.002 34.74 10.45 38.85 45.29 51.63 74 -22.37 Vertical 7215.000 35.59 10.68 37.63 40.28 48.92 74 -25.08 Vertical 9620.000 37.10 12.51 36.33 35.87 49.15 74 -24.85 Vertical 12603.270 37.90 14.44 37.75 38.28 52.87 74 -21.13 Vertical 3770.567 32.78 7.73 38.47 45.13 47.17 74 -26.83 Horizontal 4810.000 34.11 8.88 38.75 46.34 50.58 74 -23.42 Horizontal 5982.226 34.66 10.51 38.96 46.24 52.45 74 -21.55 Horizontal 7215.000 35.59 10.68 37.63 40.48 49.12 74 -24.88 Horizontal 9620.000 37.10 12.51 36.33 36.51 49.79 74 -24.21 Horizontal 12639.790 37.92 14.55 37.79 37.51 52.19 74 -21.81 Horizontal Test mode: Transmitting Test channel: Middle Remark: Peak Cable Antenna Preamp Read Over Frequency Level Limit Line Loss Factor Factor Level Limit Polarization (MHz) (dBuV/m) (dBuV/m) (dB) (dB/m) (dB) (dBuV) (dB) 3770.567 32.78 7.73 38.47 44.65 46.69 74 -27.31 Vertical 4884.000 34.18 8.98 38.77 45.74 50.13 74 -23.87 Vertical 6016.949 34.71 10.54 38.94 45.81 52.12 74 -21.88 Vertical 7326.000 35.54 10.73 37.59 42.27 50.95 74 -23.05 Vertical 9768.000 37.10 12.59 36.13 37.44 51.00 74 -23.00 Vertical 12603.270 37.90 14.44 37.75 37.56 52.15 74 -21.85 Vertical 3814.467 32.91 7.75 38.49 44.51 46.68 74 -27.32 Horizontal 4884.000 34.18 8.98 38.77 46.50 50.89 74 -23.11 Horizontal 6087.002 34.74 10.45 38.85 46.21 52.55 74 -21.45 Horizontal 7326.000 35.54 10.73 37.59 43.53 52.21 74 -21.79 Horizontal 9768.000 37.10 12.59 36.13 37.20 50.76 74 -23.24 Horizontal 12603.270 37.90 14.44 37.75 38.85 53.44 74 -20.56 Horizontal “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160100013001 Page: 19 of 29 Test mode: Transmitting Test channel: Highest Remark: Peak Cable Antenna Preamp Read Over Frequency Level Limit Line Loss Factor Factor Level Limit Polarization (MHz) (dBuV/m) (dBuV/m) (dB) (dB/m) (dB) (dBuV) (dB) 3641.878 32.27 7.68 38.42 46.15 47.68 74 -26.32 Vertical 4936.000 34.24 9.05 38.78 45.33 49.84 74 -24.16 Vertical 5964.939 34.61 10.46 38.95 45.78 51.90 74 -22.10 Vertical 7404.000 35.51 10.75 37.55 39.46 48.17 74 -25.83 Vertical 9872.000 37.17 12.64 36.00 38.13 51.94 74 -22.06 Vertical 12603.270 37.90 14.44 37.75 38.70 53.29 74 -20.71 Vertical 3684.279 32.44 7.70 38.44 43.97 45.67 74 -28.33 Horizontal 4936.000 34.24 9.05 38.78 47.54 52.05 74 -21.95 Horizontal 6016.949 34.71 10.54 38.94 45.99 52.30 74 -21.70 Horizontal 7404.000 35.51 10.75 37.55 39.81 48.52 74 -25.48 Horizontal 9872.000 37.17 12.64 36.00 38.60 52.41 74 -21.59 Horizontal 12603.270 37.90 14.44 37.75 36.76 51.35 74 -22.65 Horizontal Remark: 1) The field strength is calculated by adding the Antenna Factor, Cable Factor & Preamplifier. The basic equation with a sample calculation is as follows: Final Test Level =Receiver Reading + Antenna Factor + Cable Factor – Preamplifier Factor 2) Scan from 9kHz to 25GHz,The disturbance above 13GHz and below 30MHz was very low, and the above harmonics were the highest point could be found when testing, so only the above harmonics had been displayed. The amplitude of spurious emissions from the radiator which are attenuated more than 20dB below the limit need not be reported . 3) As shown in this section, for frequencies above 1GHz, the field strength limits are based on average limits. However, the peak field strength of any emission shall not exceed the maximum permitted average limits specified above by more than 20 dB under any condition of modulation. So, only the peak measurements were shown in the report. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160100013001 Page: 20 of 29 6.3 Restricted bands around fundamental frequency Test Requirement: 47 CFR Part 15C Section 15.209 and 15.205 Test Method: ANSI C63.10: 2013 Test site: Measurement Distance: 3m Limit(band edge): Emissions radiated outside of the specified frequency bands, except for harmonics, shall be attenuated by at least 50 dB below the level of the fundamental or to the general radiated emission limits in Section 15.209, whichever is the lesser attenuation. Frequency Limit (dBuV/m @3m) Remark 30MHz-88MHz 40.0 Quasi-peak Value 88MHz-216MHz 43.5 Quasi-peak Value 216MHz-960MHz 46.0 Quasi-peak Value 960MHz-1GHz 54.0 Quasi-peak Value 54.0 Average Value Above 1GHz 74.0 Peak Value Test Setup: Figure 1. 30MHz to 1GHz Figure 2. Above 1 GHz “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160100013001 Page: 21 of 29 Test Procedure: a. For below 1GHz, the EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter semi-anechoic camber. The table was rotated 360 degrees to determine the position of the highest radiation. b. For above 1GHz, the EUT was placed on the top of a rotating table 1.5 meters above the ground at a 3 meter semi-anechoic camber. The table was rotated 360 degrees to determine the position of the highest radiation. c. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. d. The antenna height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. e. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. f. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. g. Place a marker at the end of the restricted band closest to the transmit frequency to show compliance. Also measure any emissions in the restricted bands. Save the spectrum analyzer plot. Repeat for each power and modulation for lowest and highest channel h. Test the EUT in the lowest channel , the Highest channel i. The radiation measurements are performed in X, Y, Z axis positioning for Transmitting mode,And found the X axis positioning which it is worse case.. j. Repeat above procedures until all frequencies measured was complete. Instruments Used: Refer to section 5.10 for details Exploratory Test Mode: Transmitting mode Final Test Mode: Transmitting mode Test Results: Pass “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160100013001 Page: 22 of 29 Band edge (Radiated Emission) Test mode: Transmitting Test channel: Lowest Remark: Peak Horizontal: “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160100013001 Page: 23 of 29 Vertical: “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160100013001 Page: 24 of 29 Test mode: Transmitting Test channel: Highest Remark: Peak Horizontal: “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160100013001 Page: 25 of 29 Vertical: Note: 1)The field strength is calculated by adding the Antenna Factor, Cable Factor & Preamplifier. The basic equation with a sample calculation is as follows: 2)Final Test Level =Receiver Reading + Antenna Factor + Cable Factor – Preamplifier Factor 3)The spurious emissions in the restricted band with Peak detector are below the Average limit, so the tests with Average detector is no need to conduct. It is deemed to comply with the requirement. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160100013001 Page: 26 of 29 6.4 20dB Bandwidth Test Requirement: 47 CFR Part 15C Section 15.215 Test Method: ANSI C63.10:2013 Test Setup: Instruments Used: Refer to section 5.10 for details Test mode: Transmitting mode Limit: Within the band 2400MHz-2483.5MHz Test Results: Pass Measurement Data Test channel 20dB bandwidth (MHz) Results Lowest 1.007 Pass Middle 1.431 Pass Highest 0.989 Pass “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160100013001 Page: 27 of 29 Test plot as follows: Test channel: Lowest Test channel: Middle “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160100013001 Page: 28 of 29 Test channel: Highest “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160100013001 Page: 29 of 29 7 Photographs Test model No.: 10300 7.1 Radiated Emission Test Setup “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”


Document Created: 2016-03-10 05:58:30
Document Modified: 2016-03-10 05:58:30
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC