test report II

FCC ID: Q9SAWR-D6000

Test Report

Download: PDF
FCCID_4316595

® A\G # T H i i Attestatiao:lof Global Compliance Report No.: AGC02294181204FE10 Page 61 of 84 Frequency Response of High Channel———H Power 12.5 KHz Channel Separations 15 Deviation —30 \ I —~40 Note: All the modes had been tested, but only the worst data recorded in the report. The results s‘ & virl fii@sfi" kreport refer only to the sample(s) tested unless otherwise stated and the sample(s) are retained for 30 days only. The document is issued by/A C§€ this docu’f& it cannot be reproduced except in full with our prior written permission. The more details and the authenticity of the report will be confirmed a tfittp://www.agc-«& t.com. o Attestatic /2f Global Co pliance Tel: +86—755 2908 1955 Fax: +86—755 2600 8484 E—mail: agc@age—cert.com @ 400 089 2118 B# Add: 2/F. , Building 2, No.1—4, Chaxi Sanwei Technical Industrial Park,Gushu, Xixiang, Bacan District, Shenzhen, Guangdong China

Report No.: AGC02294181204FE10 Page 62 of 84 10. MAXIMUMN TRANSMITTER POWER (CONDUCTED OUTPUT POWER) PEAK POWER 10.1 PROVISIONS APPLICABLE Per FCC §2.1046 § 22.565 and §90.205: Maximum ERP is dependent upon the station’s antenna HAAT and required service area. 10.2 TEST PROCEDURE The RF output of Two-way Radio was conducted to a spectrum analyzer through an appropriate attenuator. In the semi-anechoic chamber, setup as illustrated above the DUT placed on the 0.8m height of Turn Table, rotated the table 45 degree each interval to search the maximum radiation power and receiver antenna shall be rotated vertical and horizontal polarization and moved height from 1m to 4m to find the maximum polar radiated power for each degree interval. The “Read Value” is the spectrum reading of maximum power value. The substitution antenna is substituted for DUT at the same position and signals generator (S.G) export the CW signal to the substitution antenna via a TX cable. The receiver antenna shall be rotated vertical and horizontal polarization and moved height from 1m to 4m to find the maximum radiation power. Record the power level of maximum radiation power from spectrum. So, the Measured substitution value = Ref level of S.G + TX cables loss – Substituted Antenna Gain. EIRP = “Read Value” + Measured substitution value + 2.15. 10.3 TEST CONFIGURATION Conducted Output Power: Effective Radiated Power Radiated Below1GHz

® A\G 7 HA cgmp"ancg uia, & ol\ Report No.: AGC02294181204FE10 Page 63 of 84 YX < < € < € « \k y Anodermdormoredsnenbmndacad Y y Y y Y & ¥o¥ 2 € Antenna Tower < ~ Antenne * & U ~= [— 80 cm C s k . ®em I — [ —. & Iumntable: /\ yA~jasAgAcAA. A A P# A_. /N —4 signal Generator Test Receiver Antenna Tower ]— (Turtable} Test Receiver | j npate Controiier Antenna Tower (Turntable} * The results ’m i oi @mfi‘eport refer only to the sample(s) tested unless otherwise stated and the sample(s) are retained for 30 days only. The document is issued by h (§€ this docu(f&9 t cannot be reproduced except in full with our prior written permission. The more details and the authenticity of the report will be confirmed tfittp://www.agc% t.com. S §& 9 AttestatiQ fGIoba!Q o pliance Tel: +86—755 2908 1955 Fax: +86—755 2600 8484 E—mail: agc@age—cert.com @ 400 089 2118 Add: 2/F. , Building 2, No.1—4, Chaxi Sanwei Technical Industrial Park,Gushu, Xixiang, Bacan District, Shenzhen, Guangdong China

Report No.: AGC02294181204FE10 Page 64 of 84 10.4 TEST RESULT The maximum Conducted Power (CP) for VHF/UHF is Analog: 2W/0.5 W for 12.5 KHz Channel Separation VHF Analog: 2W/0.5 W for 12.5 KHz Channel Separation UHF Digital: 2W/0.5 W for 12.5 KHz Channel Separation VHF Digital: 2W/0.5 W for 12.5 KHz Channel Separation UHF Calculation Formula: CP = R + A + L Note: CP: The final Conducted Power R : The reading value from spectrum analyzer A : The attenuation value of the used attenuator L : The loss of all connection cables

Report No.: AGC02294181204FE10 Page 65 of 84 UHF: Analog: Conducted Power Measurement Results-2W Measurement Result (dBm) Channel Separation Channel For 33dBm(2W) Bottom(400.025MHz) 32.21 Middle(453.225MHz) 32.35 12.5 KHz Middle(454.025MHz) 32.34 Top (479.975MHz ) 32.46 Radiated Power Measurement Results-2W Measurement Result (dBm) Channel Separation Channel For 33dBm(2W) Bottom(400.025MHz) 32.14 Middle(453.225MHz) 32.27 12.5 KHz Middle(454.025MHz) 32.24 Top (479.975MHz ) 32.31 Conducted Power Measurement Results-0.5W Measurement Result (dBm) Channel Separation Channel For 26.99dBm(0.5W) Bottom(400.025MHz) 26.31 Middle(453.225MHz) 26.35 12.5 KHz Middle(454.025MHz) 26.33 Top (479.975MHz ) 26.47 Radiated Power Measurement Results-0.5W Measurement Result (dBm) Channel Separation Channel For 26.99dBm(0.5W) Bottom(400.025MHz) 26.21 Middle(453.225MHz) 26.24 12.5 KHz Middle(454.025MHz) 26.23 Top (479.975MHz ) 26.35

Report No.: AGC02294181204FE10 Page 66 of 84 Digital: Date + voice: Conducted Power Measurement Results-2W Measurement Result (dBm) Channel Separation Channel For 33dBm(2W) Bottom(400.025MHz) 32.18 Middle(453.225MHz) 32.14 12.5 KHz Middle(454.025MHz) 32.15 Top (479.975MHz ) 32.19 Radiated Power Measurement Results-2W Measurement Result (dBm) Channel Separation Channel For 33dBm(2W) Bottom(400.025MHz) 32.09 Middle(453.225MHz) 32.05 12.5 KHz Middle(454.025MHz) 32.06 Top (479.975MHz ) 32.13 Date transmission mode: Conducted Power Measurement Results-2W Measurement Result (dBm) Channel Separation Channel For 33dBm(2W) Bottom(400.025MHz) 31.99 Middle(453.225MHz) 31.98 12.5 KHz Middle(454.025MHz) 31.96 Top (479.975MHz ) 32.08

Report No.: AGC02294181204FE10 Page 67 of 84 Radiated Power Measurement Results-2W Measurement Result (dBm) Channel Separation Channel For 33dBm(2W) Bottom(400.025MHz) 31.95 Middle(453.225MHz) 31.94 12.5 KHz Middle(454.025MHz) 31.92 Top (479.975MHz ) 32.01 Date + voice: Conducted Power Measurement Results-0.5W Measurement Result (dBm) Channel Separation Channel For 26.99dBm(0.5W) Bottom(400.025MHz) 26.21 Middle(453.225MHz) 26.35 12.5 KHz Middle(454.025MHz) 26.31 Top (479.975MHz ) 26.36 Radiated Power Measurement Results-0.5W Measurement Result (dBm) Channel Separation Channel For 26.99dBm(0.5W) Bottom(400.025MHz) 26.15 Middle(453.225MHz) 26.22 12.5 KHz Middle(454.025MHz) 26.19 Top (479.975MHz ) 26.24

Report No.: AGC02294181204FE10 Page 68 of 84 Date transmission mode: Conducted Power Measurement Results-0.5W Measurement Result (dBm) Channel Separation Channel For 26.99dBm(0.5W) Bottom(400.025MHz) 26.14 Middle(453.225MHz) 26.15 12.5 KHz Middle(454.025MHz) 26.12 Top (479.975MHz ) 26.18 Radiated Power Measurement Results-0.5W Measurement Result (dBm) Channel Separation Channel For 26.99dBm(0.5W) Bottom(400.025MHz) 26.07 Middle(453.225MHz) 26.08 12.5 KHz Middle(454.025MHz) 26.05 Top (479.975MHz ) 26.11

Report No.: AGC02294181204FE10 Page 69 of 84 10.5 CONDUCT SPURIOUS PLOT Note:The EUT antenna is a non-removable antenna and does not need to measure Conduct spurious

® A\G & T I& micg Attestation of Global Compliance Report No.: AGC02294181204FE10 Page 70 of 84 11. RANSMITTER FREQUENCY BEHAVIOR 11.1PROVISIONS APPLICABLE FCC §90.214 All equipment ie i q Maximum frequency Time intervals t difference 150 to 174 MHz 421 to 512 & MHz Transient Frequency Behavior for Equipment Designed to Operate on 25 kHz Channels fp $ Lo nlnl n n nn en n nn en nn nc nennennenemnennnennennen en | + 25.0 KHz 5.0 ms 10.0 ms o eEA ¢A 121 20.0 ms 25.0 ms fg $ uonl ns in n nc nv en nrncrncrnsresrrrerrereerrenmesrnsenrrnrrnrecrmmsmesneeecne en | t 25.0 KHZ 5.0 ms 10.0 ms Transient Frequency Behavior for Equipment Designed to Operate on 12.5 kHz Channels fp B uen snn in n ce nc nrnnr esnc recresrenrerrerrerrerrerrerrerrerenreerecrereereeeeeeee e | & 12.5 KHZ 5.0 ms 10.0 ms fp ol l lc llzzzll2.22222. £ 6.25 kHz 20.0 ms 25.0 ms t14 .. +12.5 kHz 5.0 ms 10.0 ms Transient Frequency Behavior for Equipment Designed to Operate on 6.25 kHz Channels o Eed 12r 5.0 ms 10.0 ms hy ienscesn o Te ol A S 20.0 ms 25.0 ms EB B 2 onl onl olsn n en nrnnrncrncrnsresrrrerrerresreresiesenrrnrrnerermereemeneereereceeceeciill. it 6.25 KHZ 5.0 ms 10.0 ms 1t.. is the instant when a 1 kHz test signal is completely suppressed, including any capture time due to phasing. t; is the time period immediately following t;,. t is the time period immediately following ti. t; is the time period from the instant when the transmitter is turned off until t#. tog is the instant when the 1 kHz test signal starts to rise. 2 During the time from the end of t to the beginning of t;, the frequency difference must not exceed the limits specified in §90.213. 3 Difference between the actual transmitter frequency and the assi?‘ned transmitter frequen%y. * If the transmitter carrier output power rating is 6 watts or less, the frequency difference during this time period may exceed the maximum frequency difference for this time period. 11.2 TEST METHOD TIMEIA—603 2.2.19.3 The results s 6 .u fi%@)} ost report refer only to the sample(s) tested unless otherwise stated and the sample(s) are retained for 30 days only. The document is issued b , this docu/m'; it cannot be reproduced except in full with our prior written permission. The more details and the authenticity of the report will be confirmed tfittp://www.agc-«& t.com. o Attestatic /2f Global Co pliance Tel: +86—755 2908 1955 Fax: +86—755 2600 8484 E—mail: agc@age—cert.com @ 400 089 2118 B# Add: 2/F. , Building 2, No.1—4, Chaxi Sanwei Technical Industrial Park,Gushu, Xixiang, Bacan District, Shenzhen, Guangdong China

Report No.: AGC02294181204FE10 Page 71 of 84 11.3 DESCRIBE LIMIT LINE OF RANSMITTER FREQUENCY BEHAVIOR ton: The switch-on instant ton of a transmitter is defined by the condition when the output power, measured at the antenna terminal, exceeds 0,1 % of the full output power (-30 dBc). t1: period of time starting at ton and finishing according to above 11.1 t2: period of time starting at the end of t1 and finishing according to above 11.1 toff: switch-off instant defined by the condition when the output power falls below 0,1 % of the full output power (-30 dBc). t3: period of time that finishing at toff and starting according to above 11.1

Report No.: AGC02294181204FE10 Page 72 of 84 11.4 MEASURE RESULT UHF: Transmitter Frequency Behavior @ 12.5 KHz Channel Separation--Off to On Transmitter Frequency Behavior @ 12.5 KHz Channel Separation--On to Off

Report No.: AGC02294181204FE10 Page 73 of 84 12. AUDIO LOW PASS FILTER RESPONSE 12.1.TEST LIMITS 2.1047(a): Voice modulated communication equipment. A curve or equivalent data showing the frequency response of the audio modulating circuit over a range of 100 to 5000 Hz shall be submitted. For equipment required to have an audio low-pass filter, a curve showing the frequency response of the filter or of all circuitry installed between the modulation limiter and the modulated stage shall be submitted. 90.242(b)(8): Recommended audio filter attenuation characteristics are given below: 12.2. METHOD OF MEASUREMENTS The rated audio input signal was applied to the input of the audio low-pass filter (or of all modulation stages) using an audio oscillator, this input signal level and its corresponding output signal were then measured and recorded using the FFT Digital Spectrum Analyzer. Tests were repeated at different audio signal frequencies from 0 to 50 KHz.

Report No.: AGC02294181204FE10 Page 74 of 84 12.3.MEASURE RESULT Analog: 12.5 KHZ CHANNEL SPACING, F3E, FREQUENCY OF ALL MODULATION STATES (TEST RESULT FOR UHF)-2W Audio Frequency (kHz) Response Attenuation (dB) Limit (dB) 1 0 / 3 -2.67 0.00 4 -7.11 -5.00 5 -10.98 -8.87 6 -14.15 -12.04 7 -16.83 -14.72 8 -19.15 -17.04 9 -21.19 -19.08 10 -23.03 -20.92 15 -30.11 -28.00 20 -30.11 -28.00 30 -30.11 -28.00 50 -30.11 -28.00 70 -30.11 -28.00

Report No.: AGC02294181204FE10 Page 75 of 84 APPENDIX I: PHOTOGRAPHS OF SETUP RADIATED EMISSION TEST SETUP

® A\G 7 HA 1 iX /:\%stag:of Global Compliance Report No.: AGC02294181204FE10 Page 76 of 84 CONDUCTED TEST SETUP The results ,m,Stisori o thisfea get report refer only to the sample(s) tested unless otherwise stated and the sample(s) are retained for 30 days only. The document is issued byKGE, h this dom/f&é tfittp://www.agc% Tel: +86—755 2908 1955 Fax: +86—755 2600 8484 E—mail: agc@age—cert.com @ 400 089 2118 Add: 2/F. , Building 2, No.1—4, Chaxi Sanwei Technical Industrial Park,Gushu, Xixiang, Bacan District, Shenzhen, Guangdong China

Report No.: AGC02294181204FE10 Page 77 of 84 APPENDIX II PHOTOGRAPHS OF EUT TOTAL VIEW OF EUT TOP VIEW OF EUT

Report No.: AGC02294181204FE10 Page 78 of 84 BOTTOM VIEW OF EUT FRONT VIEW OF EUT

Report No.: AGC02294181204FE10 Page 79 of 84 BACK VIEW OF EUT LEFT VIEW OF EUT

Report No.: AGC02294181204FE10 Page 80 of 84 RIGHT VIEW OF EUT OPEN VIEW-1 OF EUT

Report No.: AGC02294181204FE10 Page 81 of 84 OPEN VIEW-2 OF EUT Antenna OPEN VIEW-3 OF EUT

Report No.: AGC02294181204FE10 Page 82 of 84 INTERNAL VIEW-1 OF EUT INTERNAL VIEW-2 OF EUT

Report No.: AGC02294181204FE10 Page 83 of 84 INTERNAL VIEW-3 OF EUT INTERNAL VIEW-4 OF EUT

Report No.: AGC02294181204FE10 Page 84 of 84 INTERNAL VIEW-5 OF EUT ----END OF REPORT----


Document Created: 2019-06-13 12:06:06
Document Modified: 2019-06-13 12:06:06
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC