TEST REPORT

FCC ID: Q9S07161688P

Test Report

Download: PDF

FCCID_489151

$TIMCO ENGINEERING INC. 849 NW State Road 45 Newberry, Florida 32669 http://www.timcoengr.com 888.472.2424 F 352.472.2030 email: sid@timcoengr.com APPLICANT: ADVANCED WIRELESS COMMUNICATIONS FCC ID: Q9S07161688P TABLE OF CONTENTS LIST TEST REPORT: PAGE 1...........GENERAL INFORMATION & TECHNICAL DESCRIPTION PAGE 2...........TECHNICAL DESCRIPTION CONTINUED RF POWER OUTPUT PAGE 3...........MODULATION CHARACTERISTICS AUDIO FREQUENCY RESPONSE PAGE 4...........AUDIO LOW PASS FILTER PAGE 5...........MODULATION LIMITING PLOT PAGE 6-7.........OCCUPIED BANDWIDTH PAGE 8...........OCCUPIED BANDWIDTH PLOT PAGE 9...........SPURIOUS EMISSIONS AT ANTENNA TERMINALS PAGE 10..........METHOD OF MEASURING SPURIOUS EMISSIONS AT ANTENNA TERMINALS PAGE 11-12.......FIELD STRENGTH OF SPURIOUS EMISSIONS PAGE 13..........METHOD OF MEASURING RADIATED SPURIOUS EMISSIONS PAGE 14..........FREQUENCY STABILITY PAGE 15-16.......TRANSIENT FREQUENCY STABILITY PAGE 17..........TRANSIENT FREQUENCY RESPONSE PLOTS PAGE 18..........EQUIPMENT LIST APPLICANT: ADVANCED WIRELESS COMMUNICATIONS FCC ID: Q9S07161688P REPORT #: A\ADVANCED WIRELESS_Q9S\1435AUT4\1435AUT4TestReport.doc TABLE OF CONTENTS$

$TIMCO ENGINEERING INC. 849 NW State Road 45 Newberry, Florida 32669 http://www.timcoengr.com 888.472.2424 F 352.472.2030 email: sid@timcoengr.com GENERAL INFORMATION REQUIRED FOR CERTIFICATION OF A LICENSED TRANSMITTER 2.1033(c)(1)(2) ADVANCED WIRELESS COMMUNICATIONS will manufacture the FCCID: Q9S07161688P UHF TRANSCEIVER in quantity, for use under FCC RULES PART 90. ADVANCED WIRELESS COMMUNICATIONS 20809 KENSINGTON BLVD. LAKEVILLE, MINNESOTA 55044 2.1033(c) TECHNICAL DESCRIPTION 2.1033(c)(3) Users Manual: A draft copy of the instruction manual is included. 2.1033(c) (4) Type of Emission: 10K4F3E 90.209 90.207 Bn = 2M + 2DK M = 3000 D = 2200 Bn = 2(3000) + 2(2200) = 10.4k 2.1033(c)(5) Frequency Range: 460 - 470 MHz 90.209 (b)(5) 2.1033(c)(6)(7) Power Output shall not exceed 59 Watts into a 50 ohm 90.205 resistive load. There are no user power controls. 2.1033(c)(8) DC Voltages and Current into Final Amplifier: POWER INPUT: FINAL AMPLIFIER ONLY INPUT POWER: (4.5 V)(1.40 A) = 6.30 Watts 2.1033(c)(9) Tune-up procedure. The tune-up procedure is included. 2.1033(c)(10) Complete Circuit Diagrams: The circuit diagram and block diagram are included. 2.1033(c)(11): Description of all circuitry and devices provided for determining and stabilizing frequency is included in the circuit description. 2.1033(c)(12) A photograph or drawing of the equipment identification label is included. APPLICANT: ADVANCED WIRELESS COMMUNICATIONS FCC ID: Q9S07161688P REPORT #: A\ADVANCED WIRELESS_Q9S\1435AUT4\1435AUT4TestReport.doc Page 1 of 18$

$TIMCO ENGINEERING INC. 849 NW State Road 45 Newberry, Florida 32669 http://www.timcoengr.com 888.472.2424 F 352.472.2030 email: sid@timcoengr.com 2.1047(a)(b) Modulation characteristics: AUDIO FREQUENCY RESPONSE The audio frequency response was measured in accordance with TIA/EIA Specification 603. A curve or equivalent data showing the frequency response of the audio modulating circuit over a range of 100 – 5000Hz shall be submitted. The audio frequency response curve is shown below. Audio Frequency Response +5 +0 d B -5 -10 100 200 300 400 500 700 1k 2k 3k Hz APPLICANT: ADVANCED WIRELESS COMMUNICATIONS FCC ID: Q9S07161688P REPORT #: A\ADVANCED WIRELESS_Q9S\1435AUT4\1435AUT4TestReport.doc Page 3 of 18$

$TIMCO ENGINEERING INC. 849 NW State Road 45 Newberry, Florida 32669 http://www.timcoengr.com 888.472.2424 F 352.472.2030 email: sid@timcoengr.com 2.1047(a) Voice modulated communication equipment: For equipment required to have an audio low-pass filter, a curve showing the frequency response of the filter, or of all the circuitry installed between the modulation limiter and the modulated stage shall be submitted. Audio Low Pass Filter +5 +0 d B -5 -10 2k 3k 4k 5k 6k 7k 8k 10k 20k Hz APPLICANT: ADVANCED WIRELESS COMMUNICATIONS FCC ID: Q9S07161688P REPORT #: A\ADVANCED WIRELESS_Q9S\1435AUT4\1435AUT4TestReport.doc Page 4 of 18$

$TIMCO ENGINEERING INC. 849 NW State Road 45 Newberry, Florida 32669 http://www.timcoengr.com 888.472.2424 F 352.472.2030 email: sid@timcoengr.com 2.1047(b) Audio input versus modulation The audio input level needed for a particular percentage of modulation was measured in accordance with TIA/EIA Specification 603. The audio input curves versus modulation are shown below. Curves are provided for audio input frequencies of 300, 1000, and 2500 Hz. Modulation Limiting Plots: 2.5 KHz (Green), 1.0 KHz (Blue), and 300 Hz (Yellow) 2.2 k H z -25 -20 -15 -10 -5 +0 +5 +10 +15 dBu APPLICANT: ADVANCED WIRELESS COMMUNICATIONS FCC ID: Q9S07161688P REPORT #: A\ADVANCED WIRELESS_Q9S\1435AUT4\1435AUT4TestReport.doc Page 5 of 18$

$TIMCO ENGINEERING INC. 849 NW State Road 45 Newberry, Florida 32669 http://www.timcoengr.com 888.472.2424 F 352.472.2030 email: sid@timcoengr.com 2.1049 Occupied bandwidth: 2.1049(c) EMISSION BANDWIDTH: 90.210(b) 25kHz Channel Spacing: Data in the plots show that on any frequency removed from the assigned frequency by more than 50%, but not more than 100%: At least 25dB. On any frequency removed from the assigned frequency by more than 100%, but not more than 250%: At least 35 dB. On any frequency removed from the assigned frequency by more than 250%, of the authorized bandwidth: At least 43 + 10log(P)dB. 90.210(c) 12.5kHz Channel Spacing Not Equipped with a Low Pass Filter: For transmitters that are not equipped with an audio low pass filter pursuant to S90.211 (b), the power of any emission must be attenuated below the un-modulated carrier output power as follows; (1) On any frequency removed from the center of the authorized bandwidth by a displacement frequency (fd in kHz) of more than 5 kHz but not more than10 kHz: At least 83 log (fd/5) dB; (2) ON any frequency removed from the center of the authorized bandwidth by a displacement frequency (fd in kHz) of more than 10 kHz, but not more than 250% of the authorized bandwidth: At least 29 log(fd2/11)dB or 50 dB, whichever is the lesser attenuation; (3) On any frequency removed from the center of the authorized bandwidth by more than 250% of the authorized bandwidth: At least 43+10 log(Po)dB. 90.210(d) Emission Mask D - 12.5 kHz channel BW equipment: For transmitters designed to operate with a 12.5 kHz channel bandwidth, any emission must be attenuated below the power (P) of the highest emission contained within the authorized bandwidth as follows: (1) On any frequency from the center of the authorized bandwidth f0 to 5.625 kHz removed from f0: Zero dB. (2) On any frequency from the center of the authorized bandwidth by a displacement frequency (fd in kHz) of more than 5.625 kHz but no more than 12.5 kHz: At least 7.27 (fd - 2.88 kHz) dB. (3) On any frequency removed from the center of the authorized bandwidth by a displacement frequency (fd in kHz) of more than 12.5 kHz: At least 50 + 10log(P) dB or 70 dB, whichever is the lesser attenuation. APPLICANT: ADVANCED WIRELESS COMMUNICATIONS FCC ID: Q9S07161688P REPORT #: A\ADVANCED WIRELESS_Q9S\1435AUT4\1435AUT4TestReport.doc Page 6 of 18$

$TIMCO ENGINEERING INC. 849 NW State Road 45 Newberry, Florida 32669 http://www.timcoengr.com 888.472.2424 F 352.472.2030 email: sid@timcoengr.com 2.1051(a) Spurious emissions at antenna terminals (conducted): Data below shows the level of conducted spurious responses. The carrier was modulated 100% using a 2500 Hz tone. The spectrum was scanned from 0.4 to at least the 10th harmonic of the fundamental. The measurements were made in accordance with standard TIA/EIA-603. FCC Limit for: 12.5 kHz Spacing = 50.00 TEST DATA: dB below dB below TF EF carrier TF EF carrier 460 460 0.0 465 465 0.0 920 69.0 930 70.0 1380 73.0 1395 70.8 1840 70.1 1860 66.3 2300 67.7 2325 69.1 2760 59.7 2790 64.7 3220 71.3 3255 78.1 3680 76.7 3720 73.8 4140 65.5 4185 73.0 4600 91.9 4650 85.5 dB below TF EF carrier 470 470 0.0 940 69.0 1410 73.1 1880 67.5 2350 55.8 2820 52.8 3290 67.2 3760 61.2 4230 55.1 4700 71.2 APPLICANT: ADVANCED WIRELESS COMMUNICATIONS FCC ID: Q9S07161688P REPORT #: A\ADVANCED WIRELESS_Q9S\1435AUT4\1435AUT4TestReport.doc Page 9 of 18$

$TIMCO ENGINEERING INC. 849 NW State Road 45 Newberry, Florida 32669 http://www.timcoengr.com 888.472.2424 F 352.472.2030 email: sid@timcoengr.com Method of Measuring Conducted Spurious Emissions HP Spectrum Analyzer 8566B TRANSMITTER 50 OHM RESISTIVE UNDER TEST LOAD METHOD OF MEASUREMENT: The procedure used was TIA/EIA-603 STANDARD without any exceptions. The measurements were made at TIMCO ENGINEERING INC. 849 N.W. State Road 45, Newberry, Florida 32669. APPLICANT: ADVANCED WIRELESS COMMUNICATIONS FCC ID: Q9S07161688P REPORT #: A\ADVANCED WIRELESS_Q9S\1435AUT4\1435AUT4TestReport.doc Page 10 of 18$

$TIMCO ENGINEERING INC. 849 NW State Road 45 Newberry, Florida 32669 http://www.timcoengr.com 888.472.2424 F 352.472.2030 email: sid@timcoengr.com 2.1053 Field strength of spurious emissions: NAME OF TEST: RADIATED SPURIOUS EMISSIONS REQUIREMENTS: The FCC Limits for radiated emissions are the same as previously stated for the conducted emissions. TEST DATA (460 MHz): Emission Ant. Corrected Coax Substitution dB Frequency Polarity EUT Loss Antenna Below MHz Signal (dB) (dBd) Carrier Reading (dBc) 460.00 V 30.40 0 -0.49 0 920.00 V -37.10 0 -0.79 67.8 1380.00 V -35.20 1.08 4.47 61.72 1840.00 V -25.10 1.17 5.22 50.96 2300.00 V -35.30 1.26 6.19 60.28 2760.00 V -32.10 1.33 6.96 56.38 3220.00 H -41.90 1.37 7.33 65.85 3680.00 H -39.90 1.42 7.59 63.64 4140.00 H -32.30 1.46 7.82 55.85 4600.00 H -41.60 1.52 8.13 64.9 TEST DATA (465 MHz): Emission Ant. Corrected Coax Substitution dB Frequency Polarity EUT Loss Antenna Below MHz Signal (dB) (dBd) Carrier Reading (dBc) 465.00 V 30.65 0 -0.51 0 930.00 V -39.30 0 -0.91 70.35 1395.00 V -37.80 1.08 4.53 64.49 1860.00 V -26.10 1.17 5.24 52.17 2325.00 V -29.10 1.27 6.26 54.25 2790.00 V -32.70 1.33 6.98 57.19 3255.00 H -35.90 1.38 7.35 60.07 3720.00 H -33.00 1.42 7.59 56.97 4185.00 V -31.20 1.47 7.87 54.94 4650.00 H -35.80 1.53 8.07 59.4 APPLICANT: ADVANCED WIRELESS COMMUNICATIONS FCC ID: Q9S07161688P REPORT #: A\ADVANCED WIRELESS_Q9S\1435AUT4\1435AUT4TestReport.doc Page 11 of 18$

$TIMCO ENGINEERING INC. 849 NW State Road 45 Newberry, Florida 32669 http://www.timcoengr.com 888.472.2424 F 352.472.2030 email: sid@timcoengr.com 2.1055 Frequency stability: 90.213(a)(1) 90.266(b)(3) Frequency Stability Requirement: 5 ppm Temperature range requirements: -30 to +50º C. Voltage Variation +,- 15%. Measurement procedure per TIA/EIA 603. MEASUREMENT DATA: Assigned Frequency (Ref. Frequency): 464.987 517 MHz TEMPERATURE_°C FREQUENCY_MHz PPM REFERENCE_____________ 464.987 517 00.0 -30___________________ 464.987 748 + 0.50 -20___________________ 464.987 614 + 0.21 -10___________________ 464.987 496 - 0.05 0___________________ 464.987 455 - 0.13 +10___________________ 464.987 491 - 0.06 +20___________________ 464.987 517 0.00 +30___________________ 464.987 477 - 0.09 +40___________________ 464.987 377 - 0.30 +50___________________ 464.987 203 - 0.67 %BATT. DATA PPM -15% 464.987 529 + 0.03 RESULTS OF MEASUREMENTS: The test results indicates that the EUT meets the requirements. APPLICANT: ADVANCED WIRELESS COMMUNICATIONS FCC ID: Q9S07161688P REPORT #: A\ADVANCED WIRELESS_Q9S\1435AUT4\1435AUT4TestReport.doc Page 14 of 18$

$TIMCO ENGINEERING INC. 849 NW State Road 45 Newberry, Florida 32669 http://www.timcoengr.com 888.472.2424 F 352.472.2030 email: sid@timcoengr.com 2.1055(a)(1) Frequency stability: 90.214 Transient Frequency Behavior REQUIREMENTS: Transmitters designed to operate in the 150 - 174 MHz and 421 - 512 MHz frequency bands must maintain transient frequencies within the maximum transient frequencies within the maximum frequency difference limits during the time intervals indicated: Time Intervals Maximum frequency All Equipment difference 150-174 MHz 421-512 MHz Transient Frequency Behavior for Equipment Designed to Operate on 25 kHz Channels t14 ±25.0 kHz 5.0 mS 10.0 mS t2 ±12.5 kHz 20.0 mS 25.0 mS t34 ±25.0 kHz 5.0 mS 10.0 mS Transient Frequency Behavior for Equipment Designed to Operate on 12.5 kHz Channels t14 ±12.5 kHz 5.0 mS 10.0 mS t2 ±6.25 kHz 20.0 mS 25.0 mS t34 ±12.5 kHz 5.0 mS 10.0 mS Transient Frequency Behavior for Equipment Designed to Operate on 6.25 kHz Channels t14 ±6.25 kHz 5.0 mS 10.0 mS t2 ±3.125 kHz 20.0 mS 25.0 mS t34 ±6.25 kHz 5.0 mS 10.0 mS APPLICANT: ADVANCED WIRELESS COMMUNICATIONS FCC ID: Q9S07161688P REPORT #: A\ADVANCED WIRELESS_Q9S\1435AUT4\1435AUT4TestReport.doc Page 15 of 18$

$TIMCO ENGINEERING INC. 849 NW State Road 45 Newberry, Florida 32669 http://www.timcoengr.com 888.472.2424 F 352.472.2030 email: sid@timcoengr.com EMC Equipment List Device Manufacturer Model Serial Cal/Char Due Date Number Date Tan Tower HP 8566B Opt 3138A07786 CAL 9/23/03 9/23/05 Spectrum 462 3144A20661 Analyzer Tan Tower RF HP 85685A 3221A01400 CAL 9/23/03 9/23/05 Preselector Tan Tower HP 85650A 3303A01690 CAL 9/23/03 9/23/05 Quasi-Peak Adapter Tan Tower HP 8449B-H02 3008A00372 CAL 9/23/03 9/23/05 Preamplifier Biconnical Electro- BIA-25 1171 CAL 8/17/04 8/17/06 Antenna Metrics Log-Periodic Electro- LPA-25 1122 CAL 8/14/04 8/26/04 Antenna Metrics Double- Electro- RGA-180 2319 CAL 2/17/03 2/17/05 Ridged Horn Metrics Antenna LISN Electro- ANS-25/2 2604 CAL 8/27/04 8/27/06 Metrics Termaline Bird 611 16405 CAL 7/16/04 7/16/04 Wattmeter Electronic Corporation Oscilloscope Tektronix 2230 300572 CAL 7/3/03 7/3/05 Peak Power HP 8900C 2131A00545 CAL 7/2/03 7/2/05 Meter Power Sensor Agilent 84811A 2551A02705 CAL 7/2/03 7/2/05 Technologies Power Meter HP 432A 1141A07655 CAL 4/15/03 4/15/05 Digital Fluke 2166A 42032 out for cal Thermometer Frequency HP 5352B 2632A00165 CAL 8/3/04 8/3/06 Counter Signal HP 8640B 2308A21464 CAL 8/26/04 8/26/04 Generator APPLICANT: ADVANCED WIRELESS COMMUNICATIONS FCC ID: Q9S07161688P REPORT #: A\ADVANCED WIRELESS_Q9S\1435AUT4\1435AUT4TestReport.doc Page 18 of 18$

Document Created: 2004-11-11 09:31:27
Document Modified: 2004-11-11 09:31:27