MPE

FCC ID: Q9S-AWR991

RF Exposure Info

Download: PDF

FCCID_1892638

Report No.: AGC07B130101F7
Page 2 of 8
TABALE OF CONTENTS

TABALE OF CONTENTS .................................................................................................................................. 2
1. TEST RESULT CERTIFICATION ................................................................................................................... 3
2. TECHNICAL INFORMATION ......................................................................................................................... 4
3. RF EXPOSURE MEASUREMENT................................................................................................................. 5
3.1 INTRODUCTION ...................................................................................................................................... 5
3.2 FCC LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) .......................................................... 6
4. CLASSIFICATION OF THE ASSESSMENT METHODS ............................................................................... 7
5. EUT OPERATION CONDITION ..................................................................................................................... 7
6. TEST RESULTS ............................................................................................................................................. 8

Report No.: AGC07B130101F7
Page 5 of 8
3. RF EXPOSURE MEASUREMENT
3.1 INTRODUCTION

Human exposure to RF emissions from mobile devices (47 CFR §2.1091) may be evaluated based on the MPE
limits adopted by the FCC for electric and magnetic field strength and/or power density, as appropriate, since
exposures are assumed to occur at distances of 20 cm or more from persons.

The 1992 ANSI/IEEE standard (See Listed limit table) specifies a minimum separation distance of 20 cm for
performing reliable field measurements to determine adherence to MPE limits.

If the minimum separation distance between a transmitter and nearby persons is more than 20 cm under
normal operating conditions, compliance with MPE limits may be determined at such distance from the
transmitter. When applicable, operation instructions and prominent warning labels may be used to alert
the exposed persons to maintain a specified distance from the transmitter or to limit their exposure
durations and usage conditions to ensure compliance.

Report No.: AGC07B130101F7
Page 6 of 8
3.2 FCC LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE)

LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE
Frequency Magnetic Field Power Density Averaging Time
E-field Strength (E)
Range Strength (H) (S) |E|2, |H|2 or S
(V/m)
(MHz) (A/m) (mW/cm2) (Minutes)
0.3 -- 1.34 614 1.63 (100)* 30
2
1.34 -- 30 824/f 2.19/f (180/f )* 30
30 -- 300 27.5 0.073 0.2 30
300 -- 1500 -- -- f/1500 30
1500 -- 100,000 -- -- 1.0 30

*Note:
1. f= Frequency in MHz * Plane-wave Equivalent Power Density
2. The averaging time for General Population/Uncontrolled exposure to fixed transmitters is not applicable
for mobile and portable transmitters. See 47 CFR §§2.1091 and 2.1093 on source-based time-averaging
requirement for mobile and portable transmitters.

Report No.: AGC07B130101F7
Page 7 of 8
4. CLASSIFICATION OF THE ASSESSMENT METHODS
According to user manual, The antenna of the product, under normal use condition is at least 0.3m away from
the body of the user. Warning statement to the user for keeping at least 30cm separation distance and the
prohibition of operating to a person has been printed on the user’s manual. So, this product under normal use is
located on electromagnetic far field between the human body.

S=PG/4πR²
Where:
S=power density
P=power input to antenna
G=power gain of the antenna in the direction of interest relative to an isotropic radiator R=distance to the center
of radiation of the antenna

5. EUT OPERATION CONDITION

Make the EUT to transmit at lowest, middle and highest channel individually.

Report No.: AGC07B130101F7
Page 8 of 8
6. TEST RESULTS
Note: report the worst result in this part.
Antenna Gain=0dBi (Numeric 1.0), π=3.141

Output Output Power Density
Frequency Power Density Result
Power Power Limit

MHz dBm mW mW/cm2 mW/cm2 Pass/Fail

469.975 32.26 1683 0.15 0.31 Pass

Note: The output power is refer to AGC07B130101F2.
According to the user manual, the minimum separate distance which used for MPE calculate is 0.3m.

Document Created: 2013-01-21 11:29:41
Document Modified: 2013-01-21 11:29:41

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC