Test Report_20181010_v1 - 1807TW0111-U6-Co-location Test Report

FCC ID: Q9DAPIN0514515

Test Report

Download: PDF
FCCID_4071579

MRT Technology (Taiwan) Co., Ltd Report No.: 1807TW0111-U6 Phone: +886-3-3288388 Report Version: V01 Web: www.mrt-cert.com Issue Date: 09-30-2018 Co-location Report FCC ID: Q9DAPIN0514515 APPLICANT: Hewlett Packard Enterprise Company Application Type: Certification Product: ACCESS POINT Model No.: APIN0514, APIN0515 Brand Name: , FCC Rule Part(s): Part15 Subpart C (Section 15.247) Part15 Subpart E (Section 15.407) Test Date: June 19 ~ September 25, 2018 Reviewed By: ( Paddy Chen ) Approved By: ( Chenz Ker ) The test results relate only to the samples tested. This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in ANSI C63.4-2013. Test results reported herein relate only to the item(s) tested. The test report shall not be reproduced except in full without the written approval of MRT Technology (Taiwan) Co., Ltd. FCC ID: Q9DAPIN0514515 Page Number: 1 of 12

Report No.: 1807TW0111-U6 Revision History Report No. Version Description Issue Date Note 1807TW0111-U6 Rev. 01 Initial report 09-30-2018 Valid FCC ID: Q9DAPIN0514515 Page Number: 2 of 12

Report No.: 1807TW0111-U6 1. TEST RESULT of Radiated Emissions for Co-located Test Mode: 2.4GHz, 5GHz Wi-Fi + BLE Transmit Test Site: AC1 Test Engineer: Kevin Polarity: Horizontal Antenna Type: Omni Antenna (M/N: AP-ANT-20W) Model No.: APIN0514 Remark: There is the ambient noise within frequency range 9kHz~30MHz and 18GHz~40GHz, the permissible value is not show in the report. No Flag Mark Frequency Measure Reading Over Limit Limit Factor Type (MHz) Level Level (dB) (dBuV/m) (dB) (dBuV/m) (dBuV) 1 6431.500 46.717 38.815 -27.283 74.000 7.903 PK 2 6431.500 32.192 24.290 -21.808 54.000 7.903 AV 3 7205.000 49.576 37.476 -24.424 74.000 12.100 PK 4 7205.000 36.290 24.190 -17.710 54.000 12.100 AV 5 9389.500 50.423 35.932 -23.577 74.000 14.491 PK 6 * 9389.500 37.051 22.560 -16.949 54.000 14.491 AV Note 1: Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) - Pre_Amplifier Gain (dB). Note 2: We selected the 2.4GHz and 5GHz worst-case mode of radiated spurious emissions in the DTS and UNII reports. Note 3: 2.4GHz Wi-Fi 802.11b Channel 2412MHz Power setting = 76; 5GHz Wi-Fi 802.11ac-VHT20 Channel 5240MHz Power setting = 75; 2.4GHz Bluetooth LE channel 2402MHz Power setting = 8; Note 4: ZigBee and Bluetooth-LE can’t transmit simultaneously and Bluetooth-LE power higher than ZigBee, so we only assess the WIFI and Bluetooth-LE simultaneous transmission. FCC ID: Q9DAPIN0514515 Page Number: 3 of 12

Report No.: 1807TW0111-U6 Test Mode: 2.4GHz, 5GHz Wi-Fi + BLE Transmit Test Site: AC1 Test Engineer: Kevin Polarity: Vertical Antenna Type: Omni Antenna (M/N: AP-ANT-20W) Model No.: APIN0514 Remark: There is the ambient noise within frequency range 9kHz~30MHz and 18GHz~40GHz, the permissible value is not show in the report. No Flag Mark Frequency Measure Reading Over Limit Limit Factor Type (MHz) Level Level (dB) (dBuV/m) (dB) (dBuV/m) (dBuV) 1 6576.000 46.207 37.574 -27.793 74.000 8.633 PK 2 6576.000 31.823 23.190 -22.177 54.000 8.633 AV 3 7927.500 50.120 37.680 -23.880 74.000 12.441 PK 4 7927.500 36.020 23.580 -17.980 54.000 12.441 AV 5 10061.000 53.150 37.593 -20.850 74.000 15.557 PK 6 * 10061.000 40.467 24.910 -13.533 54.000 15.557 AV Note 1: Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) - Pre_Amplifier Gain (dB). Note 2: We selected the 2.4GHz and 5GHz worst-case mode of radiated spurious emissions in the DTS and UNII reports. Note 3: 2.4GHz Wi-Fi 802.11b Channel 2412MHz Power setting = 76; 5GHz Wi-Fi 802.11ac-VHT20 Channel 5240MHz Power setting = 75; 2.4GHz Bluetooth LE channel 2402MHz Power setting = 8; Note 4: ZigBee and Bluetooth-LE can’t transmit simultaneously and Bluetooth-LE power higher than ZigBee, so we only assess the WIFI and Bluetooth-LE simultaneous transmission. FCC ID: Q9DAPIN0514515 Page Number: 4 of 12

Report No.: 1807TW0111-U6 Test Mode: 2.4GHz, 5GHz Wi-Fi + BLE Transmit Test Site: AC1 Test Engineer: Kevin Polarity: Horizontal Antenna Type: Omni Antenna (M/N: AP-ANT-40) Model No.: APIN0514 Remark: There is the ambient noise within frequency range 9kHz~30MHz and 18GHz~40GHz, the permissible value is not show in the report. No Flag Mark Frequency Measure Reading Over Limit Limit Factor Type (MHz) Level Level (dB) (dBuV/m) (dB) (dBuV/m) (dBuV) 1 7086.000 48.612 37.273 -25.388 74.000 11.339 PK 2 7086.000 34.349 23.010 -19.651 54.000 11.339 AV 3 7944.500 50.251 37.797 -23.749 74.000 12.454 PK 4 7944.500 36.304 23.850 -17.696 54.000 12.454 AV 5 9857.000 51.018 34.831 -22.982 74.000 16.187 PK 6 * 9857.000 38.567 22.380 -15.433 54.000 16.187 AV Note 1: Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) - Pre_Amplifier Gain (dB). Note 2: We selected the 2.4GHz and 5GHz worst-case mode of radiated spurious emissions in the DTS and UNII reports. Note 3: 2.4GHz Wi-Fi 802.11b Channel 2437MHz Power setting =75; 5GHz Wi-Fi 802.11ac-VHT20 Channel 5240MHz Power setting = 75; 2.4GHz Bluetooth LE channel 2402MHz Power setting = 8; Note 4: ZigBee and Bluetooth-LE can’t transmit simultaneously and Bluetooth-LE power higher than ZigBee, so we only assess the WIFI and Bluetooth-LE simultaneous transmission. FCC ID: Q9DAPIN0514515 Page Number: 5 of 12

Report No.: 1807TW0111-U6 Test Mode: 2.4GHz, 5GHz Wi-Fi + BLE Transmit Test Site: AC1 Test Engineer: Kevin Polarity: Vertical Antenna Type: Omni Antenna (M/N: AP-ANT-40) Model No.: APIN0514 Remark: There is the ambient noise within frequency range 9kHz~30MHz and 18GHz~40GHz, the permissible value is not show in the report. No Flag Mark Frequency Measure Reading Over Limit Limit Factor Type (MHz) Level Level (dB) (dBuV/m) (dB) (dBuV/m) (dBuV) 1 5182.000 43.952 39.890 -30.048 74.000 4.062 PK 2 5182.000 28.942 24.880 -25.058 54.000 4.062 AV 3 7978.500 50.541 38.054 -23.459 74.000 12.487 PK 4 7978.500 36.327 23.840 -17.673 54.000 12.487 AV 5 9143.000 49.480 34.839 -24.520 74.000 14.641 PK 6 * 9143.000 37.131 22.490 -16.869 54.000 14.641 AV Note 1: Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) - Pre_Amplifier Gain (dB). Note 2: We selected the 2.4GHz and 5GHz worst-case mode of radiated spurious emissions in the DTS and UNII reports. Note 3: 2.4GHz Wi-Fi 802.11b Channel 2437MHz Power setting =75; 5GHz Wi-Fi 802.11ac-VHT20 Channel 5240MHz Power setting = 75; 2.4GHz Bluetooth LE channel 2402MHz Power setting = 8; Note 4: ZigBee and Bluetooth-LE can’t transmit simultaneously and Bluetooth-LE power higher than ZigBee, so we only assess the WIFI and Bluetooth-LE simultaneous transmission. FCC ID: Q9DAPIN0514515 Page Number: 6 of 12

Report No.: 1807TW0111-U6 Test Mode: 2.4GHz, 5GHz Wi-Fi + BLE Transmit Test Site: AC1 Test Engineer: Kevin Polarity: Horizontal Antenna Type: Omni Antenna (M/N: AP-ANT-19) Model No.: APIN0514 Remark: There is the ambient noise within frequency range 9kHz~30MHz and 18GHz~40GHz, the permissible value is not show in the report. No Flag Mark Frequency Measure Reading Over Limit Limit Factor Type (MHz) Level Level (dB) (dBuV/m) (dB) (dBuV/m) (dBuV) 1 6550.500 46.424 37.847 -27.576 74.000 8.577 PK 2 6550.500 32.167 23.590 -21.833 54.000 8.577 AV 3 7995.500 49.902 37.401 -24.098 74.000 12.501 PK 4 7995.500 36.081 23.580 -17.919 54.000 12.501 AV 5 9236.500 49.872 35.106 -24.128 74.000 14.766 PK 6 * 9236.500 37.236 22.470 -16.764 54.000 14.766 AV Note 1: Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) - Pre_Amplifier Gain (dB). Note 2: We selected the 2.4GHz and 5GHz worst-case mode of radiated spurious emissions in the DTS and UNII reports. Note 3: 2.4GHz Wi-Fi 802.11b Channel 2437MHz Power setting =75; 5GHz Wi-Fi 802.11ac-VHT20 Channel 5240MHz Power setting = 72; 2.4GHz Bluetooth LE channel 2402MHz Power setting = 8; Note 4: ZigBee and Bluetooth-LE can’t transmit simultaneously and Bluetooth-LE power higher than ZigBee, so we only assess the WIFI and Bluetooth-LE simultaneous transmission. FCC ID: Q9DAPIN0514515 Page Number: 7 of 12

Report No.: 1807TW0111-U6 Test Mode: 2.4GHz, 5GHz Wi-Fi + BLE Transmit Test Site: AC1 Test Engineer: Kevin Polarity: Vertical Antenna Type: Omni Antenna (M/N: AP-ANT-19) Model No.: APIN0514 Remark: There is the ambient noise within frequency range 9kHz~30MHz and 18GHz~40GHz, the permissible value is not show in the report. No Flag Mark Frequency Measure Reading Over Limit Limit Factor Type (MHz) Level Level (dB) (dBuV/m) (dB) (dBuV/m) (dBuV) 1 4289.500 44.038 42.512 -29.962 74.000 1.526 PK 2 4289.500 28.206 26.680 -25.794 54.000 1.526 AV 3 6440.000 47.114 39.155 -26.886 74.000 7.959 PK 4 6440.000 33.239 25.280 -20.761 54.000 7.959 AV 5 8012.500 49.986 37.485 -24.014 74.000 12.501 PK 6 * 8012.500 37.291 24.790 -16.709 54.000 12.501 AV Note 1: Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) - Pre_Amplifier Gain (dB). Note 2: We selected the 2.4GHz and 5GHz worst-case mode of radiated spurious emissions in the DTS and UNII reports. Note 3: 2.4GHz Wi-Fi 802.11b Channel 2437MHz Power setting =75; 5GHz Wi-Fi 802.11ac-VHT20 Channel 5240MHz Power setting = 72; 2.4GHz Bluetooth LE channel 2402MHz Power setting = 8; Note 4: ZigBee and Bluetooth-LE can’t transmit simultaneously and Bluetooth-LE power higher than ZigBee, so we only assess the WIFI and Bluetooth-LE simultaneous transmission. FCC ID: Q9DAPIN0514515 Page Number: 8 of 12

Report No.: 1807TW0111-U6 Test Mode: 2.4GHz, 5GHz Wi-Fi + BLE Transmit Test Site: AC1 Test Engineer: Kevin Polarity: Horizontal Antenna Type: Directional Antenna (M/N: AP-ANT-48) Model No.: APIN0514 Remark: There is the ambient noise within frequency range 9kHz~30MHz and 18GHz~40GHz, the permissible value is not show in the report. No Flag Mark Frequency Measure Reading Over Limit Limit Factor Type (MHz) Level Level (dB) (dBuV/m) (dB) (dBuV/m) (dBuV) 1 5165.000 44.662 40.540 -29.338 74.000 4.122 PK 2 5165.000 29.812 25.690 -24.188 54.000 4.122 AV 3 7681.000 49.575 37.113 -24.425 74.000 12.462 PK 4 7681.000 36.642 24.180 -17.358 54.000 12.462 AV 5 10299.000 52.073 35.480 -21.927 74.000 16.594 PK 6 * 10299.000 39.843 23.250 -14.157 54.000 16.594 AV Note 1: Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) - Pre_Amplifier Gain (dB). Note 2: We selected the 2.4GHz and 5GHz worst-case mode of radiated spurious emissions in the DTS and UNII reports. Note 3: 2.4GHz Wi-Fi 802.11b Channel 2437MHz Power setting =75; 5GHz Wi-Fi 802.11ac-VHT20 Channel 5240MHz Power setting = 67; 2.4GHz Bluetooth LE channel 2402MHz Power setting = 8; Note 4: ZigBee and Bluetooth-LE can’t transmit simultaneously and Bluetooth-LE power higher than ZigBee, so we only assess the WIFI and Bluetooth-LE simultaneous transmission. FCC ID: Q9DAPIN0514515 Page Number: 9 of 12

Report No.: 1807TW0111-U6 Test Mode: 2.4GHz, 5GHz Wi-Fi + BLE Transmit Test Site: AC1 Test Engineer: Kevin Polarity: Vertical Antenna Type: Directional Antenna (M/N: AP-ANT-48) Model No.: APIN0514 Remark: There is the ambient noise within frequency range 9kHz~30MHz and 18GHz~40GHz, the permissible value is not show in the report. No Flag Mark Frequency Measure Reading Over Limit Limit Factor Type (MHz) Level Level (dB) (dBuV/m) (dB) (dBuV/m) (dBuV) 1 7247.500 49.309 37.092 -24.691 74.000 12.217 PK 2 7247.500 36.397 24.180 -17.603 54.000 12.217 AV 3 8046.500 51.025 38.558 -22.975 74.000 12.468 PK 4 8046.500 37.427 24.960 -16.573 54.000 12.468 AV 5 10503.000 52.765 35.600 -21.235 74.000 17.165 PK 6 * 10503.000 40.525 23.360 -13.475 54.000 17.165 AV Note 1: Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) - Pre_Amplifier Gain (dB). Note 2: We selected the 2.4GHz and 5GHz worst-case mode of radiated spurious emissions in the DTS and UNII reports. Note 3: 2.4GHz Wi-Fi 802.11b Channel 2437MHz Power setting =75; 5GHz Wi-Fi 802.11ac-VHT20 Channel 5240MHz Power setting = 67; 2.4GHz Bluetooth LE channel 2402MHz Power setting = 8; Note 4: ZigBee and Bluetooth-LE can’t transmit simultaneously and Bluetooth-LE power higher than ZigBee, so we only assess the WIFI and Bluetooth-LE simultaneous transmission. FCC ID: Q9DAPIN0514515 Page Number: 10 of 12

Report No.: 1807TW0111-U6 Test Mode: 2.4GHz, 5GHz Wi-Fi + BLE Transmit Test Site: AC1 Test Engineer: Kevin Polarity: Horizontal Antenna Type: Internal Antenna Model No.: APIN0515 Remark: There is the ambient noise within frequency range 9kHz~30MHz and 18GHz~40GHz, the permissible value is not show in the report. No Flag Mark Frequency Measure Reading Over Limit Limit Factor Type (MHz) Level Level (dB) (dBuV/m) (dB) (dBuV/m) (dBuV) 1 6346.500 45.761 38.353 -28.239 74.000 7.408 PK 2 6346.500 34.248 26.840 -19.752 54.000 7.408 AV 3 7876.500 49.897 37.490 -24.103 74.000 12.407 PK 4 7876.500 37.527 25.120 -16.473 54.000 12.407 AV 5 9899.500 51.471 36.105 -22.529 74.000 15.366 PK 6 * 9899.500 40.116 24.750 -13.884 54.000 15.366 AV Note 1: Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) - Pre_Amplifier Gain (dB). Note 2: We selected the 2.4GHz and 5GHz worst-case mode of radiated spurious emissions in the DTS and UNII reports. Note 3: 2.4GHz Wi-Fi 802.11b Channel 2437MHz Power setting = 76; 5GHz Wi-Fi 802.11ax-VHE20 Channel 5825MHz Power setting = 74; 2.4GHz Bluetooth LE channel 2402MHz Power setting = 8; Note 4: ZigBee and Bluetooth-LE can’t transmit simultaneously and Bluetooth-LE power higher than ZigBee, so we only assess the WIFI and Bluetooth-LE simultaneous transmission. FCC ID: Q9DAPIN0514515 Page Number: 11 of 12

Report No.: 1807TW0111-U6 Test Mode: 2.4GHz, 5GHz Wi-Fi + BLE Transmit Test Site: AC1 Test Engineer: Kevin Polarity: Vertical Antenna Type: Internal Antenna Model No.: APIN0515 Remark: There is the ambient noise within frequency range 9kHz~30MHz and 18GHz~40GHz, the permissible value is not show in the report. No Flag Mark Frequency Measure Reading Over Limit Limit Factor Type (MHz) Level Level (dB) (dBuV/m) (dB) (dBuV/m) (dBuV) 1 6482.500 45.689 37.430 -28.311 74.000 8.258 PK 2 6482.500 32.999 24.740 -21.001 54.000 8.258 AV 3 7953.000 49.930 37.467 -24.070 74.000 12.463 PK 4 7953.000 37.783 25.320 -16.217 54.000 12.463 AV 5 10137.500 52.249 36.331 -21.751 74.000 15.918 PK 6 * 10137.500 41.388 25.470 -12.612 54.000 15.918 AV Note 1: Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) - Pre_Amplifier Gain (dB). Note 2: We selected the 2.4GHz and 5GHz worst-case mode of radiated spurious emissions in the DTS and UNII reports. Note 3: 2.4GHz Wi-Fi 802.11b Channel 2437MHz Power setting = 76; 5GHz Wi-Fi 802.11ax-VHE20 Channel 5825MHz Power setting = 74; 2.4GHz Bluetooth LE channel 2402MHz Power setting = 8; Note 4: ZigBee and Bluetooth-LE can’t transmit simultaneously and Bluetooth-LE power higher than ZigBee, so we only assess the WIFI and Bluetooth-LE simultaneous transmission. The End FCC ID: Q9DAPIN0514515 Page Number: 12 of 12


Document Created: 2018-10-10 18:18:42
Document Modified: 2018-10-10 18:18:42
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC