1906TW0102-U6-FCC Co-location Test Report

FCC ID: Q9DAPIN0504505

Test Report

Download: PDF
FCCID_4482223

MRT Technology (Taiwan) Co., Ltd Report No.: 1906TWO102—U6 A Phone: +886—3—3288388 Report Version: VO1 Web: www.mrt—cert.com Issue Date: 07—15—2019 Co—location Report FCC ID: Q9DAPINO504505 APPLICANT: Hewlett Packard Enterprise Company Application Type: Certification Product: ACCESS POINT Model No.: APINO504, APINO505 Brand Name: aruba a Hewlett Packard = Hewlett Packard Enterprise Enterprise company > FCC Rule Part(s): Part15 Subpart C (Section 15.247) Part15 Subpart E (Section 15.407) Test Date: June 10 ~ July 10, 2019 Reviewed By: /Da/;( Chen \\\\‘&Z/ —ELee# & L (Paddy Chen) M 1'AF Approved By @/”b/ /Kw %@g Testing Laboratory Ker) (Chenz Zululubs® 3261 The test results relate only to the samples tested. This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in ANSI C63.4—2013. Test results reported herein relate only to the item(s) tested. The test report shall not be reproduced except in full without the written approval of MRT Technology (Taiwan) Co., Ltd. FCC ID: QgDAPINO504505 Page Number: 1 of 18

% I‘ Report No.: 1906TWO102—U6 Revision History 1906TWO102—U6 Rev. 01 Initial report 07—15—2019 Valid FCC ID: Q9DAPINO504505 Page Number: 2 of 18

W‘W I Report No.: 1906TWO102—U6 1. Test Result of Radiated Emissions for Co—located Test Mode: 2.4GHz, 5GHz Wi—Fi + BLE Transmit Test Site: AC1 Test Engineer: Kevin Polarity: Horizontal Antenna Type: Omni Antenna (M/N: AP—ANT—20W) Model No.: APINO504 Remark: There is the ambient noise within frequency range 9kHz~30MHz and 18GHz~40GHz, the permissible value is not show in the report. 90 80 70 60 5 € ® f l4 5s 3 J 6 o 40 + & 2o 20 10 0 10 1000 10000 18000 Frequency(MHz) No Flag Mark Frequency Measure Reading Margin Limit Factor Type (MHz) Level Level (dB) (dBuV/m) (dB) (dBuV/m) (dBuV) 1 7409.000 46.325 34.600 —27.675 74.000 11.725 PK 2 7409.635 33.368 21.854 —20.632 54.000 11.514 AV 3 8242.000 46.572 34.266 —27.428 74.000 12.306 PK 4 8242.745 34.028 21.689 —19.972 54.000 12.339 AV 5 11276.500 51.297 33.759 —22.703 74.000 17.538 PK 6 * 11276.544 38.565 20.725 —15.435 54.000 17.840 AV Note 1: Measure Level (dBuV/m) = Reading Level (dBuV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) — Pre_Amplifier Gain (dB). Note 2: We selected the 2.4GHz and 5GHz worst—case mode of radiated spurious emissions in the DTS and UNII reports. Note 3: 2.4GHz Wi—Fi 802.11n—HT20 Channel 2437MHz Power setting = 80; 5GHz Wi—Fi 802.11ac—VHT20 Channel 5825MHz Power setting = 78; 2.4GHz Bluetooth LE channel 2402MHz Power setting = 8; Note 4: ZigBee and Bluetooth—LE can‘t transmit simultaneously and Bluetooth—LE power higher than ZigBee, so we only assess the WIFI and Bluetooth—LE simultaneous transmission. FCC ID: Q9DAPINO504505 Page Number: 3 of 18

W‘W I Report No.: 1906TWO102—U6 Test Mode: 2.4GHz, 5GHz Wi—Fi + BLE Transmit Test Site: AC1 Test Engineer: Kevin Polarity: Vertical Antenna Type: Omni Antenna (M/N: AP—ANT—20W) Model No.: APINO504 Remark: There is the ambient noise within frequency range 9kHz~30MHz and 18GHz~40GHz, the permissible value is not show in the report. 90 80 70 & 5 € so iz § 40 s# 54 30 20 10 0 10 1000 10000 18000 Frequency(MHz) No Flag Mark Frequency Measure Reading Margin Limit Factor Type (MHz) Level Level (dB) (dBuV/m) (dB) (dBuV/m) (dBuV) 1 7536.500 46.367 34.495 —27.633 74.000 11.871 PK 2 7536.541 33.299 21.547 —20.701 54.000 11.752 AV 3 8165.417 34.878 22.574 —19.122 54.000 12.304 AV 4 8165.500 48.124 35.733 —25.876 74.000 12.391 PK 5 11098.000 52.083 34.514 —21.917 74.000 17.569 PK 6 * 11098.554 39.538 21.865 —14.462 54.000 17.673 AV Note 1: Measure Level (dBuV/m) = Reading Level (dBuV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) — Pre_Amplifier Gain (dB). Note 2: We selected the 2.4GHz and 5GHz worst—case mode of radiated spurious emissions in the DTS and UNII reports. Note 3: 2.4GHz Wi—Fi 802.11n—HT20 Channel 2437MHz Power setting = 80; 5GHz Wi—Fi 802.11ac—VHT20 Channel 5825MHz Power setting = 78; 2.4GHz Bluetooth LE channel 2402MHz Power setting = 8; Note 4: ZigBee and Bluetooth—LE can‘t transmit simultaneously and Bluetooth—LE power higher than ZigBee, so we only assess the WIFI and Bluetooth—LE simultaneous transmission. FCC ID: Q9DAPINO504505 Page Number: 4 of 18

W‘W I Report No.: 1906TWO102—U6 Test Mode: 2.4GHz, 5GHz Wi—Fi + BLE Transmit Test Site: AC1 Test Engineer: Kevin Polarity: Horizontal Antenna Type: Directional Antenna (M/N: AP—ANT—28) Model No.: APINO504 Remark: There is the ambient noise within frequency range 9kHz~30MHz and 18GHz~40GHz, the permissible value is not show in the report. 90 80 70 C 5 — T 3 e 50 . 3 T 6 g 40 4. £ & 30 20 10 0 10 1000 10000 18000 Frequency(MHz) No Flag Mark Frequency Measure Reading Margin Limit Factor Type (MHz) Level Level (dB) (dBuV/m) (dB) (dBuV/m) (dBuV) 1 7443.000 46.960 35.067 —27.040 74.000 11.893 PK 2 7443.544 34.165 22.575 —19.835 54.000 11.590 AV 3 8216.500 47.759 35.488 —26.241 74.000 12.271 PK 4 8216.885 34.663 22.335 —19.337 54.000 12.328 AV 5 10826.000 51.982 34.337 —22.018 74.000 17.645 PK 6 * 10826.354 38.998 21.665 —15.002 54.000 17.333 AV Note 1: Measure Level (dBuV/m) = Reading Level (dBuV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) — Pre_Amplifier Gain (dB). Note 2: We selected the 2.4GHz and 5GHz worst—case mode of radiated spurious emissions in the DTS and UNII reports. Note 3: 2.4GHz Wi—Fi 802.11n—HT20 Channel 2437MHz Power setting = 80; 5GHz Wi—Fi 802.11ac—VHT20 Channel 5825MHz Power setting = 78; 2.4GHz Bluetooth LE channel 2402MHz Power setting = 8; Note 4: ZigBee and Bluetooth—LE can‘t transmit simultaneously and Bluetooth—LE power higher than ZigBee, so we only assess the WIFI and Bluetooth—LE simultaneous transmission. FCC ID: Q9DAPINO504505 Page Number: 5 of 18

W‘W I Report No.: 1906TWO102—U6 Test Mode: 2.4GHz, 5GHz Wi—Fi + BLE Transmit Test Site: AC1 Test Engineer: Kevin Polarity: Vertical Antenna Type: Directional Antenna (M/N: AP—ANT—28) Model No.: APINO504 Remark: There is the ambient noise within frequency range 9kHz~30MHz and 18GHz~40GHz, the permissible value is not show in the report. ap 80 70 60 5 E 50 _/ . 40 # £ & 30 20 10 0 10 1000 10000 18000 Frequency(MHz) No Flag Mark Frequency Measure Reading Margin Limit Factor Type (MHz) Level Level (dB) (dBuV/m) (dB) (dBuV/m) (dBuV) 1 7596.000 45.584 33.828 —28.416 74.000 11.756 PK 2 7596.545 32.359 20.544 —21.641 54.000 11.814 AV 3 8191.000 48.000 35.509 —26.000 74.000 12.491 PK 4 8191.545 34.432 22.115 —19.568 54.000 12.317 AV 5 11591.000 53.044 35.398 —20.956 74.000 17.646 PK 6 * 11591.554 40.596 22.588 —13.404 54.000 18.008 AV Note 1: Measure Level (dBuV/m) = Reading Level (dBuV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) — Pre_Amplifier Gain (dB). Note 2: We selected the 2.4GHz and 5GHz worst—case mode of radiated spurious emissions in the DTS and UNII reports. Note 3: 2.4GHz Wi—Fi 802.11n—HT20 Channel 2437MHz Power setting = 80; 5GHz Wi—Fi 802.11ac—VHT20 Channel 5825MHz Power setting = 78; 2.4GHz Bluetooth LE channel 2402MHz Power setting = 8; Note 4: ZigBee and Bluetooth—LE can‘t transmit simultaneously and Bluetooth—LE power higher than ZigBee, so we only assess the WIFI and Bluetooth—LE simultaneous transmission. FCC ID: Q9DAPINO504505 Page Number: 6 of 18

W‘W I Report No.: 1906TWO102—U6 Test Mode: 2.4GHz, 5GHz Wi—Fi + BLE Transmit Test Site: AC1 Test Engineer: Kevin Polarity: Horizontal Antenna Type: Internal Antenna Model No.: APINO505 Remark: There is the ambient noise within frequency range 9kHz~30MHz and 18GHz~40GHz, the permissible value is not show in the report. 90 80 70 i0 5 1 3 § € 50 3 6 g 40 3E £ & 30 20 10 0 10 1000 10000 18000 Frequency(MHz) No Flag Mark Frequency Measure Reading Margin Limit Factor Type (MHz) Level Level (dB) (dBuV/m) (dB) (dBuV/m) (dBuV) 1 7468.500 46.068 34.231 —27.932 74.000 11.837 PK 2 7468.558 33.209 21.565 —20.791 54.000 11.645 AV 3 8437.500 45.499 33.123 —28.501 74.000 12.376 PK 4 8437.985 32.881 20.454 —21.119 54.000 12.427 AV 5 12101.000 51.421 34.310 —22.579 74.000 17.111 PK 6 * 12101.545 39.662 21.845 —14.338 54.000 17.816 AV Note 1: Measure Level (dBuV/m) = Reading Level (dBuV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) — Pre_Amplifier Gain (dB). Note 2: We selected the 2.4GHz and 5GHz worst—case mode of radiated spurious emissions in the DTS and UNII reports. Note 3: 2.4GHz Wi—Fi 802.11b Channel 241 2MHz Power setting = 75; 5GHz Wi—Fi 802.11ac—VHT20 Channel 5745MHz Power setting = 78; 2.4GHz Bluetooth LE channel 2402MHz Power setting = 8; Note 4: ZigBee and Bluetooth—LE can‘t transmit simultaneously and Bluetooth—LE power higher than ZigBee, so we only assess the WIFI and Bluetooth—LE simultaneous transmission. FCC ID: Q9DAPINO504505 Page Number: 7 of 18

W‘W I Report No.: 1906TWO102—U6 Test Mode: 2.4GHz, 5GHz Wi—Fi + BLE Transmit Test Site: AC1 Test Engineer: Kevin Polarity: Vertical Antenna Type: Internal Antenna Model No.: APINO505 Remark: There is the ambient noise within frequency range 9kHz~30MHz and 18GHz~40GHz, the permissible value is not show in the report. 90 80 70 & 5 E 50 1J 3 6 © T 40 4 & 30 20 10 0 10 1000 10000 18000 Frequency(MHz) No Flag Mark Frequency Measure Reading Margin Limit Factor Type (MHz) Level Level (dB) (dBuV/m) (dB) (dBuV/m) (dBuV) 1 7630.000 45.717 34.029 —28.283 74.000 11.688 PK 2 7630.541 33.394 21.544 —20.606 54.000 11.850 AV 3 8174.000 47.399 35.016 —26.601 74.000 12.383 PK 4 8174.454 34.933 22.625 —19.067 54.000 12.308 AV 5 10783.500 52.596 35.104 —21.404 74.000 17.491 PK 6 * 10783.965 39.818 22.544 —14.182 54.000 17.273 AV Note 1: Measure Level (dBuV/m) = Reading Level (dBuV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) — Pre_Amplifier Gain (dB). Note 2: We selected the 2.4GHz and 5GHz worst—case mode of radiated spurious emissions in the DTS and UNII reports. Note 3: 2.4GHz Wi—Fi 802.11b Channel 241 2MHz Power setting = 75; 5GHz Wi—Fi 802.11ac—VHT20 Channel 5745MHz Power setting = 78; 2.4GHz Bluetooth LE channel 2402MHz Power setting = 8; Note 4: ZigBee and Bluetooth—LE can‘t transmit simultaneously and Bluetooth—LE power higher than ZigBee, so we only assess the WIFI and Bluetooth—LE simultaneous transmission. The End FCC ID: Q9DAPINO504505 Page Number: 8 of 18

Report No.: 1906TWO102—U6 MA Appendix A — Worse Case Radiated Spurious Emission Plot Site: ACG1 Time: 2019/06/24 — 23:45 Limit: FCC_Part15.209_RE(3m) Engineer: Kevin Ker Probe: BBHA9120D_1GHz_18GHz Polarity: Horizontal EUT: ACCESS POINT (APINO505) Power: By POE Test Mode: Transmit by BLE at channel 2480MHz 90 80| 60 Level(dBuV/m) %i & —10 1000 18000 Frequency(MHz) No Flag Mark Frequency Measure Reading Margin Limit Factor Type (MHz) Level Level (dB) (dBuV/m) (dBuV/m) (dBuV) 1 6015.000 44.101 36.582 —24.099 68.200 7.519 PK 2 6457.000 45.534 36.320 —22.666 68.200 9.214 PK 3 7332.500 47.212 35.550 —26.788 74.000 11.663 PK 4 8182.500 48.900 36.463 —25.100 74.000 12.436 PK 5 18000.000 63.394 35.070 —10.606 74.000 28.324 PK 6 * 18000.000 45.774 17.450 —8.226 54.000 28.324 AV Note1: Measure Level (dBuV/m) = Reading Level (dBuV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) NoteZ: The test trace (Frequency range 13GHz ~ 18GHz above average limit) is same as the ambient noise, we selected the highest peak level frequency and performed average emission testing again. FCC ID: Q9DAPINO504505 Page Number: 9 of 18

Report No.: 1906TWO102—U6 Site: ACG1 Time: 2019/06/24 — 23:49 Limit: FCC_Part15.209_RE(3m) Engineer: Kevin Ker Probe: BBHA9120D_1GHz_18GHz Polarity: Vertical EUT: ACCESS POINT (APINO505) Power: By POE Test Mode: Transmit by BLE at channel 2480MHz 90 80| 60 50| Level(dBuV/m) * MAL““"F" 30 20| 10 0 —10‘ 1000 10000 18000 Frequency(MHz) No Flag Mark Frequency Measure Reading Margin Limit Factor Type (MHz) Level Level (dB) (dBuV/m) (dBuV/m) (dBuV) 1 5896.000 44.104 36.605 —24.096 68.200 7.499 PK 2 6465.500 45.586 36.272 —22.614 68.200 9.314 PK 3 7596.000 49.382 37.626 —24.618 74.000 11.756 PK 4 8174.000 48.737 36.354 —25.263 74.000 12.383 PK 5 18000.000 62.440 34.116 —11.560 74.000 28.324 PK 6 * 18000.000 45.104 16.780 —8.896 54.000 28.324 AV Note1: Measure Level (dBuV/m) = Reading Level (dBuV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) NoteZ: The test trace (Frequency range 13GHz ~ 18GHz above average limit) is same as the ambient noise, we selected the highest peak level frequency and performed average emission testing again. FCC ID: Q9DAPINO504505 Page Number: 10 of 18

Report No.: 1906TWO102—U6 Site: ACG1 Time: 2019/07/13 — 23:45 Limit: FCC_Part15.209_RE(3m) Engineer: Kevin Ker Probe: BBHA9120D_1GHz_18GHz Polarity: Horizontal EUT: ACCESS POINT (APINO505) Power: By POE Test Mode: Transmit by ZigBee at channel 2405MHz 90 80| is O¥ 60 50| Level(dBuV/m) 40| 30| 20| 10 0 —10‘ 1000 10000 18000 Frequency(MHz) No Flag Mark Frequency Measure Reading Margin Limit Factor Type (MHz) Level Level (dB) (dBuV/m) (dBuV/m) (dBuV) 1 5777.000 42.451 35.250 —25.749 68.200 7.201 PK 2 6627.000 44.376 34.860 —23.824 68.200 9.516 PK 3 7536.500 46.411 34.539 —27.589 74.000 11.871 PK 4 8216.500 47.362 35.091 —26.638 74.000 12.271 PK 5 18000.000 61.882 33.558 —12.118 74.000 28.324 PK 6 * 18000.000 44.274 15.950 —9.726 54.000 28.324 AV Note1: Measure Level (dBuV/m) = Reading Level (dBuV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) NoteZ: The test trace (Frequency range 13GHz ~ 18GHz above average limit) is same as the ambient noise, we selected the highest peak level frequency and performed average emission testing again. FCC ID: Q9DAPINO504505 Page Number: 11 of 18

Report No.: 1906TWO102—U6 Site: ACG1 Time: 2019/07/13 — 23:46 Limit: FCC_Part15.209_RE(3m) Engineer: Kevin Ker Probe: BBHA9120D_1GHz_18GHz Polarity: Vertical EUT: ACCESS POINT (APINO505) Power: By POE Test Mode: Transmit by ZigBee at channel 2405MHz 90 80 60 50 Level(dBuV/m) 40 aW oruem,NA 20 10 0 —10 1000 10000 18000 Frequency(MHz) No Flag Mark Frequency Measure Reading Margin Limit Factor Type (MHz) Level Level (dB) (dBuV/m) (dBuV/m) (dBuV) 1 5989.500 43.719 36.301 —24.481 68.200 7.418 PK 2 6491.000 44.087 34.782 —24.113 68.200 9.305 PK 3 7511.000 47.095 35.175 —26.905 74.000 11.920 PK 4 8250.500 48.535 36.266 —25.465 74.000 12.270 PK 5 17974.500 61.538 33.416 —12.462 74.000 28.122 PK 6 * 17974.500 43.772 15.650 —10.228 54.000 28.122 AV Note1: Measure Level (dBuV/m) = Reading Level (dBuV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) NoteZ: The test trace (Frequency range 13GHz ~ 18GHz above average limit) is same as the ambient noise, we selected the highest peak level frequency and performed average emission testing again. FCC ID: Q9DAPINO504505 Page Number: 12 of 18

Report No.: 1906TWO102—U6 Site: ACG1 Time: 2019/06/27 — 04:54 Limit: FCC_Part15.209_RE(3m) Engineer: Kevin Ker Probe: BBHA9120D_1GHz_18GHz Polarity: Horizontal EUT: ACCESS POINT (APINO505) Power: By POE Test Mode: Transmit by 802.11ax—HE20 at channel 2462MHz Ant 0 + 1 90 ; 80| 70 60 50 Level(dBuV/m) 40| 30| 20| 10 0 | —10‘ 1000 10000 18000 Frequency(MHz) No Flag Mark Frequency Measure Reading Margin Limit Factor Type (MHz) Level Level (dB) (dBuV/m) (dB) (dBuV/m) (dBuV) 1 4077.000 40.100 25.040 —33.900 74.000 15.060 PK 2 4867.500 41.800 25.529 —32.200 74.000 16.271 PK 3 5879.000 43.100 25.730 —25.100 68.200 17.370 PK 4 6984.000 44.200 24.742 —24.000 68.200 19.458 PK 5 17974.500 61.757 39.904 —12.243 74.000 21.853 PK 6 * 17974.500 43.450 21.597 —10.550 54.000 21.853 AV Note1: Measure Level (dBuV/m) = Reading Level (dBuV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) NoteZ: The test trace (Frequency range 13GHz ~ 18GHz above average limit) is same as the ambient noise, we selected the highest peak level frequency and performed average emission testing again. FCC ID: Q9DAPINO504505 Page Number: 13 of 18

Report No.: 1906TWO102—U6 Site: ACG1 Time: 2019/06/27 — 04:55 Limit: FCC_Part15.209_RE(3m) Engineer: Kevin Ker Probe: BBHA9120D_1GHz_18GHz Polarity: Vertical EUT: ACCESS POINT (APINO505) Power: By POE Test Mode: Transmit by 802.11ax—HE20 at channel 2462MHz Ant 0 + 1 90 80| 70 60 J m _2 E 50| 2 4 *uyit E 1 3 * 4 & s 20| 10 0 —10‘ 1000 10000 18000 Frequency(MHz) No Flag Mark Frequency Measure Reading Margin Limit Factor Type (MHz) Level Level (dB) (dBuV/m) (dB) (dBuV/m) (dBuV) 1 4119.500 39.400 38.729 —34.600 74.000 0.671 PK 2 4961.000 43.100 39.628 —30.900 74.000 3.472 PK 3 5734.500 41.300 36.530 —26.900 68.200 4.770 PK 4 6984.000 44.000 33.493 —24.200 68.200 10.507 PK 5 17974.500 61.703 30.295 —12.297 74.000 31.407 PK 6 * 17974.500 44.799 13.391 —9.201 54.000 31.407 AV Note1: Measure Level (dBuV/m) = Reading Level (dBuV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) NoteZ: The test trace (Frequency range 13GHz ~ 18GHz above average limit) is same as the ambient noise, we selected the highest peak level frequency and performed average emission testing again. FCC ID: Q9DAPINO504505 Page Number: 14 of 18

Report No.: 1906TWO102—U6 Site: ACG1 Time: 2019/06/28 — 03:48 Limit: FCC_Part15.209_RE(3m) Engineer: Kevin Ker Probe: BBHA9120D_1GHz_18GHz Polarity: Horizontal EUT: ACCESS POINT (APINO505) Power: By POE Test Mode: Transmit by 802.11a at channel 5220MHz Ant 0 + 1 90 80| 70 U T m [TU_ LAL [ C1A _TA M UI_LH_I 60 tt~z—$ 50| W. Level(dBuV/m) 4 403 30 20| 10 0 10 1000 10000 18000 Frequency(MHz) No Flag Mark Frequency Measure Reading Margin Limit Factor Type (MHz) Level Level (dB) (dBuV/m) (dB) (dBuV/m) (dBuV) 1 7638.500 47.600 35.742 —26.400 74.000 11.859 PK 2 8242.000 47.200 34.861 —26.800 74.000 12.339 PK 3 8820.000 47.600 34.297 —20.600 68.200 13.303 PK 4 9857.000 49.600 34.810 —18.600 68.200 14.790 PK 5 17957.500 61.931 30.565 —12.069 74.000 31.365 PK 6 * 17957.500 43.747 12.381 —10.253 54.000 31.365 AV Note1: Measure Level (dBuV/m) = Reading Level (dBuV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) NoteZ: The test trace (Frequency range 13GHz ~ 18GHz above average limit) is same as the ambient noise, we selected the highest peak level frequency and performed average emission testing again. FCC ID: Q9DAPINO504505 Page Number: 15 of 18

Report No.: 1906TWO102—U6 Site: ACG1 Time: 2019/06/28 — 03:51 Limit: FCC_Part15.209_RE(3m) Engineer: Kevin Ker Probe: BBHA9120D_1GHz_18GHz Polarity: Vertical EUT: ACCESS POINT (APINO505) Power: By POE Test Mode: Transmit by 802.11a at channel 5220MHz Ant 0 + 1 90 80| af C 60 50| Level(dBuV/m) ®° WM“W 30 20| —10‘ 1000 10000 18000 Frequency(MHz) No Flag Mark Frequency Measure Reading Margin Limit Factor Type (MHz) Level Level (dB) (dBuV/m) (dB) (dBuV/m) (dBuV) 1 9661.500 50.500 36.350 —17.700 68.200 14.151 PK 2 10350.000 49.800 33.413 —18.400 68.200 16.387 PK 3 11701.500 52.000 34.043 —22.000 74.000 17.958 PK 4 15622.500 53.600 32.758 —20.400 74.000 20.842 PK 5 17974.500 61.001 29.593 —12.999 74.000 31.407 PK 6 * 17974.500 43.061 11.653 —10.939 54.000 31.407 AV Note1: Measure Level (dBuV/m) = Reading Level (dBuV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) NoteZ: The test trace (Frequency range 13GHz ~ 18GHz above average limit) is same as the ambient noise, we selected the highest peak level frequency and performed average emission testing again. FCC ID: Q9DAPINO504505 Page Number: 16 of 18

% I‘ Report No.: 1906TWO102—U6 Appendix B — Test Setup Photograph Refer to 1906TWO102—UT" file. FCC ID: Q9DAPINO504505 Page Number: 17 of 18

% I‘ Report No.: 1906TWO102—U6 Appendix C — EUT Photograph Refer to "1906TWO102—UE" file. FCC ID: Q9DAPINO504505 Page Number: 18 of 18


Document Created: 2019-10-24 15:10:58
Document Modified: 2019-10-24 15:10:58
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC