1906TW0102-U4-FCC UNII Test Report (Wi-Fi) Rev3_Part2

FCC ID: Q9DAPIN0504505

Test Report

Download: PDF
FCCID_4474183

Report No.: 1906TW0102-U4 802.11ac-VHT20 6dB Bandwidth - Ant 0 / Ant 0 + 1 Channel 149 (5745MHz) Channel 157 (5785MHz) Channel 165 (5825MHz) 802.11ac-VHT40 6dB Bandwidth - Ant 0 / Ant 0 + 1 Channel 151 (5755MHz) Channel 159 (5795MHz) FCC ID: Q9DAPIN0504505 Page Number: 35 of 426

Report No.: 1906TW0102-U4 802.11ac-VHT80 6dB Bandwidth - Ant 0 / Ant 0 + 1 Channel 155 (5775MHz) FCC ID: Q9DAPIN0504505 Page Number: 36 of 426

Report No.: 1906TW0102-U4 802.11ax-HE20 6dB Bandwidth - Ant 0 / Ant 0 + 1 Channel 149 (5745MHz) Channel 157 (5785MHz) Channel 165 (5825MHz) 802.11ax-HE40 6dB Bandwidth - Ant 0 / Ant 0 + 1 Channel 151 (5755MHz) Channel 159 (5795MHz) FCC ID: Q9DAPIN0504505 Page Number: 37 of 426

Report No.: 1906TW0102-U4 802.11ax-HE80 6dB Bandwidth - Ant 0 / Ant 0 + 1 Channel 155 (5775MHz) FCC ID: Q9DAPIN0504505 Page Number: 38 of 426

Report No.: 1906TW0102-U4 7.4. Output Power Measurement 7.4.1.Test Limit For an indoor access point operating in the band 5.15-5.25 GHz, the maximum conductedoutput power over the frequency band of operation shall not exceed 1 W provided the maximumantenna gain does not exceed 6 dBi. For the band 5.725-5.85 GHz, the maximum conducted output power over the frequency band of operation shall not exceed 1 W (30dBm). If transmitting antennas of directional gain greater than 6dBi are used, the maximumconducted output power shall be reduced by the amount in dB that the directional gain of theantenna exceeds 6dBi. 7.4.2.Test Procedure Used ANSI C63-2013 - Section 12.3 7.4.3.Test Setting Average power measurements were perform only when the EUT was transmitting at its maximum power control level using a broadband power meter with a pulse sensor. The power meter implemented triggering and gating capabilities which were set up such that power measurements were recorded only during the ON time of the transmitter. 7.4.4.Test Setup FCC ID: Q9DAPIN0504505 Page Number: 39 of 426

Report No.: 1906TW0102-U4 7.4.5.Test Result Power output test was verified over all data rates of each mode shown as below table, and then choose the maximum power output (grey marker) for final test of each channel. For Ant 0 / Ant 0 + 1 port of APIN0504 (Antenna M/N: AP-ANT-20W): Test Mode Bandwidth Channel Frequency Data Rate/ Average Power (MHz) MCS (dBm) 6Mbps 18.15 802.11a 20 36 5180 24Mbps 17.72 54Mbps 17.33 MCS0 18.47 802.11ac 20 36 5180 MCS4 17.93 MCS8 17.50 MCS0 15.08 802.11ac 40 38 5190 MCS4 14.77 MCS9 14.32 MCS0 16.95 802.11ac 80 42 5210 MCS4 16.63 MCS9 16.28 MCS0 17.36 802.11ax 20 36 5180 MCS5 16.93 MCS11 16.44 MCS0 17.12 802.11ax 40 38 5190 MCS5 16.91 MCS11 16.54 MCS0 17.08 802.11ax 80 42 5210 MCS5 16.60 MCS11 16.21 FCC ID: Q9DAPIN0504505 Page Number: 40 of 426

Report No.: 1906TW0102-U4 Product ACCESS POINT Temperature 24°C Test Engineer Kevin Ker Relative Humidity 59% 2019/06/26 ~ Test Site SR2 Test Date 2019/07/03 Model No. APIN0504 Test Item Output Power Test Mode Data Channel Freq. Ant 0 Ant 1 Total Average Max Result Rate/ No. (MHz) Average Average Average Power E.I.R.P MCS Power Power Power Limit (dBm) (dBm) (dBm) (dBm) (dBm) 11a 6Mbps 36 5180 18.15 18.05 21.11 ≤ 30.00 Pass 11a 6Mbps 44 5220 18.09 18.26 21.19 ≤ 30.00 Pass 11a 6Mbps 48 5240 18.23 18.21 21.23 ≤ 30.00 Pass 23.42 11a 6Mbps 149 5745 18.35 18.25 21.31 ≤ 30.00 Pass 11a 6Mbps 157 5785 18.42 18.23 21.34 ≤ 30.00 Pass 11a 6Mbps 165 5825 18.45 18.36 21.42 ≤ 30.00 Pass 11ac-VHT20 MCS0 36 5180 18.47 18.29 21.39 ≤ 30.00 Pass 11ac-VHT20 MCS0 44 5220 18.35 18.48 21.43 ≤ 30.00 Pass 11ac-VHT20 MCS0 48 5240 18.44 18.33 21.40 ≤ 30.00 Pass 23.43 11ac-VHT20 MCS0 149 5745 18.44 18.22 21.34 ≤ 30.00 Pass 11ac-VHT20 MCS0 157 5785 18.28 18.38 21.34 ≤ 30.00 Pass 11ac-VHT20 MCS0 165 5825 18.22 18.18 21.21 ≤ 30.00 Pass 11ac-VHT40 MCS0 38 5190 15.08 15.55 18.33 ≤ 30.00 Pass 11ac-VHT40 MCS0 46 5230 17.73 18.42 21.10 ≤ 30.00 Pass 23.22 11ac-VHT40 MCS0 151 5755 18.25 18.16 21.22 ≤ 30.00 Pass 11ac-VHT40 MCS0 159 5795 18.24 18.13 21.20 ≤ 30.00 Pass 11ac-VHT80 MCS0 42 5210 16.95 16.94 19.96 ≤ 30.00 Pass 23.15 11ac-VHT80 MCS0 155 5775 18.24 18.03 21.15 ≤ 30.00 Pass 11ax-HE20 MCS0 36 5180 17.36 17.09 20.24 ≤ 30.00 Pass 11ax-HE20 MCS0 44 5220 18.28 18.32 21.31 ≤ 30.00 Pass 11ax-HE20 MCS0 48 5240 18.32 18.33 21.34 ≤ 30.00 Pass 23.36 11ax-HE20 MCS0 149 5745 18.27 18.22 21.26 ≤ 30.00 Pass 11ax-HE20 MCS0 157 5785 18.24 18.46 21.36 ≤ 30.00 Pass 11ax-HE20 MCS0 165 5825 18.27 18.28 21.29 ≤ 30.00 Pass FCC ID: Q9DAPIN0504505 Page Number: 41 of 426

Report No.: 1906TW0102-U4 Test Mode Data Channel Freq. Ant 0 Ant 1 Total Average Max Result Rate/ No. (MHz) Average Average Average Power E.I.R.P MCS Power Power Power Limit (dBm) (dBm) (dBm) (dBm) (dBm) 11ax-HE40 MCS0 38 5190 17.12 17.20 20.17 ≤ 30.00 Pass 11ax-HE40 MCS0 46 5230 17.67 18.41 21.07 ≤ 30.00 Pass 11ax-HE40 MCS0 151 5755 18.34 18.35 21.36 ≤ 30.00 Pass 23.36 11ax-HE40 MCS0 159 5795 18.22 18.18 21.21 ≤ 30.00 Pass 11ax-HE80 MCS0 42 5210 17.08 16.93 20.02 ≤ 30.00 Pass 11ax-HE80 MCS0 155 5775 18.30 18.06 21.19 ≤ 30.00 Pass Note 1: The Total Average Power (dBm) = 10*log {10(Ant 0 Average Power /10) + 10(Ant 1 Average Power /10) }. Note 2: Average Power Limit (dBm) = 30.00dBm. Note 3: Max E.I.R.P (dBm) = The Max Total Average Power (dBm) + Antenna Gain (dBi), Antenna Gain = 2 dBi. FCC ID: Q9DAPIN0504505 Page Number: 42 of 426

Report No.: 1906TW0102-U4 Product ACCESS POINT Temperature 24°C Test Engineer Kevin Ker Relative Humidity 59% 2019/06/26 ~ Test Site SR2 Test Date 2019/07/03 Model No. APIN0505 Test Item Output Power Test Mode Data Channel Freq. Ant 0 Ant 1 Total Average Max Result Rate/ No. (MHz) Average Average Average Power E.I.R.P MCS Power Power Power Limit (dBm) (dBm) (dBm) (dBm) (dBm) 11a 6Mbps 36 5180 17.05 17.30 20.19 ≤ 30.00 Pass 11a 6Mbps 44 5220 18.21 17.99 21.11 ≤ 30.00 Pass 11a 6Mbps 48 5240 18.28 18.04 21.17 ≤ 30.00 Pass 26.82 11a 6Mbps 149 5745 18.03 18.22 21.14 ≤ 30.00 Pass 11a 6Mbps 157 5785 18.27 18.08 21.19 ≤ 30.00 Pass 11a 6Mbps 165 5825 18.10 18.13 21.13 ≤ 30.00 Pass 11ac-VHT20 MCS0 36 5180 18.03 18.11 21.08 ≤ 30.00 Pass 11ac-VHT20 MCS0 44 5220 18.38 18.10 21.25 ≤ 30.00 Pass 11ac-VHT20 MCS0 48 5240 18.29 18.04 21.18 ≤ 30.00 Pass 27.00 11ac-VHT20 MCS0 149 5745 18.12 18.33 21.24 ≤ 30.00 Pass 11ac-VHT20 MCS0 157 5785 18.29 18.43 21.37 ≤ 30.00 Pass 11ac-VHT20 MCS0 165 5825 18.26 18.18 21.23 ≤ 30.00 Pass 11ac-VHT40 MCS0 38 5190 17.31 17.23 20.28 ≤ 30.00 Pass 11ac-VHT40 MCS0 46 5230 18.35 17.96 21.17 ≤ 30.00 Pass 26.80 11ac-VHT40 MCS0 151 5755 18.04 18.05 21.06 ≤ 30.00 Pass 11ac-VHT40 MCS0 159 5795 18.15 18.14 21.16 ≤ 30.00 Pass 11ac-VHT80 MCS0 42 5210 17.44 17.26 20.36 ≤ 30.00 Pass 26.80 11ac-VHT80 MCS0 155 5775 18.16 18.15 21.17 ≤ 30.00 Pass 11ax-HE20 MCS0 36 5180 18.15 17.74 20.96 ≤ 30.00 Pass 11ax-HE20 MCS0 44 5220 18.31 18.14 21.24 ≤ 30.00 Pass 11ax-HE20 MCS0 48 5240 18.31 18.00 21.17 ≤ 30.00 Pass 26.91 11ax-HE20 MCS0 149 5745 18.25 18.14 21.21 ≤ 30.00 Pass 11ax-HE20 MCS0 157 5785 18.21 18.04 21.14 ≤ 30.00 Pass 11ax-HE20 MCS0 165 5825 18.30 18.24 21.28 ≤ 30.00 Pass FCC ID: Q9DAPIN0504505 Page Number: 43 of 426

Report No.: 1906TW0102-U4 Test Mode Data Channel Freq. Ant 0 Ant 1 Total Average Max Result Rate/ No. (MHz) Average Average Average Power E.I.R.P MCS Power Power Power Limit (dBm) (dBm) (dBm) (dBm) (dBm) 11ax-HE40 MCS0 38 5190 17.95 17.94 20.96 ≤ 30.00 Pass 11ax-HE40 MCS0 46 5230 18.37 17.72 21.07 ≤ 30.00 Pass 26.81 11ax-HE40 MCS0 151 5755 18.09 18.13 21.12 ≤ 30.00 Pass 11ax-HE40 MCS0 159 5795 18.17 18.16 21.18 ≤ 30.00 Pass 11ax-HE80 MCS0 42 5210 17.39 17.36 20.39 ≤ 30.00 Pass 26.74 11ax-HE80 MCS0 155 5775 18.11 18.09 21.11 ≤ 30.00 Pass Note 1: The Total Average Power (dBm) = 10*log {10(Ant 0 Average Power /10) + 10(Ant 1 Average Power /10) }. Note 2: Average Power Limit (dBm) = 30.00dBm. Note 3: Max E.I.R.P (dBm) = The Max Total Average Power (dBm) + Antenna Gain (dBi), Antenna Gain = 5.63 dBi. FCC ID: Q9DAPIN0504505 Page Number: 44 of 426

Report No.: 1906TW0102-U4 7.5. Transmit Power Control 7.5.1.Test Limit The U-NII device is required to have the capability to operate at least 6 dB below the mean EIRP value of 30 dBm. 7.5.2.Test Procedure Used ANSI C63-2013 - Section 12.3 7.5.3.Test Setting Average power measurements were performed only when the EUT was transmitting at its maximum power control level using a broadband power meter with a pulse sensor. The power meter implemented triggering and gating capabilities which were set up such that power measurements were recorded only during the ON time of the transmitter. The trace was averaged over 100 traces to obtain the final measured average power. 7.5.4.Test Setup 7.5.5.Test Result A TPC mechanism is not required for systems operating in frequency band 5150 ~ 5250 MHz & 5725 ~ 5850 MHz. FCC ID: Q9DAPIN0504505 Page Number: 45 of 426

Report No.: 1906TW0102-U4 7.6. Power Spectral Density Measurement 7.6.1.Test Limit For an indoor access point operating in the band 5.15-5.25 GHz, the maximum power spectral density shall not exceed 17 dBm in any 1 megahertz band. For the band 5.725-5.85 GHz, the maximum power spectral density shall not exceed 30 dBm in any 500-kHz band. If transmitting antennas of directional gain greater than 6dBi are used, the peak power spectral density shall be reduced by the amount in dB that the directional gain of theantenna exceeds 6dBi. 7.6.2.Test Procedure Used ANSI C63-2013 - Section 12.6 7.6.3.Test Setting 1. Analyzer was set to the center frequency of the UNII channel under investigation 2. Span was set to encompass the entire 26dB EBW of the signal. 3. RBW = 1MHz, if measurement bandwidth of Maximum PSD is specified in 500 kHz, RBW = 100 kHz 4. VBW = 3MHz 5. Number of sweep points ≥ 2 × (span / RBW) 6. Detector = power averaging (Average) 7. Sweep time = auto 8. Trigger = free run 9. Use the peak search function on the instrument to find the peak of the spectrum and record its value. 10. Add 10*log(1/x), where x is the duty cycle, to the measured power in order to compute the average power during the actual transmission times (because the measurement represents an average over both the on and off times of the transmission). For example, add 10*log(1/0.25) = 6 dB if the duty cycle is 25 percent. 11. When the measurement bandwidth of Maximum PSD is specified in 500 kHz, add a constant factor 10*log(500kHz/100kHz) = 6.99 dB to the measured result. FCC ID: Q9DAPIN0504505 Page Number: 46 of 426

°T Spectrum Analyzer 43 wpuot CG O £ G O A._ —3 EUT

Report No.: 1906TW0102-U4 7.6.5.Test Result Product ACCESS POINT Temperature 24°C Test Engineer Kevin Ker Relative Humidity 59% 2019/06/03 ~ Test Site SR2 Test Date 2019/07/03 Power Spectral Density Model No. APIN0504 Test Item (UNII-Band 1) Test Mode Data Channel Freq. Ant 0 Ant 1 Duty Total PSD Limit Result Rate/ No. (MHz) PSD PSD Cycle PSD (dBm/ MCS (dBm/ (dBm/ (%) (dBm/ MHz) MHz) MHz) MHz) 11a 6Mbps 36 5180 6.26 6.33 94.49 9.31 ≤ 17.00 Pass 11a 6Mbps 44 5220 6.22 6.57 94.49 9.41 ≤ 17.00 Pass 11a 6Mbps 48 5240 6.63 6.60 94.49 9.62 ≤ 17.00 Pass 11ac-VHT20 MCS0 36 5180 7.09 6.77 98.21 9.95 ≤ 17.00 Pass 11ac-VHT20 MCS0 44 5220 6.87 6.86 98.21 9.87 ≤ 17.00 Pass 11ac-VHT20 MCS0 48 5240 6.98 7.15 98.21 10.08 ≤ 17.00 Pass 11ac-VHT40 MCS0 38 5190 1.07 1.62 96.64 4.37 ≤ 17.00 Pass 11ac-VHT40 MCS0 46 5230 3.38 4.31 96.64 6.88 ≤ 17.00 Pass 11ac-VHT80 MCS0 42 5210 -0.71 -0.98 93.70 2.17 ≤ 17.00 Pass 11ax-HE20 MCS0 36 5180 6.10 5.63 97.36 8.88 ≤ 17.00 Pass 11ax-HE20 MCS0 44 5220 6.39 6.50 97.36 9.46 ≤ 17.00 Pass 11ax-HE20 MCS0 48 5240 6.87 6.85 97.36 9.87 ≤ 17.00 Pass 11ax-HE40 MCS0 38 5190 1.92 1.82 94.94 4.88 ≤ 17.00 Pass 11ax-HE40 MCS0 46 5230 3.53 4.13 94.94 6.85 ≤ 17.00 Pass 11ax-HE80 MCS0 42 5210 -0.49 -0.46 91.14 2.53 ≤ 17.00 Pass Note 1: When EUT duty cycle ≥ 98%, the total PSD (dBm/MHz) = 10*log {10(Ant 0 PSD/10) + 10(Ant 1 PSD/10))} (dBm/MHz). Note 2: When EUT duty cycle < 98%, the total PSD (dBm/MHz) = 10*log {10(Ant 0 PSD/10) + 10(Ant 1 PSD/10) } (dBm/MHz) + 10*log (1/Duty Cycle). FCC ID: Q9DAPIN0504505 Page Number: 48 of 426

Report No.: 1906TW0102-U4 Product ACCESS POINT Temperature 22°C Test Engineer Kevin Ker Relative Humidity 54% 2019/06/03 ~ Test Site SR2 Test Date 2019/07/03 Power Spectral Density Model No. APIN0504 Test Item (UNII-Band 3) Test Mode Data Channel Freq. Ant 0 Ant 1 Duty Constant Total Limit Result Rate/ No. (MHz) PSD PSD Cycle Factor PSD (dBm/ MCS (dBm/ (dBm/ (%) (dBm/ 500kHz) 100kHz) 100kHz) 500kHz) 11a 6Mbps 149 5745 -1.50 -1.27 94.49 6.99 8.86 ≤ 30.00 Pass 11a 6Mbps 157 5785 -1.26 -1.34 94.49 6.99 8.95 ≤ 30.00 Pass 11a 6Mbps 165 5825 -1.21 -1.65 94.49 6.99 8.82 ≤ 30.00 Pass 11ac-VHT20 MCS0 149 5745 -0.93 -1.42 98.21 6.99 8.91 ≤ 30.00 Pass 11ac-VHT20 MCS0 157 5785 -1.78 -1.35 98.21 6.99 8.52 ≤ 30.00 Pass 11ac-VHT20 MCS0 165 5825 -1.49 -1.50 98.21 6.99 8.58 ≤ 30.00 Pass 11ac-VHT40 MCS0 151 5755 -4.49 -4.05 96.64 6.99 5.89 ≤ 30.00 Pass 11ac-VHT40 MCS0 159 5795 -4.31 -4.48 96.64 6.99 5.75 ≤ 30.00 Pass 11ac-VHT80 MCS0 155 5775 -7.06 -6.90 93.70 6.99 3.30 ≤ 30.00 Pass 11ax-HE20 MCS0 149 5745 -2.82 -2.71 97.36 6.99 7.35 ≤ 30.00 Pass 11ax-HE20 MCS0 157 5785 -2.37 -2.62 97.36 6.99 7.62 ≤ 30.00 Pass 11ax-HE20 MCS0 165 5825 -2.74 -2.90 97.36 6.99 7.30 ≤ 30.00 Pass 11ax-HE40 MCS0 151 5755 -4.98 -5.38 94.94 6.99 5.05 ≤ 30.00 Pass 11ax-HE40 MCS0 159 5795 -5.45 -5.51 94.94 6.99 4.75 ≤ 30.00 Pass 11ax-HE80 MCS0 155 5775 -7.23 -7.60 91.14 6.99 2.99 ≤ 30.00 Pass Note 1: When EUT duty cycle ≥ 98%, the total PSD (dBm/500KHz) = 10*log {10(Ant 0 PSD/10) + 10(Ant 1 PSD/10)} (dBm/100KHz) + Constant Factor. Note 2: When EUT duty cycle < 98%, the total PSD (dBm/500KHz) = 10*log {10(Ant 0 PSD/10) + 10(Ant 1 PSD/10)} (dBm/100KHz) + Constant Factor + 10*log (1/Duty Cycle). FCC ID: Q9DAPIN0504505 Page Number: 49 of 426

Report No.: 1906TW0102-U4 Product ACCESS POINT Temperature 24°C Test Engineer Kevin Ker Relative Humidity 59% 2019/06/03 ~ Test Site SR2 Test Date 2019/07/03 Power Spectral Density Model No. APIN0505 Test Item (UNII-Band 1) Test Mode Data Channel Freq. Ant 0 Ant 1 Duty Total PSD Limit Result Rate/ No. (MHz) PSD PSD Cycle PSD (dBm/ MCS (dBm/ (dBm/ (%) (dBm/ MHz) MHz) MHz) MHz) 11a 6Mbps 36 5180 5.82 6.06 93.36 8.95 ≤ 14.36 Pass 11a 6Mbps 44 5220 7.80 7.50 93.36 10.66 ≤ 14.36 Pass 11a 6Mbps 48 5240 8.05 7.97 93.36 11.02 ≤ 14.36 Pass 11ac-VHT20 MCS0 36 5180 8.07 8.07 98.21 11.08 ≤ 14.36 Pass 11ac-VHT20 MCS0 44 5220 8.48 8.19 98.21 11.35 ≤ 14.36 Pass 11ac-VHT20 MCS0 48 5240 8.36 8.24 98.21 11.31 ≤ 14.36 Pass 11ac-VHT40 MCS0 38 5190 3.22 2.90 96.40 6.07 ≤ 14.36 Pass 11ac-VHT40 MCS0 46 5230 4.97 4.64 96.40 7.82 ≤ 14.36 Pass 11ac-VHT80 MCS0 42 5210 0.29 0.26 92.83 3.28 ≤ 14.36 Pass 11ax-HE20 MCS0 36 5180 7.08 7.19 97.23 10.15 ≤ 14.36 Pass 11ax-HE20 MCS0 44 5220 7.57 7.41 97.23 10.50 ≤ 14.36 Pass 11ax-HE20 MCS0 48 5240 7.97 7.53 97.23 10.77 ≤ 14.36 Pass 11ax-HE40 MCS0 38 5190 3.22 2.98 95.27 6.11 ≤ 14.36 Pass 11ax-HE40 MCS0 46 5230 4.79 4.38 95.27 7.60 ≤ 14.36 Pass 11ax-HE80 MCS0 42 5210 0.17 0.13 91.17 3.16 ≤ 14.36 Pass Note 1: When EUT duty cycle ≥ 98%, the total PSD (dBm/MHz) = 10*log {10(Ant 0 PSD/10) + 10(Ant 1 PSD/10) } (dBm/MHz). Note 2: When EUT duty cycle < 98%, the total PSD (dBm/MHz) = 10*log {10(Ant 0 PSD/10) + 10(Ant 1 PSD/10)} (dBm/MHz) + 10*log (1/Duty Cycle). Note 3: PSD Limit (dBm/MHz) = 17dBm/MHz - (8.64dBi - 6.00dBi) = 14.36dBm/MHz. FCC ID: Q9DAPIN0504505 Page Number: 50 of 426

Report No.: 1906TW0102-U4 Product ACCESS POINT Temperature 22°C Test Engineer Kevin Ker Relative Humidity 54% 2019/07/01 ~ Test Site SR2 Test Date 2019/07/03 Power Spectral Density Model No. APIN0505 Test Item (UNII-Band 3) Test Mode Data Channel Freq. Ant 0 Ant 1 Duty Constant Total Limit Result Rate/ No. (MHz) PSD PSD Cycle Factor PSD (dBm/ MCS (dBm/ (dBm/ (%) (dBm/ 500kHz) 100kHz) 100kHz) 500kHz) 11a 6Mbps 149 5745 -0.42 -0.44 93.36 6.99 2.58 ≤ 27.36 Pass 11a 6Mbps 157 5785 -1.02 -0.21 93.36 6.99 2.42 ≤ 27.36 Pass 11a 6Mbps 165 5825 -0.82 -0.26 93.36 6.99 2.48 ≤ 27.36 Pass 11ac-VHT20 MCS0 149 5745 -0.26 -0.83 98.21 6.99 2.48 ≤ 27.36 Pass 11ac-VHT20 MCS0 157 5785 -0.32 -0.53 98.21 6.99 2.58 ≤ 27.36 Pass 11ac-VHT20 MCS0 165 5825 -0.50 -0.33 98.21 6.99 2.60 ≤ 27.36 Pass 11ac-VHT40 MCS0 151 5755 -3.62 -3.45 96.40 6.99 -0.52 ≤ 27.36 Pass 11ac-VHT40 MCS0 159 5795 -3.46 -3.24 96.40 6.99 -0.33 ≤ 27.36 Pass 11ac-VHT80 MCS0 155 5775 -5.42 -5.90 92.83 6.99 -2.64 ≤ 27.36 Pass 11ax-HE20 MCS0 149 5745 -2.03 -1.71 97.23 6.99 1.14 ≤ 27.36 Pass 11ax-HE20 MCS0 157 5785 -1.41 -1.93 97.23 6.99 1.35 ≤ 27.36 Pass 11ax-HE20 MCS0 165 5825 -2.05 -1.47 97.23 6.99 1.26 ≤ 27.36 Pass 11ax-HE40 MCS0 151 5755 -4.49 -4.85 95.27 6.99 -1.66 ≤ 27.36 Pass 11ax-HE40 MCS0 159 5795 -4.34 -4.58 95.27 6.99 -1.45 ≤ 27.36 Pass 11ax-HE80 MCS0 155 5775 -6.61 -7.33 91.17 6.99 -3.95 ≤ 27.36 Pass Note 1: When EUT duty cycle ≥ 98%, the total PSD (dBm/500KHz) = 10*log {10(Ant 0 PSD/10) + 10(Ant 1 PSD/10)} (dBm/100KHz) + Constant Factor. Note 2: When EUT duty cycle < 98%, the total PSD (dBm/500KHz) = 10*log {10(Ant 0 PSD/10) + 10(Ant 1 PSD/10)} (dBm/100KHz) + Constant Factor + 10*log (1/Duty Cycle). Note 3: PSD Limit (dBm/500kHz) = 30dBm/500kHz - (8.64dBi - 6dBi) = 27.36dBm/500kHz. FCC ID: Q9DAPIN0504505 Page Number: 51 of 426

Report No.: 1906TW0102-U4 Product ACCESS POINT Temperature 22°C 2019/06/03 ~ Test Engineer Kevin Ker Test Date 2019/07/03 Model No. APIN0504 802.11a Power Spectral Density - Ant 0 / Ant 0 + 1 Channel 36 (5180MHz) Channel 44 (5220MHz) Channel 48 (5240MHz) Channel 149 (5745MHz) FCC ID: Q9DAPIN0504505 Page Number: 52 of 426

Report No.: 1906TW0102-U4 Channel 157 (5785MHz) Channel 165 (5825MHz) FCC ID: Q9DAPIN0504505 Page Number: 53 of 426

Report No.: 1906TW0102-U4 802.11ac-VHT20 Power Spectral Density - Ant 0 / Ant 0 + 1 Channel 36 (5180MHz) Channel 44 (5220MHz) Channel 48 (5240MHz) Channel 149 (5745MHz) Channel 157 (5785MHz) Channel 165 (5825MHz) FCC ID: Q9DAPIN0504505 Page Number: 54 of 426

Report No.: 1906TW0102-U4 802.11ac-VHT40 Power Spectral Density - Ant 0 / Ant 0 + 1 Channel 38 (5190MHz) Channel 46 (5230MHz) Channel 151 (5755MHz) Channel 159 (5795MHz) 802.11ac-VHT80 Power Spectral Density - Ant 0 / Ant 0 + 1 Channel 42 (5210MHz) Channel 155 (5775MHz) FCC ID: Q9DAPIN0504505 Page Number: 55 of 426

Report No.: 1906TW0102-U4 802.11ax-HE20 Power Spectral Density - Ant 0 / Ant 0 + 1 Channel 36 (5180MHz) Channel 44 (5220MHz) Channel 48 (5240MHz) Channel 149 (5745MHz) Channel 157 (5785MHz) Channel 165 (5825MHz) FCC ID: Q9DAPIN0504505 Page Number: 56 of 426

Report No.: 1906TW0102-U4 802.11ax-HE40 Power Spectral Density - Ant 0 / Ant 0 + 1 Channel 38 (5190MHz) Channel 46 (5230MHz) Channel 151 (5755MHz) Channel 159 (5795MHz) 802.11ax-HE80 Power Spectral Density - Ant 0 / Ant 0 + 1 Channel 42 (5210MHz) Channel 155 (5775MHz) FCC ID: Q9DAPIN0504505 Page Number: 57 of 426

Report No.: 1906TW0102-U4 802.11a Power Spectral Density - Ant 1 / Ant 0 + 1 Channel 36 (5180MHz) Channel 44 (5220MHz) Channel 48 (5240MHz) Channel 149 (5745MHz) Channel 157 (5785MHz) Channel 165 (5825MHz) FCC ID: Q9DAPIN0504505 Page Number: 58 of 426

Report No.: 1906TW0102-U4 802.11ac-VHT20 Power Spectral Density - Ant 1 / Ant 0 + 1 Channel 36 (5180MHz) Channel 44 (5220MHz) Channel 48 (5240MHz) Channel 149 (5745MHz) Channel 157 (5785MHz) Channel 165 (5825MHz) FCC ID: Q9DAPIN0504505 Page Number: 59 of 426

Report No.: 1906TW0102-U4 802.11ac-VHT40 Power Spectral Density - Ant 1 / Ant 0 + 1 Channel 38 (5190MHz) Channel 46 (5230MHz) Channel 151 (5755MHz) Channel 159 (5795MHz) 802.11ac-VHT80 Power Spectral Density - Ant 1 / Ant 0 + 1 Channel 42 (5210MHz) Channel 155 (5775MHz) FCC ID: Q9DAPIN0504505 Page Number: 60 of 426


Document Created: 2019-10-03 12:53:08
Document Modified: 2019-10-03 12:53:08
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC