1906TW0102-U4-FCC UNII Test Report (Wi-Fi) Rev3_Part1

FCC ID: Q9DAPIN0504505

Test Report

Download: PDF
FCCID_4474182

MRT Technology (Taiwan) Co., Ltd Report No.: 1906TW0102-U4 Phone: +886-3-3288388 Report Version: V03 Web: www.mrt-cert.com Issue Date: 10-03-2019 MEASUREMENT REPORT FCC PART 15.407 WLAN 802.11a/n/ac/ax FCC ID: Q9DAPIN0504505 APPLICANT: Hewlett Packard Enterprise Company Application Type: Certification Product: ACCESS POINT Model No.: APIN0504, APIN0505 Brand Name: , FCC Classification: Unlicensed National Information Infrastructure (NII) FCC Rule Part(s): Part15 Subpart E (Section 15.407) Test Procedure(s): ANSI C63.10-2013, KDB 789033 D02v02r01, KDB 662911 D01v02r01 Test Date: June 03 ~ July 14, 2019 Reviewed By: (Paddy Chen) Approved By: (Chenz Ker) The test results relate only to the samples tested. This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in ANSI C63.10-2013. Test results reported herein relate only to the item(s) tested. The test report shall not be reproduced except in full without the written approval of MRT Technology (Taiwan) Co., Ltd. FCC ID: Q9DAPIN0504505 Page Number: 1 of 426

Report No.: 1906TW0102-U4 Revision History Report No. Version Description Issue Date Note 1906TW0102-U4 Rev. 01 Initial report 07-15-2019 Invalid 1906TW0102-U4 Rev. 02 Update antenna port plot 10-01-2019 Invalid Update frequency stability 1906TW0102-U4 Rev. 03 10-03-2019 Valid test procedure FCC ID: Q9DAPIN0504505 Page Number: 2 of 426

Report No.: 1906TW0102-U4 CONTENTS Description Page §2.1033General Information .......................................................................................................... 6 1. INTRODUCTION ..................................................................................................................... 7 1.1. Scope ........................................................................................................................... 7 1.2. MRT Test Location ....................................................................................................... 7 2. PRODUCT INFORMATION ..................................................................................................... 8 2.1. Equipment Description.................................................................................................. 8 2.2. Product Specification Subjective to this Report ............................................................. 8 2.3. Working Frequencies for this report .............................................................................. 9 2.4. Description of Available Antennas ............................................................................... 10 2.5. Description of Antenna RF Port .................................................................................. 12 2.6. Test Mode .................................................................................................................. 13 2.7. Description of Test Software ....................................................................................... 13 2.8. Device Capabilities ..................................................................................................... 14 2.9. EMI Suppression Device(s)/Modifications ................................................................... 17 2.10. Labeling Requirements ............................................................................................... 17 3. DESCRIPTION OF TEST ...................................................................................................... 18 3.1. Evaluation Procedure ................................................................................................. 18 3.2. AC Line Conducted Emissions ................................................................................... 18 3.3. Radiated Emissions .................................................................................................... 19 4. ANTENNA REQUIREMENTS ................................................................................................ 20 5. TEST EQUIPMENT CALIBRATION DATE ............................................................................ 21 6. MEASUREMENT UNCERTAINTY ......................................................................................... 22 7. TEST RESULT ...................................................................................................................... 23 7.1. Summary .................................................................................................................... 23 7.2. 26dB Bandwidth Measurement ................................................................................... 24 7.2.1. Test Limit .................................................................................................................... 24 7.2.2. Test Procedure used ................................................................................................... 24 7.2.3. Test Setting ................................................................................................................. 24 7.2.4. Test Setup .................................................................................................................. 24 7.2.5. Test Result .................................................................................................................. 25 7.3. 6dB Bandwidth Measurement ..................................................................................... 32 7.3.1. Test Limit .................................................................................................................... 32 7.3.2. Test Procedure used ................................................................................................... 32 FCC ID: Q9DAPIN0504505 Page Number: 3 of 426

Report No.: 1906TW0102-U4 7.3.3. Test Setting ................................................................................................................. 32 7.3.4. Test Setup .................................................................................................................. 32 7.3.5. Test Result .................................................................................................................. 33 7.4. Output Power Measurement ....................................................................................... 39 7.4.1. Test Limit .................................................................................................................... 39 7.4.2. Test Procedure Used .................................................................................................. 39 7.4.3. Test Setting ................................................................................................................. 39 7.4.4. Test Setup .................................................................................................................. 39 7.4.5. Test Result .................................................................................................................. 40 7.5. Transmit Power Control .............................................................................................. 45 7.5.1. Test Limit .................................................................................................................... 45 7.5.2. Test Procedure Used .................................................................................................. 45 7.5.3. Test Setting ................................................................................................................. 45 7.5.4. Test Setup .................................................................................................................. 45 7.5.5. Test Result .................................................................................................................. 45 7.6. Power Spectral Density Measurement ........................................................................ 46 7.6.1. Test Limit .................................................................................................................... 46 7.6.2. Test Procedure Used .................................................................................................. 46 7.6.3. Test Setting ................................................................................................................. 46 7.6.4. Test Setup .................................................................................................................. 47 7.6.5. Test Result .................................................................................................................. 48 7.7. Frequency Stability Measurement............................................................................... 73 7.7.1. Test Limit .................................................................................................................... 73 7.7.2. Test Procedure Used .................................................................................................. 73 7.7.3. Test Setup .................................................................................................................. 74 7.7.4. Test Result .................................................................................................................. 75 7.8. Radiated Spurious Emission Measurement ................................................................ 76 7.8.1. Test Limit .................................................................................................................... 76 7.8.2. Test Procedure Used .................................................................................................. 76 7.8.3. Test Setting ................................................................................................................. 76 7.8.4. Test Setup .................................................................................................................. 78 7.8.5. Test Result .................................................................................................................. 79 7.9. Radiated Restricted Band Edge Measurement ......................................................... 207 7.9.1. Test Limit .................................................................................................................. 207 7.9.2. Test Procedure Used ................................................................................................ 208 7.9.3. Test Setting ............................................................................................................... 208 7.9.4. Test Setup ................................................................................................................ 209 7.9.5. Test Result ................................................................................................................ 210 7.10. AC Conducted Emissions Measurement................................................................... 418 FCC ID: Q9DAPIN0504505 Page Number: 4 of 426

Report No.: 1906TW0102-U4 7.10.1. Test Limit .................................................................................................................. 418 7.10.2. Test Procedure ......................................................................................................... 418 7.10.3. Test Setup ................................................................................................................ 419 7.10.4. Test Result ................................................................................................................ 420 8. CONCLUSION..................................................................................................................... 424 Appendix A - Test Setup Photograph ....................................................................................... 425 Appendix B - EUT Photograph .................................................................................................. 426 FCC ID: Q9DAPIN0504505 Page Number: 5 of 426

Report No.: 1906TW0102-U4 §2.1033General Information Applicant: Hewlett Packard Enterprise Company Applicant Address: 3333 Scott Blvd, Santa Clara, CA 94089, USA Manufacturer: Hewlett Packard Enterprise Company Manufacturer Address: 3333 Scott Blvd, Santa Clara, CA 94089, USA Test Site: MRT Technology (Taiwan) Co., Ltd Test Site Address: No. 38, Fuxing Second Rd., Guishan Dist., Taoyuan City 333, Taiwan (R.O.C) APIN0504: Conducted Sample S/N: DB196B0112 Radiated Sample S/N: DB196B0122 Test Device Serial No.: APIN0505: Conducted Sample S/N: DB195B013F Radiated Sample S/N: DB196B0029 Test Facility / Accreditations Measurements were performed at MRT Laboratory located in Fuxing Rd., Taoyuan, Taiwan ( R.O.C ) MRT facility is a FCC registered (Reg. No. 153292) test facility with the site description report on file and is designated by the FCC as an Accredited Test Film.  MRT facility is an IC registered (MRT Reg. No. 21723-1) test laboratory with the site description on file at Industry Canada.  MRT Lab is accredited to ISO 17025 by the American Association for Laboratory Accreditation (TAF) under the American Association for Laboratory Accreditation Program (TAF Cert. No. 3261) in EMC, Telecommunications and Radio testing for FCC, Industry Taiwan, EU and TELEC Rules. FCC ID: Q9DAPIN0504505 Page Number: 6 of 426

Report No.: 1906TW0102-U4 1. INTRODUCTION 1.1. Scope Measurement and determination of electromagnetic emissions (EMC) of radio frequency devices includingintentional and/or unintentional radiators for compliance with the technical rules and regulations of the FederalCommunications Commission and the Innovation, Science and Economic Development Canada and Certification and Engineering Bureau. 1.2. MRT Test Location The map below shows the location of the MRT LABORATORY, its proximity to the Taoyuan City. These measurement tests were conducted at the MRT Technology (Taiwan) Co., Ltd. Facility located at No.38, Fuxing 2nd Rd., Guishan Dist., Taoyuan City 33377, Taiwan (R.O.C). FCC ID: Q9DAPIN0504505 Page Number: 7 of 426

Report No.: 1906TW0102-U4 2. PRODUCT INFORMATION 2.1. Equipment Description Product Name: ACCESS POINT Model No.: APIN0504, APIN0505 Brand Name: , Wi-Fi Specification: 802.11a/b/g/n/ac/ax Bluetooth Specification: v4.2 single mode Zigbee Specification: 802.15.4 Software Version: 6.2.1A1 bring up F.100 Operating Temperature: 0 ~ 50 °C Power Type: AC Adapter or POE input Operating Environment: Indoor Use Note: The difference between models is that EUT use different antenna and appearance, APIN0504 use some external antennas, but APIN0505 use internal antenna, other hardware and software are the same. Besides, each model has its own power parameter value. 2.2. Product Specification Subjective to this Report Frequency Range: For 802.11a/n-HT20/ac-VHT20/ax-HE20: 5180~5240MHz, 5745~5825MHz For 802.11n-HT40/ac-VHT40/ax-HE40: 5190~5230MHz, 5755~5795MHz For 802.11ac-VHT80/ax-HE80: 5210MHz, 5775MHz Type of Modulation: 802.11a/n/ac: OFDM 802.11ax: OFDMA Data Rate: 802.11a: 6/9/12/18/24/36/48/54Mbps 802.11n: up to 300Mbps 802.11ac: up to 866.6Mbps 802.11ax: up to 2402Mbps Note: For other features of this EUT, test report will be issued separately. FCC ID: Q9DAPIN0504505 Page Number: 8 of 426

Report No.: 1906TW0102-U4 2.3. Working Frequencies for this report 802.11a/n-HT20/ac-VHT20/ax-HE20 Channel Frequency Channel Frequency Channel Frequency 36 5180 MHz 40 5200 MHz 44 5220 MHz 48 5240 MHz 149 5745 MHz 153 5765 MHz 157 5785 MHz 161 5805 MHz 165 5825 MHz 802.11n-HT40/ac-VHT40/ax-HE40 Channel Frequency Channel Frequency Channel Frequency 38 5190 MHz 46 5230 MHz 151 5755 MHz 159 5795 MHz -- -- -- -- 802.11ac-VHT80/ax-HE80 Channel Frequency Channel Frequency Channel Frequency 42 5210 MHz 155 5775 MHz -- -- FCC ID: Q9DAPIN0504505 Page Number: 9 of 426

Report No.: 1906TW0102-U4 2.4. Description of Available Antennas APIN0504 Antenna Directionality Frequency Model No. Max Peak BF Dir CDD Dir Gain No. Band Gain Gain (dBi) (GHz) (dBi) (dBi) For Power For PSD Wi-Fi External Antenna List (2.4GHz 2*2 MIMO, 5GHz 2*2 MIMO) 2.4 3.8 6.81 3.8 6.81 1 Omni AP-ANT-1W 5 5.8 8.81 5.8 8.81 2.4 2.3 5.31 2.3 5.31 2 Omni AP-ANT-13B 5 4.0 7.01 4.0 7.01 2.4 3.0 6.01 3.0 6.01 3 Omni AP-ANT-19 5 6.0 9.01 6.0 9.01 2.4 2.0 5.01 2.0 5.01 4 Omni AP-ANT-20W 5 2.0 5.01 2.0 5.01 2.4 4.0 7.01 4.0 7.01 5 Omni AP-ANT-40 5 5.0 8.01 5.0 8.01 2.4 5.0 5.0 5.0 8.01 6 (Note 3) Directional AP-ANT-25A 5 5.0 5.0 5.0 8.01 2.4 7.5 7.5 7.5 10.51 7 (Note 3) Directional AP-ANT-28 5 7.5 7.5 7.5 10.51 Bluetooth & ZigBee Internal Antenna PCB 2.4 3.3 APIN0505 Directionality Frequency Band Max BF Dir Gain CDD Dir Gain (GHz) Peak Gain (dBi) (dBi) (dBi) For Power For PSD Wi-Fi Internal Antenna List (2.4GHz 2*2 MIMO, 5GHz 4*4 MIMO) Omni 2.4 4.29 7.08 4.29 7.08 Omni 5 5.63 8.64 5.63 8.64 Bluetooth & ZigBee Internal Antenna PCB 2.4 3.3 FCC ID: Q9DAPIN0504505 Page Number: 10 of 426

Report No.: 1906TW0102-U4 Note: 1. The EUT supports Cyclic Delay Diversity (CDD) mode, and CDD signals are correlated. For CDD transmissions, directional gain is calculated as follows, NANT = 2, NSS = 1. If all antennas have the same gain, GANT, Directional gain = GANT + Array Gain, where Array Gain is as follows. • For power spectral density (PSD) measurements on all devices, Array Gain = 10 log (NANT/ NSS) dB = 3.01; • For power measurements on IEEE 802.11 devices, Array Gain = 0 dB for NANT ≤ 4; 2. The EUT also supports Beam Forming mode, and the Beam Forming support 802.11n/ac/ax, not include 802.11a/b/g. Directional gain = GANT + Array Gain, BF Gain was declared by the applicant. 3. Two type antennas are cross polarized, the detail refer to antenna specification. 4. For APIN0504, low gain antenna AP-ANT-20W was selected to perform all RF testing that can got maximum power setting. High gain Omni antenna AP-ANT-19 & AP-ANT-40 and directional antenna AP-ANT-28 were selected to perform radiated spurious emission and band edge testing. High gain antenna power setting will be reduced according to difference value of antenna gain declared by applicant. 5. For APIN0505, its directional gain was declared by the applicant, the detail refers to antenna specification. FCC ID: Q9DAPIN0504505 Page Number: 11 of 426

Report No.: 1906TW0102-U4 2.5. Description of Antenna RF Port Antenna RF Port -- 2.4GHz RF Port 5GHz RF Port Software Control Port Ant 0 Ant 1 Ant 0 Ant 1 APIN0504 APIN0505 FCC ID: Q9DAPIN0504505 Page Number: 12 of 426

Report No.: 1906TW0102-U4 2.6. Test Mode Test Mode Mode 1: Transmit by 802.11a (6Mbps) Mode 2: Transmit by 802.11ac-VHT20 (MCS0) Mode 3: Transmit by 802.11ac-VHT40 (MCS0) Mode 4: Transmit by 802.11ac-VHT80 (MCS0) Mode 5: Transmit by 802.11ax-HE20 (MCS0) Mode 6: Transmit by 802.11ax-HE40 (MCS0) Mode 7: Transmit by 802.11ax-HE80 (MCS0) 2.7. Description of Test Software The test utility software used during testing was “accessMTool”, and the version was “v3.0.0.7”. Detail power setting refer to operation description. FCC ID: Q9DAPIN0504505 Page Number: 13 of 426

Report No.: 1906TW0102-U4 2.8. Device Capabilities This device contains the following capabilities: 802.11a/b/g/n/ac/ax Wi-Fi and Bluetooth v4.2 single mode and Zigbee devices Note: 5GHz (NII) operation is possible in 20MHz, 40MHz and 80MHz channel bandwidths. The maximum achievable duty cycles for all modes were determined based on measurements performed on a spectrum analyzer in zero-span mode with RBW = 8MHz, VBW = 50MHz per the guidance of Section B)2)b) of KDB 789033 D02v02r01. The RBW and VBW were both greater than 50/T, where T is the minimum transmission duration, and the number of sweep points across T was greater than 100. The duty cycles are as follows: Model No. Test Mode Duty Cycle 802.11a 94.49% 802.11ac-VHT20 98.21% 802.11ac-VHT40 96.64% APIN0504 802.11ac-VHT80 93.70% 802.11ax-HE20 97.36% 802.11ax-HE40 94.94% 802.11ax-HE80 91.14% 802.11a 93.36% 802.11ac-VHT20 98.21% 802.11ac-VHT40 96.40% APIN0505 802.11ac-VHT80 92.83% 802.11ax-HE20 97.23% 802.11ax-HE40 95.27% 802.11ax-HE80 91.17% Duty Cycle (T = Transmission Duration) - APIN0504 802.11a (T = 2.057ms) 802.11ac-VHT20 (T = 1.915ms) FCC ID: Q9DAPIN0504505 Page Number: 14 of 426

Report No.: 1906TW0102-U4 802.11ac-VHT40 (T = 947.5us) 802.11ac-VHT80 (T = 456.9us) 802.11ax-HE20 (T = 1.475ms) 802.11ax-HE40 (T = 762.5us) 802.11ax-HE80 (T = 394.1us) FCC ID: Q9DAPIN0504505 Page Number: 15 of 426

Report No.: 1906TW0102-U4 Duty Cycle (T = Transmission Duration) - APIN0505 802.11a (T = 2.040ms) 802.11ac-VHT20 (T = 1.920ms) 802.11ac-VHT40 (T = 947.5us) 802.11ac-VHT80 (T = 456.9us) 802.11ax-HE20 (T = 1.474ms) 802.11ax-HE40 (T = 765.1us) FCC ID: Q9DAPIN0504505 Page Number: 16 of 426

Report No.: 1906TW0102-U4 802.11ax-HE80 (T = 400.0us) 2.9. EMI Suppression Device(s)/Modifications No EMI suppression device(s) were added and/or no modifications were made during testing. 2.10. Labeling Requirements Per 2.1074 & 15.19; Docket 95-19 The label shall be permanently affixed at a conspicuous location on the device; instruction manual or pamphletsupplied to the user and be readily visible to the purchaser at the time of purchase. However, when the deviceis so small wherein placement of the label with specified statement is not practical, only the FCC ID must be displayed on the device per Section 15.19(a)(5). Please see attachment for FCC ID label andlabel location. FCC ID: Q9DAPIN0504505 Page Number: 17 of 426

Report No.: 1906TW0102-U4 3. DESCRIPTION OF TEST 3.1. Evaluation Procedure The measurement procedures described in the American National Standard for Testing Unlicensed WirelessDevices (ANSI C63.10-2013), and the guidance provided in KDB 789033 D02v02r01 were used in themeasurement. Deviation from measurement procedure…………………………….....................................None 3.2. AC Line Conducted Emissions The line-conducted facility is located inside an8'x4'x4' shielded enclosure. A 1m x 2m wooden table 80cm high is placed 40cm away from the vertical wall and 80cm away from the sidewall of the shielded room. Two 10kHz-30MHz, 50Ω/50uH Line-Impedance Stabilization Networks (LISNs) are bonded to the shielded room floor. Power to the LISNs is filtered by external high-current high-insertion loss power line filters. These filters attenuate ambient signal noise from entering the measurement lines. These filters are also bonded to the shielded enclosure. The EUT is powered from one LISN and the support equipment is powered from the second LISN. All interconnecting cables more than 1 meter were shortened to a 1 meter length by non-inductive bundling (serpentine fashion) and draped over the back edge of the test table. All cables were at least 40cm above the horizontal reference ground-plane. Power cables for support equipment were routed down to the second LISN while ensuring that that cables were not draped over the second LISN. Sufficient time for the EUT, support equipment, and test equipment was allowed in order for them to warm up to their normal operating condition. The RF output of the LISN was connected to the receiver and exploratory measurements were made to determine the frequencies producing the maximum emission from the EUT. The receiver was scanned from 150kHz to 30MHz. The detector function was set to peak mode for exploratory measurements while the bandwidth of the analyzer was set to 9kHz. The EUT, support equipment, and interconnecting cables were arranged and manipulated to maximize each emission. Each emission was also maximized by varying: power lines, the mode of operation or data exchange speed, or support equipment whichever determined the worst-case emission. Once the worst case emissions have been identified, the one EUT cable configuration/arrangement and mode of operation that produced these emissions are used for final measurements on the same test site. The analyzer is set to CISPR quasi-peak and average detectors with a 9kHz resolution bandwidth for final measurements. An extension cord was used to connect to a single LISN which powered by EUT. The extension cord was calibrated with LISN, the impedance and insertion loss are compliance with the requirements as stated in ANSI C63.10-2013. FCC ID: Q9DAPIN0504505 Page Number: 18 of 426

Report No.: 1906TW0102-U4 3.3. Radiated Emissions The radiated test facilities consisted of an indoor 3 meter semi-anechoic chamber used for final measurements and exploratory measurements, when necessary. The measurement area is contained within the semi-anechoic chamber which is shielded from any ambient interference. For measurements above 1GHz absorbers are arranged on the floor between the turn table and the antenna mast in such a way so as to maximize the reduction of reflections. For measurements below 1GHz, the absorbers are removed. A MF Model 210SS turntable is used for radiated measurement. It is a continuously rotatable, remotecontrolled, metallic turntable and 2 meters (6.56 ft.) in diameter. The turn table is flush with the raised floor of the chamber in order to maintain its function as a ground plane. An80cm high PVC support structure is placed on top of the turntable. For all measurements, the spectrum was scanned through all EUT azimuths and from 1 to 4 meter receive antenna height using a broadband antenna from 30MHz up to the upper frequency shown in 15.33(b)(1) depending on the highest frequency generated or used in the device or on which the device operates or tunes. For frequencies above 1GHz, linearly polarized double ridge horn antennas were used. For frequencies below 30MHz, a calibrated loop antenna was used. When exploratory measurements were necessary, they were performed at 1 meter test distance inside the semi-anechoic chamber using broadband antennas, broadband amplifiers, and spectrum analyzers to determine the frequencies and modes producing the maximum emissions. Sufficient time for the EUT, support equipment, and test equipment was allowed in order for them to warm up to their normal operating condition. The test set-up for frequencies below 1GHz was placed on top of the 0.8 meter high, 1 x 1.5 meter table; and test set-up for frequencies 1-40GHz was placed on top of the 1.5 meter high, 1 x 1.5 meter table. The EUT, support equipment, and interconnecting cables were arranged and manipulated tomaximize each emission. Appropriate precaution was taken to ensure that all emissions from the EUT were maximized and investigated. The system configuration, clock speed, mode of operation or video resolution, if applicable, turntable azimuth, and receive antenna height was noted for each frequency found. Final measurements were made in the semi-anechoic chamber using calibrated, linearly polarized broadband and horn antennas. The test setup was configured to the setup that produced the worst case emissions. The spectrum analyzer was set to investigate all frequencies required for testing to compare the highest radiated disturbances with respect to the specified limits. The turntable containing the EUT was rotated through 360 degrees and the height of the receive antenna was varied 1 to 4 meters and stopped at the azimuth and height producing the maximum emission. Each emission was maximized by changing the orientation of the EUT through three orthogonal planes and changing the polarity of the receive antenna, whichever produced the worst-case emissions. According to 3dB Beam-Width of horn antenna, the horn antenna should be always directed to the EUT when rising height. FCC ID: Q9DAPIN0504505 Page Number: 19 of 426

Report No.: 1906TW0102-U4 4. ANTENNA REQUIREMENTS Excerpt from §15.203 of the FCC Rules/Regulations: “An intentional radiator antenna shall be designed to ensure that no antenna other than that furnished by theresponsible party can be used with the device. The use of a permanently attached antenna or of an antennathat uses a unique coupling to the intentional radiator shall be considered sufficient to comply with theprovisions of this section.” For APIN0505 ⚫ The antenna of the ACCESS POINT is permanently attached. ⚫ There are no provisions for connection to an external antenna. For APIN0504 ⚫ The antenna of the ACCESS POINT uses a reversed SMA connector. Conclusion: The unit complies with the requirement of §15.203. FCC ID: Q9DAPIN0504505 Page Number: 20 of 426

Report No.: 1906TW0102-U4 5. TEST EQUIPMENT CALIBRATION DATE Conducted Emissions Instrument Manufacturer Type No. Asset No. Cali. Interval Cali. Due Date Two-Line V-Network R&S ENV 216 MRTTWA00019 1 year 2020/03/25 Two-Line V-Network R&S ENV 216 MRTTWA00020 1 year 2020/04/25 8-Wire ISN (T8) R&S ENY81 MRTTWA00018 1 year 2020/04/23 EMI Test Receiver R&S ESR3 MRTTWA00045 1 year 2020/05/29 Temperature/Humidity Meter TFA 35.1078.10.IT MRTTWA00033 1 year 2020/05/30 Radiated Emissions Instrument Manufacturer Type No. Asset No. Cali. Interval Cali. Due Date Acitve Loop Antenna SCHWARZBECK FMZB 1519B MRTTWA00002 1 year 2020/04/29 Broadband TRILOG Antenna SCHWARZBECK VULB 9162 MRTTWA00001 1 year 2020/06/04 Broadband Horn antenna SCHWARZBECK BBHA 9120D MRTTWA00003 1 year 2020/04/22 Breitband Horn antenna SCHWARZBECK BBHA 9170 MRTTWA00004 1 year 2020/04/23 Broadband Preamplifier SCHWARZBECK BBV 9718 MRTTWA00005 1 year 2020/04/24 Broadband Amplifier SCHWARZBECK BBV 9721 MRTTWA00006 1 year 2020/04/24 Signal Analyzer R&S FSV40 MRTTWA00007 1 year 2020/03/26 EMI Test Receiver R&S ESR3 MRTTWA00009 1 year 2020/03/25 EXA Signal Analyzer KEYSIGHT N9010A MRTTWA00012 1 year 2019/10/30 Antenna Cable HUBERSUHNER SF106 MRTTWE00010 1 year 2020/04/22 Temperature/Humidity Meter TFA 35.1078.10.IT MRTTWA00032 1 year 2020/05/30 Conducted Test Equipment Instrument Manufacturer Type No. Asset No. Cali. Interval Cali. Due Date X-Series USB Peak and KEYSIGHT U2021XA MRTTWA00014 1 year 2020/04/22 Average Power Sensor Wideband Radio R&S CMW 500 MRTTWA00041 1 year 2020/01/28 Communication Taster EXA Signal Analyzer KEYSIGHT N9010A MRTTWA00012 1 year 2019/10/30 EXA Signal Analyzer KEYSIGHT N9010B MRTTWA00074 1 year 2020/07/11 Signal Analyzer R&S FSV40 MRTTWA00007 1 year 2020/03/26 Temperature/Humidity Meter TFA 35.1078.10.IT MRTTWA00033 1 year 2020/05/30 Software Version Function e3 9.160520a EMI Test Software FCC ID: Q9DAPIN0504505 Page Number: 21 of 426

Report No.: 1906TW0102-U4 6. MEASUREMENT UNCERTAINTY Where relevant, the following test uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16-4-2. This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k = 2. AC Conducted Emission Measurement Measuring Uncertainty for a Level of Confidence of 95% (U=2Uc(y)): 150kHz~30MHz: 2.53dB Radiated Emission Measurement Measuring Uncertainty for a Level of Confidence of 95% (U=2Uc(y)): 9kHz ~ 1GHz: 4.25dB 1GHz ~ 40GHz: 4.45dB FCC ID: Q9DAPIN0504505 Page Number: 22 of 426

Report No.: 1906TW0102-U4 7. TEST RESULT 7.1. Summary FCC Test Description Test Limit Test Test Reference Section(s) Condition Result 15.407(a) 26dB Bandwidth N/A Pass Section 7.2 15.407(e) 6dB Bandwidth ≥ 500kHz Pass Section 7.3 15.407(a)(1)(ii), Maximum Conducted ≤ 30 dBm Pass Section 7.4 (3) Output Power Conducted 15.407(h)(1) Transmit Power Control ≤ 24 dBm N/A Section 7.5 15.407(a)(1)(ii), Peak Power Spectral ≤ 17 dBm/MHz UNII-1 Pass Section 7.6 (3), (5) Density ≤ 30 dBm/500kHz UNII-3 15.407(g) Frequency Stability ± 20 ppm Pass Section 7.7 15.407(b)(1), Undesirable Emissions Refer to Section 7.8 Pass (4)(i) General Field Strength Emissions in Section 15.205, 15.209 Radiated Limits(Restricted Bands restrictedbands must 7.8 & 7.9 15.407(b)(5), Pass andRadiated Emission meet theradiated limits (6), (7) Limits) detailed in15.209 AC Conducted Line Section 15.207 Emissions < FCC 15.207 limits Pass Conducted 7.10 150kHz - 30MHz Notes: 1) The analyzer plots shown in this section were all taken with a correction table loaded into the analyzer. The correction table was used to account for the losses of the cables and attenuators used as part of the system to connect the EUT to the analyzer at all frequencies of interest. 2) All modes of operation and data rates were investigated. For radiated emission test, every axis (X, Y, Z) was also verified. The test results shown in the following sections represent the worst case emissions. 3) Test Items “6dB Bandwidth” & “Band Edge / Out-of-Band Emissions” have been assessed MIMO transmission, and showed the worst test data in this report. Besides, two items were accessed by APIN0514 only due its high power than APIN0505. FCC ID: Q9DAPIN0504505 Page Number: 23 of 426

Report No.: 1906TW0102-U4 7.2. 26dB Bandwidth Measurement 7.2.1.Test Limit N/A 7.2.2.Test Procedure used ANSI C63-2013 - Section 12.4.1 7.2.3.Test Setting 1. The analyzers’ automatic bandwidth measurement capability was used to perform the 26dB bandwidth measurement. The “X” dB bandwidth parameter was set to X = 26. The automatic bandwidth measurement function also has the capability of simultaneously measuring the 99% occupied bandwidth. The bandwidth measurement was not influenced by any intermediated power nulls in the fundamental emission. 2. RBW = approximately 1% of the emission bandwidth. 3. VBW ≥ 3×RBW. 4. Detector = Peak. 5. Trace mode = max hold. 7.2.4.Test Setup FCC ID: Q9DAPIN0504505 Page Number: 24 of 426

Report No.: 1906TW0102-U4 7.2.5.Test Result Product ACCESS POINT Temperature 24°C Test Engineer Kevin Ker Relative Humidity 59% Test Site SR2 Test Date 2019/06/05 Model No. APIN0504 Test Item 26dB Bandwidth Test Mode Data Rate/ Channel No. Frequency 26dB Bandwidth 99% Bandwidth MCS (MHz) (MHz) (MHz) Ant 0 / Ant 0 + 1 802.11a 6Mbps 36 5180 22.05 16.80 802.11a 6Mbps 44 5220 21.58 16.71 802.11a 6Mbps 48 5240 21.24 16.71 802.11a 6Mbps 149 5745 21.66 16.68 802.11a 6Mbps 157 5785 21.70 16.75 802.11a 6Mbps 165 5825 21.72 16.82 802.11ac-VHT20 MCS0 36 5180 22.08 17.88 802.11ac-VHT20 MCS0 44 5220 21.26 17.81 802.11ac-VHT20 MCS0 48 5240 21.45 17.86 802.11ac-VHT20 MCS0 149 5745 21.15 17.82 802.11ac-VHT20 MCS0 157 5785 21.60 17.87 802.11ac-VHT20 MCS0 165 5825 21.93 17.93 802.11ac-VHT40 MCS0 38 5190 39.39 36.31 802.11ac-VHT40 MCS0 46 5230 39.74 36.29 802.11ac-VHT40 MCS0 151 5755 39.82 36.30 802.11ac-VHT40 MCS0 159 5795 39.33 36.39 802.11ac-VHT80 MCS0 42 5210 80.83 75.75 802.11ac-VHT80 MCS0 155 5775 80.48 75.88 802.11ax-HE20 MCS0 36 5180 21.31 19.10 802.11ax-HE20 MCS0 44 5220 22.03 19.04 802.11ax-HE20 MCS0 48 5240 21.22 19.03 802.11ax-HE20 MCS0 149 5745 21.25 19.06 802.11ax-HE20 MCS0 157 5785 23.02 19.04 802.11ax-HE20 MCS0 165 5825 22.70 19.14 FCC ID: Q9DAPIN0504505 Page Number: 25 of 426

Report No.: 1906TW0102-U4 Test Mode Data Rate/ Channel No. Frequency 26dB Bandwidth 99% Bandwidth MCS (MHz) (MHz) (MHz) Ant 0 / Ant 0 + 1 802.11ax-HE40 MCS0 38 5190 39.81 37.62 802.11ax-HE40 MCS0 46 5230 39.74 37.69 802.11ax-HE40 MCS0 151 5755 39.87 37.67 802.11ax-HE40 MCS0 159 5795 39.83 37.68 802.11ax-HE80 MCS0 42 5210 81.34 77.05 802.11ax-HE80 MCS0 155 5775 81.15 76.96 FCC ID: Q9DAPIN0504505 Page Number: 26 of 426

Report No.: 1906TW0102-U4 802.11a 26dB Bandwidth & 99% Bandwidth - Ant 0 / Ant 0 + 1 Channel 36 (5180MHz) Channel 44 (5220MHz) Channel 48 (5240MHz) Channel 149 (5745MHz) Channel 157 (5785MHz) Channel 165 (5825MHz) FCC ID: Q9DAPIN0504505 Page Number: 27 of 426

Report No.: 1906TW0102-U4 802.11ac-VHT20 26dB Bandwidth & 99% Bandwidth - Ant 0 / Ant 0 + 1 Channel 36 (5180MHz) Channel 44 (5220MHz) Channel 48 (5240MHz) Channel 149 (5745MHz) Channel 157 (5785MHz) Channel 165 (5825MHz) FCC ID: Q9DAPIN0504505 Page Number: 28 of 426

Report No.: 1906TW0102-U4 802.11ac-VHT40 26dB Bandwidth & 99% Bandwidth - Ant 0 / Ant 0 + 1 Channel 38 (5190MHz) Channel 46 (5230MHz) Channel 151 (5755MHz) Channel 151 (5795MHz) 802.11ac-VHT80 26dB Bandwidth & 99% Bandwidth - Ant 0 / Ant 0 + 1 Channel 42 (5210MHz) Channel 155 (5775MHz) FCC ID: Q9DAPIN0504505 Page Number: 29 of 426

Report No.: 1906TW0102-U4 802.11ax-HE20 26dB Bandwidth & 99% Bandwidth - Ant 0 / Ant 0 + 1 Channel 36 (5180MHz) Channel 44 (5220MHz) Channel 48 (5240MHz) Channel 149 (5745MHz) Channel 157 (5785MHz) Channel 165 (5825MHz) FCC ID: Q9DAPIN0504505 Page Number: 30 of 426

Report No.: 1906TW0102-U4 802.11ax-HE40 26dB Bandwidth & 99% Bandwidth - Ant 0 / Ant 0 + 1 Channel 38 (5190MHz) Channel 46 (5230MHz) Channel 151 (5755MHz) Channel 159 (5795MHz) 802.11ax-HE80 26dB Bandwidth & 99% Bandwidth - Ant 0 / Ant 0 + 1 Channel 42 (5210MHz) Channel 155 (5775MHz) FCC ID: Q9DAPIN0504505 Page Number: 31 of 426

Report No.: 1906TW0102-U4 7.3. 6dB Bandwidth Measurement 7.3.1.Test Limit The minimum 6dBbandwidth shall be at least 500 kHz. 7.3.2.Test Procedure used ANSI C63-2013 - Section 12.4.2 7.3.3.Test Setting 1. Set center frequency to the nominal EUT channel center frequency. 2. RBW = 100 kHz. 3. VBW≧ 3 × RBW. 4. Detector = Peak. 5. Trace mode = max hold. 6. Sweep = auto couple. 7. Allow the trace to stabilize. 8. Measure the maximum width of the emission that is constrained by the frequencies associated with the two outermost amplitude points (upper and lower frequencies) that are attenuated by 6 dB relative to the maximum level measured in the fundamental emission. 7.3.4.Test Setup FCC ID: Q9DAPIN0504505 Page Number: 32 of 426

Report No.: 1906TW0102-U4 7.3.5.Test Result Product ACCESS POINT Temperature 24°C Test Engineer Kevin Ker Relative Humidity 59% Test Site SR2 Test Date 2019/06/05 Model No. APIN0504 Test Item 6dB Bandwidth Test Mode Data Rate/ Channel Frequency 6dB Bandwidth Limit Result MCS No. (MHz) (MHz) (MHz) Ant 0 / Ant 0 + 1 802.11a 6Mbps 149 5745 16.41 ≥ 0.5 Pass 802.11a 6Mbps 157 5785 16.38 ≥ 0.5 Pass 802.11a 6Mbps 165 5825 16.36 ≥ 0.5 Pass 802.11ac-VHT20 MCS0 149 5745 17.62 ≥ 0.5 Pass 802.11ac-VHT20 MCS0 157 5785 17.60 ≥ 0.5 Pass 802.11ac-VHT20 MCS0 165 5825 17.62 ≥ 0.5 Pass 802.11ac-VHT40 MCS0 151 5755 36.38 ≥ 0.5 Pass 802.11ac-VHT40 MCS0 159 5795 36.38 ≥ 0.5 Pass 802.11ac-VHT80 MCS0 155 5775 75.85 ≥ 0.5 Pass 802.11ax-HE20 MCS0 149 5745 18.99 ≥ 0.5 Pass 802.11ax-HE20 MCS0 157 5785 18.95 ≥ 0.5 Pass 802.11ax-HE20 MCS0 165 5825 18.99 ≥ 0.5 Pass 802.11ax-HE40 MCS0 151 5755 36.97 ≥ 0.5 Pass 802.11ax-HE40 MCS0 159 5795 37.63 ≥ 0.5 Pass 802.11ax-HE80 MCS0 155 5775 76.59 ≥ 0.5 Pass FCC ID: Q9DAPIN0504505 Page Number: 33 of 426

Report No.: 1906TW0102-U4 802.11a 6dB Bandwidth - Ant 0 / Ant 0 + 1 Channel 149 (5745MHz) Channel 157 (5785MHz) Channel 165 (5825MHz) FCC ID: Q9DAPIN0504505 Page Number: 34 of 426


Document Created: 2019-10-03 12:53:07
Document Modified: 2019-10-03 12:53:07
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC