User Manual pt 2

FCC ID: Q9DAPIN0334335

Users Manual

Download: PDF
FCCID_2993834

Aruba 330 Series Wireless Access Point Installation Guide The Aruba 330 Series wireless access points (AP-334, AP-335, IAP-334, and Table 1: LED Status Indicators Figure 4 Back Panel Power IAP-335) support IEEE 802.11ac standards for high-performance WLAN. This The ENET0 and ENET1 ports support PoE-in, allowing one port to draw device is equipped with two dual-band radios, which provide network USB port LED Color/State Meaning power from an 802.3at source. access and monitor the network simultaneously. This access point delivers DC power socket high-performance 802.11n 2.4 GHz and 802.11ac 5 GHz functionality, while System Status Off Device powered off Ethernet ports also supporting 802.11a/b/g wireless services. Multi-user Multiple-in, The 330 Series does not support 802.3af PoE power sources. Multiple-output (MU-MIMO) is enabled when operating in 5GHz mode for i Green- Blinking* Device booting, not ready for use optimal performance. Green- Solid Device ready for use 48V 0.75A ENET1 ENET0 If PoE is not available, the access point has a single 48V DC power input to 57V 600mA The AP-334 and AP-335 access points work in conjunction with an Aruba controller, while the IAP-334 and IAP-335 access points can be configured Green- Flashing** Device operating in restricted mode. Meets support the AP-AC-48V36C AC-to-DC power adapter kit (sold separately). one of the following conditions: using a built-in virtual controller. When both 802.3at and DC power sources are available, the DC power Uplink negotiated in sub-optimal speed The 330 Series wireless access points provides the following capabilities: (<1Gbps), or source will take precedence. The access point will simultaneously draw a Ethernet radio is in non High-Throughput minimal current from the PoE source. In the event that the DC source fails, IEEE 802.11a/b/g/n/ac wireless access point (HT) mode the access point will switch to the 802.3at source. IEEE 802.11a/b/g/n/ac wireless air monitor Red- Solid System error condition The ENET0 and ENT1 Ethernet ports support Dual-hitless Failover when IEEE 802.11a/b/g/n/ac spectrum analysis both ports are connected to 802.3at separate PoE power sources. If the Compatible with IEEE 802.3at PoE+ power sources Radio Status Off Device powered off; or both radios disabled primary power source fails, the access point will immediately switch the Centralized management, configuration and upgrades Console port secondary power source with minimal impact to operation of the device. Green- Solid Both radios enabled in access mode CONSOLE When both ENET0 and ENET1 are wired to 802.3 PoE sources, the access Green- Blinking One radio enabled in access mode; one radio K point will draw power primarily from one source, while the secondary Package Contents disabled power source draws minimum current to keep the device active and is only 330 Series access point Amber- Solid Both radios enabled in monitor mode Kensington Lock used in the event of a failover. 9/16" and 15/16” Ceiling Rail Adapters Reset button Amber- Blinking One radio enabled in access mode; one radio Safety, Compliance, and Warranty Information guide disabled Before You Begin Aruba Instant Quick Start Guide (IAP-334 and IAP-335 only) Alternating Green: one radio in access mode Aruba Professional Installation Guide (IAP-334 only) FCC Statement: Improper termination of access points installed in the Amber: one radio in monitor mode Console Port Aruba 330 Series Wireless Access Point Installation Guide (this document) United States configured to non-US model controllers is a violation of The console port allows the user to connect the access point directly to a the FCC grant of equipment authorization. Any such willful or intentional * Blinking: 1s on/1s off Inform your supplier if there are any incorrect, missing, or damaged **Flashing: off a fraction of a second every 2s serial terminal or laptop for local management. Connect the device to a violation may result in a requirement by the FCC for immediate parts. If possible, retain the carton, including the original packing terminal or terminal server using an Ethernet cable. termination of operation and may be subject to forfeiture (47 CFR 1.80). materials. Use these materials to repack and return the unit to the External Antenna Connectors The port is an RJ45 connector with pin-out details in Figure 5. supplier if needed. The AP-334 and IAP-334 access points are equipped with four external Figure 5 Console Port Pin-Out antenna connectors located on the front corners of the access point (see EU Statement: Lower power radio LAN product operating in 2.4 GHz and 5 GHz bands. Figure 2). Software Figure 2 External Antenna Connectors RJ45 Console Port Please refer to the ArubaOS User Guide/Instant User Guide for details on restrictions. The AP-334 and AP-335 access points require ArubaOS 6.5.0.0 or higher. For additional information, refer to the ArubaOS User Guide and ArubaOS Quick Produit réseau local radio basse puissance operant dans la bande Start Guide. fréquence 2.4 GHz et 5 GHz. Merci de vous referrer au ArubaOS User Guide/Instant User Guide pour les details des restrictions. The IAP-334 and IAP-335 access points require Instant 4.3.0.0 or higher. For additional information, refer to the Aruba Instant User Guide and Aruba ANT1 ANT0 Low Power FunkLAN Produkt, das im 2.4 GHz und im 5 GHz Band Instant Quick Start Guide. arbeitet. Weitere Informationen bezlüglich Einschränkungen finden Sie im ArubaOS User Guide/Instant User Guide. Aruba access points are classified as radio transmission devices, and are Ethernet Ports subject to government regulations of the host country. The network Apparati Radio LAN a bassa Potenza, operanti a 2.4 GHz e 5 GHz. Fare administrator(s) is/are responsible for ensuring that configuration and The back panel of the 330 Series access point is equipped with two Ethernet riferimento alla ArubaOS User Guide/Instant User Guide per avere operation of this equipment meet all regulatory standards of their ports (ENET0 and ENET1) to support wired-network connectivity. These informazioni detagliate sulle restrizioni. country/domain. For complete list of approved channels in your ports support IEEE 802.3at Power over Ethernet (PoE) compliant sources, country, refer to the Aruba Downloadable Regulatory Table at accepting 56V DC (nominal) as a standard powered device (PD) from power www.arubanetworks.com. sourcing equipment, such as a PoE midspan injector or network Access Point Pre-Installation Checklist infrastructure that supports PoE. Before installing your 330 Series access point, ensure that you have the ANT2 ANT3 ENET0: 100/1000/2500Base-T auto-sensing MDI/MDX RJ45 port. following: 330 Series Hardware Overview ENET1: 100/1000Base-T auto-sensing MDI/MDX RJ45 port. CAT5E cable or better Figure 1 LEDs Figure 6 Ethernet Port Pin-Out One of the following power sources: IEEE 802.3at Power over Ethernet (PoE) source. The PoE source can be any power source equipment (PSE) controller or midspan PSE 1000Base-T Gigabit RJ-45 Female Signal Name Function Ethernet Port Pin-Out device 1 BI_DA+ Bi-directional pair +A 2 BI_DA- Bi-directional pair -A Aruba AP-AC-48V36C adapter kit (sold separately) External antennas for this device must be installed by an Aruba Certified 3 BI_DB+ Bi-directional pair +B Mobility Professional (ACMP) or other Aruba-certified technician, using 4 BI_DC+ Bi-directional pair +C For AP-334 and AP-335 only: manufacturer-approved antennas only. 5 BI_DC- Bi-directional pair -C 6 BI_DB- Bi-directional pair -B Aruba controller provisioned on the network: The Equivalent Isotropically Radiated Power (EIRP) levels for all external antenna devices must not exceed the regulatory limit set by the host 7 BI_DD+ Bi-directional pair +D Layer 2/3 network connectivity to your access point 8 BI_DD- Bi-directional pair -D country/domain. One of the following network services: Installers are required to record the antenna gain for this device in the Aruba Discovery Protocol (ADP) system management software. Kensington Lock Slot DNS server with an “A” record LEDs The 330 Series is equipped with a Kensington lock slot for additional security, shown in Figure 4. DHCP Server with vendor-specific options. USB Interface The 330 Series access points have two LEDs that indicate the system and radio status. The 330 Series is equipped with a USB port for connectivity with cellular Reset Button Aruba Networks, Inc., in compliance with governmental requirements, modems and other USB client devices. has designed the 330 Series access points so that only authorized The LEDs have three operating modes that can be selected in the system The reset button can be used to return the access point to factory default network administrators can change the settings. For more information management software: When powered by an 802.3at or DC power source, the USB port can supply settings. To reset the access point, refer to the steps below: about access point configuration, refer to the ArubaOS Quick Start Guide/ power up to 5W/1A. Instant Quick Start Guide and ArubaOS User Guide/Instant User Guide. Default mode: refer to Table 1 1. Power off the access point. Off mode: LEDs are off Figure 3 USB Port 2. Press and hold the reset button using a small, narrow object, such as a Blink mode: LEDs blink green paperclip. 3. Power-on the access point without releasing the reset button. The power LED will flash within 5 seconds. 4. Release the reset button. The power LED will flash again within 15 seconds indicating that the reset is completed. The access point will now continue to boot with the factory default settings.

Verifying Pre-Installation Connectivity 5. Hold the access point next to the ceiling tile rail with the ceiling tile rail mounting slots at approximately a 30-degree angle to the ceiling tile rail The instructions for this section are applicable to the AP-334 and AP-335 (see Figure 8). Make sure that any cable slack is above the ceiling tile. only. 6. Pushing toward the ceiling tile, rotate the access point clockwise until the device clicks into place on the ceiling tile rail. Before installing access points in a network environment, make sure that Figure 8 Mounting the Access Point they are able to locate and connect to the controller after power on. Specifically, you must verify the following conditions: When connected to the network, each access point is assigned a valid IP Aruba 330 Series Wireless address Access points are able to locate the controller Access Point Refer to the ArubaOS Quick Start Guide for instructions on locating and connecting to the controller. Installation Guide Pre-Installation Network Requirements After WLAN planning is complete and the appropriate products and their placement have been determined, the Aruba controller(s) must be installed and initial setup performed before the Aruba access points are deployed. a Hewlett Packard Enterprise company For initial setup of the controller, refer to the ArubaOS Quick Start Guide for the software version installed on your controller. Contacting Aruba Networks 7. On the AP-334 and IAP-334, install the external antennas according to the Identifying Specific Installation Locations manufacturer’s instructions, and connect the antennas to the antenna Web Support You can mount the 330 Series access point on a wall or on the ceiling. Use interfaces on the access point. the access point placement map generated by Aruba’s RF Plan software Main Site http://www.arubanetworks.com application to determine the proper installation location(s). Each location Support Site https://support.arubanetworks.com should be as close as possible to the center of the intended coverage area Connecting Required Cables and should be free from obstructions or obvious sources of interference. Airheads Social Forums and Knowledge Base http://www.community.arubanetworks.com Install cables in accordance with all applicable local and national regulations These RF absorbers/reflectors/interference sources will impact RF and practices. North American Telephone 1-800-943-4526 (Toll Free) propagation and should have been accounted for during the planning phase 1-408-754-1200 and adjusted for in RF plan. International Telephones arubanetworks.com/support-services/aruba-support- Verifying Post-Installation Connectivity program/contact-support/ Identifying Known RF Absorbers/Reflectors/Interference Software Licensing Site licensing.arubanetworks.com The integrated LEDs on the access point can be used to verify that the device Sources is receiving power and initializing successfully (see Table 1). Refer to the End-of-life Information http://www.arubanetworks.com/support-services/end- Identifying known RF absorbers, reflectors, and interference sources while ArubaOS Quick Start Guide for further details on verifying post-installation of-life/ in the field during the installation phase is critical. Make sure that these network connectivity. Security Incident Response Team (SIRT) http://www.arubanetworks.com/support-services/ sources are taken into consideration when you attach an access point to its security-bulletins/ fixed location. Examples of sources that degrade RF performance include: Configuring the 330 Series Support Email Addresses Cement and brick Americas, EMEA and APAC support@arubanetworks.com Objects that contain water The instructions for the following section are applicable to AP-334 and AP- Security Incident Response Team (SIRT) sirt@arubanetworks.com 335 model access points only. Metal Microwave ovens Access Point Provisioning/Reprovisioning Wireless phones and headsets Provisioning parameters are unique to each access point. These local access point parameters are initially configured on the controller which are then Installing the Access Point pushed out to the access points and stored on the devices. Aruba Copyright recommends that provisioning settings be configured via the ArubaOS Web © Copyright 2016 Hewlett Packard Enterprise Development LP Refer to the following steps to install your Aruba 330 Series access point UI only. Refer to the ArubaOS User Guide for complete details. using the AP Ceiling Rail Mount Kit (AP-220-MNT-C1). Open Source Code Access Point Configuration Certain Aruba products include Open Source software code developed by third parties, including software Using the Ceiling Rail Adapter code subject to the GNU General Public License ("GPL"), GNU Lesser General Public License ("LGPL"), or other Open Source Licenses. The Open Source code used can be found at this site: Configuration parameters are network or controller specific and are The 330 Series ships with two ceiling rail adapters for 9/16” and 15/16” configured and stored on the controller. Network configuration settings are http://www.arubanetworks.com/open_source ceiling rails. Additional wall mount adapters and ceiling rail adapters for pushed out to the access points, but remain stored on the controller. other rail styles are available as accessory kits. Warranty Configuration settings can be configured via the ArubaOS Web UI or This hardware product is protected by an Aruba warranty. For details, see the Safety, Compliance, and This device must be professionally installed and serviced by an ACMP or ArubaOS CLI. Refer to their respective guides for further details: the ArubaOS Warranty Information Guide included with this device. other Aruba-certified technician. The installer is responsible for securing User Guide. the access point onto the ceiling tile rail in accordance with the steps below. Failure to properly install this product may result in physical injury and/or damage to property. 1. Pull the necessary cables through a prepared hole in the ceiling tile near where the access point will be placed. 2. Place the adapter against the back of the access point with the adapter at an angle of approximately 30 degrees to the tabs (see Figure 7). 3. Twist the adapter clockwise until it snaps into place in the tabs (see Figure 7). Figure 7 Attaching the Ceiling Rail Adapter a Hewlett Packard Enterprise company www.arubanetworks.com 1344 Crossman Avenue Sunnyvale, California 94089 Phone: 408.227.4500 Fax 408.227.4550 4. If necessary, connect the console cable to the console port on the back of Aruba 330 Series Wireless Access Point | Installation Guide Part Number 0511873-03 |May 2016 the access point.


Document Created: 8830-06-18 00:00:00
Document Modified: 8830-06-18 00:00:00
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC