User Manual Safety Guide

FCC ID: Q9DAPIN0304305

Users Manual

Download: PDF
FCCID_3146941

Aruba 300 Series Wireless Access Point Regulatory Compliance and Safety Information Guide Introduction This document contains domestic and international regulatory compliance and safety information for 300 Series access points. To ensure that this device complies with the regulatory standards for your region, please refer to the sections below.  Electrical and Environmental Specifications  Regulatory Information  Proper Disposal of Aruba Equipment Electrical and Environmental Specifications For additional specifications on this product, please refer to the product data sheet at www.arubanetworks.com/ safety_addendum. All Aruba access points should be professionally installed by an Aruba Certified Mobility Professional (ACMP). The installer is responsible for ensuring that grounding is available and meets applicable national and electrical codes. Tous les points d'accès Aruba doivent impérativement être installés par un professionnel agréé. Ce dernier doit s'assurer que l'appareil est mis à la terre et que le circuit de mise à la terre est conforme aux codes électriques nationaux en vigueur. Electrical  Ethernet:  One 100/1000 Base-T auto-sensing Ethernet RJ45 interface  Power over Ethernet IEEE 802.3at 56VDC (nominal) and 802.3af 48VDC (nominal).  Power:  Maximum (worst-case) power consumption: 13.5W (802.3af PoE) or 12W (DC)  Excludes power consumed by external USB device (and internal overhead); this could add up to 6W (PoE) or 5.5W (DC) for 5W/1A USB device  Direct DC source: 12Vdc nominal, +/- 5%  Power over Ethernet (PoE): 802.3at and 802.3af complaint source  Connect only to IEC 60950-1 or IEC 60601-1 3rd edition products and power sources. If a power adapter other than the Aruba-approved adapter is used in the US or Canada, it should be NRTL listed, with an output rated 12Vdc, minimum 2A, marked “LPS” and “Class 2”, and suitable for plugging into a standard power receptacle in the US and Canada. Environmental  Operating:  Temperature: 0° C to +50° C (+32° F to +122° F)  Humidity: 5% to 93% non-condensing  Storage and transport:  Temperature: -40° C to +70° C (40° F to +158° F) Regulatory Information The following regulatory model names apply to the 300 Series access points:  AP-304/IAP-304: APIN0304  AP-305/IAP-305: APIN0305 0511891-02 | September 2016 1

Aruba Networks provides a multi-language document that contains country-specific restrictions and additional safety and regulatory information for all Aruba access points. This document can be viewed or downloaded at www.arubanetworks.com. FCC This device is electronically labeled. To view the FCC ID for controller-managed access points: 1. Log into the controller WebUI 2. Navigate to Maintenance > Controller > About To view the FCC ID for Instant access points: 1. Log into the virtual controller WebUI 2. Navigate to Maintenance > About RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits. This equipment should be installed and operated with a minimum distance of 7.87 inches (20cm) between the radiator and your body for 2.4 GHz and 5 GHz operations. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Déclaration sur les limites d'exposition aux radiofréquences : cet équipement est conforme aux limites d'exposition aux rayonnements radioélectriques spécifiées par la FCC. Il doit être installé et utilisé à une distance minimale de 20 cm par rapport à votre corps pour les fréquences de 2,4 et 5 GHz. Cet émetteur-récepteur ne doit pas être utilisé ou situé à proximité d'autres antennes ou émetteurs-récepteurs. The device could automatically discontinue transmission in case of absence of information to transmit, or operational failure. Note that this is not intended to prohibit transmission of control or signaling information or the use of repetitive codes where required by the technology. FCC Class B Part 15 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer’s instructions, may cause interference harmful to radio communications. Operation is subject to the following conditions:  This device may not cause harmful interference.  This device must accept any interference received, including interference that may cause undesired operation. If this equipment does cause interference, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio or TV technician for help. Users are advised that high power Radars are allocated as primary users of the bands 5250-5350 MHz and 5650-5850 MHz and these Radars could cause interference and/or damage to Licensed Exempt WLAN devices. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. Toute modification effectuée sur cet équipement sans l'autorisation expresse de la partie responsable de la conformité est susceptible d'annuler son droit d'utilisation. Canada Complies with the Class B limits for radio noise emissions as set out in the interference-causing equipment standard entitled “Digital Apparatus,” CAN ICES-3(B)/NMB-3(B). Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (E.I.R.P.) does not exceed the limit necessary for successful communication. This device complies with Industry Canada license-exempt RSS standard(s). 2 Aruba 300 Series Wireless Access Point | Regulatory Compliance and Safety Information Guide

Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Déclaration d’Industrie Canada Cet appareil numerique de la classe B respecte toutes les exigencies du Reglement sur le materiel brouilleur du Canada. Conformément aux réglementations d’Industrie Canada, cet émetteur-récepteur radio doit être utilisé uniquement avec une antenne dont le type et le gain maximal doivent être approuvés par Industrie Canada. Pour réduire les interférences radio potentielles, le type d’antenne et son gain doivent être choisis de façon à ce que la puissance isotrope rayonnée équivalente (PIRE) ne dépasse pas les valeurs nécessaires à une communication efficace. Ce périphérique est conforme aux règlements RSS exempts de licence d’Industrie Canada. L’utilisation de ce périphérique est soumise aux deux conditions suivantes : (1) ce périphérique ne doit pas provoquer d’interférences, et (2) ce périphérique doit accepter toute interférence, y compris les interférences susceptibles de provoquer un dysfonctionnement. This equipment complies with IC RSS-102 RF exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. Under Industry Canada regulations, when operated in 5150 to 5250 MHz frequency range, this device is restricted to indoor use to reduce the potential for harmful interference with co-channel Mobile Satellite Systems. Users are advised that high power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850MHz and that these radars could cause interference and/or damage to LE-LAN devices. Conformément aux réglementations d’Industrie Canada, en cas d'utilisation dans la plage de fréquences de 5150 à 5250 MHz, cet appareil doit uniquement être utilisé en intérieur afin de réduire les risques d'interférence avec les systèmes satellites mobiles partageant le même canal. Les utilisateurs êtes avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu'ils ont la priorité) pour les bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL EU Regulatory Conformance Aruba Networks Inc., hereby declares that this product is in compliance with the directives listed below:  EMC Directive 2014  Low Voltage Directive 2014  R&TTE Directive 1999  REACH Regulation (EC) No.: 1907/2006  RoHS Directive 2011  WEEE Directive 2012 A Declaration of Conformity for these directives is available for viewing at www.arubanetworks.com. EMC Class B Warning 이 기기는 가정용 (B 급 ) 전자파적합기기로서 주로 가정에서 사용하는 것을 적으로 하며 , 든 지역에서 사용할 수 있습니다 . RF Warning 해당무선설비는 전파혼신의 가능성이 있으므로 인명안전과 관련된 서비스는 할 수 없습니다 Medical 1. Equipment not suitable for use in the presence of flammable mixtures. 2. Connect to only IEC 60950-1 or IEC 60601-1 3rd edition certified products and power sources. The end user is responsible for the resulting medical system complies with the requirements of IEC 60601-1 3rd edition. 3. Wipe with a dry cloth, no additional maintenance required. Aruba 300 Series Wireless Access Point | Regulatory Compliance and Safety Information Guide 3

4. No serviceable parts, the unit must be sent back to the manufacturer for repair. 5. No modifications are allowed without Aruba approval. 第十二條 → 經型式認證合格之低 率射頻電機，非經許可，公司 商號或使用者均不得擅自變更頻率 大 率或變更原設計之特性及 能 第十四條 → 低 率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用 前項合法通信，指依電信法規定作業之無線電通信 低 率射頻電機須忍受合法通信或工業 科學及醫療用電波輻射性電機設備之干擾 Expected Service Life 10 years. For additional compliance information, refer to the regulatory label on the back of this device. Proper Disposal of Aruba Equipment Dispose of Aruba products per local regulation. For the most current information about Global Environmental Compliance and Aruba products, visit www.arubanetworks.com. Waste of Electrical and Electronic Equipment Aruba products at end of life are subject to separate collection and treatment in the EU Member States, Norway, and Switzerland and therefore are marked with the symbol shown at the left (crossed-out wheelie bin). The treatment applied at end of life of these products in these countries shall comply with the applicable national laws of countries implementing Directive 2002/96/EC on Waste of Electrical and Electronic Equipment (WEEE). India RoHS This product complies with RoHS requirements as prescribed by E-Waste (Management & Handling) Rules, governed by the Ministry of Environment & Forests, Government of India. European Union RoHS Aruba products also comply with the EU Restriction of Hazardous Substances Directive 2011/65/EC (RoHS). EU RoHS restricts the use of specific hazardous materials in the manufacture of electrical and electronic equipment. Specifically, restricted materials under the RoHS Directive are Lead (including Solder used in printed circuit assemblies), Cadmium, Mercury, Hexavalent Chromium, and Bromine. Some Aruba products are subject to the exemptions listed in RoHS Directive Annex 7 (Lead in solder used in printed circuit assemblies). Products and packaging will be marked with the “RoHS” label shown at the left indicating conformance to this directive. China RoHS Aruba products also comply with China environmental declaration requirements and are labeled with the “EFUP 10” label shown at the left. 10 ᴹ∂ᴹᇣ⢙䍘༠᰾ Hazardous Materials Declaration ᴹ∂ᴹᇣ⢙䍘ᡆ‫ݳ‬㍐˄Hazardous Substance˅ 䜘Ԧ਽〠 䫵 ⊎ 䭹 ‫ޝ‬ԧ䬜 ཊⓤ㚄㤟 ཊⓤҼ㤟䟊 (Parts) ˄Pb˅ ˄Hg˅ ˄Cd˅ ˄Cr6+˅ ˄PBB˅ ˄PBDE˅ ⭥䐟⁑ඇ X O O O O O (circuit modules) ⭥㔶৺⭥㔶㓴Ԧ O O O O O O (Cables & Cable Assemblies) 䠁኎䜘Ԧ O O O O O O (Metal Parts) ກᯉ઼㚊ਸ⢙䜘Ԧ O O O O O O (Plastic and Polymeric Parts) O: 㺘⽪䈕ᴹ∂ᴹᇣ⢙䍘൘䈕䜘Ԧᡰᴹ൷䍘ᶀᯉѝⲴਜ਼䟿൷൘ SJ/T11363-2006 ḷ߶㿴ᇊⲴ䲀䟿㾱≲ ԕлDŽIndicates that the concentration of the hazardous substance in all homogeneous materials in the parts is below the relevant threshold of the SJ/T11363-2006 standard. X: 㺘⽪䈕ᴹ∂ᴹᇣ⢙䍘㠣ቁ൘䈕䜘ԦⲴḀа൷䍘ᶀᯉѝⲴਜ਼䟿䎵ࠪ SJ/T11363-2006 ḷ߶㿴ᇊⲴ䲀 䟿㾱≲DŽIndicates that the concentration of the hazardous substance of at least one of all homogeneous materials in the parts is above the relevant threshold of the SJ/T11363-2006 standard. ሩ䬰୞ѻᰕⲴᡰ୞ӗ૱ˈᵜ㺘ᱮ⽪‫׋‬ᓄ䬮Ⲵ⭥ᆀؑ᚟ӗ૱ਟ㜭वਜ਼䘉Ӌ⢙䍘DŽ This table shows where these substances may be found in the supply chain of electronic information products, as of the date of sale of the enclosed product. ↔ḷᘇѪ䪸ሩᡰ⎹৺ӗ૱Ⲵ⧟‫⭘֯؍‬ᵏḷᘇ. ḀӋ䴦䜘ԦՊᴹањн਼Ⲵ⧟‫⭘֯؍‬ᵏ (ֻྲ,⭥⊐অ‫⁑ݳ‬ඇ)䍤൘ަӗ૱к. ↔⧟‫⭘֯؍‬ᵏ䲀ਚ䘲⭘Ҿӗ૱ᱟ൘ӗ૱᡻޼ѝᡰ㿴ᇊⲴᶑԦлᐕ֌. The Environment- Friendly Use Period (EFUP) for all enclosed products and their parts are per the symbol shown here. The Environment- Friendly Use Period is valid only when the product is operated under the conditions defined in the product manual. © Copyright 2016 Hewlett Packard Enterprise Development LP www.arubanetworks.com 1344 Crossman Avenue Sunnyvale, California 94089 Phone: 408.227.4500 Fax: 408.227.4550 4 Aruba 300 Series Wireless Access Point | Regulatory Compliance and Safety Information Guide


Document Created: 2017-12-15 05:04:10
Document Modified: 2017-12-15 05:04:10
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC