Revised Manual

FCC ID: Q9DAPIN0214215

Users Manual

Download: PDF
FCCID_2590689

AP-210 Series Wireless Access Point The Aruba AP-214 and AP-215 wireless access points support the IEEE 802.11n standard for Figure 2 AP-210 Series Side View (AP-214 shown) The 10/100/1000 Mbps Ethernet ports are on the bottom of the AP. These ports have RJ-45 high-performance WLAN. These access points use MIMO (Multiple-in, Multiple-out) technology ANT2 ANT1 ANT0 female connectors with the pin-outs shown in Figure 6. and other high-throughput mode techniques to deliver high-performance, 802.11n 2.4 GHz and 802.11ac 5 GHz functionality while simultaneously supporting existing 802.11a/b/g wireless Figure 6 Gigabit Ethernet Port Pin-Out Aruba Networks, Inc., in compliance with governmental requirements, has services. The AP-210 Series access points work only in conjunction with an Aruba Controller. designed the AP-210 Series access points so that only authorized network 1000Base-T Gigabit RJ-45 Female Signal Name Function The Aruba AP-210 Series access point provides the following capabilities: Ethernet Port Pin-Out administrators can change the settings. For more information about AP 1 BI_DA+ Bi-directional pair +A  Wireless transceiver BI_DA- Bi-directional pair -A configuration, refer to the ArubaOS Quick Start Guide and ArubaOS User 2  Protocol-independent networking functionality 3 BI_DB+ Bi-directional pair +B Guide.  IEEE 802.11a/b/g/n/ac operation as a wireless access point 4 BI_DC+ Bi-directional pair +C  IEEE 802.11a/b/g/n/ac operation as a wireless air monitor 5 BI_DC- Bi-directional pair -C  Compatibility with IEEE 802.3at PoE+ and 802.3af PoE 6 BI_DB- Bi-directional pair -B 7 BI_DD+ Bi-directional pair +D Access points are radio transmission devices and as such are subject to  Central management configuration and upgrades through a controller 8 BI_DD- Bi-directional pair -D governmental regulation. Network administrators responsible for the This device must be professionally installed and serviced by a trained Aruba Certified USB Port ! configuration and operation of access points must comply with local broadcast regulations. Specifically, access points must use channel assignments Mobility Professional (ACMP) or similar Aruba-certified technician. Aruba access DC Power Socket appropriate to the location in which the access point will be used. points are classified as radio transmission devices, and are subject to government ! regulations of the host country. The network administrator(s) is/are responsible for ensuring that configuration and operation of this equipment is in compliance with External Antenna Connectors The AP-214 is equipped with three external antenna connectors. The connectors are labeled If PoE is not available, an optional Aruba AP AC-DC adapter kit (sold separately) can be used to power the AP-210 Series. their country’s regulations. For complete list of approved channels in your country, Additionally, a locally-sourced AC-to-DC adapter (or any DC source) can be used to power this refer to the Aruba Domain Regulatory Table at arubanetworks.com. ANT0, ANT1, and ANT2, and correspond to radio chains 0, 1, and 2. device, as long as it complies with all applicable local regulatory requirements and the DC Verifying Pre-Installation Connectivity For optimal performance when using articulating direct-mount antennas, professional interface meets the following specifications: installers must orient the antennas with ANT0 and ANT2 at 45 degree angles and ANT1 Before you install APs in a network environment, make sure that the APs are able to locate and  12 VDC (+/- 5%)/18W connect to the controller after power on. oriented straight out (see Figure 3).  Center-positive 1.7/4.0 mm circular plug, 9.5 mm length Specifically, you must verify the following conditions: The AP-210 Series requires ArubaOS 6.4.2.0 or later.  When connected to the network, each AP is assigned a valid IP address All Aruba devices with external antennas must be installed by an ACMP qualified Reset Button  APs are able to locate the controller technician using manufacturer-approved antennas only. The ACMP installer(s) is/are ! responsible for ensuring that Equivalent Isotopically Radiated Power (EIRP) levels for all external antenna devices are compliant with the regulatory standards of the host The reset button can be used to return the AP to factory default settings. To reset the AP: 1. Power off the AP. Refer to the ArubaOS Quick Start Guide for instructions on locating and connecting to the controller. Package Contents country/domain. Installer(s) are required to record the antenna gain for this device in system management software. 2. Press and hold the reset button using a small, narrow object, such as a paperclip. 3. Power-on the AP without releasing the reset button. The power LED will flash within 5  AP-214 or AP-215 Access Point seconds. Identifying Specific Installation Locations  9/16" and 15/16” Ceiling Rail Adapters Figure 3 AP-214 Antenna Orientation 4. Release the reset button. You can mount the AP-210 Series access point on a wall or on the ceiling. Use the AP  Installation Guide (this document) The power LED will flash again within 15 seconds indicating that the reset is completed. The placement map generated by Aruba’s Airwave VisualRF Plan software application to determine AP will now continue to boot with the factory default settings. the proper installation location(s). Each location should be as close as possible to the center of Inform your supplier if there are any incorrect, missing, or damaged parts. If the intended coverage area and should be free from obstructions or obvious sources of possible, retain the carton, including the original packing materials. Use these interference. These RF absorbers/reflectors/interference sources will impact RF propagation materials to repack and return the unit to the supplier if needed. Before You Begin and should have been accounted for during the planning phase and adjusted for in VisualRF plan. FCC Statement: Improper termination of access points installed in the United States configured to non-US model controllers will be in violation of the FCC Identifying Known RF Absorbers/Reflectors/Interference AP-210 Series Hardware Overview Figure 1 AP-210 Series LEDs ! grant of equipment authorization. Any such willful or intentional violation may result in a requirement by the FCC for immediate termination of operation and Sources may be subject to forfeiture (47 CFR 1.80). Identifying known RF absorbers, reflectors, and interference sources while in the field during the installation phase is critical. Make sure that these sources are taken into consideration when you attach an AP to its fixed location. Examples of sources that degrade RF performance include: PW R ENET 5Ghz 2.4 Gh z EU Statement:  Cement and brick USB Interface Lower power radio LAN product operating in 2.4 GHz and 5 GHz bands. Please  Objects that contain water The AP-210 Series is equipped with a USB interface for connectivity with cellular modems. refer to the ArubaOS User Guide for details on restrictions.  Metal  Microwave ovens Produit réseau local radio basse puissance operant dans la bande fréquence  Wireless phones and headsets The USB interface is disabled when the AP-210 Series is powered from 802.3af 2.4 GHz et 5 GHz. Merci de vous referrer au ArubaOS User Guide pour les PoE. details des restrictions. LEDs The AP-210 Series is equipped with four LEDs that indicate the status of the various ! Low Power FunkLAN Produkt, das im 2.4 GHz und im 5 GHz Band arbeitet. Installing the AP components of the AP. Figure 4 AP-210 Series Rear Weitere Informationen bezlüglich Einschränkungen finden Sie im ArubaOS User Guide. Service to all Aruba Networks products should be performed by trained service  PWR: Indicates whether or not the AP-210 Series is powered-on personnel only.  ENET: Indicates the status of the AP-210 Series’ Ethernet port  5 GHz: Indicates the status of the 802.11a/n radio Apparati Radio LAN a bassa Potenza, operanti a 2.4 GHz e 5 GHz. Fare riferimento alla ArubaOS User Guide per avere informazioni detagliate sulle  2.4 GHz: Indicates the status of the 802.11b/g/n radio restrizioni. Using the Ceiling Rail Adapter Table 1 AP-210 Series Series LED Meanings The AP-210 Series ships with two ceiling rail adapters for 9/16” and 15/16” ceiling rails. LED Color/State Meaning Pre-Installation Network Requirements Additional wall mount adapters and ceiling rail adapters for other rail styles are available as accessory kits. After WLAN planning is complete and the appropriate products and their placement have been PWR Off No power to AP determined, the Aruba controller(s) must be installed and initial setup performed before the Aruba APs are deployed. Make sure the AP fits securely on the ceiling tile rail when hanging the Green - Flashing Green - Steady AP booting AP ready For initial setup of the controller, refer to the ArubaOS Quick Start Guide for the software version installed on your controller. ! device from the ceiling, because poor installation could cause it to fall onto people or equipment. ENET Off Ethernet link unavailable AP Pre-Installation Checklist Yellow - Steady 10/100Mbps Ethernet link established 1. Pull the necessary cables through a prepared hole in the ceiling tile near where the AP Before installing your AP-210 Series AP, ensure that you have the following: will be placed. Green - Steady 1000Mbps Ethernet link established  CAT5e or better UTP cable of required length 2. Place the adapter against the back of the AP with the adapter at an angle of AP-110_03  One of the following power sources: approximately 30 degrees to the tabs (see Figure 7). Flashing Ethernet link activity  IEEE 802.3at or 802.3af-compliant Power over Ethernet (PoE) source. The POE source 3. Twist the adapter clockwise until it snaps into place in the tabs (see Figure 7). can be any power source equipment (PSE) controller or midspan PSE device 5 GHz Off 5 GHz radio disabled Figure 7 Attaching the Ceiling Rail Adapter  Aruba AP AC-DC adapter kit (sold separately) Yellow - Steady 5 GHz radio enabled in non-HT WLAN mode Console Port  Aruba Controller provisioned on the network:  Layer 2/3 network connectivity to your access point The serial console port allows you to connect the Green - Steady 5 GHz radio enabled in HT WLAN mode Figure 5 Serial Port Pin-Out  One of the following network services: AP to a serial terminal or a laptop for direct local management. This port is an RJ-45 female Serial RJ-45 Female  Aruba Discovery Protocol (ADP) Flashing - Green 5 GHz Air or Spectrum Monitor Console Port Pin-Out  DNS server with an “A” record connector with the pinouts described in . 1 2.4 GHz Off 2.4 GHz radio disabled 2  DHCP Server with vendor-specific options Connect it directly to a terminal or terminal 3 TxD server using an Ethernet cable. 4 GND Yellow - Steady 2.4 GHz radio enabled in non-HT WLAN mode 5 GND 6 RxD 7 Summary of the Setup Process Green - Steady 2.4 GHz radio enabled in HT WLAN mode 8 Direction Successful setup of an AP-210 Series access point consists of five tasks, which must be Input performed in this order: Flashing - Green 2.4 GHz Air or Spectrum Monitor Output Ethernet Port 1. Verify pre-installation connectivity. AP-210 Series is equipped with one 10/100/1000Base-T (RJ-45) auto-sensing, MDI/MDX wired- 2. Identify the specific installation location for each AP. network connectivity port. This port supports IEEE 802.3af and 802.3at Power over Ethernet 3. Install each AP. (PoE) compliance, accepting 48 VDC (nominal) as a standard defined Powered Device (PD) 4. Verify post-installation connectivity. AP-110_04 from a Power Sourcing Equipment (PSE) such as a PoE midspan injector, or network 5. Configure each AP. infrastructure that supports PoE.

4. If necessary, connect the console cable to the console port on the back of the AP. European Union RoHS The Declaration of Conformity made under Directive 1999/5/EC is available for viewing at the 5. Hold the AP next to the ceiling tile rail with the ceiling tile rail mounting slots at following location: http://support.arubanetworks.com approximately a 30-degree angle to the ceiling tile rail (see Figure 8). Make sure that any Aruba products also comply with the EU Restriction of Hazardous cable slack is above the ceiling tile. Substances Directive 2011/65/EC (RoHS). EU RoHS restricts the use of specific hazardous materials in the manufacture of electrical and Canada 6. Pushing toward the ceiling tile, rotate the AP clockwise until the device clicks into place on electronic equipment. Specifically, restricted materials under the RoHS (i)les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont réservés uniquement pour une the ceiling tile rail. Directive are Lead (including Solder used in printed circuit assemblies), Cadmium, Mercury, utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de Figure 8 Mounting the AP Hexavalent Chromium, and Bromine. Some Aruba products are subject to the exemptions listed in satellites mobiles utilisant les mêmes canaux; RoHS Directive Annex 7 (Lead in solder used in printed circuit assemblies). Products and packaging will be marked with the “RoHS” label shown at the left indicating conformance to this Directive. (ii) le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5 250-5 350 MHz et 5 470- 5 725 MHz doit se conformer à la limite de p.i.r.e.; China RoHS (iii) le gain maximal d’antenne permis (pour les dispositifs utilisant la bande 5 725-5 825 MHz) doit se conformer à la limite de p.i.r.e. spécifiée pour l’exploitation point à point et non point à point, selon le AP-210 Series Wireless Aruba products also comply with China environmental declaration requirements cas. 10 and are labeled with the “EFUP 10” label shown at the left. De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les bandes 5 250-5 350 MHz et Access Point ᳝↦᳝ᆇ⠽䋼ໄᯢ Hazardous Materials Declaration ᳝↦᳝ᆇ⠽䋼៪‫ܗ‬㋴(Hazardous Substance) 5 650-5 850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs Installation Guide 䚼ӊৡ⿄ 䪙 ∲ 䬝 ݁Ӌ䫀 ໮⒈㘨㣃 ໮⒈Ѡ㣃䝮 LAN-EL. (Parts) 3E +J &G &U 3%% 3%'( ⬉䏃ᵓ h ƻ ƻ ƻ ƻ ƻ (PCA Boards) ᴎẄ㒘ӊ Aucune émission n’est permise dans la bande 5 600-5 650 MHz. Jusqu’à nouvel avis, les h ƻ ƻ ƻ ƻ ƻ (Mechanical Sub-Assemblies) dispositifs visés par la présente annexe ne doivent pas être en mesure d’émettre dans la bande 5  ƻ˖ 㸼⼎䆹᳝↦᳝ᆇ⠽䋼೼䆹䚼ӊ᠔᳝ഛ䋼ᴤ᭭Ёⱘ৿䞣ഛ೼ SJ/T11363-2006 ᷛ‫ޚ‬㾘ᅮⱘ䰤䞣㽕∖ҹϟDŽ 600-5 650 MHz, afin de protéger les radars météorologiques d’Environnement Canada exploités Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is below the relevant threshold of the SJ/T11363-2006 standard. dans cette bande.  h˖ 㸼⼎䆹᳝↦᳝ᆇ⠽䋼㟇ᇥ೼䆹䚼ӊⱘᶤϔഛ䋼ᴤ᭭Ёⱘ৿䞣䍙ߎ6-7ᷛ‫ޚ‬㾘ᅮⱘ䰤䞣㽕∖DŽ Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials in the parts is above the relevant threshold of the SJ/T11363-2006 standard. AP-110_005  ᇍ䫔ଂП᮹ⱘ᠔ଂѻકᴀ㸼ᰒ⼎կᑨ䫒ⱘ⬉ᄤֵᙃѻકৃ㛑ࣙ৿䖭ѯ⠽䋼DŽ This table shows where these substances may be found in the supply chain of electronic information products, as of the date of sale of the enclosed product. RF Déclaration sur la radioexposition: Cet équipement est conforme aux normes IC Limites ℸᷛᖫЎ䩜ᇍ᠔⍝ঞѻકⱘ⦃ֱՓ⫼ᳳᷛᖫᶤѯ䳊䚼ӊӮ᳝ϔϾϡৠⱘ⦃ֱՓ⫼ᳳ ՟བ⬉∴ऩ‫ܗ‬῵ഫ 䌈೼݊ѻકϞ ℸ⦃ֱՓ⫼ᳳ䰤া䗖⫼Ѣѻકᰃ೼ѻક᠟‫ݠ‬Ё᠔㾘ᅮⱘᴵӊϟᎹ԰ ! d'exposition aux rayonnements RF. Cet équipement doit être installé et utilisé à une distance minimum de 7,9 pouces (20 cm) entre l'radiateur et votre corps pour 2,4 GHz et 5 GHz opérations. cet émetteur ne doit pas être co-localisées ou opérant en conjonction avec une autre antenne ou Contacting Aruba Networks The Environment- Friendly Use Period (EFUP) for all enclosed products and their parts are émetteur. per the symbol shown here. The Environment- Friendly Use Period is valid only when the 7. On the AP-214, install the external antennas according to the manufacturer’s instructions, product is operated under the conditions defined in the product manual. and connect the antennas to the antenna interfaces on the AP. Web Support Operation is subject to the following two conditions: (1) this device may not cause interference, and Main Site http://www.arubanetworks.com Connecting Required Cables (2) this device must accept any interference, including interference that may cause undesired India RoHS operation of the device." Support Site https://support.arubanetworks.com Install cables in accordance with all applicable local and national regulations and practices. This product complies with RoHS requirements as prescribed by E-Waste (Management & Handling) Airheads Social Forums and Knowledge Base community.arubanetworks.com Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio Rules, governed by the Ministry of Environment & Forests, Government of India. exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil nedoit North American Telephone 1-800-943-4526 (Toll Free) pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage Verifying Post-Installation Connectivity radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. 1-408-754-1200 The integrated LEDs on the AP can be used to verify that the AP is receiving power and Safety and Regulatory Compliance International Telephones arubanetworks.com/support-services/aruba-support- "This Class B digital apparatus complies with Canadian ICES-003." program/contact-support/ initializing successfully (see Table 1). Refer to the ArubaOS Quick Start Guide for further Aruba Networks provides a multi-language document that contains country-specific restrictions and details on verifying post-installation network connectivity. additional safety and regulatory information for all Aruba access points. This document can be Software Licensing Site licensing.arubanetworks.com/login.php Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. viewed or downloaded from the following location: www.arubanetworks.com/safety_addendum Wireless Security Incident arubanetworks.com/support/wsirt.php “This device and its antenna(s) must not be co-located or operating in conjunction with any other Response Team (WSIRT) Configuring the AP-210 Series Regulatory Model Names antenna or transmitter.” Support Email Addresses The following regulatory model names apply to the AP-210 Series: Cet appareil et son antenne (s) ne doit pas être co-localisés ou fonctionnant en conjonction avec une AP Provisioning/Reprovisioning  AP-214: APIN0214 autre antenne ou transmetteur. Americas and APAC support@arubanetworks.com Provisioning parameters are unique to each AP. These local AP parameters are initially  AP-215: APIN0215 EMEA emea.support@arubanetworks.com configured on the controller which are then pushed out to the AP and stored on the AP itself. “This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body” Americas and APAC Support Email support@arubanetworks.com Aruba recommends that provisioning settings be configured via the ArubaOS Web UI only. Refer to the ArubaOS User Guide for complete details. FCC WSIRT Email wsirt@arubanetworks.com Cet équipement doit être installé et utilisé à une distance minimale de 20cm entre le radiateur et votre Please email details of any security This device is electronically labeled. To view the FCC ID: corps. problem found in an Aruba product. AP Configuration 1. Log into the controller WebUI. 2. Navigate to Maintenance > Controller > About. “It is the responsibility of the installer to ensure that when using the outdoor antenna kits, only those Configuration parameters are network or controller specific and are configured and stored on antennas certified with the product are used. The use of any antenna other than those certified with the controller. Network configuration settings are pushed out to the AP(s) but remain stored on the product is expressly forbidden by FCC rules 47 CFR part 15.204 and IC RSS standards.” the controller. RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure Copyright Configuration settings can be configured via the ArubaOS Web UI or ArubaOS CLI. Refer to ! limits. This equipment should be installed and operated with a minimum distance of 7.9 inches (20 cm) between the radiator and your body for 2.4 GHz and 5 GHz operations. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Il est de la responsabilité de l'installateur de s'assurer que lorsque vous utilisez les kits d'antennes extérieures, seules les antennes certifiés avec le produit sont utilisés. L'utilisation d'une antenne © 2014 Aruba Networks, Inc. AirWave®, Aruba Networks®, Aruba Mobility Management System®, Bluescanner, For Wireless That Works®, Mobile Edge Architecture, People Move. Networks Must Follow., RFProtect®, The All their respective guides for further details: the ArubaOS User Guide. Wireless Workplace Is Now Open For Business, and The Mobile Edge Company® are trademarks of Aruba autre que ceux qui sont certifiés avec le produit est expressément interdite par la réglementation FCC Networks, Inc. All rights reserved. All other trademarks are the property of their respective owners. partie 47 CFR 15.204 et IC normes RSS. Product Specifications Open Source Code ! When operated in the 5.15 to 5.25 GHz frequency range, this device is restricted to indoor use to reduce the potential for harmful interference with co-channel Mobile Satellite Systems. This radio transmitter 4567A-APIN0214215 has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for Certain Aruba products include Open Source software code developed by third parties, including software code subject to the GNU General Public License ("GPL"), GNU Lesser General Public License ("LGPL"), or other Open Electrical each antenna type indicated. Antenna types not included in this list, having a gain greater than the Source Licenses. The Open Source code used can be found at this site:  Ethernet: maximum gain indicated for that type, are strictly prohibited for use with this device. http://www.arubanetworks.com/open_source  1x 10/100/1000 auto-sensing Ethernet RJ-45 Interface FCC Class B Part 15 The following antenna types have been approved for use with this device:  MDI/MDX AP-ANT-1B; AP-ANT-1W;AP-ANT-13B; AP-ANT-16; AP-ANT-17; AP-ANT-18; Legal Notice This device complies with Part 15 of the Federal Communications Commission (FCC) Rules.  IEEE 802.3 (10Base-T), IEEE 802.3u (100Base-T). IEEE 802.3ab (1000Base-T) The use of Aruba Networks, Inc. switching platforms and software, by all individuals or corporations, to terminate Operation is subject to the following two conditions: AP-ANT-19; AP-ANT-20 other vendors' VPN client devices constitutes complete acceptance of liability by that individual or corporation for  Power over Ethernet (IEEE 802.3at and 802.3af compliant), 48V DC (nominal) and 56V DC this action and indemnifies, in full, Aruba Networks, Inc. from any and all legal actions that might be taken against (maximum)/350mA (see Figure 6 for pin configuration) 1. This device may not cause harmful interference. The Maximum permissible antenna gain is 7.5dBi and the antenna impedance is 50 ohms. it with respect to infringement of copyright on behalf of those vendors.  Power: 2. This device must accept any interference received, including interference that may cause  12 VDC power interface, supports powering through an AC-to-DC power adapter undesired operation. Singapore Warranty  POE support on Ethernet ports: 802.3at-compliant and 802.3af-compliant POE sourcing This hardware product is protected by an Aruba warranty. For details, see Aruba Networks standard warranty devices If a power adapter other than the one provided by Aruba Networks is used in the US or Canada, ! Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. DB101525 terms and conditions. it should be cULus (NRTL) Listed, with an output rated 12 VDC, minimum 1.5A, marked “LPS” or “Class 2,” and suitable for plugging into a standard power receptacle in the US and Canada. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. This equipment generates, uses and can radiate radio frequency Medical energy and, if not installed and used in accordance with the manufacturer’s instructions, may cause 1. Equipment not suitable for use in the presence of flammable mixtures. Environmental interference harmful to radio communications. 2. Connect to only IEC 60950-1 or IEC 60601-1 3rd edition certified products and power sources.  Operating: If this equipment does cause interference, which can be determined by turning the equipment off and The end user is responsible for the resulting medical system complies with the requirements of  Temperature: 0° C to +50° C (+32° F to +122° F) on, the user is encouraged to try to correct the interference by one or more of the following measures: IEC 60601-1 3rd edition.  Humidity: 5% to 95% non-condensing  Reorient or relocate the receiving antenna. 3. Wipe with a dry cloth, no additional maintenance required.  Storage and transportation:  Increase the separation between the equipment and receiver. 4. No serviceable parts, the unit must be sent back to the manufacturer for repair.  Temperature: -40° C to +70° C (-40° F to +158° F)  Connect the equipment to an outlet on a circuit different from that to which the receiver is 5. No modifications are allowed without Aruba approval. For additional specifications on this product, please refer to the data sheet. The data sheet can be connected. found at www.arubanetworks.com.  Consult the dealer or an experienced radio or TV technician for help. 第十二條 Complies with the Class B limits for radio noise emissions as set out in the interference-causing 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大 equipment standard entitled “Digital Apparatus,” ICES-003 of Industry Canada. 功率或變更原設計之特性及功能。 Proper Disposal of Aruba Equipment Cet apareil numerique de la classe B respecte toutes les exigencies du Reglement sur le materiel 第十四條 Dispose of Aruba products per local regulations. For the most current information about Global brouilleur du Canada. 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有 Environmental Compliance and Aruba products, see our website at www.arubanetworks.com. Users are advised that high power Radars are allocated as primary users of the bands 5250-5350 MHz 干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。 and 5650-5850 MHz and these Radars could cause interference and/or damage to Licensed Exempt WLAN devices. 前項合法通信，指依電信法規定作業之無線電通信。 Waste of Electrical and Electronic Equipment 低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電 www.arubanetworks.com Aruba products at end of life are subject to separate collection and treatment in the EU Member States, Norway, and Switzerland and therefore are marked EU Regulatory Conformance 機設備之干擾。 1344 Crossman Avenue Sunnyvale, California 94089 with the symbol shown at the left (crossed-out wheelie bin). The treatment This product is CE marked according to the provisions of the R & TTE Directive Phone: 408.227.4500 applied at end of life of these products in these countries shall comply with Fax 408.227.4550 (1999/5/EC) - CE(!). Aruba Networks Inc., hereby declares that the APIN0114 / Expected Service Life 10 years. the applicable national laws of countries implementing Directive 2002/96EC APIN0115 device models are in compliance with the essential requirements and other relevant on Waste of Electrical and Electronic Equipment (WEEE). provisions of Directive 1999/5/EC -CE(!) AP-210 Series Wireless Access Point | Installation Guide Part Number 0511513-04 | Febuary 2015


Document Created: 2015-04-20 16:16:51
Document Modified: 2015-04-20 16:16:51
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC