User Manual

FCC ID: Q9DAPIN0207

Users Manual

Download: PDF
FCCID_3138394

 Blink mode: Both LEDs blink green (synchronized) Figure 1 LEDs System Status Radio Status Aruba 207 Series Wireless Access Point Installation Guide Table 1 207 Series LEDs Status in Normal Mode LED Color/State Meaning System Off Device powered off Status (Left) Green- Device booting, not ready for use Blinking a Hewlett Packard Enterprise company Green- Solid Device ready for use, no restrictions Green- Device ready for use, uplink negotiated Package Contents Flashing in sub optimal speed (<1Gbps)  (I)AP-207 access point  9/16” and 15/16” Ceiling Rail Adapter (spare: AP-220-MNT- Red- Solid System error condition C1) Radio Off Device powered off, or both radios  Regulatory Compliance and Safety Information Guide Status disabled  Instant Quick Start Guide (for IAP-207 only) (Right) Green- Solid Both radios enabled in access mode  Professional Install Guide (for IAP-207 only)  Installation Guide (this document). Green- One radio enabled in access mode Blinking This device must be professionally installed and Amber- Solid Both radios enabled in monitor mode serviced by a trained ACMP or similar Aruba-certified technician. Aruba access points are classified as radio Amber- One radio enabled in monitor mode transmission devices, and are subject to government Blinking regulations of the host country. The network Alternating  Green: one radio in access mode administrator(s) is/are responsible for ensuring that  Amber: one radio in monitor mode configuration and operation of this equipment is in compliance with their country’s regulations. For complete list of approved channels in your country, Figure 2 Back Panel refer to the Aruba Downloadable Regulatory Table at Ethernet Port support.arubanetworks.com. DC Power Socket 12V 1A ENET Console Port 56V 350mA CONSOLE Reset Button Access points are radio transmission devices and are subject to governmental regulation. Network administrators responsible for the configuration and operation of access points must comply with local broadcast regulations. Specifically, access points must Kensington use channel assignments appropriate to the location in Lock Slot which the access point will be used. 207 Series Hardware Overview Console Port The serial console port is located at the back of the (I)AP-207 LEDs and is a 4-pin connector covered by a dust cover. An optional The 207 Series access points have two LEDs that indicate the serial adapter cable (AP-CBL-SER) is sold separately to system and radio status of the device. These two LEDs can be connect the (I)AP to a serial terminal or a laptop for direct configured via ArubaOS (for AP-207) or Aruba Instant (for local management. IAP-207) software into three separate modes:  Normal mode (by default): See Table 1 Ethernet Port  Both LEDs off The 207 Series access points are equipped with one 10/100/ 1000Base-T (RJ-45) auto-sensing, MDI/MDX Ethernet port 0511875-02 | April 2016 1

(ENET0) for wired network connectivity. This port supports The 207 Series access points ship with two ceiling rail IEEE 802.3af Power over Ethernet (PoE), as a standard adapters for 9/16” and 15/16” ceiling rails. Additional ceiling defined Powered Device (PD) from a Power Sourcing rail adapters for other rail styles and wall mount adapters are Equipment (PSE) such as a PoE midspan injector or network available as accessory kits. infrastructure that supports PoE. 1. Pull the necessary cables through a prepared hole in the Reset Button ceiling tile near where the access point will be placed. To reset the 207 Series access points to factory default 2. Place the adapter against the back of the access point settings, press and hold down the reset button using a small, with the adapter at an angle of approximately 30 degrees narrow object such as a paper clip while the (I)AP is powered to the tabs (see Figure 3). on. 3. Twist the adapter clockwise until it snaps into place in the tabs (see Figure 3). DC Power Socket Figure 3 Attaching the Ceiling Rail Adapter If PoE is not available, an optional Aruba AP-AC-12V30B power adapter kit (sold separately) can be used to power the 207 Series access points. Additionally, a locally-sourced AC-to-DC adapter (or any DC source) can be used to power this device, as long as it complies with all applicable local regulatory requirements and the DC interface meets the following specifications:  12 Vdc (+/- 5%) and at least 12W  Center-positive 2.1/5.5 mm circular plug, 9.5 mm length FCC Statement: Improper termination of access points installed in the United States configured to non- US model controllers will be in violation of the FCC 4. Hold the access point next to the ceiling tile rail with the grant of equipment authorization. Any such willful or ceiling tile rail mounting slots at approximately a 30- intentional violation may result in a requirement by degree angle to the ceiling tile rail (see Figure 4). Make the FCC for immediate termination of operation and sure that any cable slack is above the ceiling tile. may be subject to forfeiture (47 CFR 1.80). 5. Pushing toward the ceiling tile, rotate the access point clockwise until the device clicks into place on the ceiling tile rail. EU Statement: Figure 4 Mounting the Access Point Lower power radio LAN product operating in 2.4 GHz and 5 GHz bands. Please refer to the ArubaOS User Guide/Aruba Instant User Guide for details on restrictions. Produit réseau local radio basse puissance operant dans la bande fréquence 2.4 GHz et 5 GHz. Merci de vous referrer au ArubaOS User Guide/Aruba Instant User Guide pour les details des restrictions. Low Power FunkLAN Produkt, das im 2.4 GHz und im 5 GHz Band arbeitet. Weitere Informationen bezlüglich Einschränkungen finden Sie im ArubaOS User Guide/ Aruba Instant User Guide. Apparati Radio LAN a bassa Potenza, operanti a 2.4 GHz e 5 GHz. Fare riferimento alla ArubaOS User Guide/ Aruba Instant User Guide per avere informazioni detagliate sulle restrizioni. Connecting Required Cables Install cables in accordance with all applicable local and Installing the Access Point national regulations and practices. For additional information, refer to the online version of the Service to all Aruba Networks products should be Aruba 207 Series Wireless Access Point Installation Guide at performed by an AMCP certified technician or similar. support.arubanetworks.com or scan the QR code. The installer is responsible for securing the access point onto the ceiling tile rail in accordance with the steps below. Failure to properly install this product may result in physical injury and/or damage to property. 2 Aruba 207 Series Wireless Access Point | Installation Guide


Document Created: 2017-12-14 21:23:12
Document Modified: 2017-12-14 21:23:12
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC