Operator Manual

FCC ID: Q9DAPIN0114115

Users Manual

Download: PDF
FCCID_2036412

AP-110 Series Wireless Access Point Installation Guide The Aruba AP-114 and AP-115 wireless access points support the IEEE 802.11n Figure 2 AP-110 Series Side (AP-114 shown) Figure 5 Gigabit Ethernet Port Pin-Out Summary of the Setup Process standard for high-performance WLAN. These access points use MIMO (Multiple- ANT0 ANT1 ANT2 1000Base-T Gigabit RJ-45 Female Signal Name Function Successful setup of an AP-110 Series access point consists of five tasks, which in, Multiple-out) technology and other high-throughput mode techniques to Ethernet Port Pin-Out 1 BI_DA+ Bi-directional pair +A must be performed in this order: deliver high-performance, 802.11n 2.4 GHz and 5 GHz functionality while BI_DA- 2 Bi-directional pair -A simultaneously supporting existing 802.11a/b/g wireless services. The AP-110 3 BI_DB+ Bi-directional pair +B 1. Verify pre-installation connectivity. Series access points work only in conjunction with an Aruba Controller. 4 BI_DC+ Bi-directional pair +C 5 BI_DC- Bi-directional pair -C 2. Identify the specific installation location for each AP. The Aruba AP-110 Series access point provides the following capabilities: 6 BI_DB- Bi-directional pair -B 7 BI_DD+ Bi-directional pair +D 3. Install each AP.  Wireless transceiver 8 BI_DD- Bi-directional pair -D 4. Verify post-installation connectivity.  Protocol-independent networking functionality 5. Configure each AP.  IEEE 802.11a/b/g/n operation as a wireless access point DC Power Socket  IEEE 802.11a/b/g/n operation as a wireless air monitor If PoE is not available, an optional Aruba AP AC-DC adapter kit (sold separately)  Compatibility with IEEE 802.3at PoE+ and 802.3af PoE can be used to power the AP-110 Series. Aruba Networks, Inc., in compliance with governmental requirements, has  Central management configuration and upgrades through a controller USB Port designed the AP-110 Series access points so that only authorized network Additionally, a locally-sourced AC-to-DC adapter (or any DC source) can be used to power this device, as long as it complies with all applicable local regulatory administrators can change the settings. For more information about AP External Antenna Connectors requirements and the DC interface meets the following specifications: configuration, refer to the ArubaOS Quick Start Guide and ArubaOS User The AP-110 Series requires ArubaOS 6.3.1.0 or later. Guide. The AP-114 is equipped with three external antenna connectors. The connectors  12 VDC (+/- 5%)/18W are labeled ANT0, ANT1, and ANT2, and correspond to radio chains 0, 1, and 2.  Center-positive 1.7/4.0 mm circular plug, 9.5 mm length Access points are radio transmission devices and as such are subject to Package Contents USB Interface Reset Button governmental regulation. Network administrators responsible for the   AP-114 or AP-115 access point 9/16" and 15/16” Ceiling Rail Adapters The AP-110 Series is equipped with a USB interface for connectivity with cellular modems. The reset button can be used to return the AP to factory default settings. To reset the AP: ! configuration and operation of access points must comply with local broadcast regulations. Specifically, access points must use channel assignments appropriate to the location in which the access point will be  Installation guide (this document) 1. Power off the AP. used. The USB interface is disabled when the AP-110 Series is powered from 802.3af PoE. 2. Press and hold the reset button using a small, narrow object, such as a Inform your supplier if there are any incorrect, missing, or damaged parts. If paperclip. possible, retain the carton, including the original packing materials. Use 3. Power-on the AP without releasing the reset button. The power LED will Verifying Pre-Installation Connectivity these materials to repack and return the unit to the supplier if needed. Figure 3 AP-110 Series Rear flash within 5 seconds. Before you install APs in a network environment, make sure that the APs are able to locate and connect to the controller after power on. 4. Release the reset button. Specifically, you must verify the following conditions: AP-110 Series Hardware Overview The power LED will flash again within 15 seconds indicating that the reset is completed. The AP will now continue to boot with the factory default settings.  When connected to the network, each AP is assigned a valid IP address Figure 1 AP-110 Series LEDs  APs are able to locate the controller Before You Begin Refer to the ArubaOS Quick Start Guide for instructions on locating and connecting to the controller. FCC Statement: Improper termination of access points installed in the PW R ENET 5Ghz 2.4 Gh z United States configured to non-US model controllers will be in violation of Identifying Specific Installation Locations ! the FCC grant of equipment authorization. Any such willful or intentional violation may result in a requirement by the FCC for immediate termination You can mount the AP-110 Series access point on a wall or on the ceiling. Use the of operation and may be subject to forfeiture (47 CFR 1.80). AP placement map generated by Aruba’s Airwave VisualRF Plan software application to determine the proper installation location(s). Each location should be as close as possible to the center of the intended coverage area and LEDs EU Statement: should be free from obstructions or obvious sources of interference. These RF The AP-110 Series is equipped with four LEDs that indicate the status of the Lower power radio LAN product operating in 2.4 GHz and 5 GHz bands. absorbers/reflectors/interference sources will impact RF propagation and various components of the AP. Please refer to the ArubaOS User Guide for details on restrictions. should have been accounted for during the planning phase and adjusted for in VisualRF plan.  PWR: Indicates whether or not the AP-110 Series is powered-on Produit réseau local radio basse puissance operant dans la bande  ENET: Indicates the status of the AP-110 Series’ Ethernet port fréquence 2.4 GHz et 5 GHz. Merci de vous referrer au ArubaOS User Identifying Known RF Absorbers/Reflectors/Interference 5 GHz: Indicates the status of the 802.11a/n radio Guide pour les details des restrictions. Sources   2.4 GHz: Indicates the status of the 802.11b/g/n radio ! Low Power FunkLAN Produkt, das im 2.4 GHz und im 5 GHz Band arbeitet. Identifying known RF absorbers, reflectors, and interference sources while in Weitere Informationen bezlüglich Einschränkungen finden Sie im ArubaOS the field during the installation phase is critical. Make sure that these sources are Table 1 AP-110 Series Series LED Meanings User Guide. taken into consideration when you attach an AP to its fixed location. Examples LED Color/State Meaning of sources that degrade RF performance include: Apparati Radio LAN a bassa Potenza, operanti a 2.4 GHz e 5 GHz. Fare riferimento alla ArubaOS User Guide per avere informazioni detagliate sulle  Cement and brick PWR Off No power to AP Console Port restrizioni.  Objects that contain water Red Initial power-up The serial console port allows you to connect the AP to a serial terminal or a  Metal laptop for direct local management. This port is an RJ-45 female connector with  Microwave ovens Green - Flashing AP booting the pinouts described in Figure 4. Connect it directly to a terminal or terminal Pre-Installation Network Requirements  Wireless phones and headsets Green - Steady AP ready server using an Ethernet cable. After WLAN planning is complete and the appropriate products and their placement have been determined, the Aruba controller(s) must be installed and ENET Off Ethernet link unavailable Figure 4 Serial Port Pin-Out initial setup performed before the Aruba APs are deployed. Installing the AP Serial RJ-45 Female Yellow - Steady 10/100Mbps Ethernet link established Console Port Pin-Out For initial setup of the controller, refer to the ArubaOS Quick Start Guide for 1 Service to all Aruba Networks products should be performed by trained 2 the software version installed on your controller. Green - Steady 1000Mbps Ethernet link established 3 TxD service personnel only. 4 GND Flashing Ethernet link activity 5 GND AP Pre-Installation Checklist 6 RxD 7 5 GHz Off 5 GHz radio disabled 8 Before installing your AP-110 Series AP, ensure that you have the following: Using the Ceiling Rail Adapter Direction Yellow - Steady 5 Ghz radio enabled in non-HT WLAN mode Input  CAT5e or better UTP cable of required length The AP-110 Series ships with two ceiling rail adapters for 9/16” and 15/16” ceiling Output  One of the following power sources: Green - Steady 5 Ghz radio enabled in HT WLAN mode rails. Additional wall mount adapters and ceiling rail adapters for other rail  IEEE 802.3at or 802.3af-compliant Power over Ethernet (PoE) source. The styles are available as accessory kits. Flashing - Green 5 Ghz Air or Spectrum Monitor Ethernet Port POE source can be any power source equipment (PSE) controller or AP-110 Series is equipped with one 10/100/1000Base-T (RJ-45) auto-sensing, midspan PSE device Make sure the AP fits securely on the ceiling tile rail when hanging 2.4 GHz Off 2.4 GHz radio disabled Yellow - Steady 2.4 Ghz radio enabled in non-HT WLAN MDI/MDX wired-network connectivity port. This port supports IEEE 802.3af and 802.3at Power over Ethernet (PoE) compliance, accepting 48 VDC (nominal) as a   Aruba AP AC-DC adapter kit (sold separately) Aruba Controller provisioned on the network: ! the device from the ceiling, because poor installation could cause it to fall onto people or equipment. mode standard defined Powered Device (PD) from a Power Sourcing Equipment (PSE)  Layer 2/3 network connectivity to your access point such as a PoE midspan injector, or network infrastructure that supports PoE. Green - Steady 2.4 Ghz radio enabled in HT WLAN mode  One of the following network services: The 10/100/1000 Mbps Ethernet ports are on the bottom of the AP. These ports 1. Pull the necessary cables through a prepared hole in the ceiling tile near Flashing - Green 2.4 Ghz Air or Spectrum Monitor  Aruba Discovery Protocol (ADP) have RJ-45 female connectors with the pin-outs shown in Figure 5. where the AP will be placed.  DNS server with an “A” record 2. Place the adapter against the back of the AP with the adapter at an angle of  DHCP Server with vendor-specific options approximately 30 degrees to the tabs (see Figure 6).

3. Twist the adapter clockwise until it snaps into place in the tabs (see Figure 6).  Power: 2. This device must accept any interference received, including interference that may cause  12 VDC power interface, supports powering through an AC-to-DC power adapter undesired operation. Figure 6 Attaching the Ceiling Rail Adapter  POE support on Ethernet ports: 802.3at-compliant and 802.3af-compliant POE sourcing devices Changes or modifications to this unit not expressly approved by the party If a power adapter other than the one provided by Aruba Networks is used ! responsible for compliance could void the user’s authority to operate this equipment. in the US or Canada, it should be cULus (NRTL) Listed, with an output rated 12 VDC, minimum 1.25A, marked “LPS” or “Class 2,” and suitable for plugging into a standard power receptacle in the US and Canada. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. This equipment generates, uses and can radiate radio frequency For additional specifications on this product, please refer to the data sheet. The data sheet can be energy and, if not installed and used in accordance with the manufacturer’s instructions, may cause interference harmful to radio communications. AP-110 Series Wireless Access Point found at www.arubanetworks.com. If this equipment does cause interference, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna. Proper Disposal of Aruba Equipment For the most current information about Global Environmental Compliance and Aruba products, see   Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is Installation Guide our website at www.arubanetworks.com. connected.  Consult the dealer or an experienced radio or TV technician for help. Waste of Electrical and Electronic Equipment Complies with the Class B limits for radio noise emissions as set out in the interference-causing AP-110_04 equipment standard entitled “Digital Apparatus,” ICES-003 of Industry Canada. Aruba products at end of life are subject to separate collection and treatment Cet apareil numerique de la classe B respecte toutes les exigencies du Reglement sur le materiel in the EU Member States, Norway, and Switzerland and therefore are marked brouilleur du Canada. with the symbol shown at the left (crossed-out wheelie bin). The treatment applied at end of life of these products in these countries shall comply with 4. If necessary, connect the console cable to the console port on the back of the the applicable national laws of countries implementing Directive 2002/96EC EU Regulatory Conformance on Waste of Electrical and Electronic Equipment (WEEE). AP. This product is CE marked according to the provisions of the R & TTE Directive Contacting Aruba Networks (1999/5/EC) - CE(!). Aruba Networks Inc., hereby declares that the APIN0114 / 5. Hold the AP next to the ceiling tile rail with the ceiling tile rail mounting slots European Union RoHS APIN0115 device models are in compliance with the essential requirements and other relevant Table 1 at approximately a 30-degree angle to the ceiling tile rail (see Figure 7). Make Aruba products also comply with the EU Restriction of Hazardous provisions of Directive 1999/5/EC -CE(!) sure that any cable slack is above the ceiling tile. Substances Directive 2011/65/EC (RoHS). EU RoHS restricts the use of The Declaration of Conformity made under Directive 1999/5/EC is available for viewing at the Web Site Support specific hazardous materials in the manufacture of electrical and following location: http://support.arubanetworks.com 6. Pushing toward the ceiling tile, rotate the AP clockwise until the device clicks electronic equipment. Specifically, restricted materials under the RoHS Main Site http://www.arubanetworks.com into place on the ceiling tile rail. Directive are Lead (including Solder used in printed circuit assemblies), Cadmium, Mercury, Hexavalent Chromium, and Bromine. Some Aruba products are subject to the exemptions listed in Support Site https://support.arubanetworks.com Figure 7 Mounting the AP RoHS Directive Annex 7 (Lead in solder used in printed circuit assemblies). Products and packaging Software Licensing Site https://licensing.arubanetworks.com/login.php will be marked with the “RoHS” label shown at the left indicating conformance to this Directive. Wireless Security Incident http://www.arubanetworks.com/support/wsirt.php Response Team (WSIRT) China RoHS Americas and APAC Support Email support@arubanetworks.com Aruba products also comply with China environmental declaration requirements and are labeled with the “EFUP 10” label shown at the left. EMEA Support Email emea.support@arubanetworks.com 10 ᳝↦᳝ᆇ⠽䋼ໄᯢ WSIRT Email wsirt@arubanetworks.com Please email details of any security Hazardous Materials Declaration problem found in an Aruba product. ᳝↦᳝ᆇ⠽䋼៪‫ܗ‬㋴(Hazardous Substance) 䚼ӊৡ⿄ 䪙 ∲ 䬝 ݁Ӌ䫀 ໮⒈㘨㣃 ໮⒈Ѡ㣃䝮 (Parts) 3E +J &G &U 3%% 3%'( ⬉䏃ᵓ (PCA Boards) h ƻ ƻ ƻ ƻ ƻ Table 2 ᴎẄ㒘ӊ h ƻ ƻ ƻ ƻ ƻ (Mechanical Sub-Assemblies)  ƻ˖ 㸼⼎䆹᳝↦᳝ᆇ⠽䋼೼䆹䚼ӊ᠔᳝ഛ䋼ᴤ᭭Ёⱘ৿䞣ഛ೼ SJ/T11363-2006 ᷛ‫ޚ‬㾘ᅮⱘ䰤䞣㽕∖ҹϟDŽ Telephone Support Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is below the relevant threshold of the SJ/T11363-2006 standard.  h˖ 㸼⼎䆹᳝↦᳝ᆇ⠽䋼㟇ᇥ೼䆹䚼ӊⱘᶤϔഛ䋼ᴤ᭭Ёⱘ৿䞣䍙ߎ6-7ᷛ‫ޚ‬㾘ᅮⱘ䰤䞣㽕∖DŽ Aruba Corporate +1 (408) 227-4500 Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials in the parts is above the relevant threshold of the SJ/T11363-2006 standard.  FAX +1 (408) 227-4550 ᇍ䫔ଂП᮹ⱘ᠔ଂѻકᴀ㸼ᰒ⼎կᑨ䫒ⱘ⬉ᄤֵᙃѻકৃ㛑ࣙ৿䖭ѯ⠽䋼DŽ AP-110_005 This table shows where these substances may be found in the supply chain of electronic information products, as of the date of sale of the enclosed product. ℸᷛᖫЎ䩜ᇍ᠔⍝ঞѻકⱘ⦃ֱՓ⫼ᳳᷛᖫᶤѯ䳊䚼ӊӮ᳝ϔϾϡৠⱘ⦃ֱՓ⫼ᳳ ՟བ⬉∴ऩ‫ܗ‬῵ഫ 䌈೼݊ѻકϞ Copyright ℸ⦃ֱՓ⫼ᳳ䰤া䗖⫼Ѣѻકᰃ೼ѻક᠟‫ݠ‬Ё᠔㾘ᅮⱘᴵӊϟᎹ԰ © 2013 Aruba Networks, Inc. AirWave®, Aruba Networks®, Aruba Mobility Management System®, Bluescanner, The Environment- Friendly Use Period (EFUP) for all enclosed products and their parts are per the symbol shown here. The Environment- Friendly Use Period is valid only when the product is operated under the conditions defined in the product manual. For Wireless That Works®, Mobile Edge Architecture, People Move. Networks Must Follow., RFProtect®, The All 7. On the AP-114, install the external antennas according to the manufacturer’s Wireless Workplace Is Now Open For Business, and The Mobile Edge Company® are trademarks of Aruba Networks, Inc. All rights reserved. All other trademarks are the property of their respective owners. instructions, and connect the antennas to the antenna interfaces on the AP. Open Source Code Connecting Required Cables Safety and Regulatory Compliance Certain Aruba products include Open Source software code developed by third parties, including software code subject to the GNU General Public License ("GPL"), GNU Lesser General Public License ("LGPL"), or other Open Install cables in accordance with all applicable local and national regulations and Aruba Networks provides a multi-language document that contains country-specific restrictions and Source Licenses. The Open Source code used can be found at this site: practices. additional safety and regulatory information for all Aruba access points. This document can be http://www.arubanetworks.com/open_source viewed or downloaded from the following location: www.arubanetworks.com/safety_addendum Legal Notice Regulatory Model Names Verifying Post-Installation Connectivity The use of Aruba Networks, Inc. switching platforms and software, by all individuals or corporations, to terminate other vendors' VPN client devices constitutes complete acceptance of liability by that individual or corporation for The following regulatory model names apply to the AP-110 Series: this action and indemnifies, in full, Aruba Networks, Inc. from any and all legal actions that might be taken against The integrated LEDs on the AP can be used to verify that the AP is receiving it with respect to infringement of copyright on behalf of those vendors.  AP-114: APIN0114 power and initializing successfully (see Table 1). Refer to the ArubaOS Quick  AP-115: APIN0115 Start Guide for further details on verifying post-installation network Warranty connectivity. This hardware product is protected by the standard Aruba warranty of one year parts/labor. For more information, FCC refer to the ARUBACARE SERVICE AND SUPPORT TERMS AND CONDITIONS. Altering this device (such as painting it) voids the warranty. This device is electronically labeled. To view the FCC ID: Configuring the AP-110 Series 1. Log into the controller WebUI. 2. Navigate to Maintenance > Controller > About. AP Provisioning/Reprovisioning Provisioning parameters are unique to each AP. These local AP parameters are RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits. This equipment should be installed and initially configured on the controller which are then pushed out to the AP and operated with a minimum distance of 7.9 inches (20 cm) between the stored on the AP itself. Aruba recommends that provisioning settings be configured via the ArubaOS Web UI only. Refer to the ArubaOS User Guide for complete details. ! radiator and your body for 2.4 GHz and 5 GHz operations. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. When operated in the 5.15 to 5.25 GHz frequency range, this device is restricted to indoor use to reduce the potential for harmful AP Configuration interference with co-channel Mobile Satellite Systems. Configuration parameters are network or controller specific and are configured and stored on the controller. Network configuration settings are pushed out to the AP(s) but remain stored on the controller. Users are advised that high power Radars are allocated as primary users of Configuration settings can be configured via the ArubaOS Web UI or ArubaOS ! the bands 5250-5350 MHz and 5650-5850 MHz and these Radars could cause interference and/or damage to Licensed Exempt WLAN devices. CLI. Refer to their respective guides for further details: the ArubaOS User Guide. Product Specifications FCC Class B Part 15 This device complies with Part 15 of the Federal Communications Commission (FCC) Rules. Operation is subject to the following two conditions: www.arubanetworks.com Electrical 1344 Crossman Avenue 1. This device may not cause harmful interference. Sunnyvale, California 94089  Ethernet: Phone: 408.227.4500  1x 10/100/1000Base-T auto-sensing Ethernet RJ-45 Interface Fax 408.227.4550  MDI/MDX  IEEE 802.3 (10Base-T), IEEE 802.3u (100Base-T). IEEE 802.3ab (1000Base-T) AP-110 Series Wireless Access Point | Installation Guide Part Number 0511365-02 | August 2013  Power over Ethernet (IEEE 802.3at and 802.3af compliant), 48V DC (nominal) and 56V DC (maximum)/350mA (see Figure 5 for pin configuration)


Document Created: 2013-08-01 14:45:59
Document Modified: 2013-08-01 14:45:59
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC