Users Manual

FCC ID: Q9D651

Users Manual

Download: PDF
FCCID_1111422

E CONSOL 7 LINK/ 6 ACT 5 LINK/ ACT LINK/ ACT 4 1000 3 2 1 LINK/ ACT 0 POE Aruba 650 Series Controller Installation Guide

Copyright © 2009 Aruba Networks, Inc. All rights reserved. Trademarks Aruba Networks® is a registered trademark, and Mobility Management System, RFprotect®, and Bluescanner are trademarks of Aruba Networks, Inc. All other trademarks or registered trademarks are the property of their respective holders. Specifications are subject to change without notice. Legal Notice The use of Aruba Networks, Inc. switching platforms and software, by all individuals or corporations, to terminate other vendors' VPN client devices constitutes complete acceptance of liability by that individual or corporation for this action and indemnifies, in full, Aruba Networks, Inc. from any and all legal actions that might be taken against it with respect to infringement of copyright on behalf of those vendors. Warranty This hardware product is protected by the standard Aruba warranty of one year parts/labor. For more information, refer to the ARUBACARE SERVICE AND SUPPORT TERMS AND CONDITIONS. Altering this device (such as painting it) voids the warranty. www.arubanetworks.com 1322 Crossman Avenue Sunnyvale, California 94089 Phone: 408.227.4500 Fax 408.227.4550 May 2009 | 0510572-01 Aruba 650 Series Multi-Service Mobility Controller | Installation Guide

Contents Preface...................................................................................................... 5 General Overview ..................................................................................................5 Related Documentation .........................................................................................5 Contacting Aruba Networks ..................................................................................6 Chapter 1 Aruba 650 Series Hardware Overview ................................................... 7 About the Aruba 650 Series Controller..................................................................7 Minimum Software Requirements .........................................................................7 Package Checklist .................................................................................................7 Hardware Model Overview ....................................................................................8 Front View .......................................................................................................8 1000Base-X (SFP) Ports ...........................................................................8 10/100/1000Base-T Gigabit Ethernet Ports .............................................8 Serial Console Port...................................................................................9 Serial Console Port Adaptor ...................................................................10 USB Ports ...............................................................................................10 Media Eject Button .................................................................................10 Rear View ......................................................................................................11 AC Power Socket ...................................................................................11 ExpressCard Slot....................................................................................11 Antennae Interfaces (Aruba 651 Only) ....................................................11 LED Status Indicators..........................................................................................11 Chapter 2 Aruba 650 Series Installation ................................................................ 13 Installation ...........................................................................................................13 Pre-Installation Requirements.......................................................................13 Physical Installation.......................................................................................13 Rack Mounting .......................................................................................13 Tabletop Deployment .............................................................................15 Initial Setup and Network Connectivity.........................................................15 Removal...............................................................................................................15 Appendix A Specifications, Safety, & Compliance.................................................. 17 Specifications ......................................................................................................17 Physical Specifications .................................................................................17 Power Specifications ....................................................................................17 Operating Specifications...............................................................................17 Storage Specifications ..................................................................................17 Wireless Radio Specifications (651 Internal AP) ...........................................17 AP type ...................................................................................................17 Operating Frequency ..............................................................................17 Available Channels .................................................................................17 Modulations ............................................................................................17 Transmit Power.......................................................................................18 Association Rates (Mbps).......................................................................18 802.11n High-Throughput (HT) Support.................................................18 802.11n Packet Aggregation ..................................................................18 Antenna (Aruba 651 Internal AP) ...................................................................18 Aruba 650 Series Multi-Service Mobility Controller | Installation Guide Contents | 3

Safety and Regulatory Compliance .....................................................................19 FCC Class B Device......................................................................................19 Aruba 650......................................................................................................19 Aruba 651......................................................................................................19 Proper Disposal of Aruba Equipment ..................................................................20 Waste of Electrical and Electronic Equipment ..............................................20 European Union RoHS ..................................................................................20 China RoHS ..................................................................................................20 4 | Contents Aruba 650 Series Multi-Service Mobility Controller | Installation Guide

Preface This preface includes the following information: z An overview of the contents of this manual z A list of related documentation for further reading z Aruba support and service information General Overview z Chapter 1, “Aruba 650 Series Hardware Overview” on page 7 provides a detailed hardware overview of the Aruba 650 Series. z Chapter 2, “Aruba 650 Series Installation” on page 13 provides rack mounting and installation instructions. z Appendix A, “Specifications, Safety, & Compliance” on page 17 includes product technical specifications, safety, and regulatory compliance information. Related Documentation The following documentation are referred to in this guide and are considered components of the complete documentation set needed for a successful installation and management of an Aruba Mobility Controller. z ArubaOS Quick Start Guide z ArubaOS User Guide z Aruba Mobility Management System User Guide Aruba 650 Series Multi-Service Mobility Controller | Installation Guide Preface | 5

Contacting Aruba Networks Web Site Support Main Site http://www.arubanetworks.com Support Site https://support.arubanetworks.com Software Licensing Site https://licensing.arubanetworks.com/login.php Wireless Security Incident http://www.arubanetworks.com/support/wsirt.php Response Team (WSIRT) Support Emails z Americas and APAC support@arubanetworks.com z EMEA emea_support@arubanetworks.com WSIRT Email wsirt@arubanetworks.com Please email details of any security problem found in an Aruba product. Telephone Support Aruba Corporate +1 (408) 227-4500 FAX +1 (408) 227-4550 Support z United States 800-WI-FI-LAN (800-943-4526) z Universal Free Phone Service Number +800-4WIFI-LAN (+800-49434-526) (UIFN): Australia, Canada, China, France, Germany, Hong Kong, Ireland, Israel, Japan, Korea, Singapore, South Africa, Taiwan, and the UK. z All Other Countries +1 (408) 754-1200 6 | Preface Aruba 650 Series Multi-Service Mobility Controller | Installation Guide

Chapter 1 Aruba 650 Series Hardware Overview About the Aruba 650 Series Controller The Aruba 650 Series controller is an enterprise-class, wireless LAN controller. This controller connects, controls, and integrates wireless Access Points (APs) and Air Monitors (AMs) into a wired LAN system. z Aruba 650 Series controller The Aruba 650 is capable of supporting up to 16 external, campus connected APs. „ 650: no built-in external AP support; optional Aruba AP upgrade licenses are available. „ 650-8: includes built-in campus connected AP support for up to 8 APs; optional Aruba AP upgrade licenses are available. The Aruba 651 is capable of supporting up to 16 external, campus connected APs in addition to its single, internal AP. „ 651-1: includes a single, internal AP; no built-in external AP support; optional Aruba AP upgrade licenses are available. „ 651-9: includes a single, internal AP, as well as, built-in campus connected AP support for up to 8 APs; optional Aruba AP upgrade licenses are available. Feature related AP licenses are counted independently and in addition to the Aruba AP upgrade licenses. Contact your Aruba sales representative for complete details regarding software licensing NOTE options and support capacity. Minimum Software Requirements The Aruba 650 Series controller requires ArubaOS 3.4.0 or later. ArubaOS software builds prior to version 3.4.0 does not support the Aruba 650 Series controller. If your network currently runs a software build prior to 3.4.0, you must upgrade the software on your master and local controllers to 3.4.0 or later prior to installing an Aruba 650 Series Mobility Controller in your existing network. The master controller, its redundant master controller, and all of its local controllers must run on the same code of ArubaOS. Once you upgrade your network and install an Aruba 650 Series Mobility Controller into your network, verify that the software version on your controller matches the rest of NOTE your network. If the code shipped on the controller is prior to the version that you upgraded your network to, you must upgrade the code on the controller to match the rest of the network. Package Checklist z Aruba 650 Series Mobility Controller z AC Power Cord (country-specific) z Rack Mount Brackets with Hardware (for rack mounting) z Left Side Bezel (not installed) z Right Side Bezel (not installed) Aruba 650 Series Multi-Service Mobility Controller | Installation Guide Aruba 650 Series Hardware Overview | 7

z Rubber Feet (for table top deployments) z Flat Serial Cable (RJ-45) z Serial Cable Port Adapter (RJ-45 to DB9) z ArubaOS Software Documentation CD z Dual-band, High-gain, Omni-directional Detachable Antennae (3x) z ArubaOS Quick Start Guide z End User License Agreement (EULA) Inform your supplier if there are any incorrect, missing, or damaged parts. If possible, retain the carton, including the original packing materials. Use these materials to repack and return the unit to NOTE the supplier if needed. Hardware Model Overview Front View Figure 1 Aruba 650 Series Front View 10/100/1000Base-T Gigabit Ethernet Ports USB ports LE CONSO Serial Console Port 7 LINK / 6 / ACT 5 LINK ACT LINK ACT / 4 1000 3 2 1 LINK ACT / 0 POE Media Eject Button 1000Base-X (SFP) Ports 10/100/1000Base-T Gigabit Ethernet Ports with PoE 1000Base-X (SFP) Ports There are two 1000Base-X ports for fiber connectivity only and are intended for use with Aruba SFPs (mini-GBICs). To purchase compatible SFP modules, contact your Aruba sales representative for details and assistance. Aruba tests and supports Aruba optics within their controller system. Third party optics are not tested or supported; therefore, Aruba does not guarantee proper functionality of third party optics NOTE when used in an Aruba system. 10/100/1000Base-T Gigabit Ethernet Ports There are six 10/100/1000Base-T Gigabit Ethernet (RJ-45) ports on the Aruba 650 Series. Gigabit Ethernet uses all eight wires and each pair is used in a bi-directional fashion, meaning the same pairs are used for both data transmission and reception. 8 | Aruba 650 Series Hardware Overview Aruba 650 Series Multi-Service Mobility Controller | Installation Guide

Figure 2 illustrates the CAT-5 pin-out found on an RJ-45 connector. The CAT-5 pin-out pairs the following pins on a 10/100/ 1000Base-T Gigabit Ethernet port: 1/2, 3/6, 4/5, and 7/8. Figure 2 Gigabit Ethernet Port Pin-Out 1000Base-T Gigabit RJ-45 Female Signal Name Function Ethernet Port Pin-Out BI_DA+ 1 Bi-directional pair +A 2 BI_DA- Bi-directional pair -A 3 BI_DB+ Bi-directional pair +B 4 BI_DC+ Bi-directional pair +C 5 BI_DC- Bi-directional pair -C 6 BI_DB- Bi-directional pair -B 7 BI_DD+ Bi-directional pair +D 8 BI_DD- Bi-directional pair -D Serial Console Port A serial console port is provided for connection to a terminal, allowing for direct local management. The port’s RJ-45 female connector accepts an RS-232 serial cable with a male connector. Figure 3 Serial Console Port Pin-Out Serial RJ-45 Female Console Port Pin-Out 1 2 3 TxD 4 GND 5 GND 6 RxD 7 8 Direction Input Output Communication settings for the serial port are indicated in Table 1. Table 1 Console Terminal Settings Baud Rate Data Bits Parity Stop Bits Flow Control 9600 8 None 1 None ! CAUTION Do not connect an AP to the serial console port. The serial console port is compatible only with RS- 232 devices. Non-RS-232 devices, such as APs, are not supported. Aruba 650 Series Multi-Service Mobility Controller | Installation Guide Aruba 650 Series Hardware Overview | 9

Serial Console Port Adaptor A modular adaptor can be used to convert the RJ-45 (female) connector to a DB9 (male) connector. Refer to Figure 4 for complete details. Figure 4 RJ-45 (female) to DB9 (male) Modular Adaptor Conversion RJ-45 Female Internal DB-9 Male Pin-Out Connections Pin-Out 1 2 RJ-45 DB-9 3 TxD 3 TxD 2 5 Ground 9 4 4 4 8 5 GND 5 GND 5 3 RxD 7 6 RxD 6 RxD 3 2 TxD 6 7 1 8 Direction Direction Input Input Output Output USB Ports The Aruba 650 Series has four USB 2.0 interfaces. These interfaces allow the use of EVDO/HSPDA modem, flash or disk storage devices, or a printer Media Eject Button The Aruba 650 Series is equipped with a media eject button, which allows users to eject storage devices safely and place the system in standby. Pushing the media eject button changes the state of the Aruba 650 Series; the table below describes the states and LED behaviors associated with use of the media eject button. Table 2 Media Eject Button LED Behavior LED Action Initial State LED State Action Status LED Function Completed NAS Media Operational Green-solid Press and hold Amber-flashing Un-mount all NAS Amber-solid media eject button media for 1 to 5 seconds only NAS Media Unmounted Amber-solid Press and hold Amber-flashing Mount all attached Green-solid media eject button NAS devices, and for 1 to 5 seconds return to fully only functional operation Operational Green-solid Press and hold Red-flashing Controller goes Red-solid media eject button into Standby for more than 5 seconds only Operating with NAS Amber-solid Press and hold Red-flashing Controller goes Red-solid Media un-mounted media eject button into Standby for more than 5 seconds only Standby Red-solid Press media eject Amber-flashing Controller wake-up Green-solid button 10 | Aruba 650 Series Hardware Overview Aruba 650 Series Multi-Service Mobility Controller | Installation Guide

Rear View Figure 5 Aruba 650 Series Rear View (651 Shown) Antennae Interfaces (651 Only) Slot ExpressCard Slot AC Power Socket AC Power Socket The Aruba 650 Series supports integrated AC powering and the AC power socket on the rear of the unit is for use with an AC power cord (country-specific). Refer to "Power Specifications" on page 17 for power specification details. ExpressCard Slot The Aruba 650 Series is equipped with one ExpressCard slot. Antennae Interfaces (Aruba 651 Only) The Aruba 651 is equipped with an internal Access Point (AP). This AP can operate in 2.4 GHz and 5 GHz bands, in a/b/g or n modes. Each appliance has three RP-SMA interfaces to attach the antennae included in this kit. LED Status Indicators Table 3 Aruba 600 Series LED Status Indicators LED Label Function Indicator Status Power POWER Input Power Status Indicator On (Solid Green) Power on Off No Power Status STATUS Module Status Indicator On (Solid Green) Device is operational On (Solid Red) Device failed or is in Standby On (Solid Amber) Device is loading software Off No power Aruba 650 Series Multi-Service Mobility Controller | Installation Guide Aruba 650 Series Hardware Overview | 11

Table 3 Aruba 600 Series LED Status Indicators LED Label Function Indicator Status 1000Base-X Ports (SFP) LNK/ACT Link Status Indicator On (Solid Green) Link has been established On (Flashing Green) Port is transmitting or receiving data Off No link on port 10/100/1000Base-T Ports LNK/ACT Link/Activity Status Indicator On (Solid Green) Link has been established On (Flashing Green) Port is transmitting or receiving data Off No link on port 1000 Interface Speed On (Solid Green) 1000 Mbps Off 10/100 Mbps 10/100/1000Base-T Ports LINK/ACT Link/Activity Status Indicator On (Solid Green) Link has been established with PoE On (Flashing Green) Port is transmitting or receiving data Off No link on port PoE PoE Status Indicator On (Solid Green) PoE is being provided On (Solid Amber) The attached device has requested PoE, but PoE is not being provided by the port Off PoE is not being provided 802.11 a/b/g/n AP WLAN AP Status On (Solid Amber) Radio enabled in WLAN mode (Aruba 651 Only) On (Solid Green) Radio enabled in 802.11n mode On (Flashing Amber) Air monitor mode Off Radio is disabled 12 | Aruba 650 Series Hardware Overview Aruba 650 Series Multi-Service Mobility Controller | Installation Guide

Chapter 2 Aruba 650 Series Installation Installation Pre-Installation Requirements The following tools and equipment are required for installation of an Aruba 650 Series controller. z Rack Mount Bracket (x2, not used for tabletop installation) z 6-32 x 1/4” Phillips Flat Head Screws (4x, included with rack mount brackets) z 12-24 x 5/8” Phillips Flat Head Screws (4x, 19-inch (48.26 cm) rack system mount screws). z Suitable Screwdrivers for both screw types. z AC Power Cord (country-specific) z Left and right side bezels (not used for rack mounting) Physical Installation Rack Mounting To install an Aruba 650 Series controller into a 19-inch (48.26 cm) rack system: 1. Place a rack mount bracket over the mounting holes on one side of the controller (see Figure 6). 2. Secure the bracket to the controller using two 6-32 x 1/4” phillips flat head screws and a suitable screwdriver. 3. Repeat these steps on the opposite side of the controller. Figure 6 Rack Mount Brackets Rack Mount Bracket (2x) OLE CONS 7 LINK / 6 / ACT 5 LINK ACT LINK ACT / 4 1000 3 2 1 LINK ACT / 0 POE 6-32 x 1/4” Phillips Flat Head Screws (4x, 2x per bracket) Aruba 650 Series Multi-Service Mobility Controller | Installation Guide Aruba 650 Series Installation | 13

4. Mount the controller within your organization’s rack system using four 12-24 x 5/8” phillips flat head screws and suitable screwdriver (see Figure 7). Figure 7 Rack Mount Installation Standard 19-inch Rack System SOLE CON 7 LINK / 6 / ACT 5 LINK ACT LINK ACT / 4 1000 3 2 1 LINK ACT / 0 POE 12-24 x 5/8” Phillips Flat Head Screws (4x, 2x per bracket) 5. Leave a minimum of four inches (10cm) of space on the left and right side of the unit for proper air flow and ventilation (see Figure 8). 6. Leave additional space in front and back of the unit to access power cords, network cables, and LED status indicators (see Figure 8). Figure 8 Air Flow Requirements Keep Open for Keep Clear for Easy Access Air Intake LE CONSO 7 LINK / 6 Keep Clear ACT / 5 LINK ACT LINK ACT / 4 1000 3 2 for Air Exhaust LINK ACT / 0 POE 1 Keep Open for Easy Access 14 | Aruba 650 Series Installation Aruba 650 Series Multi-Service Mobility Controller | Installation Guide

7. Connect the AC power cord (country-specific) to the rear of the unit. 8. Plug the opposite end of the power cord into an electrical outlet to power the controller. Aruba 650 Series controller does not have a switch for turning power to the unit on or off. Power to the unit is controlled by connecting or disconnecting the plug on the power cord to or from an NOTE electrical outlet. Tabletop Deployment To deploy an Aruba 650 Series controller on a flat surface, such as a tabletop: 1. Insert the four rubber mounting feet to the bottom of the unit. 2. Attach side bezels by snapping them into place. 3. Place the unit on a hard flat surface. Initial Setup and Network Connectivity Once the physical installation is complete, run the initial setup on the controller to configure the IP address and other basic system information. For complete details and instructions, refer to the ArubaOS Quick Start Guide for the software version installed on your controller. Removal To remove an Aruba 650 Series controller from a 19-inch (48.26 cm) rack system: 1. Disconnect the power to the controller by unplugging the power cord from the electrical outlet. 2. Loosen the four rack mount screws securing the controller to your organizations rack system. 3. Remove the controller from the rack system. Aruba 650 Series Multi-Service Mobility Controller | Installation Guide Aruba 650 Series Installation | 15

16 | Aruba 650 Series Installation Aruba 650 Series Multi-Service Mobility Controller | Installation Guide

Appendix A Specifications, Safety, & Compliance Specifications Physical Specifications Device Dimensions (without rack mount brackets) z Height 1.5˝ (38 mm) z Width 13.6˝ (346 mm) z Depth 8.9˝ (226 mm) Power Specifications z AC Input Voltage: 100-240 V, Universal Input z AC Input Frequency: 50-60 Hz z Maximum power consumption: 126 Watts z Power over Ethernet total capacity: 78 Watts z Power over Ethernet capacity per port: 19.5 Watts Operating Specifications z Operating Temperature Range: 0°C to 40°C (32°F to 104°F) z Operating Humidity Range: 5% to 95% (RH), non-condensing Storage Specifications z Storage Temperature Range: 0°C to 50°C (32°F to 122°F) z Storage Humidity Range: 5% to 95% (RH), non-condensing Wireless Radio Specifications (651 Internal AP) AP type z 2x3, 3x3 Multiple-In, Multiple-Out (MIMO) Operating Frequency z 2.4-2.5 GHz or 5.150–5.950 GHz Available Channels z Mobility Controller-managed, dependent upon configured regulatory domain Modulations z 802.11b: Direct-Sequence Spread-Spectrum (DSSS) z 802.11a/g: Orthogonal Frequency Division Multiplexing (OFDM) z 802.11n: 802.11n draft 2.0 Aruba 650 Series Multi-Service Mobility Controller | Installation Guide Specifications, Safety, & Compliance | 17

Transmit Power z Configurable in increments of 0.5 dBm Association Rates (Mbps) z 802.11b: 11, 5.5, 2, 1 with automatic fallback z 802.11a/g: 54, 48, 36, 24, 18, 12, 9, 6 with automatic fallback z 802.11n: MCS0 - MCS15 (6.5Mbps - 300Mbps) 802.11n High-Throughput (HT) Support z HT 20 z HT 40 802.11n Packet Aggregation z A-MPDU z A-MSDU Antenna (Aruba 651 Internal AP) z Three RP-SMA interfaces for external antenna support (supports up to 3x3 MIMO with spatial diversity) z Three AP-ANT-1B omni-directional dual-band antennas included 18 | Specifications, Safety, & Compliance Aruba 650 Series Multi-Service Mobility Controller | Installation Guide

Safety and Regulatory Compliance Aruba provides a multi-language document containing country specific restrictions and additional safety and regulatory information for all Aruba hardware products. The Aruba Safety and Regulatory Addendum can be viewed or downloaded from the following location: www.arubanetworks.com/safety_addendum. CLASS 1 LASER PRODUCT ! CAUTION Use of controls or adjustments of performance or procedures other than those specified in this manual may result in hazardous radiation exposure. This product complies with 21 CFR Chapter 1, Subchapter J, Part 1040.10, and IEC 60825-1: 1993, A1: 1997, A2: 2001, IEC 60825-2: 2000. For continued compliance with the above laser safety standards, only approved Class 1 modules from our approved vendors should be installed in Aruba products. FCC Class B Device This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits. This equipment should be installed and operated with a minimum distance of 13.78 inches (35 cm) between the radiator and your body for 2.4 GHz and 5 GHz operations. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. When operated in the 5.15 to 5.25 GHz frequency range, this device is restricted to indoor use to reduce the potential for harmful interference with co-channel Mobile Satellite Systems. Aruba 650 z EN 55022 Class B z EN 55024 z IEC/EN 60950 z CE Marking z cTUVus Marked z CB Scheme Certified Aruba 651 z FCC 15.247/15.407 z EU R&TTE Directive 1999/5/EC (EN 300 328, EN 301 893, EN 301 489) z EU LV Directive 2006/95/EC Aruba 650 Series Multi-Service Mobility Controller | Installation Guide Specifications, Safety, & Compliance | 19

z IEC/EN 60950 z CE Marking z cTUVus Marked z CB Scheme Certified For a complete list of Country Specific Regulations please speak with your Aruba Representative. Proper Disposal of Aruba Equipment For the most current information on Global Environmental Compliance and Aruba products please see our website at www.arubanetworks.com. Waste of Electrical and Electronic Equipment Aruba products at end of life are subject to separate collection and treatment in the EU Member States, Norway, and Switzerland and therefore are marked with the symbol shown at the left (crossed-out wheelie bin). The treatment applied at end of life of these products in these countries shall comply with the applicable national laws of countries implementing Directive 2002/96EC on Waste of Electrical and Electronic Equipment (WEEE). European Union RoHS Aruba products also comply with the EU Restriction of Hazardous Substances Directive 2002/95/EC (RoHS). EU RoHS restricts the use of specific hazardous materials in the manufacture of electrical and electronic equipment. Specifically, restricted materials under the RoHS Directive are Lead (including Solder used in printed circuit assemblies), Cadmium, Mercury, Hexavalent Chromium, and Bromine. Some Aruba products are subject to the exemptions listed in RoHS Directive Annex 7 (Lead in solder used in printed circuit assemblies). Products and packaging will be marked with the “RoHS” label shown at the left indicating conformance to this Directive. China RoHS Aruba products also comply with China environmental declaration requirements and are labeled with the “EFUP e” label shown at the left. 20 | Specifications, Safety, & Compliance Aruba 650 Series Multi-Service Mobility Controller | Installation Guide


Document Created: 2009-05-14 13:18:19
Document Modified: 2009-05-14 13:18:19
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC