Test Report

FCC ID: Q23104001

Test Report

Download: PDF
FCCID_428122

EMC Measurement/Technical Report on Flinkstone ROK 104001 Report Reference: 4_Infin_0703_BTT_FCCb Test Laboratory (Headquarter): 7 Layers AG Borsigstr. 11 40880 Ratingen Germany TTI-P-G 178/99 Note: The following test results relate only to the devices specified in this document. This report shall not be reproduced in parts without the written approval of the testing laboratory. Registergericht - registered in: Vorstand - Board of Directors: 7 layers AG, Borsigstrasse 11 Düsseldorf, HRB 44096 Dr. Wolfgang Dahm 40880 Ratingen, Germany Aufsichtratsvorsitzende - Dr. Hans-Jürgen Meckelburg Phone: +49 (0) 2102 749 0 Chairman of the Supervisory Board: Fax: +49 (0) 2102 749 350 Dr. Sabine Grobecker http://www.7Layers.com Interlab is a registered trademark of 7 layers AG

Table of Contents 0. Summary 3 0.1 Technical Report Summary 3 0.2 Measurement Summary 4 1. Administrative Data 5 1.1 Testing Laboratory 5 1.2 Project Data 5 1.3 Applicant Data 5 1.4 Manufacturer Data 5 2. Product Labeling 6 2.1 FCC ID Label 6 2.2 Location of Label on the EUT 6 3. Testobject Data 7 3.1 General EUT Description 7 3.2 EUT Main Components 8 3.3 Ancillary Equipment 8 3.4 EUT Setups 8 3.5 Operating Modes 9 4. Test Results 10 -- Conducted Emissions -- -- Occupied Bandwidth -- -- Peak Power Output -- -- Spurious RF Conducted Emissions -- 4.1 Spurious RF Radiated Emissions 10 -- Dwell Time -- -- Power Density -- -- Channel Separation -- -- Processing Gain 5. Testequipment 14 6. Foto Report 17 7. Setup Drawings 19 8. Annex Testreport Reference: 4_Infin_0703_BTT_FCCb Page 2 of 19

0 Summary 0.1 Technical Report Summary Type of Authorization Certification for an Intentional Radiator (Frequency Hopping Spread Spectrum) Applicable FCC Rules: Prepared in accordance with the requirements of FCC Rules and Regulations as listed in 47 CFR Ch.1 Parts 0 to 19 (10-1-98 Edition). The following subparts are applicable to the results in this test report. Part 2, Subpart J - Equipment Authorization Procedures, Certification Sections Part 15, Subpart C - Intentional Radiators § 15.201 Equipment authorization requirement § 15.207 Conducted limits § 15.209 Radiated emission limits; general requirements § 15.247 Operation within the bands 902-928 MHz, 2400-2483,5 MHZ and 5725-5850 MHz Note: The tests were selected and performed with reference to the FCC Public Notice DA 00- 705, released March 30, 2000 Summary Test Results: The EUT complied with all the applicable FCC rules as listed above. Testreport Reference: 4_Infin_0703_BTT_FCCb Page 3 of 19

#layers 0.2 Measurement Summary FCC Part 15, Subpart C §15.247 (c), §15.35 (b), § 15.209 Spurious Radiated Emissions The measurement was performed according to ANSI C63.4 1992 OP—Mode Setup Port Final Result op—mode 1 21s61g01 enclosure passed op—mode 2 21s61g01 enclosure passed op—mode 3 21s61g01 enclosure passed The basis for this report is the module Flinkstone ROK 104001 (FCC ID: Q23104001). For the use of another antenna the radiated spurious emissions were measured. This report is about this measurement. Responsible for Responsible Accreditation Scope: q_ é’&jé for Test Report: «4 V‘éc layers 7 layers AG, Borsigstr. 11 40880 Ratingen, Germany Phone +49 (0)2102 749 0 Testreport Reference: 4_Infin_0703_BTT_FC Page 4 of 1

1. Administrative Data 1.1 Testing Laboratory Company Name: 7 Layers AG Address: Borsigstr. 11 40880 Ratingen Germany This facility has been fully described in a report submitted to the FCC and accepted under the registration number 96716. The test facility is also accredited by the following accreditation organisation: - Deutscher Akkreditierungs Rat DAR-Registration no. TTI-P-G 178/99 Responsible for Accreditation Scope: Dipl.-Ing Bernhard Retka Dipl.-Ing Arndt Stöcker Dipl.-Ing Thomas Hoell 1.2 Project Data Responsible for testing and report: Robert Machulec Receipt of EUT: 18.12.2003 Date of Test(s): 18.12.2003 Date of Report: 22.12.2003 1.3 Applicant Data Company Name: Infineon Technologies Wireless Solution Sweden AB Address: Isafjordsgatan 16 164 81 Kista-Stockholm Sweden Contact Person: Henrik Arfwedson 1.4 Manufacturer Data Company Name: please see Applicant data Address: Contact Person: Testreport Reference: 4_Infin_0703_BTT_FCCb Page 5 of 19

2.0 Product Labeling 2.1 FCC ID Label: Q23104001 2.2 Location of Label on the EUT: see picture. Testreport Reference: 4_Infin_0703_BTT_FCCb Page 6 of 19

3. Testobject Data 3.1 General EUT Description Equipment under Test: Flinkstone Type Designation: ROK 104001 Kind of Device: Bluetooth module (optional) Voltage Type: DC Voltage level: 3.3 V General product description: Bluetooth is a short-range radio link intended to be a cable replacement between portable and/or fixed electronic devices. Bluetooth operates in the unlicensed ISM Band at 2.4 GHz. In the US a band of 83.5 MHz width is available. In this band, 79 RF channels spaced 1MHz apart are defined. The channel is represented by a pseudo-random hopping sequence through the 79 channels. The channel is devided into time slots, with a nominal slot length of 625µs, where each slot corresponds to different RF hop frequencies. The nominal hop rate is 1600 hops/s. All frequencies are equally used. The average time of occupancy is 0.3797 s within a 30 second period. The symbol rate on the channel is 1 Ms/s. The EUT provides the following ports: Ports temporary antenna connector Enclosure The main components of EUT are listed and described in Chapter 3.2 Testreport Reference: 4_Infin_0703_BTT_FCCb Page 7 of 19

3.2 EUT Main components: Type, S/N, Short Descriptions etc. used in this Test Report Short Equipment Type Serial No. HW Status SW Status Date of Description under Test Designation Receipt EUT A Flinkstone ROK 104001 sample 1 R1 R2 18.12.2003 equipped with a temporary antenna connector. NOTE: The short description is used to simplify the identification of the EUT in this test report 3.3 Ancillary Equipment For the purposes of this test report, ancillary equipment is defined as equipment which is used in conjunction with the EUT to provide operational and control features to the EUT. It is necessary to configure the system in a typical fashion, as a customer would normally use it. But nevertheless Ancillary Equipment can influence the test results. Short Equipment Type HW Status SW Status Serial No. FCC Id Description under Test Designation AE 3 AC power supply Nordic Power AB - - - - AE 2 Antenna LDA922G4520D-185 - - - - AE 1 development board Ericsson-J0025A - - - - 3.4 EUT Setups This chapter describes the combination of EUT's and ancillary equipment used for testing. Setup No. Combination of EUTs Description 21s61g01 EUT A + AE 1 + AE 2 + AE 3 used for radiated measurements. The module under test is seperated from the development bord with a cable of 50cm length. Testreport Reference: 4_Infin_0703_BTT_FCCb Page 8 of 19

3.5 Operating Modes This chapter describes the operating modes of the EUT's used for testing. Op. Mode Description of Operating Modes Remarks op-mode 1 TX mode, the EUT transmits continuously on 2402 MHz op-mode 2 TX mode, the EUT transmits continuously on 2441 MHz op-mode 3 TX mode, the EUT transmits continuously on 2480 MHz Testreport Reference: 4_Infin_0703_BTT_FCCb Page 9 of 19

4. Test Results 4. 1 Spurious Radiated Emissions Standard FCC Part 15, 10-1-98 Subpart C The test was performed according to: ANSI C63.4 1992 4.1.1 Test Description The test set-up was made in accordance to the general provisions of ANSI C63.4-1992. The Equipment Under Test (EUT) was set up on a non-conductive table 1.0 x 2.0 m in the semi-anechoic chamber. The test was performed at an EUT to receiving antenna distance of 3m. The radiated emissions measurements were made in a typical installation configuration. The measurement procedure consists of four steps. It is implemented into EMI test software ES-K1 from R&S. Step 1: Preliminary scan Preliminary test to identify the highest amplitudes relative to the limit. Settings for step 1: - Detector: Peak-Maxhold - Frequency range: 30 – 1000 MHz - Frequency steps: 60 kHz - IF–Bandwidth: 120 kHz - Measuring time / Frequency step: 100 µs - Turntable angle range: –180 to 180 ° - Turntable stepsize: 90° - Height variation range: 1 – 3m - Height variation stepsize: 2m - Polarisation: Horizontal + Vertical Intention of this step is, to determine the radiated EMI-profile of the EUT. With this data, the test system performs ( to reduce the number of final measurements) a data reduction with the following parameters: - Offset for acceptance analysis: Limit line – 10 dB - Maximum number of final measurements: 12 Step 2: With the frequencies determined in step 1, an additional measurement with the following settings will be performed. Intention of this step is, to find out the approximate turntable angle and antenna height for each frequency. Settings for step 2: - Detector: Peak – Maxhold - Measured frequencies: in step 1 determined frequencies - IF – Bandwidth: 120 kHz - Measuring time: 100ms - Turntable angle range: –180 to 180 ° - Turntable stepsize: 45° Testreport Reference: 4_Infin_0703_BTT_FCCb Page 10 of 19

- Height variation range: 1 – 4m - Height variation stepsize: 0,5m - Polarisation: horizontal + vertical After this step the EMI test system has determined the following values for each frequency (of step 1): - Frequency - Azimuth value (of turntable) - Antenna height The last two values have now the following accuracy: - Azimuth value (of turntable): 45° - Antenna height: 0,5m Step 3: In this step the accuracy of the turntable azimuth and antenna height will be improved. This is necessary to find out the maximum value of every frequency. For each frequency the turntable azimuth and antenna height, which was determined in step 3, will be adjusted. The turntable azimuth will be slowly varied by +/- 22,5° around this value. During this action the value of emission is continuously measured. The turntable azimuth at the highest emission will be recorded and adjusted. In this position the antenna height is also slowly varied by +/- 25 cm around the antenna height determined in step 3. During this action the value of emission is also continuously measured. The antenna height of the highest emission will also be recorded and adjusted. Settings for step 3: - Detector: Peak – Maxhold - Measured frequencies: in step 1 determined frequencies - IF – Bandwidth: 120 kHz - Measuring time: 100ms - Turntable angle range: –22,5° to + 22,5 ° around the value determined in step 2 - Height variation range: -0,25m to + 0,25m around the value determined in step 2 Step 4: With the settings determined in step 3, the final measurement will be performed: EMI receiver settings for step 4: - Detector: Quasi-Peak(< 1GHz) - Measured frequencies: in step 1 determined frequencies - IF – Bandwidth: 120 kHz - Measuring time: 1s The following modfications apply to the measurement procedure for the frequency range above 1 GHz: The measurement distance was reduced to 1m. The results were extrapolated by the extrapolation factor of 20 dB/decade (invers linear- distance for field strength measurements, invers linear-distance squared for the power reference level measurements). Due to the fact that in this frequency range a double ridged wave guided horn antenna (up to 18 Ghz) and a horn antenna (18-25 GHz) are used, the steps 2-4 are omitted. Step 1 was performed with one height of the receiving antenna only. Testreport Reference: 4_Infin_0703_BTT_FCCb Page 11 of 19

Detector: Peak, Average RBW = VBW = 1 MHz, above 7 GHz 100 kHz After the measurement a plot will be generated which contains a diagram with the results of the preliminary scan and a chart with the frequencies and values of the results of the final measurement. 4.1.2 Test Limits FCC Part 15, Subpart C, §15.247(c) (2) A radiated emission test applies to harmonic/spurs that fall in the restricted bands as listed in § 15.205(a). The maximum permitted QP (< 1GHz) and average (> 1GHz) field strength is listed in § 15.209(a). (3) FCC Part 15, Subpart C, §15.209, Radiated Emission Limits Frequency Range (MHz): Class B Limit (dBµV/m) 30 – 88 40,0 88 – 216 43,5 216 – 960 46,0 above 960 54,0 §15.35(b) ..., there is also a limit on the radio frequency emissions, as measured using instrumentation with a peak detector function, corresponding to 20 dB above the maximum permitted average limit.... Used conversion factor: Limit (dBµV/m) = 20 log (Limit (µV/m)/1µV/m) 4.1.3 Test Protocol Temperature: 24 °C Air Pressure: 1023 hPa Humidity: 29 % Op. Mode Setup Port Test Parameter op-mode 1 21s61g01 enclosure Polarisation Frequency Corrected Value Limit Limit Delta to Delta to MHz dBµV/m QP/AV Peak AV/QP Peak Limit QP Peak AV dBµV/m dBµV/m Limit/dB dB Vertical 400,00 31,60 46,00 14,40 Vertical 4804,00 57,38 49,25 54,00 74,00 4,75 16,62 Remark: No further spurious emission in the range 20 dB below the limit found. Temperature: 24 °C Air Pressure: 1023 hPa Humidity: 29 % Op. Mode Setup Port Test Parameter op-mode 2 21s61g01 enclosure Polarisation Frequency Corrected Value Limit Limit Delta to Delta to MHz dBµV/m QP/AV Peak AV/QP Peak Limit QP Peak AV dBµV/m dBµV/m Limit/dB dB Vertical 4882,00 56,72 48,88 54,00 74,00 5,12 17,28 Testreport Reference: 4_Infin_0703_BTT_FCCb Page 12 of 19

Remark: No further spurious emission in the range 20 dB below the limit found. Temperature: 24 °C Air Pressure: 1024 hPa Humidity: 29 % Op. Mode Setup Port Test Parameter op-mode 3 21s61g01 enclosure Polarisation Frequency Corrected Value Limit Limit Delta to Delta to MHz dBµV/m QP/AV Peak AV/QP Peak Limit QP Peak AV dBµV/m dBµV/m Limit/dB dB Vertical 400,00 38,30 46,00 7,70 Vertical 4960,00 55,30 47,27 54,00 74,00 6,73 18,70 Remark: No further spurious emission in the range 20 dB below the limit found. 4.1.3 Test result: Spurious Radiated Emissions FCC Part 15, Subpart C Op. Mode Setup Port Result op-mode 1 21s61g enclosure passed 01 op-mode 2 21s61g enclosure passed 01 op-mode 3 21s61g enclosure passed 01 Testreport Reference: 4_Infin_0703_BTT_FCCb Page 13 of 19

5. Testequipment EUT Digital Signalling System Equipment Type Serial No. Manufacturer Digital Radio Communication CMD 55 831050/020 Rohde & Schwarz Tester Signalling Unit for Bluetooth PTW60 100004 Rohde & Schwarz Spurious Emissions Universal Radio Communication CMU 200 102366 Rohde & Schwarz Tester EMI Test System Equipment Type Serial No. Manufacturer Comparison Noise Emitter CNE III 99/016 York EMI Analyzer ESI 26 830482/004 Rohde & Schwarz Signal Generator SMR 20 846834/008 Rohde & Schwarz EMI Radiated Auxiliary Equipment Equipment Type Serial No. Manufacturer Antenna mast 4m MA 240 240/492 HD GmbH H. Deisel Biconical dipole VUBA 9117 9117108 Schwarzbeck Broadband Amplifier 18MHz- JS4-18002600-32-5P 849785 Miteq 26GHz Broadband Amplifier 30MHz- JS4-00101800-35-5P 896037 Miteq 18GHz Broadband Amplifier 45MHz- JS4-00102600-42-5A 619368 Miteq 27GHz Cable "ESI to EMI Antenna" RTK081+Aircell7 W18.01+W38.01a Huber+Suhner Cable "ESI to Horn Antenna" RTK 081 W18.04+3599/001 Rosenberger Double-ridged horn HF 906 357357/002 Rohde & Schwarz Double-ridged horn HF 906 357357/001 Rohde & Schwarz High Pass Filter 4HC1600/12750-1.5- 9942011 Trilithic KK High Pass Filter 5HC2700/12750-1.5- 9942012 Trilithic KK High Pass Filter 5HC3500/12750-1.2- 200035008 Trilithic KK KUEP pre amplifier Kuep 00304000 001 7layers Log.-per. Antenna HL 562 Ultralog 830547/003 Rohde & Schwarz Loop Antenna HFH2-Z2 829324/006 Rohde & Schwarz Pyramidal Horn Antenna 26,5 Model 3160-09 9910-1184 EMCO GHz Testreport Reference: 4_Infin_0703_BTT_FCCb Page 14 of 19

EMI Conducted Auxiliary Equipment Equipment Type Serial No. Manufacturer Cable "LISN to ESI" RG214 W18.03+W48.03 Huber+Suhner Two-Line V-Network ESH 3-Z5 828304/029 Rohde & Schwarz Two-Line V-Network ESH 3-Z5 829996/002 Rohde & Schwarz Auxiliary Test Equipment Equipment Type Serial No. Manufacturer Broadband Resist. Power 1506A / 93459 LM390 Weinschel Divider N Broadband Resist. Power 1515 / 93459 LN673 Weinschel Divider SMA Digital Multimeter 01 Voltcraft M-3860M IJ096055 Conrad Digital Multimeter 02 Voltcraft M-3860M IJ095955 Conrad Digital Oscilloscope TDS 784C B021311 Tektronix Fibre optic link Satellite FO RS232 Link 181-018 Pontis Fibre optic link Transceiver FO RS232 Link 182-018 Pontis I/Q Modulation Generator AMIQ-B1 832085/018 Rohde & Schwarz Notch Filter ultra stable WRCA800/960-6EEK 24 Wainwright Temperature Chamber KWP 120/70 59226012190010 Weiss Temperature Chamber VT 4002 58566002150010 Vötsch ThermoHygro_01 430202 Fischer Anechoic Chamber Equipment Type Serial No. Manufacturer Air Compressor Atlas Copco (pneumatic) Controller HD 100 100/603 HD GmbH H. Deisel EMC Camera CE-CAM/1 CE-SYS EMC Camera for observation of CCD-400E 0005033 Mitsubishi EUT Filter ISDN B84312-C110-E1 Siemens&Matsushita Filter telephone systems / B84312-C40-B1 Siemens&Matsushita modem Filter Universal 1A B84312-C30-H3 Siemens&Matsushita Fully/Semi 10.58x6.38x6 Frankonia AE Chamber Turntable DS 420S 420/573/99 HD GmbH, H. Deisel Valve Control Unit VE 615P 615/348/99 HD GmbH, H. Deisel (pneum.) Testreport Reference: 4_Infin_0703_BTT_FCCb Page 15 of 19

7 layers Bluetooth™ Full RF Test Bluetooth RF Conformance Test Solution System TS8960 Equipment Type Serial No. Manufacturer 10MHz Reference MFS 5489/001 Efratom Power Meter NRVD 832025/059 Rohde & Schwarz 832025/059 Power Sensor A NRV-Z1 832279/013 Rohde & Schwarz 832279/013 Power Sensor B NRV-Z1 832279/015 Rohde & Schwarz 832279/015 Power Supply E3632A MY40003776 Agilent Power Supply PS-2403D - Conrad RF Step Attenuator RSP 833695/001 Rohde & Schwarz 833695/001 Rubidium Frequency Normal MFS 002 Efratom Signal Analyser FSIQ26 FSIQ26 832695/007 Rohde & Schwarz 832695/007 Signal Analyser FSP30 FSP30 100051 Rohde & Schwarz 100051 Signal Generator SMIQ03B 101175 Rohde & Schwarz 101175 Signal Generator SMP 03 833680/003 Rohde & Schwarz 833680/003 Signal Generator A SMIQ03B 834344/002 Rohde & Schwarz 834344/002 Signal Generator B SMIQ03B 832870/017 Rohde & Schwarz 832870/017 Signal Switching and SSCU 338826/005 Rohde & Schwarz Conditioning Unit Signalling Unit PTW60 PTW60 for TS8960 838312/014 Rohde & Schwarz 838312/014 System Controller PSM12 829323/008 Rohde & Schwarz 829323/008 Testreport Reference: 4_Infin_0703_BTT_FCCb Page 16 of 19

6. Foto Report Picture 1 : EUT Picture 2 : External antenna (size of the ground plane of 40 x 25 mm) Testreport Reference: 4_Infin_0703_BTT_FCCb Page 17 of 19

Picture 3 : setup for the test "Spurious emissions radiated" Testreport Reference: 4_Infin_0703_BTT_FCCb Page 18 of 19

7. Setup Drawings Drawing 1 : general test setup Testreport Reference: 4_Infin_0703_BTT_FCCb Page 19 of 19


Document Created: 2004-05-03 16:32:27
Document Modified: 2004-05-03 16:32:27
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC