Test Report HAC RF Appendix C

FCC ID: PY7-PM0860

Test Report

Download: PDF
FCCID_2585039

Calibration Laboratory of Schweizerischer Kalibrierdienst Schmid & Partner Service suisse d‘étalonnage Engineering AG Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreementfor the recognition of calibration certificates Client Sporton—TW (Auden) Certificate No: CD835V3—1045_Sep14 CALIBRATION CERTIFICATE Object CD835V3 — SN: 1045 Calibration procedure(s) QA CAL—20.v6 Calibration procedure for dipoles in air Calibration date: September 23, 2014 This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 x 3)°C and humidity < 70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date (Certificate No.) Scheduled Calibration Power meter EPM~442A GB37480704 09—Oct—13 (No. 217—01827) Oct—14 Power sensor HP 8481A US37202783 09—Oct—13 (No. 217—01827) Oct—14 Power sensor HP 8481A MY41092317 09—Oct—13 (No. 217—01828) Oct—14 Type—N mismatch combination SN: 5047.2 / 06327 03—Apr—14 (No. 217—01921) Apr—15 Probe ER3DV6 SN: 2336 30—Dec—13 (No. ER3—2336_Dec13) Dec—14 Probe H3DV6 SN: 6065 30—Dec—13 (No. H3—6065_Dect3) Dec—14 DAE4 SN: 781 12—Sep—14 (No. DAE4—781_Sep14) Sep—15 Secondary Standards ID # Check Date (in house) Scheduled Check Power meter Agilent 44198 SN: GB40202831 29—Oct—13 (in house check Oct—13) In house check: Oct—15 Power sengor HP E4412A SN: MY41498700 11—Oct—13 (in house check Oct—13) In house check: Oct—15 Power sensor HP E4412A SN: MY41502623 11—Oct—13 (in house check Oct—13) In house check: Oct—15 Network Analyzer HP 8753E US37390585 18—Oct—01 (in house check Oct—13) In house check: Oct—14 AF generator R&S SMT—06 SN: 832283/011 27—Aug—12 (in house check Oct—13) in house check: Oct—16 Name Function Signature Calibrated t by: y Leif Klysner y Laboratory Technician Te —7 f%/ Approved by: Fin Bomholt Deputy Technical Manager _"T::—/ffl / y Te 7 Issued: September 24, 2014 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: CD835V3—1045_Sep14 Page 1 of 8

Calibration Laboratory of & SA S Schweizerischer Kalibrierdienst Schmid & Partner Ste c Service suisse détalonnage Engineering AG P 3 Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland ”’«/,(7 A\> Swiss Calibration Service thits® Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of callbration certificates References {11 ANS1—C63.19—2007 American National Standard for Methods of Measuremnent of Compatibility between Wireless Communications Devices and Hearing Aids. [2] ANSH—C83.19—2011 American National Standard, Methods of Measurement of Compatibility between Wireless Communications Devices and Hearing Aids. Methods Applied and interpretation of Parameters: Coordinate System: y—axis is in the directionof the dipole arms. z—axis is from the basis of the antenna {mounted on the table} towards its feed point betweenthe two dipale arms. x—axis is narmal to the other axes. In coincidence with the standards [1], the measurement planes (probe sensor center) are selected to be at a distance of 10 mm (1§5 mm for [2]) above the top metal edgeof the dipale arms. Measurement Conditions: Further details are available from the hardcopies at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. The forward power to the dipole connector is set with a calibrated power meter connected and monitored with an auxilary power meter connected to a directional coupler. While the dipale under test is connected, the forward poweris adjusted to the same level. Antenna Positioning: The dipole is mounted on a HAC Test Arch phantom using the matching dipole positioner with the arms horizontal and the feeding cable coming fromthe floor. The measurements are performed in a shielded room with absorbers around the setup to reduce the reflections. It is verified before the mounting of the dipole under the Test Arch phantom, that its arms are perfectly in a line. it is installed on the HAC dipole positionerwith its arms paralle! below the dielectric reference wire and able to move elastically in vertical direction without changing its relative position to the top center of the Test Arch phantom. The vertical distance to the probe is adjusted after dipole mounting with a DASYS Surface Check job. Before the measurement, the distance between phantomn surface and probetip is verffied. The proper measurement distance is selected by choosing the matching section of the HAC Test Arch phantorn with the proper device reference point (upper surface of the dipole) and the matching grid reference point (tip of the probe) considering the probe sensor offset. The vertical distance to the probeis essential for the accuracy. Feed Point Impedanceand Return Loss: These parameters are measured using a HP 8753E Vector Network Analyzer. The impedance is specified at the SMA connector of the dipole. The influence of reflections was eliminating by applying the averaging function while moving the dipole in the air, at least 7Ocm away from any obstacles. E—field distribution: E field is measured in the x—y—plane with an isotropic ERSD—field probe with 100 mW forward power to the antenna feed point. In accordance with [1] and [2], the scan area is 20mm wide, its length exceeds the dipole arm length (180 or $Omm). The sensor center is 10 mm(15 mm for [2]) {in z) above the metal top of the dipole arms. Two SD maxima are available near the end of the dipole arms. Assuming the dipole arms are perfectly in one line, the average of these two maxima (in subgrid 2 and subgrid 8) is determined to compensate for any non—parallelity to the measurement plane as well as the sengor displacement. The E—field value stated as calibration value represents the maximumof the interpolated 3D—E— field, in the plane above the dipole surface. H—field distribution: H—field is measured with an isotropic H—field probe with 100mW forward power to the antenna feed point, in the x—y—plane. The scan area and sensor distance is equivalent to the E—field scan. The maximum of the field is available at the center (subgrid 5) above the feed point. The H—field value stated as calibration value represents the maximum of the interpolated H—field, 10mm above the dipole surface at the feed point. The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: CD835Vv3—1045_Sep14 Page 2 of 8

Measurement Conditions DASY system configuration, as far as not given on page 1. DASY Version DASYS V52.8.8 Phantom HAC Test Arch Distance Dipole Top — Probe Center 10 mm Scan resolution dx, dy = 5 mm Frequency 835 MHz a 1 MHz Input power drift <0.05 dB Maximum Field values at 835 MHz H—field 10 mm above dipolte surface condition interpolated maximum Maximum measured 100 mW input power 0.452 A/im + 8.2 % (k=2) E—field 10 mm above dipole surface condition Interpolated maximum Maximum measured above high end 100 mW input power 169.2 V/im = 44.57 dBV/m Maximum measured above low end 100 mW input power 157.6 V/im = 43.95 dBV/m Averaged maximum above arm 100 mW input power 163.4 Vim a 12.8 % ({i=2) E—field 15 mm above dipole surface condition Interpolated maximum Maximum measured above high end 100 mW input power 107.3 V/im = 40.61 dBV/m Maximum measured above low end 100 mW input power 103.9 V/m = 40.33 dBV/m Averaged maximum above arm 100 mW input power 105.6 V/im + 12.8 % (k=2) Certificate No: CDSS5V3—1046_Sep14 Page 3 of 8

Appendix (Additional assessments outside the scope of SCS108) Antenna Parameters Frequency Return Loss Impedance 800 MHz 16.0 dB 42.5 0 — 12.8 jQ. | 835 MHz 32.4 dB 49.2 0 + 2.3 |0 900 MHz 19.1 dB §1.2 9 —11.2 jQ 950 MHz 16.8 do 47.7 2+ 14.1 |Q 980 MHz 12.6 dB 58.9 Q + 24.6 |Q 3.2 Antenna Design and Handling The calibration dipole has a symmetric geometry with a built—in two stub matching network, which leads to the enhanced bandwidth. The dipole is built of standard semirigid coaxial cable. The internal matching line is open ended. The antenna is therefore open for DC signals. Do not apply force to dipole arms, as they are fiable to bend. The soldered connections near the feedpoint may be damaged. After excessive mechanical stress or overheating, check the impedance characteristics to ensure that the internal matching network is not affected. After long term use with 40W radiated power, only a slight warming of the dipole near the feedpoint can be measured. Certificate No: CDS35V3—1045_Sep14 Page 4 of 8

Impedance Measurement Plot 24 Sep 2014 08:22:19 CHL $11 L06 5 dB/REF —18 dB :—37.990 48 835.000 000 MHz CHi Markers 11—15,980 4B 200,000 MHz for B—19.181 dB 900,000 Mz 41—16.793 dB 950.000 Mz fAv 16" 5—12.594 dB | 260.000 MH= | H1d 1 | | | | __| CBZ s1 iu rs £35.000 000 MHz Oel CH2 Markers 1142461 a Cor ~12.754 a 800,000 Niz 3 51198 a ~11.229 a 990,000 MHz bys 4147.689 a 1652 550.000 MHz &4 RH;: S159.947 a 250.000 MHz START $95.000 000 MHz STOP 1 335.000 000 MHz Certificate No: CDB35V3—1045_Sep14 Page 5 of 8

DASY5 H—field Result Date: 23.09.2014 Test Laboratory: SPEAG Lab2 DUT: HAC—Dipole 835 MHz; Type: CD835V3; Serial: CD835V3 — SN: 1045 Communication System: UID 0 — CW ; Frequency: 835 MHz Medium parameters used: 0 =0 S/m, & = [; p= I kg/m3 Phantom section: RF Section Measurement Standard: DASY5 (IEEEAEC/ANSI C63.19—2011) DASY52 Configuration: ® Probe: H3DV6 — SN6065; ; Calibrated: 30.12.2013 * Sensor—Surface: (Fix Surface) * Electronics: DAE4 Sn781; Calibrated: 12.09.2014 ® Phantom: HAC Test Arch with AMCC; Type: SD HAC PO1 BA; Serial: 1070 * DASY52 52.8.8(1222); SEMCAD X 14.6.10(7331} Dipole H—Field measurement @ 835MHz/H—Scan — 835MHz d=10mm/Hearing Aid Compatibility Test (41x361x1): Interpolated grid: dx=0.5000 mm, dy=0.5000 mm Device Reference Point: 0, 0, —6.3 mm Reference Value = 0.4780 A/m; Power Drift=0.01 dB PMR not calibrated. PMF = 1.000 is applied. H—field emissions = 0.4517 A/m Near—field category: M4 (AWF 0 dB) PMF scaled H—field Grid 1 M4 {Grid 2 M4 |Grid 3 M4 0.368 A/m|0.395 A/m|0.380 A/m Grid 4 M4 Grid 6 M4 0.417 A/m 0.436 A/m Grid 7 M4 |Grid 8 M4 |Grid 9 M4 0.368 A/m|0.400 A/m |0.387 A/m ~4.37 ~8.73 "13.10 ~17.46 —21.83 0 dB = 0.4517 A/m =—6.90 dBA/m Certificate No: CD835V3—1045_Sep14 Page 6 of 8

DASY5 E—field Result Date: 23.09.2014 Test Laboralory: SPEAG Lab2 DUT: HAC—Dipole 835 MHz; Type: CD835V3; Serial: CD835V3 — SN: 1045 Communication System: UID 0 — CW ; Frequency: 835 MHz Medium parameters used: o = 0 S/m, &, = 1; p = 1000 kg/m‘ Phantom section: RF Section Measurement Standard: DASYS (IEEEAIEC/ANSI €63.19—2011) DASY52 Configuration: ® Probe: ER3DV6 — SN2336; ConvF(1, 1, 1); Calibrated: 30.12.2013; Sensor—Surface: (Fix Surface) Electronics: DAE4 Sn781; Calibrated: 12.09.2014 Phantom: HAC Test Arch with AMCC; Type: SD HAC PO1 BA; Serial: 1070 e DASY52 52.8.8(1222); SEMCAD X 14.6.10(7331) Dipole E—Field measurement @ 835MHz/E—Scan — 835MHz d=10mm/Hearing Aid Compatibility Test (41x361x1): Interpolated grid: dx=0.5000 mm, dy=0.5000 mm Device Reference Point: 0, 0, —6.3 mm Reference Value = 118.9 V/m; Power Drift= 0.01 dB Applied MIF = 0.00 dB RF audio interference level = 44.57 dBV/m Emission category: M3 MIF scaled E—field Grid 1 M3 [Grid 2 m3 [Grid 3 M3 43.96 dBV/m|44.57 dBV/m [44.39 dBV/m mertimcmm Grid 4 M4 i '1I Grid 6 M4 38.2 dBV/m %g.gnfi_ BV/m|38.74 dBv/m Grid 7 M3 Grid 8 M3 Grid 9 M3 43.39 dBV/m|43.95 dBV/m|43.85 dBV/m Certificate No: CDB35V3—1045_Sep14 Page 7 of 8

Dipole E—Field measurement @ 835MHz/E—Scan — 835MHz d=15mm/Hearing Aid Compatibility Test (41x361x1): Interpolated grid: dx=0.5000 mm, dy=0.5000 mm Device Reference Point: 0, 0, —6.3 mm Reference Value = 118.5 V/m; Power Drift = 0.03 dB Applied MIF = 0.00 dB RF audio interference level = 40.61 dBV/m Emission category: M3 MIF scaled E—field Grid 1 M3 Grid 2 M3 Grid 3 M3 40.31 dBV/m|40.61 dBV/m |40.53 dBV/m Grid 4 M4 Grid 6 M4 35.6 dBV/m 35.94 dBV/m Grid 7 M3 Grid 8 M3 Grid 9 M3 40.01 dBV/m [40.33 dBV/m |40.28 dBV/m —2.46 ~4.92 —T.37 —9.03 —12.29 0 dB = 169.2 V/m = 44.57 dBV/m Certificate No: CDB35V3—1045_Sep14 Page 8 of 8

Calibration Laboratory of Schweizerischer Kalibrierdienst Schmid & Partner Service suisse détalonnage Engineering AG Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Client Sporton—TW {Auden) Certificate No: CD1880V3—1038_Sep14 CALIBRATION CERTIFICATE Object CD1880V3 — SN: 1038 Calibration procedure(s) QA CAL—20.v6 Calibration procedure for dipoles in air Calibration date: September 23, 2014 This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 + 3)°C and hurnidity <70%. Calibration Equipment used (M&TE critical for calibration) PrimaryStandards ID # Cal Date (Certificate No.) Scheduled Calibration Power meter EPM—442A GB37480704 09—Oct—13 (No. 217—01827) Oct—14 Power sensor HP 8481A US37202783 09—Oct—13 (No. 217—01827) Oct—14 Power sensor HP 8481A MY41092317 09—Oct—13 (No. 217—01828) Oct—14 Type—N mismatch combination SN: 5047.2 / 06327 03—Apr—14 (No. 217—01921) Apr~15 Probe ER3DVE SN: 2336 28—Dec—12 (No. ER3—2336_Dec12) Dec—13 Probe H3DV6 SN: 6065 28—Dec—12 (No. H3—6065_Dec12) Dec—13 DaE4 SN: 781 12—Sep—14 (No. DAE4—781_Sep14) Sep—15 Secondary Standards ID # Check Date (inhouse) Scheduled Check Power meter Agilent 44198 SN: GBaczozest 29—Oct—13 (in house check Oct—13} In house check: Oct—15 Power sensor HP E4412A SN: MY41498700 11—Oct—13 (in house check Oct—13) In house check: Oct—15 Power sensor HP E4412A SN: MY41502623 11—Oct—13 (in house check Oct—13) in house check: Oct—16 Network Analyzer HP 8753E US37390586 18—Oct—01 (in house check Oct—13) In house check: Oct—14 RF generator R&S SMT—06 SN: 832283/011 27—Aug—12 (in house check Oct—13) In house check: Oct—16 Name Function Signature Calibrated by: Leif Klysner Laboratory Technician -f %‘——/ %/ s Approved by: Fin Bomholt Deputy Technical Manager l / % ~ ol Ze* Issued: September24, 2014 This calibration certificate shall not be reproduced except in full without written approval of thve laboratory. Certificate No: CD1880v3—1038_Sep14 Page 1 of 10

Calibration Laboratory of Schweizerischer Kalibrierdienst Schmid & Partner Service suisse d‘étalonnage Engineering AG Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreementfor the recognition of calibration certificates References [1] ANSIT—C63.19—2007 American National Standard for Methods of Measurement of Compatibility between Wireless Communications Devices and Hearing Aids. [2] ANSI1—C63.19—2011 American National Standard, Methods of Measurement of Compatibility between Wireless Communications Devices and Hearing Aids. Methods Applied and Interpretation of Parameters: Coordinate System: y—axis is in the direction of the dipole arms. z—axis is from the basis of the antenna {mounted on the table) towards its feed point between the two dipole arms. x—axis is normal to the other axes. In coincidence with the standards [1], the measurement planes (probe sensor center) are selected to be at a distance of 10 mm (15 mm for [2]) above the top metal edge of the dipole arms. Measurement Conditions: Further details are available from the hardcopies at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. The forward power to the dipole connector is set with a calibrated power meter connected and monitored with an auxiliary power meter connected to a directional coupler. While the dipole under test is connected, the forward power is adjusted to the same level. Antenna Positioning: The dipole is mounted on a HAC Test Arch phantom using the matching dipole positioner with the arms horizontal and the feeding cable coming from the floor. The measurements are performed in a shielded room with absorbers around the setup to reduce the reflections. It is verified before the mounting of the dipole under the Test Arch phantom, that its arms are perfectly in a line. It is installed on the HAC dipole positioner with its arms parallel below the dielectric reference wire and able to move elastically in vertical direction without changing its relative position to the top center of the Test Arch phantom. The vertical distance to the probe is adjusted after dipole mounting with a DASY5 Surface Check job. Before the measurement, the distance between phantom surface and probe tip is verified. The proper measurement distance is selected by choosing the matching section of the HAC Test Arch phantom with the proper device reference point (upper surface of the dipole) and the matching grid reference point (tip of the probe) considering the probe sensor offset. The vertical distance to the probe is essential for the accuracy. Feed Point Impedance and Returm Loss: These parameters are measured using a HP 8753E Vector Network Analyzer. The impedance is specified at the SMA connector of the dipole. The influence of reflections was eliminating by applying the averaging function while moving the dipole in the air, at least 70cm away from any obstacles. E—field distribution: E field is measured in the x—y—plane with an isotropic ER3D—field probe with 100 mW forward power to the antenna feed point. In accordance with [1] and [2], the scan area is 20mm wide, its length exceeds the dipole arm fength (180 or 9$Omm). The sensor center is 10 mm (15 mm for [2]) (in z) above the metal top of the dipole arms. Two 3D maxima are available near the end of the dipole arms. Assuming the dipole arms are perfectly in one line, the average of these two maxima (in subgrid 2 and subgrid 8) is determined to compensate for any non—parallelity to the measurement plane as well as the sensor displacement. The E—field value stated as calibration value represents the maximum of the interpolated 3D—E— field, in the plane above the dipole surface. H—field distribution: H—field is measured with an isotropic H—field probe with 100mW forward power to the antenna feed point, in the x—y—plane. The scan area and sensor distance is equivalent to the E—field scan. The maximum of the field is available at the center (subgrid 5) above the feed point. The H—field value stated as calibration value represents the maximum of the interpolated H—field, 10mm above the dipole surface at the feed point. The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: CD1880V3—1038_Sep14 Page 2 of 10

Measurement Conditions DASY system configuration, as far as not given on page 1. DASY Version DASYS V52.8.8 Phantom HAC Test Arch Distance Dipole Top — Probe Center 10 mm Scan resolution dx, dy = 5 mm 1730 MHz #1 MHz Frequency 1880 MHz + 1 MHz Input power drift <0.05 dB Maximum Field values at 1730 MHz HM—field 10 mm above dipole surface condition interpolated maximum Maximum measured 100 mW input power 0.483 Aim * 8.2 % (k=2) E—field 10 mm above dipole surface condition Interpolated maximum Maximum measured above high end 100 mW input power 151.6 V/im =43.61 dBV/m Maximum measured above low end 100 mW input power 148.8 Vim =43.45 dBV/m Averaged maximum above arm 100 mW input power 150.2 V/im £ 12.8 % {k=2) E—fisld 15 mm above dipole surface condition Interpolated maximum Maximum measured above high end 100 mW input power 97.1 V/im = 39.74 dBV/m Maximum measured above low end 100 mW input power 94.6 V/im = 39.52 dBV/m Averaged maximum above arm 100 mW input power 95.8 V/im + 12.8 % (k=2) Maximum Field values at 1880 MHz H—field 10 mm above dipole surface condition interpolated maximum Maximum measured 100 mW inout power 0.464 A/m a 8.2 % (k=2) E—field 10 mm above dipole surface condition Interpolated maximum Maximum measured abovehigh end 100 mW input power 145.3 V/im = 43.25 dBV/m Maximum measured above low end 100 mW input power 136.2 V/im = 42.68 dBV/m Averaged maximum above arm 100 mW input power 140.8 Vim a 12.8 % (k=2) E—field 15 mm above dipole surface condition Interpolated maximum Maximum measured above high end 100 mW input power 90.8 V/m = 39.16 dBV/m Maximum measured abovelow end 100 mW input power 89.4 V/m = 39.03 dBV/m Averaged maximum above arm 100 mW input power 90.1 V/im + 12.8 % (k—=2) Certificate No: CD1880Vv3—1038_Sep14 Page 3 of 10

Appendix (Additional assessments outside the scope of SCS108) Antenna Parameters Nominal Frequencies Frequency Return Loss Impedance 1730 MHz 22.7 4B 514 Q + 7.3 j 1880 MHz 21.8 dB 58.5 Q + 7.6 jQ 1900 MHz 21.6 dB 56.6 Q + 5.9 jQ 1950MHz |0 27.0 dB 54.3 0 — 3.3 |Q 2000 MHz 19.5 dB 40.4 9 — 0.3 jQ Additional Frequencies Frequency Return Loss Impedance 1730 MHz 22.7 dB §1.4 Q + 7.3 jQ 3.2 Antenna Design and Handling The calibration dipole has a symmetric geomeitry with a built—in two stub matching network, which leads to the enhanced bandwidth. The dipole is built of standard semirigid coaxial cable. Theinternal matching lineis open ended. The antenna is therefore open for DC signals. Do not apply force to dipole arms, as they are liable to bend. The soldared connections near the feedpoint may be damaged. After excessive mechanical stress or overheating, check the impedance characteristics to ensure that the internal matching network is not affected. After long term use with 40W radiated power, only a slight warming of the dipole near the feedpoint can be measured. Certificate No: CD1880V3—1038_Sep14 Page 4 of 10

Impedance Measurement Plot 24 Sep 2014 08127121 s11 Los 5 dB/REF —18 ds 2:—21.043 d8 1 $50.000 000 MHz CH1 Markers |L__L_—s 1+~22,730 dB 1.73008 6Hz Cor #—21.535 dB 1.90000 6Hz 41~26.999. 0B 1.95000 6Hz Av 159 5i—15,452 dB 2.00000 OHz Hid CH2 Sit 4 U Fs 2: 53.492 o _7,52;39 645.84 pH 1 $30.000 000 MHz Del CH2 Markers 1151416 a Cor 7.2871 o 1.73008 GHz bi¥d "seerte 1.95000 GHz HLd samgras 2.00000 6Hz CENTER 1 890.000 800 MHz SPAN 1 800,.000 800 MHz Certificate No: CD1880V3—1038_Sep14 Page 5 of 10

DASY5 H—field Resuit Date: 23.09.2014 Test Laboratory: SPEAG, Zurich, Switzerland DUT: HAC Dipole 1880 MHz; Type: CD1880V3; Serial: CD1880V3 — SN: 1038 Communication System: UID 0 — CW ; Frequency: 1880 MHz, Frequency: 1730 MHz Medium parameters used: o = 0 $/m, e = 1; p= 1 kg/m‘ Phantom section: RF Section Measurement Standard: DASY5 (IEEE/EC/ANSI C63.19—2011) DASYS32 Configuration: * Probe: H3DV6 — SN6065; ; Calibrated: 30.12.2013 ® Sensor—Surface: (Fix Surface) ® Electronics: DAE4 Sn781; Calibrated: 12.09.2014 * Phantom: HAC Test Arch with AMCC; Type: SD HAC PO1 BA; Serial: 1070 * DASY52 $2.8.8(1222); SEMCAD X 14.6.10(7331) Dipole H—Field measurement @ 1880MHz/H—Scan — 1880MHz d=10mm/Hearing Aid Compatibility Test (41x181x1): Interpolated grid: dx=0.5000 mm, dy=0.5000 mm Device Reference Point: 0, 0, —6.3 mm Reference Value = 0.4900 A/m:; Power Drift =—0.00 dB PMR not calibrated. PMF = 1.000 is applied. H—field emissions = 0.4637 A/m Near—field category: M2 (AWF 0 dB) PMF scaled H—field Grid 1 M2 Grid 2 M2 Grid 3 M2 0.398 A/m 0.421 A/m 0.405 A/m Grid 4 M2 Grid 6 M2 0.436 A/m |C n|0.446 A/m Grid 7 M2 Grid 8 M2 Grid 9 M2 0.400 A/m 0.430 A/m 0.414 A/m Certificate No: CD1880V3—1038_Sep14 Page 6 of 10

Dipole H—Field measurement @ 1880MHz/H—Scan — 1730MHz d=10mm/Hearing Aid Compatibility Test {41x181x1): Interpolated grid: dx=0.5000 mm, dy=0.5000 mm Device Reference Point: 0, 0, —6.3 mm Reference Value = 0.5130 A/m; Power Drift = 0.03 dB PMR not calibrated. PMF = 1.000 is applied. H—field emissions = 0.4828 A/m Near—field category: M2 {AWF 0 dB) PMEF scaled H—field Grid 1 M2 |Grid 2 M2 |Grid 3 M2 0.390 A/m|0.414 A/m|0.400 A/m Grid 4 M2 Grid 6 M2 0.447 A/m 0.468 A/m Grid 7 M2 |Grid 8 M2 |Grid 9 M2 0.400 A/m |0.434 A/m|0.420 A/m —2.97 5.94 —8.92 11.89 14.86 0 dB = 0.4637 A/m =—6.68 dBA/m Certificate No: CD1880V3—1038_Sep14 Page 7 of 10

DASY5 E—field Result Date: 23.09.2014 Test Laboratory: SPEAG, Zurich, Switzerland DUT: HAC Dipole 1880 MHz; Type: CD1880V3; Serial: CD1880V3 — SN: 1038 Communication System: UID 0 — CW ; Frequency: 1880 MHz, Frequency: 1730 MHz Mediam parameters used: 0 = 0 S/m, &, = 1; p= 1000 kg/m® Phantom section: RF Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C€63.19—2011) DASY52 Configuration: e Probe: ER3DV6 — SN2336; ConvF(1, 1, 1); Calibrated: 30.12.2013; e Sensor—Surface: (Fix Surface) ® Electronics: DAE4 Sn781; Calibrated: 12.09.2014 ® Phantom: HAC Test Arch with AMCC; Type: SD HAC PO1 BA; Serial: 1070 e DASY52 52.8.8(1222); SEMCAD X 14.6.10(7331) Dipole E—Field measurement @ 1880MHz/E—Scan — 1880MHz d=10mm/Hearing Aid Compatibility Test (41x181x1): Interpolated grid: dx=0.5000 mm, dy=0.5000 mm Device Reference Point: 0, 0. —6.3 mm Reference Value = 141.8 V/m; Power Drift = —0.02 dB Applied MIF = 0.00 dB RF audio interference level = 43.25 dBV/m Emission category: M1 MIF scaled E—field Grid 1 M1 Grid 2 M1 Grid 3 M1 42.68 dBV/m (43.25 dBV/m |42.99 dBV/m Grid 4 m2 id 5M2|Grid 6 M2 38.41 dBV/m dBV/m _ |38.94 dBV/m Grid 7 M1 |Grid 8 M1 |Grid 9 M1 42.18 dBV/m|42.68 dBV/m 142.56 dBV/m Certificate No: CD1880V3—1038_Sep14 Page 8 of 10

Dipole E—Field measurement @ 1880MHz/E—Scan — 1880MHz d=15mm/Hearing Aid Compatibility Test (41x181x1): Interpolated grid: dx=0.5000 mm, dy=0.5000 mm Device Reference Point: 0, 0, —6.3 mm Reference Value = 141.9 V/m; Power Drift = —0.00 dB Applied MIF = 0.00 dB RF audio interference level = 39.16 dBV/m Emission category: M2 MIF scaled E—field Grid 1 M2 Grid 2 M2 Grid 3 M2 38.91 dBV/m|39.16 dBV/m|39.03 dBV/m Grid 4 M2 |Gri _|aria 6 mz 36.61 dBV/m |36.8 36.8 dBV/m Grid 7 M2 Grid 8 M2 Grid 9 M2 38.81 dBV/m|39.03 dBV/m|38.96 dBV/m Dipole E—Field measurement @ 1880MH2z/E—Scan — 1730MHz d=10mm/Hearing Aid Compatibility Test (41x181x1): Interpolated grid: dx=0.5000 mm, dy=0.5000 mm Device Reference Point: 0, 0, —6.3 mm Reference Value = 153.0 V/m; Power Drift = —0.01 dB Applied MIF = 0.00 dB RF audio interference level = 43.61 dBV/m Emission category: M1 MIF scaled E—field Grid 1 M1 |Grid 2 M1__ |Grid 3 M1 43 dBV/m |43.61 dBV/m|43.38 dBV/m Grid 4 M2 Er_fijw _faria 6 m 39.67 dBV/m @ ‘m|40.37 dBV/m Grid 7 M1 Grid 8 M1 Grid 9 M1 42.86 dBV/m |43.45 dBV,/m (43.36 dBV/m Certificate No: CD1880v3—1038_Sep14 Page 9 of 10

Dipole E—Field measurement @ 1880MHz/E—Scan — 1730MHz d=15mm/Hearing Aid Compatibility Test (41x181x1): Interpolated grid: dx=0.5000 mm, dy=0.5000 mm Device Reference Point: 0, 0, —6.3 mm Reference Value = 152.8 V/m; Power Drift = —0.01 dB Applied MIF = 0.00 dB RF audio interference level = 39.74 dBV/m Emission category: M2 MIF scaled E—field Grid 1 M2 |Grid2 m2 |Grid 3 M2 39.23 dBV/m [39.52 dBV/m [39.42 dBV/m Grid 4 M2 Grid 6 M2 37.45 dBV/m 37.8 dBV/m Grid 7 M2 Grid 8 M2 Grid 9 M2 39.45 dBV/m [39.74 dBV/m [39.72 dBV/m —1.63 ~4.88 5.50 8.13 0 dB = 145.3 V/m = 43.25 dBV/m Certificate No: CD1880V3—1038_Sep14 Page 10 of 10

Calibration Laboratory of Schweizerischer Kalibrierdienst Schmid & Partner Service suisse d‘étalonnage Engineering AG Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Client Sporton — TW (Auden) Certificate No: DAE3—495_May14 CALIBRATION CERTIFICATE Object DAE3 — SD 000 DO3 AD — SN: 495 Calibration procedure(s) QA CAL—06.v26 Calibration procedure for the data acquisition electronics (DAE) Calibration date: May 19, 2014 This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 + 3)°C and humidity < 70%. Calibration Equipment used (M&TE critica} for calibration) Primary Standards ID # Cal Date (Certificate No.) __ Scheduled Calibration Keithley Multimeter Type 2001 SN: 0810278 01—Oct—13 (No:13976) Oct—14 Secondary Standards ID # Check Date (in house) Scheduled Check Auto DAE Calibration Unit SE UWS 053 AA 1001 07—Jan—14 (in house check) In house check: Jan—15 Calibrator Box V2.1 SE UMS 006 AA 1002 O7—Jan—14 (in house check) In house check: Jan—15 Name Function Signature ___ Calibrated by: Dominique Steffen Technician Fin Bomholt Deputy Technical Manager +N é(k [( Approved by: Issued: May 19, 2014 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: DAE3—495_May14 Page 1 of 5

Calibration Laboratory of Schweizerischer Kalibrierdienst Schmid & Partner Service suisse d‘étalonnage Engineering AG Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland Swiss Calibration Service Accredited by the Swiss Acoreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Glossary DAE data acquisition electronics Connector angle information used in DASY system to align probe sensor X to the robot coordinate system. Methods Applied and Interpretation of Parameters * DC Voltage Measurement: Calibration Factor assessed for use in DASY system by comparison with a calibrated instrument traceable to national standards. The figure given corresponds to the full scale range of the voltmeter in the respective range. * Connector angle: The angle of the connector is assessed measuring the angle mechanically by a tool inserted. Uncertainty is not required. * The following parameters as documented in the Appendix contain technical information as a result from the performance test and require no uncertainty. e DC Voiltage Measurement Linearity: Verification of the Linearity at +10% and —10%of the nominal calibration voltage. Influence of offset voltage is included in this measurement. + Common mode sensitivity: Influence of a positive or negative common mode voltage on the differential measurement. * Channel separation: Influence of a voltage on the neighbor channels not subject to an input voltage. + AD Converter Values with inputs shorted: Values on the internal AD converter corresponding to zero input voltage + Input Offset Measurement. Output voltage and statistical results over a large number of zero voltage measurements. * Input Offset Current: Typical value for information; Maximum channel input offset current, not considering the input resistance. * Input resistance: Typical value for information: DAE input resistance at the connector, during internal auto—zeroing and during measurement. & Low Battery Alarm Voltage: Typical value for information. Below this voltage, a battery alarm signal is generated. «_ Power consumption: Typical value for information. Supply currents in various operating modes. Certificate No: DAE3—495_May14 Page 2 of 5

DC Voltage Measurement A/D — Converter Resolution nominal High Range: 1LSB = 6.AuV , full range = —100...+300 mV Low Range: 1LSB = 61nV , full range = ~1...... +3mV DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec Calibration Factors X Y Z High Range 404.385 + 0.02% (k=2) 405.359 £ 0.02% (k=2) 405.713 + 0.02% (k=2) Low Range 3.95160 £ 1.50% (k=2) $.99165 £ 1.50% (k=2) 3.96622 + 1.50% (k=2) Connector Angle Connector Angle to be used in DASY system 77.0°%1° Certificate No: DAE3—495_May14 Page 3 of 5

Appendix 1. DC Voitage Linearity High Range Reading (uV) Difference (uV) Error (%) Channel X + Input 200034.33 —4.40 —0.00 Channel X + Input 20007.03 2.57 0.01 Channel X — Input ~20001.24 3.51 —0.02 Channel Y + Input 200034.04 —0.65 0.00 Channel Y + Input 20005.84 1.63 0.01 Channel Y — Input —20002.32 2.64 —0.01 Channel Z + Input 200038.21 3.22 0.00 Channel Z + Input 20008.03 3.75 0.02 Channel Z — Input —20002.39 2.50 —0.01 Low Range Reading (uV) Difference (uV) Error (%) Channel X + Input 2000.81 —0.32 —0.02 Channel X + Input 201.28 0.10 0.05 Channel X — Input ~198.05 0.61 —0.31 Channel Y + Input 2000.54 +0.54 —0.03 Channel Y + Input 201.02 —0.05 —0.02 Channel Y — Input —199.81 —1.07 0.54 Channel Z + Input 2000.48 —0.52 —0.03 Channel Z + Input 199.62 —1.35 —0.67 Channel Z — Input —199.45 —0.67 0.34 2. Common mode sensitivity DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec Common mode High Range Low Range Input Voltage (mV) Average Reading (uV) Average Reading (uV) Channel X 200 4.33 2.52 —200 —1.22 —2.61 Channel Y 200 0.12 —0.32 ~200 —0.79 —1.02 Channel Z 200 2.31 2.30 —200 —4.76 —4.84 3. Channel separation DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec Input Voltage (mV) Channel X (uV) Channel Y (uV) Channel Z (uV) Channel X 200 — ~1.27 —2.19 Channel Y 200 8.58 — —0.77 Channel Z 200 5.25 6.26 = Certificate No: DAE3—495_May14 Page 4 of 5

4. AD—Converter Values with inputs shorted DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec High Range (LSB) Low Range (LSB) Channel X 15815 17196 Channel Y 15764 17349 Channel Z 15898 16472 5. Input Offset Measurement DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec Input 10MQ Average (uV) min. Offset (uV) max. Offset (uV) Std. l():\\;;ation Channel X —0.27 —1.43 0.67 0.49 Channel Y —0.09 —1.79 1.08 0.58 Channe! Z —1.01 —2.74 0.55 0.60 6. Input Offset Current Nominal Input circuitry offset current on all channels: <25fA 7. Input Resistance (Typical values for information) Zeroing (kOhm) Measuring (MOhm) Channet X 200 200 Channel Y 200 200 Channel Z 200 200 . Low Battery Alarm Voltage (Typical values for information) Typical values Alarm Level (VDC) Supply (+ Vee) +7.9 Supply (— Vee) —7.6 9. Power Consumption (Typical values for information) Typical values Switched off (mA) Stand by (mA) Transmitting (mA) Supply (+ Vec) +0.01 +6 +14 Supply (— Vec) —0.01 —8 —9 Certificate No: DAE3—495_May14 Page 5 of 5

Calibration Laboratory of Schweizerischer Kalibrierdienst Schmid & Partner Service suisse d‘étalonnage Engineering AG Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Client Auden Certificate No: ER3-2302_JU" 14 CALIBRATION CERTIFICATE Object ER3DV6 — SN:2302 Calibration procedure(s) QA CAL—02.v8, QA CAL—25.v6 Calibration procedure for E—field probes optimized for close near field evaluations in air Calibration date: June 18, 2014 This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of thecertificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 + 3)°C and humidity < 70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID Cal Date (Certificate No.) Scheduled Calibration Power meter E44198 GB41293874 03—Apr—14 (No. 217—01911) Apr—15 Power sensor E4412A MY41498087 03—Apr—14 (No. 217—01911) Apr—15 Reference 3 dB Aftenuator SN: $5054 (3c) 03—Apr—14 (No. 217—01915) Apr—15 Reference 20 dB Attenuator SN: 5277 (20x) 03—Apr—14 (No. 217—01919) Apr—15 Reference 30 dB Aftenuator SN: $5129 (30b) 03—Apr—14 (No. 217—01920) Apr—15 Reference Probe ERSDV6 SN: 2328 10—Oct—13 (No. ER3—2328_Oct13) Oct—14 DaAE4 SN: 789 30—Apr—14 (No. DAE4—789_Apri4) Apr—15 Secondary Standards ID Check Date (in house) Scheduled Check RF generator HP 8648C US3642U01700 4—Aug—99 (in house check Apr—13) In house check: Apr—16 Network Analyzer HP 8753E US37390585 18—Oct—01 (in house check Oct—13) In house check: Oct—14 Name Function Signature Calibrated by: Jeton Kastrati Laboratory Technicia < / Approved by: Kata Pokovic Technical Manager /g/ Issued: June 18, 2014 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: ER3—2302_Jun14 Page 1 of 11

Calibration Laboratory of wHlym Schweizerischer Kalibrierdienst Schmid & Partner y 4 ixnz—_ jsofrr Service suisse d‘étalonnage Engineering AG 27— _‘ Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland 77,4/,_\\\9} Swiss Calibration Service rlitae® Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Glossary: NORMx.y,z sensitivity in free space DCP diode compression point CF crest factor (1/duty_cycle) of the RF signal A, B,C, D modulation dependent linearization parameters Polarization p ip rotation around probe axis Polarization 8 8 rotation around an axis that is in the plane normal to probe axis (at measurement center), i.e., 9 = 0 is normal to probe axis Connector Angle information used in DASY system to align probe sensor X to the robot coordinate system Calibration is Performed According to the Following Standards: a) IEEE Std 1309—2005, " IEEE Standard for calibration of electromagneticfield sensors and probes, excluding antennas, from 9 kHz to 40 GHz", December 2005 b) CTIA Test Plan for Hearing Aid Compatibility, April 2010. Methods Applied and Interpretation of Parameters: NORMx,y,z: Assessed for E—field polarization 3 = 0 for XY sensors and 3 = 90 for Z sensor (f < 900 MHz in TEM—cell; f > 1800 MHz: R22 waveguide). NORM(Mx.y,z = NORMx,y,z * frequency_response (see Frequency Response Chart). DCPx,y,z: DCP are numerical linearization parameters assessed based on the data of power sweep with CW signal (no uncertainty required). DCP does not depend on frequency nor media. PAR: PAR is the Peak to Average Ratio that is not calibrated but determined based on the signal characteristics Axy,z; Bxy,z; Cx,y,2; Dx,y,2; VRx,y,z: A, B, C, D are numerical linearization parameters assessed based on the data of power sweep for specific modulation signal. The parameters do not depend on frequency nor media. VR is the maximum calibration range expressed in RMS voltage across the diode. Spherical isotropy (3D deviation from isotropy): in a locally homogeneous field realized using an open waveguide setup. Sensor Offset: The sensor offset corresponds to the offset ofvirtual measurement center from the probe tip (on probe axis). No tolerance required. Connector Angle: The angle is assessed using the information gained by determining the NORMx (no uncertainty required). Certificate No: ER3—2302_Jun14 Page 2 of 11

ERSDV6 — SN:2302 June 18, 2014 Probe ER3DVG6 SN:2302 Manufactured: November 6, 2002 Calibrated: June 18, 2014 Calibrated for DASY/EASY Systems (Note: non—compatible with DASY2 system!) Certificate No: ER3—2302_Jun14 Page 3 of 11

ER3DVE— SN:2302 June 18, 2014 DASY/EASY — Parameters of Probe: ER3DVG6 — SN:2302 Basic Calibration Parameters Sensor X Sensor Y Sensor Z Unc (k=2) Norm (uV/(V/m)") 146 1.33 142 £10.1 % DCP (mV)" 103.0 100.6 108.0 Modulation Calibration Parameters UID Communication System Name A B C D VR Unc® dB dByuV dB mV (k=2) 0 Cw x 0.0 0.0 1.0 0.00 155.6 44.1 % Y 0.0 0.0 1.0 139.3 Z 0.0 0.0 1.0 134.1 10011— UMTS—FDD (WCDMA) x 3.20 67.2 19.2 291 1248 10.7% CAB Y 3.02 65.4 17.8 110.4 Z 3.91 72.1 21.6 144.9 10012— IEEE 802.11b WiFi 2.4 GHz (DSSS, 1 X 2.68 68.3 19.3 1.87 126.7 20.9 % CAA Mbps) ¥. 2.70 67.5 18.3 1114 2 3.86 76.3 23.0 145.8 10021— GSM—FDD (TDMA, GMSK) x 8.99 88.6 24.0 9.39 1128 #17% DAB Y 12.90 95.7 26.8 139.7 Z 8.28 85.2 22.2 131.5 10039— CDMA2000 (1xRTT, RC1) x 4.63 66.7 19.4 4.57 124.1 £1.2 % CAB Y 4.81 67.3 19.4 146.6 Z 4.67 67.7 19.8 134.5 10081— CDMA2000 (1xRTT, RC3) X 3.77 65.9 18.9 3.97 120.9 20.7 % CAB Y 3.97 66.7 19.0 142.9 Z 3.97 67.7 19.7 132.3 10100— LTE—FDD (SC—FDMA, 100% RB, 20 x 6.54 68.6 20.7 5.67 138.1 £1.7 % CAB MHz, QPSK) Y 6.28 67.1 19.7 116.6 Z 6.06 66.9 19.6 107.4 10108— LTE—FDD (SCG—FDMA, 100% RB, 10 x 6.41 68.1 20.6 5.80 135.7 #1.7% CAB MHz, QPSK) ¥ 6.16 66.7 19.6 115.3 Z 5.92 66.4 19.5 106.2 10154— LTE—FDD (SC—FDMA, 50% RB, 10 MHz, x 6.10 67.6 204 5.75 1323 +17% CAB QPSK) ¥ 5.85 66.2 19.4 113.2 Z 6.03 67.7 20.2 145.8 10169— LTE—FDD (SC—FDMA, 1 RB, 20 MHz, x 4.88 666 20.1 5.73 1160 #1.7% CAB QPSK) Y 5.08 67.3 20.3 138.2 Z 4.93 67.5 20.4 127.9 10175— LTE—FDD (SC—FDMA, 1 RB, 10 MHz, x 4.86 66.5 19.9 5.72 119.2 £1.4 % CAB QPSK) Y 5.06 67.3 20.2 137.8 Z 4.98 67.7 20.5 132.8 Certificate No: ER3—2302_Jun14 Page 4 of 11

ERGDV6— SN:2302 June 18, 2014 10295— CDMA2000, RC1, S03, 1/athRate 25. x 964 B6.3 356 1249 1005 #41% AAB v |_8.36 80.4 32.3 83.8 z 810 79.2 30.7 824 10297— LTE—FDD (SC—FDMA, 50% RB, 20 MHz, x 6.37 67.8 204 581 1391 +1.7% AAA aPSK) v 623 67.0 19.8 119.1 z 594 66.5 19.5 1112 The reported uncertainty of measurementis stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. 5 Numerical linearization parameter: uncertainty not required. * Uncertainty is determined using the max. deviation from linear response applying rectangular distribution and is expressed for the square of the field value Certificate No: ER3—2302_Jun14 Page 5 of 11

ER3DV6— SN:2302 June 18, 2014 Frequency Response of E—Field (TEM—Cell:ifi110 EXX, Waveguide: R22) Frequency response (normalized) 0.5 JB3 13 [OOfOfGera® ; it u. j agh 3i. cup ce usys di Sb ul i l L1 0 1000 1500 2000 2500 f [MHz] & TE'I\?I'TIO" ) & R22_(0]") _o} TEM (90°) [+] R22 (90°) Uncertainty of Frequency Response of E—field: £ 6.3% (k=2) Certificate No: ER3—2302_Jun14 Page 6 of 11

ER3DVE— SN:2302 June 18, 2014 Receiving Pattern (¢), 8 = 0° £=600 MHz,TEM,O° £=2500 MHz,R22,0° so so 135 a ao ' * mm A yiart i’ d2 o« os os * * * § I;:_o.: os os V s 315 370 # e e & ® e # e e Tot X Y 2 Tot X Y 2 Receiving Pattern (¢), 8 = 90° f=600 MHz,TEM,90° f=2500 MHz,R22,90° gere.e 135 ." * as i \ “, 4 0 o2 o« o6 08 0 *3 s 3;5 *sts~ # ® e & # Tot X Y £ Tot Certificate No: ER3—2302_Jun14 Page 7 of 11

ER3DV6— SN:2302 June 18, 2014 Receiving Pattern (¢), 8 = 0° 0.5 4 Error[dB] 0.0—7 mES Uncertainty of Axial Isotropy Assessment: * 0.5% (k=2) Receiving Pattern (¢), 8 = 90° otmi it a ob o4bie ob ob t P944e . Error [dB] 0.07 _l 1 i 1 L— 44 f 1 1 1 1 1 1 1 i 1 1 150 ~100 50 0 50 100 CCz Roll [*] e (® *J ® mEmJHz BCWLZ 1800 MHz 2 Uncertainty of Axial Isotropy Assessment: £ 0.5% (k=2) Certificate No: ER3—2302_Jun14 Page 8 of 11

ER3DV6— SN:2302 June 18, 2014 Dynamic Range f(E—field) (TEM cell , f= 900 MHz) z 10 S © & .9 ® § 10%7 a 2 107 19)— 10 10‘ 10° 10+ E total [V/m] K3 Le] not compensated compensated 2— 14 8 —f S § 4 "\E 24 —2 100 103 E total [V/m] _* L®] not compensated compensated Uncertainty of Linearity Assessment: £ 0.6% (k=2) Certificate No: ER3—2302_Jun14 Page 9 of 11

ER3DV6— SN:2302 June 18, 2014 Deviation from Isotropy in Air Error (6, 3), f= 900 MHz g & €> & —1.0 —0.8 —0.6 —0.4 —0.2 0.0 02 0.4 0.6 08 1.0 Uncertainty of Spherical Isotropy Assessment: £ 2.6% (k=2) Certificate No: ER3—2302_Jun14 Page 10 of 11

ER3DV6— SN:2302 June 18, 2014 DASY/EASY — Parameters of Probe: ER3DVG6 — SN:2302 Other Probe Parameters Sensor Arrangement Rectangular Connector Angle (°) —2.9 Mechanical Surface Detection Mode enabled Optical Surface Detection Mode disabled Probe Overall Length 337 mm Probe Body Diameter 10 mm Tip Length 10 mm Tip Diameter 8 mm Probe Tip to Sensor X Calibration Point 2.5 mm Probe Tip to Sensor Y Calibration Point 2.5 mm Probe Tip to Sensor Z Calibration Point 2.5 mm Certificate No: ER3—2302_Jun14 Page 11 of 11


Document Created: 2015-03-04 14:37:33
Document Modified: 2015-03-04 14:37:33
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC