16J23633D-S1V2 FCC SAR Report C2PC

FCC ID: PY7-96946K

RF Exposure Info

Download: PDF

FCCID_3107832

Report No.: 16J23633D-S1V2 Issue Date: 8/22/2016

Revision History
Rev. Date Revisions Revised By
V1 8/17/2016 Initial Issue --
V2 8/22/2016 Section 10.2: Updated Table Coltyce Sanders

Page 2 of 31
UL Verification Services Inc. Doc. No.: 1.0
This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 16J23633D-S1V2 Issue Date: 8/22/2016

Table of Contents

1. Attestation of Test Results ......................................................................................................... 5

2. Test Specification, Methods and Procedures............................................................................ 6

3. Facilities and Accreditation ........................................................................................................ 6

4. SAR Measurement System & Test Equipment .......................................................................... 7
4.1. SAR Measurement System ........................................................................................................ 7
4.2. SAR Scan Procedures ............................................................................................................... 8
4.3. Test Equipment........................................................................................................................ 10

5. Measurement Uncertainty ......................................................................................................... 10

6. Device Under Test (DUT) Information ...................................................................................... 11
6.1. DUT Description ...................................................................................................................... 11
6.2. Wireless Technologies ............................................................................................................. 12
6.3. Maximum Output Power from Tune-up Procedure ................................................................... 13
6.4. General LTE SAR Test and Reporting Considerations............................................................. 13
6.5. LTE (TDD) Considerations ....................................................................................................... 15

7. RF Exposure Conditions (Test Configurations) ...................................................................... 16

8. Dielectric Property Measurements & System Check .............................................................. 17
8.1. Dielectric Property Measurements ........................................................................................... 17
8.2. System Check.......................................................................................................................... 19

9. Conducted Output Power Measurements................................................................................ 20
9.1. LTE .......................................................................................................................................... 20
9.2. LTE Carrier Aggregation .......................................................................................................... 25

10. Measured and Reported (Scaled) SAR Results ....................................................................... 26
10.1. LTE Band 7 (20MHz Bandwidth) .......................................................................................... 27
10.2. LTE Band 41 (20MHz Bandwidth) ........................................................................................ 27

11. SAR Measurement Variability ................................................................................................... 28

12. Simultaneous Transmission SAR Analysis ............................................................................. 29
12.1. Sum of the SAR for LTE Band 7 & Wi-Fi & BT .................................................................... 30
12.2. Sum of the SAR for LTE Band 41 & Wi-Fi & BT .................................................................. 30

Appendixes .......................................................................................................................................... 31
16J23633D-S1V1 SAR_App A Setup Photos & Ant. Locations .......................................................... 31
16J23633D-S1V1 SAR_App B System Check Plots ........................................................................... 31
16J23633D-S1V1 SAR_App C Highest Test Plots ............................................................................. 31
Page 3 of 31
UL Verification Services Inc. Doc. No.: 1.0
This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 16J23633D-S1V2 Issue Date: 8/22/2016

2. Test Specification, Methods and Procedures
The tests documented in this report were performed in accordance with FCC 47 CFR § 2.1093, IEEE STD 1528-
2013, the following FCC Published RF exposure KDB procedures:
o 447498 D01 General RF Exposure Guidance v06
o 447498 D03 Supplement C Cross-Reference v01
o 648474 D04 Handset SAR v01r03
o 865664 D01 SAR measurement 100 MHz to 6 GHz v01r04
o 865664 D02 RF Exposure Reporting v01r02
o 941225 D05 SAR for LTE Devices v02r05
o 941225 D05A LTE Rel.10 KDB Inquiry Sheet v01r02
o 941225 D06 Hotspot Mode v02r01
In addition to the above, the following information was used:
o TCB workshop October, 2014; Page 36, RF Exposure Procedures Update (Overlapping LTE Bands)
o TCB workshop October, 2014; Page 37, LTE Considerations (LTE Band 41 Test Channels)

3. Facilities and Accreditation
The test sites and measurement facilities used to collect data are located at

47173 Benicia Street 47266 Benicia Street
SAR Lab A SAR Lab 1
SAR Lab B SAR Lab 2
SAR Lab C SAR Lab 3
SAR Lab D SAR Lab 4
SAR Lab E SAR Lab 5
SAR Lab F
SAR Lab G
SAR Lab H

UL Verification Services Inc. is accredited by NVLAP, Laboratory Code 200065-0.

Page 6 of 31
UL Verification Services Inc. Doc. No.: 1.0
This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 16J23633D-S1V2 Issue Date: 8/22/2016

6.2. Wireless Technologies
Wireless Duty Cycle used for
Frequency bands Operating mode
technologies SAR testing
GPRS Multi-Slot Class: GSM Voice: 12.5%
Voice (GMSK) ☐ Class 8 - 1 Up, 4 Down (E)GPRS: 1 Slot: 12.5%
850
GPRS (GMSK) ☐ Class 10 - 2 Up, 4 Down 2 Slots: 25%
GSM 1900
EGPRS (8PSK) ☐ Class 12 - 4 Up, 4 Down 3 Slots: 37.5%
☒ Class 33 - 4 Up, 5 Down 4 Slots: 50%
Does this device support DTM (Dual Transfer Mode)? ☒ Yes ☐ No
UMTS Rel. 99 (Voice & Data)
Band II HSDPA (Rel. 5)
W-CDMA (UMTS) Band IV HSUPA (Rel. 6) 100%
Band V HSPA+ (Rel. 7)
DC-HSDPA (Rel. 8)
FDD Band 2
FDD Band 4
FDD Band 5
FDD Band 7 QPSK
FDD Band 12 16QAM 100% (FDD)
LTE FDD Band 13 ☒ Rel. 11 Carrier Aggregation (1 Uplink and 3 Downlinks) 63.3% (TDD)
(Carrier Aggregation is only supported for downlink and not
FDD Band 17 for uplink.)
FDD Band 26
FDD Band 29 (Rx Only)
TDD Band 41
Does this device support SV-LTE (1xRTT-LTE)? ☐ Yes ☒ No
802.11b
2.4 GHz 802.11g 100%
802.11n (HT20)
802.11a
802.11n (HT20)
Wi-Fi 802.11n (HT40)
5 GHz 100%
802.11ac (VHT20)
802.11ac (VHT40)
802.11ac (VHT80)
Does this device support bands 5.60 ~ 5.65 GHz? ☒ Yes ☐ No
Does this device support Band gap channel(s)? ☒ Yes ☐ No
Bluetooth 2.4 GHz Version 4.2 LE 77.5% (DH5)

Page 12 of 31
UL Verification Services Inc. Doc. No.: 1.0
This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 16J23633D-S1V2 Issue Date: 8/22/2016
Release 11 Carrier Aggregation (CA) Combinations:
Bandw idth (MHz)
Combination CA configuration Carrier 1 Carrier 2

20 15 10 5 3 1.4 20 15 10 5 3 1.4
2A-4A √ √ √ √ √ √ √ √ √ √
2A-5A √ √ √ √ √ √
2A-12A √ √ √ √ √ √
2A-13A √ √ √ √ √
2A-17A √ √ √ √
2A-29A √ √ √ √ √
Inter-Band 4A-5A √ √ √ √
4A-7A √ √ √ √ √ √
4A-12A √ √ √ √ √ √
4A-13A √ √ √ √ √
4A-17A √ √ √ √
4A-29A √ √ √ √ √
5A-7A √ √ √ √ √ √ √
√ √
7C
√ √
Intra-Band
√ √
contiguous
41C √ √ √
√ √ √ √
2A-2A √ √ √ √ √ √ √ √
Intra-Band
4A-4A √ √ √ √ √ √ √ √
non-contiguous
7A-7A √ √ √ √

Notes:
For supported channels, please refer to the channels above.

Release 11 Carrier Aggregation (CA) Combinations (continued):
Bandw idth (MHz)
Combination CA configuration Carrier 1 Carrier 2 Carrier 3
20 15 10 5 3 1.4 20 15 10 5 3 1.4 20 15 10 5 3 1.4
2A-2A-13A √ √ √ √ √ √ √ √ √
4A-4A-5A √ √ √ √ √ √ √ √ √ √
4A-4A-12A √ √ √ √ √ √ √ √ √ √
4A-4A-13A √ √ √ √ √ √ √ √ √
Inter-Band
2A-4A-5A √ √ √ √ √ √ √ √ √ √
2A-4A-12A √ √ √ √ √ √ √ √ √ √
2A-4A-13A √ √ √ √ √ √ √ √ √
2A-4A-29A √ √ √ √ √ √ √ √ √ √

Notes:
For supported channels, please refer to the channels above.

Page 14 of 31
UL Verification Services Inc. Doc. No.: 1.0
This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 16J23633D-S1V2 Issue Date: 8/22/2016

6.5. LTE (TDD) Considerations
According to KDB 941225 D05 SAR for LTE Devices, for Time-Division Duplex (TDD) systems, SAR must be
tested using a fixed periodic duty factor according to the highest transmission duty factor implemented for the
device and supported by the defined 3GPP LTE TDD configurations.

SAR was tested with the highest transmission duty factor (63.33%) using Uplink-downlink configuration 0 and
Special subframe configuration 7.

LTE TDD Bands support 3GPP TS 36.211 section 4.2 for Type 2 Frame Structure and Table 4.2-2 for uplink-
downlink configurations and Table 4.2-1 for Special subframe configurations.

Table 4.2-1: Configuration of special subframe (lengths of DwPTS/GP/UpPTS).
Normal cyclic prefix in downlink Extended cyclic prefix in downlink
Special DwPTS UpPTS DwPTS UpPTS
subframe Extended
Normal cyclic Extended cyclic Normal cyclic
configuration cyclic prefix in
prefix in uplink prefix in uplink prefix in uplink
uplink
0 6592 ⋅ Ts 7680 ⋅ Ts
1 19760 ⋅ Ts 20480 ⋅ Ts
2192 ⋅ Ts 2560 ⋅ Ts
2 21952 ⋅ T s 2192 ⋅ Ts 2560 ⋅ Ts 23040 ⋅ Ts
3 24144 ⋅ Ts 25600 ⋅ Ts
4 26336 ⋅ Ts 7680 ⋅ Ts
5 6592 ⋅ T s 20480 ⋅ Ts
4384 ⋅ Ts 5120 ⋅ Ts
6 19760 ⋅ Ts 23040 ⋅ Ts
7 21952 ⋅ Ts 4384 ⋅ Ts 5120 ⋅ Ts 12800 ⋅ Ts
8 24144 ⋅ Ts - - -
9 13168 ⋅ T s - - -

Calculated Duty Cycle
Downlink-to- Subframe Number
Uplink-
Uplink Calculated
Downlink
Switch-point 0 1 2 3 4 5 6 7 8 9 Duty Cycle (%)
Configuration
Periodicity
0 5 ms D S U U U D S U U U 63.33
1 5 ms D S U U D D S U U D 43.33
2 5 ms D S U D D D S U D D 23.33
3 10 ms D S U U U D D D D D 31.67
4 10 ms D S U U D D D D D D 21.67
5 10 ms D S U D D D D D D D 11.67
6 5 ms D S U U U D S U U D 53.33

Calculated Duty Cycle = Extended cyclic prefix in uplink x (Ts) x # of S + # of U

Example for Calculated Duty Cycle for Uplink-Downlink Configuration 0:
Calculated Duty Cycle = 5120 x [1/(15000 x 2048)] x 2 + 6 ms = 63.33%
where
Ts = 1/(15000 x 2048) seconds

Page 15 of 31
UL Verification Services Inc. Doc. No.: 1.0
This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 16J23633D-S1V2 Issue Date: 8/22/2016

7. RF Exposure Conditions (Test Configurations)
Refer to “SAR Photos and Ant locations” Appendix for the specific details of the antenna-to-antenna and
antenna-to-edge(s) distances.
Wireless RF Exposure DUT-to-User Test Antenna-to- SAR
Note
technologies Conditions Separation Position edge/surface Required
Left Touch N/A Yes
Left Tilt (15°) N/A Yes
Head 0 mm
Right Touch N/A Yes
Right Tilt (15°) N/A Yes
Rear N/A Yes
Body 15 mm
Front N/A Yes
WWAN Rear < 25 mm Yes
Front < 25 mm Yes
Edge 1 (Top) > 25 mm No 1
Hotspot 10 mm
Edge 2 (Right) < 25 mm Yes
Edge 3 (Bottom) < 25 mm Yes
Edge 4 (Left) < 25 mm Yes
Notes:
1. SAR is not required because the distance from the antenna to the edge is > 25 mm as per KDB 941225 D06 Hot Spot SAR.

Page 16 of 31
UL Verification Services Inc. Doc. No.: 1.0
This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 16J23633D-S1V2 Issue Date: 8/22/2016

8. Dielectric Property Measurements & System Check
8.1. Dielectric Property Measurements
The temperature of the tissue-equivalent medium used during measurement must also be within 18°C to 25°C and
within ± 2°C of the temperature when the tissue parameters are characterized.
The dielectric parameters must be measured before the tissue-equivalent medium is used in a series of SAR
measurements. The parameters should be re-measured after each 3 – 4 days of use; or earlier if the dielectric
parameters can become out of tolerance; for example, when the parameters are marginal at the beginning of the
measurement series.
Tissue dielectric parameters were measured at the low, middle and high frequency of each operating frequency
range of the test device.
For SAR measurement systems that have implemented the SAR error compensation algorithms documented in
IEEE Std 1528-2013, to automatically compensate the measured SAR results for deviations between the measured
and required tissue dielectric parameters, the tolerance for εr and σ may be relaxed to ± 10%. This is limited to
frequencies ≤ 3 GHz.

Tissue Dielectric Parameters
FCC KDB 865664 D01 SAR Measurement 100 MHz to 6 GHz
Hεad Body
Targεt Frεquεncy (MHz)
εr σ (S/m) εr σ (S/m)
150 52.3 0.76 61.9 0.80
300 45.3 0.87 58.2 0.92
450 43.5 0.87 56.7 0.94
835 41.5 0.90 55.2 0.97
900 41.5 0.97 55.0 1.05
915 41.5 0.98 55.0 1.06
1450 40.5 1.20 54.0 1.30
1610 40.3 1.29 53.8 1.40
1800 – 2000 40.0 1.40 53.3 1.52
2450 39.2 1.80 52.7 1.95
3000 38.5 2.40 52.0 2.73
5000 36.2 4.45 49.3 5.07
5100 36.1 4.55 49.1 5.18
5200 36.0 4.66 49.0 5.30
5300 35.9 4.76 48.9 5.42
5400 35.8 4.86 48.7 5.53
5500 35.6 4.96 48.6 5.65
5600 35.5 5.07 48.5 5.77
5700 35.4 5.17 48.3 5.88
5800 35.3 5.27 48.2 6.00

IEEE Std 1528-2013
Refer to Table 3 within the IEEE Std 1528-2013

Page 17 of 31
UL Verification Services Inc. Doc. No.: 1.0
This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 16J23633D-S1V2 Issue Date: 8/22/2016
Dielectric Property Measurements Results:
Relative Permittivity (єr) Conductivity (σ)
SAR Tissue Band Frequency
Date Delta Delta
Room Type (MHz) (MHz) Measured Target Measured Target
±5 % ±5 %
2600 39.31 39.01 0.77 1.97 1.96 0.25
1 7/29/2016 2600 Head 2495 39.64 39.14 1.27 1.85 1.85 0.02
2690 38.99 38.90 0.24 2.07 2.06 0.41
2600 50.79 52.51 -3.28 2.16 2.16 -0.22
1 7/29/2016 2600 Body 2495 51.15 52.64 -2.84 2.01 2.01 -0.31
2690 50.44 52.40 -3.74 2.28 2.29 -0.14
2600 37.94 39.01 -2.74 2.05 1.96 4.58
2 8/3/2016 2600 Head 2495 38.38 39.14 -1.95 1.93 1.85 4.51
2690 37.54 38.90 -3.49 2.16 2.06 4.64
2600 54.02 52.51 2.87 2.22 2.16 2.79
2 8/3/2016 2600 Body 2495 54.34 52.64 3.22 2.11 2.01 4.86
2690 53.76 52.40 2.60 2.33 2.29 1.78

Page 18 of 31
UL Verification Services Inc. Doc. No.: 1.0
This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 16J23633D-S1V2 Issue Date: 8/22/2016
LTE Band 7 Measured Results
BW RB RB Max. Avg Pwr (dBm)
Band Mode MPR
(MHz) Allocation offset 2510 MHz 2535 MHz 2560 MHz
1 0 0 19.9 19.8 19.8
1 49 0 19.3 19.4 19.0
1 99 0 19.6 19.5 19.3
QPSK 50 0 1 18.5 18.6 18.4
50 24 1 18.4 18.5 18.2
50 50 1 18.4 18.5 18.1
LTE 100 0 1 18.5 18.6 18.3
20
Band 7 1 0 1 19.0 19.0 19.0
1 49 1 18.8 18.8 18.6
1 99 1 19.0 18.9 18.8
16QAM 50 0 2 17.5 17.5 17.4
50 24 2 17.4 17.5 17.2
50 50 2 17.4 17.4 17.1
100 0 2 17.5 17.6 17.3
BW RB RB Max. Avg Pwr (dBm)
Band Mode MPR
(MHz) Allocation offset 2507.5 MHz 2535 MHz 2562.5 MHz
1 0 0 19.6 19.6 19.4
1 37 0 19.3 19.5 19.2
1 74 0 19.4 19.4 19.1
QPSK 36 0 1 18.5 18.7 18.4
36 20 1 18.4 18.6 18.3
36 39 1 18.5 18.6 18.2
LTE 75 0 1 18.5 18.6 18.4
15
Band 7 1 0 1 18.9 18.6 18.8
1 37 1 18.8 18.5 18.5
1 74 1 18.9 18.4 18.5
16QAM 36 0 2 17.4 17.7 17.4
36 20 2 17.4 17.6 17.3
36 39 2 17.5 17.6 17.2
75 0 2 17.6 17.6 17.3
BW RB RB Max. Avg Pwr (dBm)
Band Mode MPR
(MHz) Allocation offset 2505 MHz 2535 MHz 2565 MHz
1 0 0 19.6 19.7 19.2
1 25 0 19.5 19.6 19.0
1 49 0 19.6 19.6 19.0
QPSK 25 0 1 18.6 18.6 18.2
25 12 1 18.7 18.7 18.2
25 25 1 18.6 18.5 18.1
LTE 50 0 1 18.6 18.7 18.1
10
Band 7 1 0 1 18.5 18.7 18.6
1 25 1 18.5 18.7 18.5
1 49 1 18.5 18.5 18.5
16QAM 25 0 2 17.7 17.6 17.2
25 12 2 17.8 17.7 17.1
25 25 2 17.7 17.5 17.1
50 0 2 17.6 17.7 17.1

Page 21 of 31
UL Verification Services Inc. Doc. No.: 1.0
This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 16J23633D-S1V2 Issue Date: 8/22/2016
LTE Band 7 Measured Results (continued)
BW RB RB Max. Avg Pwr (dBm)
Band Mode MPR
(MHz) Allocation offset 2502.5 MHz 2535 MHz 2567.5 MHz
1 0 0 19.4 19.7 19.1
1 12 0 19.5 19.9 19.1
1 24 0 19.6 19.7 19.1
QPSK 12 0 1 18.6 18.6 18.0
12 7 1 18.5 18.7 18.1
12 13 1 18.5 18.6 18.1
LTE 25 0 1 18.5 18.7 18.1
5
Band 7 1 0 1 18.7 18.2 18.3
1 12 1 18.8 18.3 18.2
1 24 1 18.9 18.3 18.3
16QAM 12 0 2 17.6 17.8 17.2
12 7 2 17.6 17.9 17.2
12 13 2 17.6 17.8 17.2
25 0 2 17.5 17.8 17.1

Page 22 of 31
UL Verification Services Inc. Doc. No.: 1.0
This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 16J23633D-S1V2 Issue Date: 8/22/2016
LTE Band 41 Measured Results
BW RB RB Max. Avg Pwr (dBm)
Band Mode MPR
(MHz) Allocation offset 2506 MHz 2549.5 MHz 2593 MHz 2636.5 MHz 2680 MHz
1 0 0 22.1 22.5 21.7 22.5 21.8
1 50 0 21.9 22.0 21.6 22.2 21.5
1 99 0 22.3 22.1 22.0 22.4 21.8
QPSK 50 0 1 21.0 21.3 20.7 21.4 20.7
50 25 1 21.0 21.1 20.7 21.3 20.7
50 50 1 21.1 21.1 20.8 21.4 20.7
LTE
100 0 1 21.1 21.2 20.7 21.3 20.8
Band 20
41 1 0 1 21.2 21.4 20.7 21.5 20.8
1 50 1 21.1 20.9 20.5 21.1 20.4
1 99 1 21.4 21.1 20.9 21.3 20.7
16QAM 50 0 2 20.0 20.3 19.7 20.4 19.7
50 25 2 20.0 20.1 19.7 20.2 19.7
50 50 2 20.2 20.0 19.7 20.3 19.6
100 0 2 20.0 20.1 19.7 20.3 19.7
BW RB RB Max. Avg Pwr (dBm)
Band Mode MPR
(MHz) Allocation offset 2506 MHz 2549.5 MHz 2593 MHz 2636.5 MHz 2680 MHz
1 0 0 21.8 22.1 21.5 22.1 21.6
1 36 0 21.7 21.6 21.4 21.9 21.3
1 74 0 21.8 21.6 21.4 21.9 21.3
QPSK 36 0 1 20.9 21.1 20.6 21.2 20.6
36 18 1 20.9 20.9 20.5 21.0 20.5
36 37 1 20.9 20.8 20.6 21.0 20.5
LTE
75 0 1 20.9 20.9 20.5 21.1 20.6
Band 15
41 1 0 1 20.8 21.2 20.6 21.3 20.6
1 36 1 20.7 20.9 20.5 21.0 20.3
1 74 1 20.9 20.7 20.5 21.0 20.3
16QAM 36 0 2 19.8 20.0 19.5 20.2 19.5
36 18 2 19.8 19.9 19.5 20.0 19.4
36 37 2 19.9 19.8 19.5 20.0 19.4
75 0 2 19.8 19.9 19.5 20.0 19.5
BW RB RB Max. Avg Pwr (dBm)
Band Mode MPR
(MHz) Allocation offset 2506 MHz 2549.5 MHz 2593 MHz 2636.5 MHz 2680 MHz
1 0 0 22.0 22.0 21.4 21.9 21.7
1 25 0 22.0 21.8 21.4 21.8 21.6
1 49 0 22.1 21.8 21.4 21.8 21.6
QPSK 25 0 1 21.1 21.0 20.5 21.0 20.7
25 12 1 21.1 20.9 20.4 20.9 20.6
25 25 1 21.1 20.9 20.5 20.8 20.7
LTE
50 0 1 21.1 20.9 20.5 20.8 20.8
Band 10
41 1 0 1 21.0 21.0 20.4 20.7 20.7
1 25 1 20.9 20.9 20.3 20.6 20.6
1 49 1 21.0 20.8 20.4 20.6 20.7
16QAM 25 0 2 20.0 19.9 19.5 19.9 19.6
25 12 2 20.1 19.8 19.4 19.8 19.6
25 25 2 20.2 19.8 19.5 19.8 19.6
50 0 2 20.1 19.9 19.5 19.8 19.7

Page 23 of 31
UL Verification Services Inc. Doc. No.: 1.0
This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 16J23633D-S1V2 Issue Date: 8/22/2016
LTE Band 41 Measured Results (continued)
BW RB RB Max. Avg Pwr (dBm)
Band Mode MPR
(MHz) Allocation offset 2506 MHz 2549.5 MHz 2593 MHz 2636.5 MHz 2680 MHz
1 0 0 22.2 21.9 21.6 22.0 21.6
1 12 0 22.2 21.8 21.6 22.0 21.6
1 24 0 22.1 21.7 21.5 21.9 21.5
QPSK 12 0 1 21.1 20.9 20.5 20.8 20.7
12 7 1 21.1 20.8 20.4 20.8 20.6
12 13 1 21.1 20.9 20.4 20.8 20.6
LTE
25 0 1 21.1 20.8 20.4 20.8 20.6
Band 5
41 1 0 1 21.2 20.3 20.4 21.0 20.6
1 12 1 21.3 20.4 20.4 20.9 20.5
1 24 1 21.4 20.4 20.4 21.0 20.5
16QAM 12 0 2 20.1 19.9 19.5 19.7 19.7
12 7 2 20.1 19.8 19.4 19.8 19.6
12 13 2 20.0 19.9 19.4 19.8 19.6
25 0 2 20.1 19.9 19.4 19.8 19.6

Page 24 of 31
UL Verification Services Inc. Doc. No.: 1.0
This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 16J23633D-S1V2 Issue Date: 8/22/2016

9.2. LTE Carrier Aggregation
PCC PCC (UL) SCC SCC (DL) LTE Rel 8 LTE Rel 11
PCC (UL) PCC UL# SCC (DL)
PCC Band Bandwidth Frequency SCC Band Bandwidth Frequency Tx. Power Tx. Power
Channel RB/Offset Channel
[MHz] [MHz] [MHz] [MHz] [dBm] [dBm]

Band 4 10 20000 1715 RB 1/0 Band 7 20 3100 2655 20.85 20.80

Band 5 10 20450 829 RB 1/0 Band 7 20 3100 2655 23.76 23.80

Band 7 20 20850 2510 RB 1/0 Band 7 20 3100 2655 19.01 19.00

Band 7 20 21350 2560 RB 1/0 Band 7 20 3100 2655 18.92 18.90

Band 41 20 41055 2636.5 RB 1/0 Band 41 20 40620 2593 22.54 22.53

Note:
Per KDB 941225 D05A LTE Rel. 10 KDB Inquiry Sheet: SAR is excluded for Carrier Aggregation when measured
1
power does not exceed LTE Release 8 by more than a /4 dBm

Page 25 of 31
UL Verification Services Inc. Doc. No.: 1.0
This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 16J23633D-S1V2 Issue Date: 8/22/2016

10. Measured and Reported (Scaled) SAR Results
SAR Test Reduction criteria are as follows:

KDB 447498 D01 General RF Exposure Guidance:
Testing of other required channels within the operating mode of a frequency band is not required when the reported 1-g or 10-g
SAR for the mid-band or highest output power channel is:
• ≤ 0.8 W/kg or 2.0 W/kg, for 1-g or 10-g respectively, when the transmission band is ≤ 100 MHz
• ≤ 0.6 W/kg or 1.5 W/kg, for 1-g or 10-g respectively, when the transmission band is between 100 MHz and 200 MHz
• ≤ 0.4 W/kg or 1.0 W/kg, for 1-g or 10-g respectively, when the transmission band is ≥ 200 MHz

KDB 648474 D04 Handset SAR:
With headset attached, when the reported SAR for body-worn accessory, measured without a headset connected to the
handset, is > 1.2 W/kg, the highest reported SAR configuration for that wireless mode and frequency band should be repeated
for that body-worn accessory with a headset attached to the handset.

KDB 648474 D04 Handset SAR (Phablet Only):
When Hotspot Mode is not supported, 10-g Extremity SAR is required for all surfaces and edges with an antenna located at ≤ 25
mm from that surface or edge in direct contact with a flat phantom, to address interactive hand use exposure conditions.

Additional 1-g SAR testing at 5 mm is not required when hotspot mode 10-g extremity SAR is not required for the surfaces and
edges since all 1-g reported SAR < 1.2 W/kg.

KDB 941225 D05 SAR for LTE Devices:
SAR test reduction is applied using the following criteria:
• Start with the largest channel bandwidth and measure SAR for QPSK with 1 RB, and 50% RB allocation, using the RB
offset and required test channel combination with the highest maximum output power among RB offsets at the upper edge,
middle and lower edge of each required test channel.
• When the reported SAR is > 0.8 W/kg, testing for other Channels is performed at the highest output power level for 1RB,
and 50% RB configuration for that channel.
• Testing for 100% RB configuration is performed at the highest output power level for 100% RB configuration across the
Low, Mid and High Channel when the highest reported SAR for 1 RB and 50% RB are > 0.8 W/kg. Testing for the
remaining required channels is not needed because the reported SAR for 100% RB Allocation < 1.45 W/kg.
• Testing for 16-QAM modulation is not required because the reported SAR for QPSK is < 1.45 W/Kg and its output power is
not more than 0.5 dB higher than that of QPSK.
• Testing for the other channel bandwidths is not required because the reported SAR for the highest channel bandwidth is <
1.45 W/Kg and its output power is not more than 0.5 dB higher than that of the highest channel bandwidth.
• For LTE bands that do not support at least three non-overlapping channels in certain channel bandwidths, test the available
non-overlapping channels instead. When a device supports overlapping channel assignment in a channel bandwidth
configuration, the middle channel of the group of overlapping channels should be selected for testing; therefore, the
requirement for H, M and L channels may not fully apply.

Page 26 of 31
UL Verification Services Inc. Doc. No.: 1.0
This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 16J23633D-S1V2 Issue Date: 8/22/2016

10.1. LTE Band 7 (20MHz Bandwidth)
Power (dBm) 1-g SAR (W/kg)
RF Exposure Dist. Test Freq. RB RB Plot
Mode Ch #. Tune-up
Conditions (mm) Position (MHz) Allocation offset Meas. Meas. Scaled No.
limit
1 0 20.0 18.9 0.154 0.198
Left Touch 21100 2535.0
50 0 19.0 17.7 0.134 0.182
1 0 20.0 18.9 0.092 0.118
Left Tilt 21100 2535.0
50 0 19.0 17.7 0.069 0.094
Head QPSK 0
1 0 20.0 18.9 0.404 0.520 1
Right Touch 21100 2535.0
50 0 19.0 17.7 0.327 0.444
1 0 20.0 18.9 0.083 0.107
Right Tilt 21100 2535.0
50 0 19.0 17.7 0.069 0.094
1 0 20.0 18.9 0.134 0.173
Rear 21100 2535.0
50 0 19.0 17.7 0.107 0.145
Body-worn QPSK 15
1 0 20.0 18.9 0.135 0.174 2
Front 21100 2535.0
50 0 19.0 17.7 0.106 0.144
1 0 20.0 18.9 0.261 0.336
Rear 21100 2535.0
50 0 19.0 17.7 0.204 0.277
1 0 20.0 18.9 0.312 0.402 3
Front 21100 2535.0
50 0 19.0 17.7 0.246 0.334
1 0 20.0 18.9 0.143 0.184
Hotspot QPSK 10 Edge 2 21100 2535.0
50 0 19.0 17.7 0.114 0.155
1 0 20.0 18.9 0.093 0.120
Edge 3 21100 2535.0
50 0 19.0 17.7 0.073 0.099
1 0 20.0 18.9 0.030 0.039
Edge 4 21100 2535.0
50 0 19.0 17.7 0.024 0.033

10.2. LTE Band 41 (20MHz Bandwidth)
Power (dBm) 1-g SAR (W/kg)
RF Exposure Dist. Test Freq. RB RB Plot
Mode Ch #. Tune-up
Conditions (mm) Position (MHz) Allocation offset Meas. Meas. Scaled No.
limit
1 99 23.0 22.0 0.173 0.216
Left Touch 40620 2593.0
50 50 22.0 20.8 0.137 0.182
1 99 23.0 22.0 0.095 0.119
Left Tilt 40620 2593.0
50 50 22.0 20.8 0.072 0.096
Head QPSK 0
1 99 23.0 22.0 0.412 0.515 4
Right Touch 40620 2593.0
50 50 22.0 20.8 0.318 0.423
1 99 23.0 22.0 0.062 0.077
Right Tilt 40620 2593.0
50 50 22.0 20.8 0.048 0.064
1 99 23.0 22.0 0.212 0.265
Rear 40620 2593.0
50 50 22.0 20.8 0.175 0.233
Body-worn QPSK 15
1 99 23.0 22.0 0.240 0.300 5
Front 40620 2593.0
50 50 22.0 20.8 0.198 0.263
1 99 23.0 22.0 0.391 0.489
Rear 40620 2593.0
50 50 22.0 20.8 0.322 0.428
1 99 23.0 22.0 0.529 0.661 6
Front 40620 2593.0
36 50 22.0 20.8 0.425 0.565
1 99 23.0 22.0 0.309 0.386
Hotspot QPSK 10 Edge 2 40620 2593.0
50 50 22.0 20.8 0.249 0.331
1 99 23.0 22.0 0.151 0.189
Edge 3 40620 2593.0
50 50 22.0 20.8 0.120 0.160
1 99 23.0 22.0 0.038 0.047
Edge 4 40620 2593.0
50 50 22.0 20.8 0.030 0.040

Page 27 of 31
UL Verification Services Inc. Doc. No.: 1.0
This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 16J23633D-S1V2 Issue Date: 8/22/2016

11. SAR Measurement Variability
In accordance with published RF Exposure KDB 865664 D01 SAR measurement 100 MHz to 6 GHz. These
additional measurements are repeated after the completion of all measurements requiring the same head or body
tissue-equivalent medium in a frequency band. The test device should be returned to ambient conditions (normal
room temperature) with the battery fully charged before it is re-mounted on the device holder for the repeated
measurement(s) to minimize any unexpected variations in the repeated results.

1) Repeated measurement is not required when the original highest measured SAR is <0.8 or 2 W/kg (1-g or 10-g
respectively); steps 2) through 4) do not apply.
2) When the original highest measured SAR is ≥ 0.8 or 2 W/kg (1-g or 10-g respectively), repeat that
measurement once.
3) Perform a second repeated measurement only if the ratio of largest to smallest SAR for the original and first
repeated measurements is > 1.20 or 3 (1-g or 10-g respectively) or when the original or repeated measurement
is ≥ 1.45 or 3.6 W/kg (~ 10% from the 1-g or 10-g respective SAR limit).
4) Perform a third repeated measurement only if the original, first, or second repeated measurement is ≥ 1.5 or
3.75 W/kg (1-g or 10-g respectively) and the ratio of largest to smallest SAR for the original, first and second
repeated measurements is > 1.20 or 3 (1-g or 10-g respectively).

Frequency Repeated Highest
Band Air Interface RF Exposure Conditions Test Position SAR Measured
(MHz) (Yes/No) SAR (W/kg)

LTE Band 7 Head Right Touch No 0.404
2600
LTE Band 41 Hotspot Front No 0.529
Note(s):
Repeated measurement is not required when the original highest measured SAR is <0.8 (1-g).

Page 28 of 31
UL Verification Services Inc. Doc. No.: 1.0
This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 16J23633D-S1V2 Issue Date: 8/22/2016

12.1. Sum of the SAR for LTE Band 7 & Wi-Fi & BT
Standalone SAR (WCkg) ∑ 1-g SAR (WCkg)
RF
Test DTS U-NII
Exposure WWAN BT WWAN + DTS WWAN + U-NII WWAN+DTS+U-NII WWAN+DTS+U-NII WWAN+U-NII+BT WWAN+DTS+U-NII+BT
Position
conditions Chain 0 Chain 1 Chain 0 Chain 1
① ⑥ ① +② +③ ① +④ +⑤ ① +② +⑤ ① +③ + ④ ① +④ +⑤ +⑥ ① +③ +④ +⑥
② ③ ④ ⑤
Left Touch 0.198 0.629 0.377 0.810 0.322 1.204 1.330 1.149 1.385
Left Tilt 0.118 0.629 0.377 0.810 0.322 1.124 1.250 1.069 1.305
Head
Right Touch 0.520 0.196 0.377 0.166 0.322 1.093 1.008 1.038 1.063
Right Tilt 0.107 0.196 0.377 0.166 0.322 0.680 0.595 0.625 0.650
Rear 0.173 0.055 0.126 0.039 0.107 0.210 0.354 0.319 0.335 0.338 0.529 0.548
Body-w orn
Front 0.174 0.055 0.126 0.039 0.107 0.210 0.355 0.320 0.336 0.339 0.530 0.549
Rear 0.336 0.125 0.189 0.650 0.336 0.461 0.525
Front 0.402 0.125 0.189 0.716 0.402 0.527 0.591
Edge 1 0.125 0.189 0.314 0.125 0.189
Hotspot
Edge 2 0.184 0.125 0.189 0.498 0.184 0.309 0.373
Edge 3 0.120 0.120 0.120 0.120 0.120
Edge 4 0.039 0.039 0.039 0.039 0.039

12.2. Sum of the SAR for LTE Band 41 & Wi-Fi & BT
Standalone SAR (WCkg) ∑ 1-g SAR (WCkg)
RF
Test DTS U-NII
Exposure WWAN BT WWAN + DTS WWAN + U-NII WWAN+DTS+U-NII WWAN+DTS+U-NII WWAN+U-NII+BT WWAN+DTS+U-NII+BT
Position
conditions Chain 0 Chain 1 Chain 0 Chain 1
① ⑥ ① +② +③ ① +④ +⑤ ① +② +⑤ ① +③ + ④ ① +④ +⑤ +⑥ ① +③ +④ +⑥
② ③ ④ ⑤
Left Touch 0.216 0.629 0.377 0.810 0.322 1.222 1.348 1.167 1.403
Left Tilt 0.119 0.629 0.377 0.810 0.322 1.125 1.251 1.070 1.306
Head
Right Touch 0.515 0.196 0.377 0.166 0.322 1.088 1.003 1.033 1.058
Right Tilt 0.077 0.196 0.377 0.166 0.322 0.650 0.565 0.595 0.620
Rear 0.265 0.055 0.126 0.039 0.107 0.210 0.446 0.411 0.427 0.430 0.621 0.640
Body-w orn
Front 0.300 0.055 0.126 0.039 0.107 0.210 0.481 0.446 0.462 0.465 0.656 0.675
Rear 0.489 0.125 0.189 0.803 0.489 0.614 0.678
Front 0.661 0.125 0.189 0.975 0.661 0.786 0.850
Edge 1 0.125 0.189 0.314 0.125 0.189
Hotspot
Edge 2 0.386 0.125 0.189 0.700 0.386 0.511 0.575
Edge 3 0.189 0.189 0.189 0.189 0.189
Edge 4 0.047 0.047 0.047 0.047 0.047

Conclusion:
Simultaneous transmission SAR measurement (Volume Scan) is not required because either the sum of the 1-g SAR is < 1.6 W/kg or the SPLSR is ≤ 0.04 for all circumstances that
require SPLSR calculation.

Page 30 of 31
UL Verification Services Inc. Doc. No.: 1.0
This report shall not be reproduced without the written approval of UL Verification Services Inc.

Document Created: 2016-08-22 08:25:30
Document Modified: 2016-08-22 08:25:30

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC