PY7-76486P_SZEM1807006310PS RPT

FCC ID: PY7-76486P

Test Report

Download: PDF
FCCID_4077166

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch No. 1 Workshop, M-10, Middle section, Science & Technology Park, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Report No.: SZEM180700631002 Fax: +86 (0) 755 2671 0594 Page: 1 of 19 Email: ee.shenzhen@sgs.com TEST REPORT Application No.: SZEM1807006310PS Applicant: Sony Mobile Communications Inc. Address of Applicant: 4-12-3 Higashi-Shinagawa, Shinagawa-ku, Tokyo, Japan Manufacturer: Sony Mobile Communications Inc. Address of Manufacturer: 4-12-3 Higashi-Shinagawa, Shinagawa-ku, Tokyo, Japan Equipment Under Test (EUT): EUT Name: Charger FCC ID: PY7-76486P Trade mark: SONY Standard(s) : 47 CFR Part 15, Subpart B Date of Receipt: 2018-07-17 Date of Test: 2018-07-17 to 2018-07-19 Date of Issue: 2018-11-16 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. Keny Xu EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180700631002 Page: 2 of 19 Revision Record Version Chapter Date Modifier Remark 01 2018-11-16 Original Authorized for issue by: Foray Chen /Project Engineer Eric Fu /Reviewer This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180700631002 Page: 3 of 19 2 Test Summary Emission Part Item Standard Method Requirement Result Conducted Emissions 47 CFR Part 15, at Mains Terminals ANSI C63.4:2014 Class B Pass Subpart B (150kHz-30MHz) Radiated Emissions 47 CFR Part 15, ANSI C63.4:2014 Class B Pass (30MHz-1GHz) Subpart B Internal Source Upper Frequency Below 1.705MHz 30MHz 1.705MHz to 108MHz 1GHz 108MHz to 500MHz 2GHz 500MHz to 1GHz 5GHz Above 1GHz 5th harmonic of the highest frequency or 40GHz, whichever is lower This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS—CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZENM180r006s1002 Page Aof 19 3 Contents Page 1. covenprce 2. Test summany. s contents a eenenaL inFonmation s 41— bemuscrEUT s 42. Descartonor Supzort Uins s 43 Mexsureent Uicermiay s aa TesLoownon s 45— TestFroum s 48. Devamonrromstawowes s 47 AmvommumesrronStaicaro Conmions s s Eoupment List. 3 s emssion tesr resuuts. a a.1 Coroucren EmssonsarMans Teruus B0z000z s €.1.1 EUT. Operaton a €.1.2 TestSotup Diagram a 618| Measuremont Data a s2 MaowieoBussous GoVHz1GH2) is €21 EUT.Operation is €22.. TestSetupDiagram is €28.| Measurmmont Data is 7 pHotocnaphs a

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180700631002 Page: 5 of 19 4 General Information 4.1 Details of E.U.T. Power supply: Input: AC100-240V 50-60Hz 500mA Output: DC5.0V 3000mA / DC9.0V 2000mA / DC12.0V 1500mA Test voltage: AC120V 60Hz 4.2 Description of Support Units Description Manufacturer Model No. Serial No. Load Resistor SGS N/A REF. No.SEA0600 Type-C Cable SONY N/A 100cm shielded 4.3 Measurement Uncertainty No. Item Measurement Uncertainty 1 Conduction Emission ± 3.0dB (150kHz to 30MHz) 2 Radiated Emission ± 4.5dB (30MHz-1GHz) 3 Temperature test ± 1°C 4 Humidity test ± 3% This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180700631002 Page: 6 of 19 4.4 Test Location All tests were performed at: SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen Branch No. 1 Workshop, M-10, Middle Section, Science & Technology Park, Shenzhen, Guangdong, China. 518057. Tel: +86 755 2601 2053 Fax: +86 755 2671 0594 No tests were sub-contracted. 4.5 Test Facility The test facility is recognized, certified, or accredited by the following organizations: • CNAS (No. CNAS L2929) CNAS has accredited SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch EMC Lab to ISO/IEC 17025:2005 General Requirements for the Competence of Testing and Calibration Laboratories (CNAS-CL01 Accreditation Criteria for the Competence of Testing and Calibration Laboratories) for the competence in the field of testing. • A2LA (Certificate No. 3816.01) SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory is accredited by the American Association for Laboratory Accreditation(A2LA). Certificate No. 3816.01. • VCCI The 3m Fully-anechoic chamber for above 1GHz, 10m Semi-anechoic chamber for below 1GHz, Shielded Room for Mains Port Conducted Interference Measurement and Telecommunication Port Conducted Interference Measurement of SGS-CSTC Standards Technical Services Co., Ltd. have been registered in accordance with the Regulations for Voluntary Control Measures with Registration No.: G-20026, R-14188, C-12383 and T-11153 respectively. • FCC –Designation Number: CN1178 SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory has been recognized as an accredited testing laboratory. Designation Number: CN1178. Test Firm Registration Number: 406779. • Industry Canada (IC) Two 3m Semi-anechoic chambers and the 10m Semi-anechoic chamber of SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch EMC Lab have been registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 4620C-1, 4620C-2, 4620C-3. 4.6 Deviation from Standards None 4.7 Abnormalities from Standard Conditions None This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180700631002 Page: 7 of 19 5 Equipment List Conducted Emissions at Mains Terminals (150kHz-30MHz) Equipment Manufacturer Model No Inventory No Cal Date Cal Due Date Shielding Room ChangZhou ZhongYu GB-88 SEM001-06 2017-05-10 2020-05-09 Measurement Software AUDIX e3 V5.4.1221d N/A N/A N/A Coaxial Cable SGS N/A SEM024-01 2018-07-12 2019-07-11 LISN Rohde & Schwarz ENV216 SEM007-01 2017-09-27 2018-09-26 LISN ETS-LINDGREN 3816/2 SEM007-02 2018-04-02 2019-04-01 EMI Test Receiver Rohde & Schwarz ESCI SEM004-02 2018-04-02 2019-04-01 Radiated Emissions (30MHz-1GHz) Equipment Manufacturer Model No Inventory No Cal Date Cal Due Date 10m Semi-Anechoic SAEMC FSAC1018 SEM001-03 2018-03-31 2021-03-30 Chamber e3 V8.2014-6- Measurement Software AUDIX N/A N/A N/A 27 Coaxial Cable SGS N/A SEM029-01 2018-07-12 2019-07-11 EMI Test Receiver Rohde & Schwarz ESR SEM004-03 2018-04-02 2019-04-01 (9kHz-7GHz) Trilog-Broadband Schwarzbeck VULB9168 SEM003-18 2016-06-29 2019-06-28 Antenna(30MHz-1GHz) Sonoma Instrument Pre-amplifier 310N SEM005-04 2018-04-13 2019-04-12 Co General used equipment Equipment Manufacturer Model No Inventory No Cal Date Cal Due Date Shanghai Humidity/ Temperature Meteorological ZJ1-2B SEM002-03 2017-09-29 2018-09-28 Indicator Industry Factory Shanghai Humidity/ Temperature Meteorological ZJ1-2B SEM002-04 2017-09-29 2018-09-28 Indicator Industry Factory Humidity/ Temperature Mingle N/A SEM002-08 2017-09-29 2018-09-28 Indicator Changchun Barometer Meteorological DYM3 SEM002-01 2018-04-08 2019-04-07 Industry Factory This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180700631002 Page: 8 of 19 6 Emission Test Results 6.1 Conducted Emissions at Mains Terminals (150kHz-30MHz) Test Requirement: 47 CFR Part 15, Subpart B Test Method: ANSI C63.4:2014 Frequency Range: 150kHz to 30MHz Limit: 0.15M-0.5MHz 66dB(µV)-56dB(µV) quasi-peak, 56dB(µV)-46dB(µV) average 0.5M-5MHz 56dB(µV) quasi-peak, 46dB(µV) average 5M-30MHz 60dB(µV) quasi-peak, 50dB(µV) average Detector: Peak for pre-scan (9kHz resolution bandwidth) 0.15M to 30MHz 6.1.1 E.U.T. Operation Operating Environment: Temperature: 26.2 °C Humidity: 56.3 % RH Atmospheric Pressure: 1005 mbar Pretest these a: DC5V output mode, keep EUT working with full load. modes to find b: DC9V output mode, keep EUT working with full load. the worst case: c: DC12V output mode, keep EUT working with full load. The worst case a: DC5V output mode, keep EUT working with full load. for final test: b: DC9V output mode, keep EUT working with full load. c: DC12V output mode, keep EUT working with full load. 6.1.2 Test Setup Diagram 6.1.3 Measurement Data An initial pre-scan was performed with peak detector.Quasi-Peak or Average measurement were performed at the frequencies with maximized peak emission were detected. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180700631002 Page: 9 of 19 Mode:a; Line:Live Line This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180700631002 Page: 10 of 19 Mode:a; Line:Neutral Line This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180700631002 Page: 11 of 19 Mode:b; Line:Live Line This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180700631002 Page: 12 of 19 Mode:b; Line:Neutral Line This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180700631002 Page: 13 of 19 Mode:c; Line:Live Line This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180700631002 Page: 14 of 19 Mode:c; Line:Neutral Line This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180700631002 Page: 15 of 19 6.2 Radiated Emissions (30MHz-1GHz) Test Requirement: 47 CFR Part 15, Subpart B Test Method: ANSI C63.4:2014 Frequency Range: 30MHz to 1GHz Measurement Distance: 10m Limit of 3m: 30MHz -88MHz 40(dBµV/m) quasi-peak 88MHz-216MHz 43.5(dBµV/m) quasi-peak 216MHz-960MHz 46(dBµV/m) quasi-peak 960MHz-1000MHz 54(dBµV/m) quasi-peak Detector: Peak for pre-scan (120kHz resolution bandwidth) 30M to1000MHz 6.2.1 E.U.T. Operation Operating Environment: Temperature: 25 °C Humidity: 51 % RH Atmospheric Pressure: 1005 mbar Pretest these a: DC5V output mode, keep EUT working with full load. modes to find b: DC9V output mode, keep EUT working with full load. the worst case: c: DC12V output mode, keep EUT working with full load. The worst case a: DC5V output mode, keep EUT working with full load. for final test: b: DC9V output mode, keep EUT working with full load. c: DC12V output mode, keep EUT working with full load. 6.2.2 Test Setup Diagram 6.2.3 Measurement Data An initial pre-scan was performed in the chamber using the spectrum analyser in peak detection mode. Quasi-peak measurements were conducted based on the peak sweep graph. The EUT was measured by BiConiLog antenna with 2 orthogonal polarities. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180700631002 Page: 16 of 19 Mode: a Radiated Emissions Polarization Frequency Cable_ Antenna Pre- Reading Net Limit Margin (MHz) Loss (dB) Factor Amp at 10m at 3m at 3m (dB) (dB) Gain (dBµV) (dBµV/m) (dBµV/m) (dB) Horizontal 43.050 6.85 13.06 32.46 26.59 24.50 40.00 -15.50 Horizontal 164.908 7.50 12.91 32.42 28.63 27.08 43.50 -16.42 Horizontal 271.325 7.91 11.89 32.37 28.18 26.07 46.00 -19.93 Horizontal 495.934 8.59 16.74 32.35 26.61 30.05 46.00 -15.95 Horizontal 609.922 8.90 18.91 32.36 27.42 33.33 46.00 -12.67 Horizontal 758.041 9.21 20.86 32.22 27.85 36.16 46.00 -9.84 Vertical 54.261 6.96 12.43 32.45 30.10 27.50 40.00 -12.50 Vertical 97.456 7.19 9.22 32.47 32.42 26.82 43.50 -16.68 Vertical 157.007 7.47 13.40 32.42 30.34 29.25 43.50 -14.25 Vertical 210.048 7.67 9.53 32.40 31.21 26.47 43.50 -17.03 Vertical 334.859 8.12 13.56 32.35 26.88 26.67 46.00 -19.33 Vertical 499.425 8.60 16.78 32.35 27.63 31.12 46.00 -14.88 NOTES: 1. Quasi-Peak detector is used except for others stated. 2. All measurements were made at 10 meters. 3. Negative value in the margin column shows emission below limit. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180700631002 Page: 17 of 19 Mode: b Radiated Emissions Polarization Frequency Cable_ Antenna Pre- Reading Net Limit Margin (MHz) Loss (dB) Factor Amp at 10m at 3m at 3m (dB) (dB) Gain (dBµV) (dBµV/m) (dBµV/m) (dB) Horizontal 40.135 6.82 13.31 32.46 27.18 25.31 40.00 -14.69 Horizontal 52.760 6.94 12.55 32.45 27.53 25.03 40.00 -14.97 Horizontal 165.487 7.50 12.85 32.42 28.41 26.80 43.50 -16.70 Horizontal 326.740 8.10 13.40 32.35 27.32 26.93 46.00 -19.07 Horizontal 530.101 8.69 17.37 32.36 27.43 31.59 46.00 -14.41 Horizontal 827.493 9.35 21.43 32.00 27.32 36.56 46.00 -9.44 Vertical 45.855 6.88 12.88 32.45 29.73 27.50 40.00 -12.50 Vertical 52.208 6.94 12.60 32.45 29.30 26.85 40.00 -13.15 Vertical 100.934 7.20 9.49 32.47 32.77 27.45 43.50 -16.05 Vertical 161.474 7.49 13.24 32.42 35.34 34.11 43.50 -9.39 Vertical 203.523 7.64 9.38 32.40 31.94 27.02 43.50 -16.48 Vertical 296.184 8.00 12.57 32.36 29.63 28.30 46.00 -17.70 NOTES: 1. Quasi-Peak detector is used except for others stated. 2. All measurements were made at 10 meters. 3. Negative value in the margin column shows emission below limit. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180700631002 Page: 18 of 19 Mode: c Radiated Emissions Polarization Frequency Cable_ Antenna Pre- Reading Net Limit Margin (MHz) Loss (dB) Factor Amp at 10m at 3m at 3m (dB) (dB) Gain (dBµV) (dBµV/m) (dBµV/m) (dB) Horizontal 42.302 6.84 13.12 32.46 27.85 25.81 40.00 -14.19 Horizontal 164.908 7.50 12.91 32.42 28.09 26.54 43.50 -16.96 Horizontal 241.676 7.80 11.10 32.38 27.12 24.10 46.00 -21.90 Horizontal 350.477 8.17 13.85 32.35 27.40 27.53 46.00 -18.47 Horizontal 614.214 8.91 19.00 32.36 27.64 33.65 46.00 -12.35 Horizontal 787.851 9.27 21.15 32.18 27.20 35.90 46.00 -10.10 Vertical 45.058 6.87 12.90 32.46 29.39 27.16 40.00 -12.84 Vertical 55.609 6.97 12.33 32.45 29.81 27.12 40.00 -12.88 Vertical 101.289 7.20 9.52 32.47 33.28 27.99 43.50 -15.51 Vertical 157.007 7.47 13.40 32.42 33.05 31.96 43.50 -11.54 Vertical 191.745 7.59 9.70 32.40 33.21 28.56 43.50 -14.94 Vertical 325.596 8.10 13.38 32.35 27.35 26.94 46.00 -19.06 NOTES: 1. Quasi-Peak detector is used except for others stated. 2. All measurements were made at 10 meters. 3. Negative value in the margin column shows emission below limit. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180700631002 Page: 19 of 19 7 Photographs Please refer to attached “EUT Photos and Test setups” - End of the Report - This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.


Document Created: 2018-11-16 06:24:39
Document Modified: 2018-11-16 06:24:39
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC