12247888-S1V2 FCC Report SAR

FCC ID: PY7-72474U

RF Exposure Info

Download: PDF
FCCID_3849105

SAR EVALUATION REPORT PERMISSIVE CHANGE FCC 47 CFR § 2.1093 IEEE Std 1528-2013 For GSM/WCDMA/LTE Phone with BT, DTS/UNII a/b/g/n/ac & NFC FCC ID: PY7-72474U Report Number: 12247888-S1V2 Issue Date: 5/10/2018 Prepared for SONY MOBILE COMMUNICATIONS INC. 4-12-3 HIGASHI-SHINAGAWA SHINAGAWA-KU,TOKYO, 140-0002, JAPAN Prepared by UL VERIFICATION SERVICES INC. 47173 BENICIA STREET FREMONT, CA 94538, U.S.A. TEL: (510) 771-1000 FAX: (510) 661-0888 NVLAP LAB CODE 200065-0

Report No.: 12247888-S1V2 Issue Date: 5/10/2018 Revision History Rev. Date Revisions Revised By V1 4/11/2018 Initial Issue -- V2 5/10/2018 Sec. 1, 6.1, 10.1 and 12 : Updated. Art Thammanavarat Page 2 of 25 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 12247888-S1V2 Issue Date: 5/10/2018 Table of Contents 1. Attestation of Test Results ......................................................................................................... 4 2. Test Specification, Methods and Procedures............................................................................ 5 3. Facilities and Accreditation ........................................................................................................ 5 4. SAR Measurement System & Test Equipment .......................................................................... 6 4.1. SAR Measurement System ........................................................................................................ 6 4.2. SAR Scan Procedures ............................................................................................................... 7 4.3. Test Equipment.......................................................................................................................... 9 5. Measurement Uncertainty ......................................................................................................... 10 6. Device Under Test (DUT) Information ...................................................................................... 11 6.1. DUT Description ...................................................................................................................... 11 6.2. Wireless Technologies ............................................................................................................. 12 7. RF Exposure Conditions (Test Configurations) ...................................................................... 13 8. Dielectric Property Measurements & System Check .............................................................. 14 8.1. Dielectric Property Measurements ........................................................................................... 14 8.2. System Check.......................................................................................................................... 16 9. Conducted Output Power Measurements................................................................................ 17 9.1. Wi-Fi 5GHz (U-NII Bands)........................................................................................................ 17 10. Measured and Reported (Scaled) SAR Results ....................................................................... 19 10.1. Wi-Fi (U-NII Band) ................................................................................................................ 21 11. SAR Measurement Variability ................................................................................................... 22 12. Simultaneous Transmission SAR Analysis ............................................................................. 23 12.1. Sum of the SAR for WWAN & Wi-Fi & BT............................................................................. 24 Appendixes .......................................................................................................................................... 25 12247888-S1V1 Appendix A: SAR Setup Photos ............................................................................... 25 12247888-S1V1 Appendix B: SAR System Check Plots..................................................................... 25 12247888-S1V1 Appendix C: Highest SAR Test Plots ....................................................................... 25 12247888-S1V1 Appendix D: SAR Liquid Tissue Ingredients ............................................................. 25 12247888-S1V1 Appendix E: SAR Probe Calibration Certificates ...................................................... 25 12247888-S1V1 Appendix F: SAR Dipole Calibration Certificates ...................................................... 25 Page 3 of 25 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 12247888-S1V2 Issue Date: 5/10/2018 1. Attestation of Test Results Applicant Name SONY MOBILE COMMUNICATIONS INC. FCC ID PY7-72474U Applicable Standards FCC 47 CFR § 2.1093 Published RF exposure KDB procedures IEEE Std 1528-2013 SAR Limits (W/Kg) Exposure Category Peak spatial-average Product specific (1g of tissue) (10g of tissue) General population / 1.6 4 Uncontrolled exposure Equipment Class - Highest Reported SAR (W/kg) RF Exposure Conditions PCE DTS NII DSS Head N/A N/A 0.269 N/A Body-worn N/A N/A 0.022 N/A Hotspot/Wi-Fi Direct N/A N/A N/A N/A Product specific 10g SAR N/A N/A 0.071 N/A Simultaneous TX N/A N/A 0.688 N/A Date Tested 4/9/2018 to 4/11/2018 Test Results Pass Note: The proposed Permissive Change requires SAR testing for WLAN 5GHz chain 0 due to antenna gain differences from the original model. The SAR measurement results from the original filing can be found in FCC SAR report 12097277-S1. This report only contains the SAR values for the modified WLAN 5GHz chain 0 bands. Please refer to the original filling for the highest SAR values. The WWAN, WLAN 2.4GHz, WLAN 5GHz chain 1, and BT results from the original filling have been used in this report for simultaneous transmission analysis. The WWAN, WLAN 2.4GHz, and BT results from the original filling are listed above. UL Verification Services Inc. tested the above equipment in accordance with the requirements set forth in the above standards. All indications of Pass/Fail in this report are opinions expressed by UL Verification Services Inc. based on interpretations and/or observations of test results. Measurement Uncertainties were not taken into account and are published for informational purposes only. The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. Note: The results documented in this report apply only to the tested sample, under the conditions and modes of operation as described herein. This document may not be altered or revised in any way unless done so by UL Verification Services Inc. and all revisions are duly noted in the revisions section. Any alteration of this document not carried out by UL Verification Services Inc. will constitute fraud and shall nullify the document. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, any agency of the Federal Government, or any agency of any government (NIST Handbook 150, Annex A). This report is written to support regulatory compliance of the applicable standards stated above. Approved & Released By: Prepared By: Devin Chang Chakrit Thammanavarat Senior Test Engineer Test Engineer UL Verification Services Inc. UL Verification Services Inc. Page 4 of 25 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 12247888-S1V2 Issue Date: 5/10/2018 2. Test Specification, Methods and Procedures The tests documented in this report were performed in accordance with FCC 47 CFR § 2.1093, IEEE STD 1528- 2013, the following FCC Published RF exposure KDB procedures: o 248227 D01 802.11 Wi-Fi SAR v02r02 o 447498 D01 General RF Exposure Guidance v06 o 447498 D03 Supplement C Cross-Reference v01 o 648474 D04 Handset SAR v01r03 o 865664 D01 SAR measurement 100 MHz to 6 GHz v01r04 o 865664 D02 RF Exposure Reporting v01r02 o 941225 D06 Hotspot Mode v02r01 3. Facilities and Accreditation The test sites and measurement facilities used to collect data are located at 47173 Benicia Street 47266 Benicia Street SAR Lab A SAR Lab 1 SAR Lab B SAR Lab 2 SAR Lab C SAR Lab 3 SAR Lab D SAR Lab 4 SAR Lab E SAR Lab F SAR Lab G SAR Lab H UL Verification Services Inc. is accredited by NVLAP, Laboratory Code 200065-0. Page 5 of 25 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 12247888-S1V2 Issue Date: 5/10/2018 4. SAR Measurement System & Test Equipment 4.1. SAR Measurement System The DASY5 system used for performing compliance tests consists of the following items: • A standard high precision 6-axis robot with controller, teach pendant and software. An arm extension for accommodating the data acquisition electronics (DAE). • An isotropic Field probe optimized and calibrated for the targeted measurement. • A data acquisition electronics (DAE) which performs the signal amplification, signal multiplexing, AD- conversion, offset measurements, mechanical surface detection, collision detection, etc. The unit is battery powered with standard or rechargeable batteries. The signal is optically transmitted to the EOC. • The Electro-optical converter (EOC) performs the conversion from optical to electrical signals for the digital communication to the DAE. To use optical surface detection, a special version of the EOC is required. The EOC signal is transmitted to the measurement server. • The function of the measurement server is to perform the time critical tasks such as signal filtering, control of the robot operation and fast movement interrupts. • The Light Beam used is for probe alignment. This improves the (absolute) accuracy of the probe positioning. • A computer running WinXP or Win7 and the DASY5 software. • Remote control and teach pendant as well as additional circuitry for robot safety such as warning lamps, etc. • The phantom, the device holder and other accessories according to the targeted measurement. Page 6 of 25 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 12247888-S1V2 Issue Date: 5/10/2018 4.2. SAR Scan Procedures Step 1: Power Reference Measurement The Power Reference Measurement and Power Drift Measurements are for monitoring the power drift of the device under test in the batch process. The minimum distance of probe sensors to surface determines the closest measurement point to phantom surface. The minimum distance of probe sensors to surface is 2.1 mm. This distance cannot be smaller than the distance of sensor calibration points to probe tip as defined in the probe properties. Step 2: Area Scan The Area Scan is used as a fast scan in two dimensions to find the area of high field values, before doing a fine measurement around the hot spot. The sophisticated interpolation routines implemented in DASY software can find the maximum locations even in relatively coarse grids. When an Area Scan has measured all reachable points, it computes the field maximal found in the scanned area, within a range of the global maximum. The range (in dB) is specified in the standards for compliance testing. For example, a 2 dB range is required in IEEE Standard 1528 and IEC 62209 standards, whereby 3 dB is a requirement when compliance is assessed in accordance with the ARIB standard (Japan). If only one Zoom Scan follows the Area Scan, then only the absolute maximum will be taken as reference. For cases where multiple maximums are detected, the number of Zoom Scans has to be increased accordingly. Area Scan Parameters extracted from KDB 865664 D01 SAR Measurement 100 MHz to 6 GHz Page 7 of 25 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 12247888-S1V2 Issue Date: 5/10/2018 Step 3: Zoom Scan Zoom Scans are used to assess the peak spatial SAR values within a cubic averaging volume containing 1 g and 10 g of simulated tissue. The Zoom Scan measures points (refer to table below) within a cube whose base faces are centered on the maxima found in a preceding area scan job within the same procedure. When the measurement is done, the Zoom Scan evaluates the averaged SAR for 1 g and 10 g and displays these values next to the job’s label. Zoom Scan Parameters extracted from KDB 865664 D01 SAR Measurement 100 MHz to 6 GHz Step 4: Power drift measurement The Power Drift Measurement measures the field at the same location as the most recent power reference measurement within the same procedure, and with the same settings. The Power Drift Measurement gives the field difference in dB from the reading conducted within the last Power Reference Measurement. This allows a user to monitor the power drift of the device under test within a batch process. The measurement procedure is the same as Step 1. Step 5: Z-Scan (FCC only) The Z Scan measures points along a vertical straight line. The line runs along the Z-axis of a one-dimensional grid. In order to get a reasonable extrapolation the extrapolated distance should not be larger than the step size in Z- direction. Page 8 of 25 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 12247888-S1V2 Issue Date: 5/10/2018 4.3. Test Equipment The measuring equipment used to perform the tests documented in this report has been calibrated in accordance with the manufacturers’ recommendations, and is traceable to recognized national standards. Dielectric Property Measurements Name of Equipment Manufacturer Type/Model Serial No. Cal. Due Date Network Analyzer Agilent 8753ES MY40001647 9/15/2018 Dielectric Probe kit SPEAG DAK-3.5 1087 11/14/2018 Shorting block SPEAG DAK-3.5 Short SM DAK 200 BA 11/14/2018 Thermometer Traceable Calibration Control Co. 4242 150378159 5/26/2018 System Check Name of Equipment Manufacturer Type/Model Serial No. Cal. Due Date Synthesized Signal Generator Agilent N5181A MY50140630 5/16/2018 Power Meter HP 437B 3125U12345 8/10/2018 Power Meter HP 437B 3125U11347 8/15/2018 Power Sensor HP 8481A 3318A92374 8/15/2018 Power Sensor HP 8481A 1926A27048 8/10/2018 Amplifier MITEQ AMF-4D-00400600-50-30P 1795092 N/A Directional coupler Werlatone C8060-102 2141 N/A DC Power Supply BK Precision 1611 215-02292 N/A Lab Equipment Name of Equipment Manufacturer Type/Model Serial No. Cal. Due Date E-Field Probe (SAR Lab G) SPEAG EX3DV4 3871 8/23/2018 Data Acquisition Electronics (SAR Lab G) SPEAG DAE4 1359 2/9/2019 System Validation Dipole SPEAG D5GHzV2 1003 3/13/2019 Other Name of Equipment Manufacturer Type/Model T Number Serial No. Cal. Due Date Power Meter Keysight N1912A T229 MY45100242 8/14/2018 Power Sensor* Agilent N1921A T1223 MY55120015 3/29/2018 DC Power Supply HP 6296A N/A 2841A-05955 N/A Note(s): *Equipment not used past calibration due date. Page 9 of 25 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 12247888-S1V2 Issue Date: 5/10/2018 5. Measurement Uncertainty Per KDB 865664 D01 SAR Measurement 100 MHz to 6 GHz, when the highest measured 1-g SAR within a frequency band is < 1.5 W/kg and the measured 10-g SAR within a frequency band is < 3.75 W/kg. The expanded SAR measurement uncertainty must be ≤ 30%, for a confidence interval of k = 2. If these conditions are met, extensive SAR measurement uncertainty analysis described in IEEE Std 1528-2013 is not required in SAR reports submitted for equipment approval. Therefore, the measurement uncertainty is not required. Page 10 of 25 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 12247888-S1V2 Issue Date: 5/10/2018 6. Device Under Test (DUT) Information 6.1. DUT Description The proposed Permissive Change requires SAR testing for WLAN 5GHz chain 0 due to antenna gain differences from the original model. The SAR measurement results from the original filing can be found in FCC SAR report 12097277-S1. This report only contains the SAR values for the modified WLAN 5GHz chain 0 bands. Please refer to the original filling for the highest SAR values. The WWAN, WLAN 2.4GHz, WLAN 5GHz chain 1, and BT results from the original filling have been used in this report for simultaneous transmission analysis. The WWAN, WLAN 2.4GHz, and BT results from the original filling are listed above. Device Dimension Please refer to Appendix A Back Cover ☒ The Back Cover is not removable. Battery Options ☒ The rechargeable battery is not user accessible. Accessory Headset Wi-Fi Hotspot mode permits the device to share its cellular data connection with other Wi-Fi-enabled devices. Wireless Router ☒ Mobile Hotspot (Wi-Fi 2.4 GHz) (Hotspot) ☐ Mobile Hotspot (Wi-Fi 5 GHz) Wi-Fi Direct enabled devices transfer data directly between each other Wi-Fi Direct ☒ Wi-Fi Direct (Wi-Fi 2.4 GHz) ☐ Wi-Fi Direct (Wi-Fi 5 GHz) S/N Technology Notes BH90007VAY WLAN - 5GHz #1 Conducted Test sample BH90009SAY WLAN - 5GHz Radiated information BH900096AY WLAN - 5GHz Radiated BH9000A9AY WLAN - 5GHz Radiated Hardware Version A Software Version 0.202 Page 11 of 25 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 12247888-S1V2 Issue Date: 5/10/2018 6.2. Wireless Technologies Wireless Duty Cycle used for SAR Frequency bands Operating mode technologies testing Multi-Slot Class: GSM Voice: 12.5% Voice (GMSK) ☐ Class 8 - 1 Up, 4 Down (E)GPRS: 1 Slot: 12.5% 850 GPRS (GMSK) ☐ Class 10 - 2 Up, 4 Down 2 Slots: 25% GSM 1900 EGPRS (8PSK) ☐ Class 12 - 4 Up, 4 Down 3 Slots: 37.5% ☒ Class 33 - 4 Up, 5 Down 4 Slots: 50% Does this device support DTM (Dual Transfer Mode)? ☒ Yes ☐ No UMTS Rel. 99 (Voice & Data) Band II HSDPA (Rel. 5) W-CDMA Band IV HSUPA (Rel. 6) 100% (UMTS) Band V HSPA+ (Rel. 9) DC-HSDPA (Rel. 9) FDD Band 2 FDD Band 4 FDD Band 5 QPSK FDD Band 7 16QAM FDD Band 12 64AQM 100% (FDD) FDD Band 13 LTE Rel. 12 Carrier Aggregation 4CC (1 Uplink and 4 63.3% (TDD) 2 FDD Band 17 Downlinks) FDD Band 26 FDD Band 29 (Rx Only) TDD Band 41 FDD Band 66 Does this device support SV-LTE (1xRTT-LTE)? ☐ Yes ☒ No 802.11b 99.03% (802.11b) 1 2.4 GHz 802.11g 98.31% (802.11g) 1 802.11n (HT20) 97.10% (802.11n) 1 802.11a 802.11n (HT20) 98.1% (802.11a) 1 Wi-Fi 802.11n (HT40) 96.9% (802.11n HT20) 1 5 GHz 802.11ac (VHT20) 89.5% (802.11n HT40) 1 802.11ac (VHT40) 84.5% (802.11ac VHT80) 1 802.11ac (VHT80) Does this device support bands 5.60 ~ 5.65 GHz? ☒ Yes ☐ No Does this device support Band gap channel(s)? ☒ Yes ☐ No Bluetooth 2.4 GHz Version 5.0 LE 76.93%(DH5) Notes: 1. Duty cycle for Wi-Fi is referenced from the DTS and UNII report. 2. This device supports uplink-downlink configuration 0-6. The configuration with the highest duty cycle was used (Subframe Number 0 at 63.3%). Page 12 of 25 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 12247888-S1V2 Issue Date: 5/10/2018 7. RF Exposure Conditions (Test Configurations) Refer to Appendix A for the specific details of the antenna-to-antenna and antenna-to-edge(s) distances. Wireless RF Exposure DUT-to-User Test Antenna-to- SAR technologies Conditions Separation Position edge/surface Required Left Touch N/A Yes Left Tilt (15°) N/A Yes Head 0 mm Right Touch N/A Yes Right Tilt (15°) N/A Yes Rear N/A Yes Body 15 mm WLAN/BT Front N/A Yes (Chain 0) Rear < 25 mm Yes Front < 25 mm Yes Product specific Edge 1 (Top) < 25 mm Yes 0 mm (5 GHz bands only) Edge 2 (Right) > 25 mm No Edge 3 (Bottom) > 25 mm No Edge 4 (Left) < 25 mm Yes Notes: 1. SAR is not required because the distance from the antenna to the edge is > 25 mm as per KDB 941225 D06 Hot Spot SAR. 2. When Hotspot Mode is not supported, 10-g Extremity SAR is required for all surfaces and edges with an antenna located at ≤ 25 mm from that surface or edge in direct contact with a flat phantom, to address interactive hand use exposure conditions. 3. When hotspot mode applies, 10-g extremity SAR is required only for the surfaces and edges with hotspot mode 1-g reported SAR > 1.2 W/kg. 4. The WWAN Sub Antenna does not support FCC bands. Page 13 of 25 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 12247888-S1V2 Issue Date: 5/10/2018 8. Dielectric Property Measurements & System Check 8.1. Dielectric Property Measurements The temperature of the tissue-equivalent medium used during measurement must also be within 18C to 25C and within ± 2C of the temperature when the tissue parameters are characterized. The dielectric parameters must be measured before the tissue-equivalent medium is used in a series of SAR measurements. The parameters should be re-measured after each 3 – 4 days of use; or earlier if the dielectric parameters can become out of tolerance; for example, when the parameters are marginal at the beginning of the measurement series. Tissue dielectric parameters were measured at the low, middle and high frequency of each operating frequency range of the test device. The dielectric constant (εr) and conductivity (σ) of typical tissue-equivalent media recipes are expected to be within ± 5% of the required target values; but for SAR measurement systems that have implemented the SAR error compensation algorithms documented in IEEE Std 1528-2013, to automatically compensate the measured SAR results for deviations between the measured and required tissue dielectric parameters, the tolerance for εr and σ may be relaxed to ± 10%. This is limited to frequencies ≤ 3 GHz. Tissue Dielectric Parameters FCC KDB 865664 D01 SAR Measurement 100 MHz to 6 GHz Head Body Target Frequency (MHz) er s (S/m) er s (S/m) 150 52.3 0.76 61.9 0.80 300 45.3 0.87 58.2 0.92 450 43.5 0.87 56.7 0.94 835 41.5 0.90 55.2 0.97 900 41.5 0.97 55.0 1.05 915 41.5 0.98 55.0 1.06 1450 40.5 1.20 54.0 1.30 1610 40.3 1.29 53.8 1.40 1800 – 2000 40.0 1.40 53.3 1.52 2450 39.2 1.80 52.7 1.95 3000 38.5 2.40 52.0 2.73 5000 36.2 4.45 49.3 5.07 5100 36.1 4.55 49.1 5.18 5200 36.0 4.66 49.0 5.30 5300 35.9 4.76 48.9 5.42 5400 35.8 4.86 48.7 5.53 5500 35.6 4.96 48.6 5.65 5600 35.5 5.07 48.5 5.77 5700 35.4 5.17 48.3 5.88 5800 35.3 5.27 48.2 6.00 IEEE Std 1528-2013 Refer to Table 3 within the IEEE Std 1528-2013 Page 14 of 25 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 12247888-S1V2 Issue Date: 5/10/2018 Dielectric Property Measurements Results: Relative Permittivity (єr) Conductivity (σ) SAR Band Tissue Frequency Date Delta Delta Lab (MHz) Type (MHz) Measured Target Measured Target (%) (%) 5250 36.24 35.93 0.85 4.63 4.70 -1.49 G 4/9/2018 5250 Head 5150 36.35 36.05 0.84 4.50 4.60 -2.28 5350 36.24 35.82 1.18 4.63 4.80 -3.59 5250 49.07 48.95 0.24 5.39 5.35 0.71 G 4/9/2018 5250 Body 5150 49.20 49.09 0.23 5.21 5.24 -0.49 5350 48.96 48.82 0.29 5.52 5.47 0.98 5600 35.56 35.53 0.07 5.04 5.06 -0.50 G 4/9/2018 5600 Head 5500 35.81 35.65 0.45 4.88 4.96 -1.61 5725 35.51 35.39 0.34 5.15 5.19 -0.70 5600 48.22 48.48 -0.53 5.95 5.76 3.28 G 4/9/2018 5600 Body 5500 48.62 48.61 0.01 5.73 5.64 1.57 5725 48.14 48.31 -0.35 6.11 5.91 3.36 5750 35.40 35.36 0.11 5.17 5.21 -0.76 G 4/9/2018 5750 Head 5700 35.37 35.42 -0.14 5.11 5.16 -0.98 5850 35.18 35.30 -0.34 5.30 5.27 0.51 5750 48.12 48.27 -0.32 6.17 5.94 3.89 G 4/9/2018 5750 Body 5700 48.12 48.34 -0.46 6.03 5.88 2.58 5850 47.86 48.20 -0.71 6.29 6.00 4.75 Page 15 of 25 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 12247888-S1V2 Issue Date: 5/10/2018 8.2. System Check SAR system verification is required to confirm measurement accuracy, according to the tissue dielectric media, probe calibration points and other system operating parameters required for measuring the SAR of a test device. The system verification must be performed for each frequency band and within the valid range of each probe calibration point required for testing the device. The same SAR probe(s) and tissue-equivalent media combinations used with each specific SAR system for system verification must be used for device testing. When multiple probe calibration points are required to cover substantially large transmission bands, independent system verifications are required for each probe calibration point. A system verification must be performed before each series of SAR measurements using the same probe calibration point and tissue-equivalent medium. Additional system verification should be considered according to the conditions of the tissue-equivalent medium and measured tissue dielectric parameters, typically every three to four days when the liquid parameters are re-measured or sooner when marginal liquid parameters are used at the beginning of a series of measurements. System Performance Check Measurement Conditions: • The measurements were performed in the flat section of the TWIN SAM or ELI phantom, shell thickness: 2.0 ±0.2 mm (bottom plate) filled with Body or Head simulating liquid of the following parameters. • The depth of tissue-equivalent liquid in a phantom must be ≥ 15.0 cm for SAR measurements ≤ 3 GHz and ≥ 10.0 cm for measurements > 3 GHz. • The DASY system with an E-Field Probe was used for the measurements. • The dipole was mounted on the small tripod so that the dipole feed point was positioned below the center marking of the flat phantom section and the dipole was oriented parallel to the body axis (the long side of the phantom). The standard measuring distance was 10 mm (above 1 GHz) and 15 mm (below 1 GHz) from dipole center to the simulating liquid surface. • The coarse grid with a grid spacing of 15 mm was aligned with the dipole. For 5 GHz band - The coarse grid with a grid spacing of 10 mm was aligned with the dipole. • Special 7x7x7 (below 3 GHz) and/or 8x8x7 (above 3 GHz) fine cube was chosen for the cube. • Distance between probe sensors and phantom surface was set to 3 mm. For 5 GHz band - Distance between probe sensors and phantom surface was set to 2.5 mm • The dipole input power (forward power) was 100 mW. • The results are normalized to 1 W input power. System Check Results The 1-g and 10-g SAR measured with a reference dipole, using the required tissue-equivalent medium at the test frequency, must be within 10% of the manufacturer calibrated dipole SAR target. Measured Results for 1g SAR Measured Results for 10g SAR SAR Tissue Dipole Type Dipole Plot Date Lab Type _Serial # Cal. Due Data Zoom Scan Normalize Target Delta Zoom Scan Normalize Target Delta No. to 100 mW to 1 W (Ref. Value) ±10 % to 100 mW to 1 W (Ref. Value) ±10 % G 4/9/2018 Head D5GHzV2 SN:1003 (5.25 GHz) 3/13/2019 7.690 76.90 80.60 -4.59 2.190 21.90 23.20 -5.60 G 4/9/2018 Body D5GHzV2 SN:1003 (5.25 GHz) 3/13/2019 7.540 75.40 73.60 2.45 2.110 21.10 20.50 2.93 G 4/9/2018 Head D5GHzV2 SN:1003 (5.60 GHz) 3/13/2019 8.200 82.00 84.50 -2.96 2.320 23.20 24.00 -3.33 G 4/9/2018 Body D5GHzV2 SN:1003 (5.60 GHz) 3/13/2019 8.350 83.50 77.70 7.46 2.320 23.20 21.70 6.91 G 4/9/2018 Head D5GHzV2 SN:1003 (5.75 GHz) 3/13/2019 7.060 70.60 78.40 -9.95 2.020 20.20 22.20 -9.01 1,2 G 4/9/2018 Body D5GHzV2 SN:1003 (5.75 GHz) 3/13/2019 7.350 73.50 73.90 -0.54 2.050 20.50 20.60 -0.49 Page 16 of 25 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 12247888-S1V2 Issue Date: 5/10/2018 9. Conducted Output Power Measurements 9.1. Wi-Fi 5GHz (U-NII Bands) Measured Results Meas. Avg Pwr Max Output Power Band Freq. SAR Test Mode Data Rate Ch # (dBm) (dBm) (GHz) (MHz) (Yes/No) Chain 0 Chain 0 36 5180 40 5200 802.11a 6 Mbps 12.2 No 44 5220 48 5240 36 5180 802.11n 40 5200 6.5 Mbps 12.2 No (HT20) 44 5220 48 5240 5.2 802.11n 38 5190 Not Required U-NII 1 13.5 Mbps 12.2 No (HT40) 46 5230 36 5180 802.11ac 40 5200 6.5 Mbps 12.3 No (VHT20) 44 5220 48 5240 802.11ac 38 5190 13.5 Mbps 12.3 No (VHT40) 46 5230 802.11ac (VHT80) 29.3 Mbps 42 5210 12.2 No 52 5260 11.7 56 5280 11.7 802.11a 6 Mbps 12.5 Yes 60 5300 12.1 64 5320 11.6 52 5260 802.11n 56 5280 6.5 Mbps 12.4 No (HT20) 60 5300 64 5320 5.3 802.11n 54 5270 U-NII-2A 13.5 Mbps 12.4 Yes (HT40) 62 5310 52 5260 Not Required 802.11ac 56 5280 6.5 Mbps 12.2 No (VHT20) 60 5300 64 5320 802.11ac 54 5270 13.5 Mbps 12.2 No (VHT40) 62 5310 802.11ac (VHT80) 29.3 Mbps 58 5290 12.1 No Note(s): 1. For “Not required”, SAR Test reduction was applied from KDB 248227 guidance, Sec. 2.1, b), 1) when the same maximum power is specified for multiple transmission modes in a frequency band, the largest channel bandwidth, lowest order modulation, lowest data rate and lowest order 802.11a/g/n/ac mode is used for SAR measurement, on the highest measured output power channel in the initial test configuration, for each frequency band. Additional output power measurements were not deemed necessary. 2. When the same transmission mode configurations have the same maximum output power on the same channel for the 802.11 a/g/n/ac modes, the channel in the lower order/sequence 802.11 mode (i.e. a, g, n then ac) is selected. 3. When the specified maximum output power is the same for both UNII band I and UNII band 2A, begin SAR measurement in UNII band 2A; and if the highest reported SAR for UNII band 2A is o ≤ 1.2 W/kg, SAR is not required for UNII band I o > 1.2 W/kg, both bands should be tested independently for SAR. Page 17 of 25 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 12247888-S1V2 Issue Date: 5/10/2018 Meas. Avg Pwr Max Output Power Band Freq. SAR Test Mode Data Rate Ch # (dBm) (dBm) (GHz) (MHz) (Yes/No) Chain 0 Chain 0 100 5500 116 5580 802.11a 6 Mbps 10.4 No 124 5620 144 5720 Not Required 100 5500 802.11n 116 5580 6.5 Mbps 10.4 Yes (HT20) 124 5620 144 5720 102 5510 9.3 802.11n 118 5590 9.4 13.5 Mbps 10.4 Yes (HT40) 126 5630 9.2 5.5 142 5710 9.6 U-NII-2C 100 5500 802.11ac 116 5580 6.5 Mbps 10.1 No (VHT20) 124 5620 144 5720 102 5510 802.11ac 118 5590 Not Required 13.5 Mbps 10.1 No (VHT40) 126 5630 142 5710 106 5530 802.11ac 29.3 Mbps 122 5610 10.1 No (VHT80) 138 5690 149 5745 10.4 802.11a 6 Mbps 157 5785 10.3 11.5 Yes 165 5825 10.4 149 5745 802.11n 6.5 Mbps 157 5785 10.4 No (HT20) 165 5825 5.8 802.11n 151 5755 13.5 Mbps 10.4 No U-NII-3 (HT40) 159 5795 149 5745 Not Required 802.11ac 6.5 Mbps 157 5785 10.9 No (VHT20) 165 5825 802.11ac 151 5755 13.5 Mbps 10.9 No (VHT40) 159 5795 802.11ac 29.3 Mbps 155 5775 10.3 No (VHT80) Note(s): 1. For “Not required”, SAR Test reduction was applied from KDB 248227 guidance, Sec. 2.1, b), 1) when the same maximum power is specified for multiple transmission modes in a frequency band, the largest channel bandwidth, lowest order modulation, lowest data rate and lowest order 802.11a/g/n/ac mode is used for SAR measurement, on the highest measured output power channel in the initial test configuration, for each frequency band. Additional output power measurements were not deemed necessary. 2. When the same transmission mode configurations have the same maximum output power on the same channel for the 802.11 a/g/n/ac modes, the channel in the lower order/sequence 802.11 mode (i.e. a, g, n then ac) is selected. Page 18 of 25 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 12247888-S1V2 Issue Date: 5/10/2018 10. Measured and Reported (Scaled) SAR Results SAR Test Reduction criteria are as follows: Reported SAR(W/kg) for Wi-Fi and Bluetooth= Measured SAR * Tune-up scaling factor * Duty Cycle scaling factor KDB 447498 D01 General RF Exposure Guidance: Testing of other required channels within the operating mode of a frequency band is not required when the reported 1-g or 10-g SAR for the mid-band or highest output power channel is: • ≤ 0.8 W/kg or 2.0 W/kg, for 1-g or 10-g respectively, when the transmission band is ≤ 100 MHz • ≤ 0.6 W/kg or 1.5 W/kg, for 1-g or 10-g respectively, when the transmission band is between 100 MHz and 200 MHz • ≤ 0.4 W/kg or 1.0 W/kg, for 1-g or 10-g respectively, when the transmission band is ≥ 200 MHz KDB 648474 D04 Handset SAR: With headset attached, when the reported SAR for body-worn accessory, measured without a headset connected to the handset, is > 1.2 W/kg, the highest reported SAR configuration for that wireless mode and frequency band should be repeated for that body-worn accessory with a headset attached to the handset. KDB 648474 D04 Handset SAR (Phablet Only): When hotspot mode does not apply, 10-g Extremity SAR is required for all surfaces and edges with an antenna located at ≤ 25 mm from that surface or edge in direct contact with a flat phantom, to address interactive hand use exposure conditions. When hotspot mode applies, 10-g extremity SAR is required only for the surfaces and edges with hotspot mode 1-g reported SAR > 1.2 W/kg . Additional 1-g SAR testing at 5 mm is not required when hotspot mode 10-g extremity SAR is not required for the surfaces and edges; since all 1-g reported SAR < 1.2 W/kg. KDB 248227 D01 SAR meas for 802.11: SAR test reduction for 802.11 Wi-Fi transmission mode configurations are considered separately for DSSS and OFDM. An initial test position is determined to reduce the number of tests required for certain exposure configurations with multiple test positions. An initial test configuration is determined for each frequency band and aggregated band according to maximum output power, channel bandwidth, wireless mode configurations and other operating parameters to streamline the measurement requirements. For 2.4 GHz DSSS, either the initial test position or DSSS procedure is applied to reduce the number of SAR tests; these are mutually exclusive. For OFDM, an initial test position is only applicable to next to the ear, UMPC mini-tablet and hotspot mode configurations, which is tested using the initial test configuration to facilitate test reduction. For other exposure conditions with a fixed test position, SAR test reduction is determined using only the initial test configuration. The multiple test positions require SAR measurements in head, hotspot mode or UMPC mini-tablet configurations may be reduced according to the highest reported SAR determined using the initial test position(s) by applying the DSSS or OFDM SAR measurement procedures in the required wireless mode test configuration(s). The initial test position(s) is measured using the highest measured maximum output power channel in the required wireless mode test configuration(s). When the reported SAR for the initial test position is: • ≤ 0.4 W/kg, further SAR measurement is not required for the other test positions in that exposure configuration and wireless mode combination within the frequency band or aggregated band. DSSS and OFDM configurations are considered separately according to the required SAR procedures. • > 0.4 W/kg, SAR is repeated using the same wireless mode test configuration tested in the initial test position to measure the subsequent next closet/smallest test separation distance and maximum coupling test position, on the highest maximum output power channel, until the reported SAR is ≤ 0.8 W/kg or all required test positions are tested. o For subsequent test positions with equivalent test separation distance or when exposure is dominated by coupling conditions, the position for maximum coupling condition should be tested. o When it is unclear, all equivalent conditions must be tested. • For all positions/configurations tested using the initial test position and subsequent test positions, when the reported SAR is > 0.8 W/kg, measure the SAR for these positions/configurations on the subsequent next highest measured output power channel(s) until the reported SAR is ≤ 1.2 W/kg or all required test channels are considered. o The additional power measurements required for this step should be limited to those necessary for identifying subsequent highest output power channels to apply the test reduction. • When the specified maximum output power is the same for both UNII 1 and UNII 2A, begin SAR measurements in UNII 2A with the channel with the highest measured output power. If the reported SAR for UNII 2A is ≤ 1.2 W/kg, SAR is not required for UNII 1; otherwise treat the remaining bands separately and test them independently for SAR. Page 19 of 25 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 12247888-S1V2 Issue Date: 5/10/2018 • When the specified maximum output power is different between UNII 1 and UNII 2A, begin SAR with the band that has the higher specified maximum output. If the highest reported SAR for the band with the highest specified power is ≤ 1.2 W/kg, testing for the band with the lower specified output power is not required; otherwise test the remaining bands independently for SAR. To determine the initial test position, Area Scans were performed to determine the position with the Maximum Value of SAR (measured). The position that produced the highest Maximum Value of SAR is considered the worst case position; thus used as the initial test position. Page 20 of 25 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 12247888-S1V2 Issue Date: 5/10/2018 10.1. Wi-Fi (U-NII Band) U-NII-1 & U-NII-2A Area Scan Power (dBm) 1-g SAR (W/kg) RF Exposure Dist. Duty Cycle Plot Mode Antenna Test Position Ch #. Freq. (MHz) Max. SAR Tune-up Conditions (mm) Factor Meas. Meas. Scaled No. (W/kg) Limit Left Touch 60 5300 0.161 1.019 12.50 12.13 Left Tilt 60 5300 0.180 1.019 12.50 12.13 Head 802.11a Chain 0 0 Right Touch 60 5300 0.230 1.019 12.50 12.13 0.115 0.128 1 Right Tilt 60 5300 0.194 1.019 12.50 12.13 Rear 60 5300 0.064 1.019 12.50 12.13 0.020 0.022 2 Body-worn 802.11a Chain 0 15 Front 60 5300 0.011 1.019 12.50 12.13 Area Scan Pow er (dBm) 10-g SAR (W/kg) RF Exposure Dist. Freq. Duty Cycle Plot Mode Antenna Test Position Ch #. Max. SAR Tune-up Conditions (mm) (MHz) Factor Meas. Meas. Scaled No. (W/kg) Limit Rear 60 5300 0.293 1.019 12.50 12.13 Product Front 60 5300 0.511 1.019 12.50 12.13 0.061 0.068 3 802.11a Chain 0 0 Specific Edge 1 60 5300 0.115 1.019 12.50 12.13 Edge 4 60 5300 0.235 1.019 12.50 12.13 U-NII-2C Area Scan Pow er (dBm) 1-g SAR (W/kg) RF Exposure Dist. Freq. Duty Cycle Plot Mode Antenna Test Position Ch #. Max. SAR Tune-up Conditions (mm) (MHz) Factor Meas. Meas. Scaled No. (W/kg) Limit Left Touch 142 5710 0.347 1.117 10.40 9.63 Left Tilt 142 5710 0.228 1.117 10.40 9.63 Head 802.11n Chain 0 0 Right Touch 142 5710 0.510 1.117 10.40 9.63 0.161 0.215 4 Right Tilt 142 5710 0.437 1.117 10.40 9.63 Rear 142 5710 0.0196 1.117 10.40 9.63 Body-w orn 802.11n Chain 0 15 Front 142 5710 0.0379 1.117 10.40 9.63 0.014 0.019 5 Area Scan Pow er (dBm) 10-g SAR (W/kg) RF Exposure Dist. Freq. Duty Cycle Plot Mode Antenna Test Position Ch #. Max. SAR Tune-up Conditions (mm) (MHz) Factor Meas. Meas. Scaled No. (W/kg) Limit Rear 142 5710 0.3090 1.117 10.40 9.63 Product Front 142 5710 0.3650 1.117 10.40 9.63 0.045 0.060 6 802.11n Chain 0 0 Specific Edge 1 142 5710 0.3160 1.117 10.40 9.63 Edge 4 142 5710 0.1810 1.117 10.40 9.63 U-NII-3 Area Scan Power (dBm) 1-g SAR (W/kg) RF Exposure Dist. Duty Cycle Plot Mode Antenna Test Position Ch #. Freq. (MHz) Max. SAR Tune-up Conditions (mm) Factor Meas. Meas. Scaled No. (W/kg) Limit Left Touch 165 5825 0.164 1.019 11.50 10.47 Left Tilt 165 5825 0.133 1.019 11.50 10.47 Head 802.11a Chain 0 0 Right Touch 165 5825 0.546 1.019 11.50 10.47 0.208 0.269 7 Right Tilt 165 5825 0.134 1.019 11.50 10.47 Rear 165 5825 0.0221 1.019 11.50 10.47 0.005 0.007 8 Body-worn 802.11a Chain 0 15 Front 165 5825 0.0086 1.019 11.50 10.47 Area Scan Power (dBm) 10-g SAR (W/kg) RF Exposure Dist. Duty Cycle Plot Mode Antenna Test Position Ch #. Freq. (MHz) Max. SAR Tune-up Conditions (mm) Factor Meas. Meas. Scaled No. (W/kg) Limit Rear 165 5825 0.528 1.019 11.50 10.47 Product Front 165 5825 0.694 1.019 11.50 10.47 0.055 0.071 9 802.11a Chain 0 0 Specific Edge 1 165 5825 0.249 1.019 11.50 10.47 Edge 4 165 5825 0.352 1.019 11.50 10.47 Page 21 of 25 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 12247888-S1V2 Issue Date: 5/10/2018 11. SAR Measurement Variability In accordance with published RF Exposure KDB 865664 D01 SAR measurement 100 MHz to 6 GHz. These additional measurements are repeated after the completion of all measurements requiring the same head or body tissue-equivalent medium in a frequency band. The test device should be returned to ambient conditions (normal room temperature) with the battery fully charged before it is re-mounted on the device holder for the repeated measurement(s) to minimize any unexpected variations in the repeated results. 1) Repeated measurement is not required when the original highest measured SAR is <0.8 or 2 W/kg (1-g or 10-g respectively); steps 2) through 4) do not apply. 2) When the original highest measured SAR is ≥ 0.8 or 2 W/kg (1-g or 10-g respectively), repeat that measurement once. 3) Perform a second repeated measurement only if the ratio of largest to smallest SAR for the original and first repeated measurements is > 1.20 or when the original or repeated measurement is ≥ 1.45 or 3.6 W/kg (~ 10% from the 1-g or 10-g respective SAR limit). 4) Perform a third repeated measurement only if the original, first, or second repeated measurement is ≥ 1.5 or 3.75 W/kg (1-g or 10-g respectively) and the ratio of largest to smallest SAR for the original, first and second repeated measurements is > 1.20. Frequency Repeated Highest Band Air Interface RF Exposure Conditions Test Position SAR Measured (MHz) (Yes/No) SAR (W/kg) 5300 Wi-Fi 802.11a/n/ac Head Right Touch No 0.115 5500 Wi-Fi 802.11a/n/ac Head Right Touch No 0.161 5800 Wi-Fi 802.11a/n/ac Head Right Touch No 0.208 Note(s): Second Repeated Measurement is not required since the ratio of the largest to smallest SAR for the original and first repeated measurement is < 1.20. Frequency Repeated Highest Band Air Interface RF Exposure Conditions Test Position SAR Measured (MHz) (Yes/No) SAR (W/kg) 5300 Wi-Fi 802.11a/n/ac Product Specific Front No 0.061 5500 Wi-Fi 802.11a/n/ac Product Specific Front No 0.045 5800 Wi-Fi 802.11a/n/ac Product Specific Front No 0.055 Note(s): Repeated Measurement is not required since measured SAR is < 2 W/kg. Page 22 of 25 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 12247888-S1V2 Issue Date: 5/10/2018 12. Simultaneous Transmission SAR Analysis KDB 447498 D01 General RF Exposure Guidance explains how to calculate the SAR to Peak Location Ratio (SPLSR) between pairs of simultaneously transmitting antennas: SPLSR = (SAR1 + SAR2)1.5 /Ri Where: SAR1 is the highest reported or estimated SAR for the first of a pair of simultaneous transmitting antennas, in a specific test operating mode and exposure condition SAR2 is the highest reported or estimated SAR for the second of a pair of simultaneous transmitting antennas, in the same test operating mode and exposure condition as the first Ri is the separation distance between the pair of simultaneous transmitting antennas. When the SAR is measured, for both antennas in the pair, it is determined by the actual x, y and z coordinates in the 1-g SAR for each SAR peak location, based on the extrapolated and interpolated result in the zoom scan measurement, using the formula of [(x1- x2)2 + (y1-y2)2 + (z1-z2)2] In order for a pair of simultaneous transmitting antennas with the sum of 1-g SAR > 1.6 W/kg to qualify for exemption from Simultaneous Transmission SAR measurements, it has to satisfy the condition of: (SAR1 + SAR2)1.5 /Ri ≤ 0.04 Simultaneous Transmission Condition Page 23 of 25 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 12247888-S1V2 Issue Date: 5/10/2018 12.1. Sum of the SAR for WWAN & Wi-Fi & BT Standalone SAR (W/kg) ∑ 1-g SAR (W/kg) RF Exposure Test Position WWAN DTS U-NII BT WWAN + BT WWAN + DTS WWAN + DTS WWAN + DTS + U- NII WWAN + U-NII WWAN+U-NII+BT U-NII+BT conditions Chain 0 Chain 1 Chain 0 Chain 1 Chain 0 ① ①+⑥ ①+② ①+②+③ ① + ②+ ⑤ ①+④+⑤ ①+④+⑤+⑥ ④+⑤+⑥ ② ③ ④ ⑤ ⑥ Left Touch 0.170 0.383 0.120 0.269 0.135 0.083 0.253 0.553 0.673 0.688 0.574 0.657 0.487 Left Tilt 0.074 0.383 0.120 0.269 0.135 0.087 0.161 0.457 0.577 0.592 0.478 0.565 0.491 Head Right Touch 0.142 0.383 0.120 0.269 0.135 0.243 0.385 0.525 0.645 0.660 0.546 0.789 0.647 Right Tilt 0.062 0.383 0.120 0.269 0.135 0.223 0.285 0.445 0.565 0.580 0.466 0.689 0.627 Rear 0.259 0.033 0.011 0.022 0.021 0.210 0.469 0.292 0.303 0.313 0.302 0.512 0.253 Body-worn Front 0.350 0.033 0.011 0.022 0.021 0.210 0.560 0.383 0.394 0.404 0.393 0.603 0.253 Rear 0.378 0.048 0.031 0.315 0.693 0.426 0.457 Front 0.523 0.048 0.031 0.315 0.838 0.571 0.602 Hotspot Edge 2 0.148 0.048 0.031 0.315 0.463 0.196 0.227 Edge 3 0.570 0.048 0.031 0.315 0.885 0.618 0.649 Edge 4 0.342 0.048 0.031 0.315 0.657 0.390 0.421 Conclusion: Simultaneous transmission SAR measurement (Volume Scan) is not required because either the sum of the 1-g SAR is < 1.6 W/kg or the SPLSR is ≤ 0.04 for all circumstances that require SPLSR calculation. Page 24 of 25 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 12247888-S1V2 Issue Date: 5/10/2018 Appendixes Refer to separated files for the following appendixes. 12247888-S1V1 Appendix A: SAR Setup Photos 12247888-S1V1 Appendix B: SAR System Check Plots 12247888-S1V1 Appendix C: Highest SAR Test Plots 12247888-S1V1 Appendix D: SAR Liquid Tissue Ingredients 12247888-S1V1 Appendix E: SAR Probe Calibration Certificates 12247888-S1V1 Appendix F: SAR Dipole Calibration Certificates END OF REPORT Page 25 of 25 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.


Document Created: 2018-05-11 10:43:45
Document Modified: 2018-05-11 10:43:45
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC