TestRpt_HAC_T-Coil

FCC ID: PY7-57442Z

Test Report

Download: PDF
FCCID_3652034

        FCC HAC T-Coil Test Report                                          Report No. : HA760712-01B




     Hearing Aid Compatibility (HAC)
           T-Coil Test Report

             APPLICANT                 : Sony Mobile Communications Inc.
             BRAND NAME                : Sony
             FCC ID                    : PY7-57442Z
             STANDARD                  : FCC 47 CFR §20.19
                                         ANSI C63.19-2011

     We, SPORTON INTERNATIONAL INC., would like to declare that the tested sample has been
     evaluated in accordance with the procedures and shown the compliance with the
     applicable technical standards.


     The test results in this report apply exclusively to the tested model / sample. Without
     written approval of SPORTON INTERNATIONAL INC., the test report shall not be
     reproduced except in full.




         Reviewed by: Eric Huang / Manager




         Approved by: Jones Tsai / Manager



                             SPORTON INTERNATIONAL INC.
   No.52, Hwa Ya 1st Rd., Hwa Ya Technology Park, Kwei-Shan District, Taoyuan City, Taiwan
                                          (R.O.C.)




SPORTON INTERNATIONAL INC.                                         Page Number        : 1 of 24
TEL : 886-3-327-3456                                               Report Issued Date : Nov. 02, 2017
FAX : 886-3-328-4978                                               Report Version     : Rev. 01
FCC ID : PY7-57442Z


            FCC HAC T-Coil Test Report                                                                                                    Report No. : HA760712-01B

                                                               Table of Contents
1.   Attestation of Test Results ........................................................................................................................................ 4
2.   Administration Data ................................................................................................................................................... 4
3.   General Information ................................................................................................................................................... 5
     3.1    Description of Equipment Under Test (EUT) ..................................................................................................... 5
     3.2    Air Interface and Operating Mode..................................................................................................................... 6
     3.3    Applied Standards ............................................................................................................................................ 6
4.   HAC T-Coil .................................................................................................................................................................. 7
     4.1    T-Coil Coupling Field Intensity .......................................................................................................................... 7
     4.2    T-Coil Frequency Response ............................................................................................................................. 7
     4.3    T-Coil Signal Quality Categories ....................................................................................................................... 9
5.   Measurement System Specification ........................................................................................................................10
     5.1    System Configuration ......................................................................................................................................10
     5.2    Test Arch Phantom ..........................................................................................................................................10
     5.3    AMCC .............................................................................................................................................................. 11
     5.4    AM1D Probe .................................................................................................................................................... 11
     5.5    AMMI ...............................................................................................................................................................12
     5.6    System Hardware ............................................................................................................................................12
     5.7    Cabling of System for GSM / UMTS ................................................................................................................13
     5.8    Test Equipment List .........................................................................................................................................14
     5.9    Probe Calibration in AMCC ..............................................................................................................................15
     5.10 Reference Input of Audio Signal Spectrum ......................................................................................................16
     5.11 Establish Reference Level for GSM / UMTS ...................................................................................................17
6.   T-Coil Test Procedure ...............................................................................................................................................18
     6.1    Test Process and Flow Chart ...........................................................................................................................18
     6.2    Description of EUT Test Position .....................................................................................................................21
7.   HAC T-Coil Test Results ...........................................................................................................................................22
     7.1    Magnitude Result.............................................................................................................................................22
8.   Uncertainty Assessment ..........................................................................................................................................23
9.   References .................................................................................................................................................................24

Appendix A. Plots of T-Coil Measurement
Appendix B. DASY Calibration Certificate
Appendix C. Test Setup Photos




SPORTON INTERNATIONAL INC.                                                                                                  Page Number        : 2 of 24
TEL : 886-3-327-3456                                                                                                        Report Issued Date : Nov. 02, 2017
FAX : 886-3-328-4978                                                                                                        Report Version     : Rev. 01
FCC ID : PY7-57442Z


        FCC HAC T-Coil Test Report                                           Report No. : HA760712-01B

                                       Revision History
     REPORT NO.              VERSION                     DESCRIPTION                   ISSUED DATE

    HA760712-01B             Rev. 01      Initial issue of report                       Nov. 02, 2017




SPORTON INTERNATIONAL INC.                                          Page Number        : 3 of 24
TEL : 886-3-327-3456                                                Report Issued Date : Nov. 02, 2017
FAX : 886-3-328-4978                                                Report Version     : Rev. 01
FCC ID : PY7-57442Z


            FCC HAC T-Coil Test Report                                                   Report No. : HA760712-01B

1. Attestation of Test Results

Applicant Name             Sony Mobile Communications Inc.
Brand Name                 Sony
FCC ID                     PY7-57442Z
                           RQ3005WMD4
S/N
                           CQ300004NY
HW Version                 A
SW Version                 1.14
EUT Stage                  Production Unit
Exposure category          General Population/Uncontrolled Exposure
HAC Rating                 T4
Date Tested                2017/08/21 ~ 2017/10/09
Test Result                Pass


The device is compliance with HAC limits specified in guidelines FCC 47CFR §20.19 and ANSI Standard ANSI C63.19.




2. Administration Data
Sporton Lab is accredited to ISO 17025 by Taiwan Accreditation Foundation (TAF code: 1190) and the FCC designation
No. TW1190 under the FCC 2.948(e) by Mutual Recognition Agreement (MRA) in FCC test.

                                                Testing Laboratory
Test Site                   SPORTON INTERNATIONAL INC.
                            No.52, Hwa Ya 1st Rd., Hwa Ya Technology Park, Kwei-Shan District, Taoyuan City,
                            Taiwan (R.O.C.)
Test Site Location
                            TEL: +886-3-327-3456
                            FAX: +886-3-328-4978
                            Sporton Site No. :
Test Site No.
                            SAR04-HY
                                                  Applicant
Company Name               Sony Mobile Communications Inc.
Address                    4-12-3 Higashi-Shinagawa, Shinagawa-ku, Tokyo, 140-0002, Japan
                                                   Manufacturer
Company Name               Sony Mobile Communications Inc.
Address                    4-12-3 Higashi-Shinagawa, Shinagawa-ku, Tokyo, 140-0002, Japan




SPORTON INTERNATIONAL INC.                                                      Page Number        : 4 of 24
TEL : 886-3-327-3456                                                            Report Issued Date : Nov. 02, 2017
FAX : 886-3-328-4978                                                            Report Version     : Rev. 01
FCC ID : PY7-57442Z


            FCC HAC T-Coil Test Report                                                    Report No. : HA760712-01B

3. General Information
3.1 Description of Equipment Under Test (EUT)
         Wireless
                                        Frequency                                 Operating Mode
       Technologies
                                                              .GSM Voice
                            850                                                           Multi-Slot Class:
                                                              .GPRS (GMSK)
GSM                         1900                                                          Class 33
                                                              .EDGE (8PSK)
                            Does device support dual transfer mode?    (Yes)
                                                              .AMR / RMC 12.2Kbps
                            Band 2                            .HSDPA
W-CDMA (UMTS)               Band 4
                                                              .HSUPA
                            Band 5
                                                              .DC-HSDPA
                            Band 2
                            Band 4
                            Band 5                            .QPSK
                            Band 7                            .16QAM
LTE                         Band 12
                                                              .64QAM
                            Band 13
                                                              .Rel 11 Carrier Aggregation Downlink only
                            Band 17
                            Band 25
                            Band 66
                                                              .11b
                            2.4GHz:                           .11g
                            2412 MHz ~ 2462 MHz               .11n     (HT20)
                                                              .11ac   (VHT20)
                                                              .11a
WiFi                        5GHz:                             .11n     (HT20)
                            5.2GHz: 5180 MHz ~ 5240 MHz       .11n     (HT40)
                            5.3GHz: 5260 MHz ~ 5320 MHz
                                                              .11ac   (VHT20)
                            5.5GHz: 5500 MHz ~ 5720 MHz
                                                              .11ac   (VHT40)
                            5.8GHz: 5745 MHz ~ 5825 MHz
                                                              .11ac   (VHT80)
Bluetooth                   2.4GHz                            .BR / EDR / LE

NFC                         13.56MHz                          .ASK
Remark :
1. This product have two samples, the different between these samples are had memory / usb connector / fingerprint /
   battery / speaker / antenna switch, sample1 as the main tested, sample2 will spot-check worst case of GSM and
   WCDMA Band found in sample1.




SPORTON INTERNATIONAL INC.                                                       Page Number        : 5 of 24
TEL : 886-3-327-3456                                                             Report Issued Date : Nov. 02, 2017
FAX : 886-3-328-4978                                                             Report Version     : Rev. 01
FCC ID : PY7-57442Z


        FCC HAC T-Coil Test Report                                                Report No. : HA760712-01B
3.2 Air Interface and Operating Mode

    Air                                        C63.19            Simultaneous                      Power
 Interface        Band MHz          Type                                                 OTT
                                               Tested            Transmitter                      Reduction
                     850                                        WLAN, BT                 NA           No
                                    VO          Yes
   GSM              1900                                        WLAN, BT                 NA           No
                 GPRS/EDGE          DT           No             WLAN, BT                 Yes          No
                     850                                        WLAN, BT                 NA           No
                    1750            VO          Yes             WLAN, BT                 NA           No
 WCDMA
                    1900                                        WLAN, BT                 NA           No
                    HSPA            DT           No             WLAN, BT                 Yes          No
                   Band 2                                       WLAN, BT                              No
                   Band 4                                       WLAN, BT                              No
                   Band 5                                       WLAN, BT                              No
                   Band 7                                       WLAN, BT                              No
   LTE             Band 12          DT           No             WLAN, BT                 Yes          No
                   Band 13                                      WLAN, BT                              No
                   Band 17                                      WLAN, BT                              No
                   Band 25                                      WLAN, BT                              No
                   Band 66                                      WLAN, BT                              No
                    2450                                     GSM, WCDMA,LTE                           No
                    5200                                     GSM, WCDMA,LTE                           No
  WLAN              5300            DT           No          GSM, WCDMA,LTE              Yes          No
                    5500                                     GSM, WCDMA,LTE                           No
                    5800                                     GSM, WCDMA,LTE                           No
    BT              2450            DT           No          GSM, WCDMA,LTE               NA          No
VO=CMRS Voice Service
DT=Digital Transport



3.3 Applied Standards
    ‧        FCC CFR47 Part 20.19
    ‧        ANSI C63.19 2011-version
    ‧        FCC KDB 285076 D01 HAC Guidance v04r01
    ‧        FCC KDB 285076 D02 T Coil testing for CMRS IP v02




SPORTON INTERNATIONAL INC.                                               Page Number        : 6 of 24
TEL : 886-3-327-3456                                                     Report Issued Date : Nov. 02, 2017
FAX : 886-3-328-4978                                                     Report Version     : Rev. 01
FCC ID : PY7-57442Z


        FCC HAC T-Coil Test Report                                                   Report No. : HA760712-01B
4. HAC T-Coil
    FCC wireless hearing aid compatibility rules ensure that consumers with hearing loss are able to access
    wireless communications services through a wide selection of handsets without experiencing disabling
    radio frequency (RF) interference or other technical obstacles.
    To define and measure the hearing aid compatibility of handsets, in CFR47 part 20.19 ANSI C63.19 is
    referenced. A handset is considered hearing aid-compatible for acoustic coupling if it meets a rating of at
    least M3 under ANSI C63.19, and A handset is considered hearing aid compatible for inductive coupling
    if it meets a rating of at least T3.

    For inductive coupling, the wireless communication devices should be measured as below.
    1) Magnetic signal strength in the audio band
    2) Magnetic signal frequency response through the audio band
    3) Magnetic signal to noise


4.1 T-Coil Coupling Field Intensity
    When measured as specified in this standard, the T-Coil signal shall be ≥ –18 dB (A/m) at 1 kHz, in a 1/3
    octave band filter for all orientations.
4.2 T-Coil Frequency Response
    The frequency response of the perpendicular component of the magnetic field, measured in 1/3 octave
    bands, shall follow the response curve specified in this sub-clause, over the frequency range 300 Hz to
    3000 Hz.

    Figure 4.1 and Figure 4.2 provide the boundaries as a function of frequency. These response curves are
    for true field-strength measurements of the T-Coil signal. Thus, the 6 dB/octave probe response has
    been corrected from the raw readings.




    Fig. 4.1 Magnetic field frequency response for WDs with field strength≤-15dB at 1 KHz




SPORTON INTERNATIONAL INC.                                                  Page Number        : 7 of 24
TEL : 886-3-327-3456                                                        Report Issued Date : Nov. 02, 2017
FAX : 886-3-328-4978                                                        Report Version     : Rev. 01
FCC ID : PY7-57442Z


        FCC HAC T-Coil Test Report                                            Report No. : HA760712-01B




    Fig. 4.2 Magnetic field frequency response for WDs with a field that exceeds –15 dB(A/m) at 1 kHz




SPORTON INTERNATIONAL INC.                                           Page Number        : 8 of 24
TEL : 886-3-327-3456                                                 Report Issued Date : Nov. 02, 2017
FAX : 886-3-328-4978                                                 Report Version     : Rev. 01
FCC ID : PY7-57442Z


      FCC HAC T-Coil Test Report                                                    Report No. : HA760712-01B
4.3 T-Coil Signal Quality Categories
   This section provides the signal quality requirement for the intended T-Coil signal from a WD. Only the RF
   immunity of the hearing aid is measured in T-Coil mode. It is assumed that a hearing aid can have no
   immunity to an interference signal in the audio band, which is the intended reception band for this mode.
   A device is assessed beginning by determining the category of the RF environment in the area of the
   T-Coil source.

   The RF measurements made for the T-Coil evaluation are used to assign the category T1 through T4.
   The limitation is given in Table 4.3. This establishes the RF environment presented by the WD to a
   hearing aid.



                                                            Telephone parameters WD signal quality
                         Category
                                                              ((signal + noise) to noise ratio in dB)
                       Category T1                                           0 to 10 dB
                       Category T2                                          10 to 20 dB
                       Category T3                                          20 to 30 dB
                       Category T4                                        > 30 dB
                                Table 4.3 T-Coil Signal Quality Categories




SPORTON INTERNATIONAL INC.                                                 Page Number        : 9 of 24
TEL : 886-3-327-3456                                                       Report Issued Date : Nov. 02, 2017
FAX : 886-3-328-4978                                                       Report Version     : Rev. 01
FCC ID : PY7-57442Z


        FCC HAC T-Coil Test Report                                             Report No. : HA760712-01B
5. Measurement System Specification
5.1 System Configuration




                             Fig. 5.1 T-Coil setup with HAC Test Arch and AMCC
5.2 Test Arch Phantom
     Construction :   Enables easy and well defined positioning
                      of the phone and validation dipoles as well
                      as simple teaching of the robot.

     Dimensions :     370 x 370 x 370 mm




                                                                    Fig. 5.2 Photo of Arch Phantom




SPORTON INTERNATIONAL INC.                                            Page Number        : 10 of 24
TEL : 886-3-327-3456                                                  Report Issued Date : Nov. 02, 2017
FAX : 886-3-328-4978                                                  Report Version     : Rev. 01
FCC ID : PY7-57442Z


        FCC HAC T-Coil Test Report                                                   Report No. : HA760712-01B


5.3 AMCC

     The Audio Magnetic Calibration coil is a Helmholtz Coil designed for calibration of the AM1D probe. The
    two horizontal coils generate a homogeneous magnetic field in the z direction. The DC input resistance is
    adjusted by a series resistor to approximately 50Ohm, and a shunt resistor of 10 Ohm permits monitoring
    the current with a scale of 1:10.

                                                   Port description

    Signal                Connector               Resistance
    Coil In               BNC                     typically 50 Ohm
    Coil Monitor          BNO                     10Ohm ±1%(100mV corresponding to 1 A/m)

                                                     Specification

    Dimensions            370 x 370 x 196 mm, according to ANSI C63.19



5.4 AM1D Probe

     The AM1D probe is an active probe with a single sensor. It is fully RF-shielded and has a rounded tip
    6mm in diameter incorporating a pickup coil with its center offset 3mm from the tip and the sides. The
    symmetric signal preamplifier in the probe is fed via the shielded symmetric output cable from the AMMI
    with a 48V “phantom” voltage supply. The 7-pin connector on the back in the axis of the probe does not
    carry any signals. It is mounted to the DAE for the correct orientation of the sensor. If the probe axis is
    tilted 54.7 degree from the vertical, the sensor is approximately vertical when the signal connector is at
    the underside of the probe (cable hanging downwards).

                                                     Specification
    Frequency Range            0.1 ~ 20 kHz (RF sensitivity <-100dB, fully RF shielded )
    Sensitivity                <-50dB A/m @ 1 kHz
    Pre-amplifier              40 dB, symmetric
    Dimensions                 Tip diameter/ length: 6/ 290 mm, sensor according to ANSI-C63.19




SPORTON INTERNATIONAL INC.                                                  Page Number        : 11 of 24
TEL : 886-3-327-3456                                                        Report Issued Date : Nov. 02, 2017
FAX : 886-3-328-4978                                                        Report Version     : Rev. 01
FCC ID : PY7-57442Z


      FCC HAC T-Coil Test Report                                                      Report No. : HA760712-01B
5.5 AMMI




                                              Fig. 5.3 AMMI front panel

    The Audio Magnetic Measuring Instrument (AMMI) is a desktop 19-inch unit containing a sampling unit, a
    waveform generator for test and calibration signals, and a USB interface.

                                                    Specification
    Sampling rate                  48 kHz/24 bit
    Dynamic range                  85 dB
    Test signal generation         User selectable and predefined (vis PC)
    Calibration                    Auto-calibration/full system calibration using AMCC with monitor output
    Dimensions                     482 x 65 x 270 mm


5.6 System Hardware


                                                         DAE
     The data acquisition electronics (DAE) consists of a highly sensitive electrometer-grade preamplifier with
    auto-zeroing, a channel and gain-switching multiplexer, a fast 16 bit AD-converter and a command decoder
    and control logic unit.


                                                        Robot
     The SPEAG DASY system uses the high precision robots (DASY5: TX90XL) type from Stäubli SA
    (France). For the 6-axis controller system, the robot controller version (DASY5: CS8c) from Stäubli is used.




SPORTON INTERNATIONAL INC.                                                   Page Number        : 12 of 24
TEL : 886-3-327-3456                                                         Report Issued Date : Nov. 02, 2017
FAX : 886-3-328-4978                                                         Report Version     : Rev. 01
FCC ID : PY7-57442Z


       FCC HAC T-Coil Test Report                                                    Report No. : HA760712-01B
5.7 Cabling of System for GSM / UMTS
The principal cabling of the T-Coil setup is shown in Fig. 5.4 All cables provided with the basic setup have a
length of approximately 5 m.




                                          Fig. 5.4 T-Coil setup cabling




SPORTON INTERNATIONAL INC.                                                  Page Number        : 13 of 24
TEL : 886-3-327-3456                                                        Report Issued Date : Nov. 02, 2017
FAX : 886-3-328-4978                                                        Report Version     : Rev. 01
FCC ID : PY7-57442Z


       FCC HAC T-Coil Test Report                                                      Report No. : HA760712-01B
5.8 Test Equipment List
                                                                                               Calibration
Manufacturer           Name of Equipment               Type/Model   Serial Number
                                                                                       Last Cal.        Due Date
   SPEAG          Audio Magnetic 1D Field Probe          AM1DV3         3130         Nov. 16, 2016    Nov. 15, 2017
   SPEAG            Data Acquisition Electronics          DAE4          1399         Nov. 17, 2016    Nov. 16, 2017
   SPEAG            Data Acquisition Electronics          DAE4          778          May. 22, 2017    May. 21, 2018
   SPEAG          Audio Magnetic Calibration Coil         AMCC          1049             NCR                 NCR
   SPEAG           Audio Measuring Instrument             AMMI          1041             NCR                 NCR
  Gencom                   Thermometer                     TE1        TM685-1        Mar. 21, 2017    Mar. 20, 2018
   SPEAG                Test Arch Phantom                  N/A          N/A              NCR                 NCR
   SPEAG                 Phone Positoiner                  N/A          N/A              NCR                 NCR
    R&S                    Base Station                  CMU200        116457        May. 23, 2017    May. 22, 2018

                                            Table 5.1 Test Equipment List
Note:
1. NCR: “No-Calibration Required”




SPORTON INTERNATIONAL INC.                                                    Page Number        : 14 of 24
TEL : 886-3-327-3456                                                          Report Issued Date : Nov. 02, 2017
FAX : 886-3-328-4978                                                          Report Version     : Rev. 01
FCC ID : PY7-57442Z


       FCC HAC T-Coil Test Report                                                   Report No. : HA760712-01B
5.9 Probe Calibration in AMCC

     The probe sensitivity at 1 kHz is 0.06556 V/(A/m) (-23.66 dBV/(A/m)) was calibrated by AMCC coil for
    verification of setup performance.

     The evaluated probe sensitivity was able to be compared to the calibration of the AM1D probe. The
    frequency response and sensitivity was shown in Fig. 5.5. The probe signal is represented after application
    of an ideal integrator. The green curve represents the current though the AMCC, the blue curve the
    integrated probe signal. The DIFFERENCE between the two curves is equivalent to the frequency response
    of the probe system and shows the characteristics. The probe/system complies with the frequency
    response and linearity requirements in C63.19 according to the SPEAG’s calibrated report as shown in
    Annex B (AM1D probe: SPAM100AF) (1)The frequency response has been tested within +/- 0.5 dB of ideal
    differentiator from 100 Hz to 10 kHz. (2)The linearity has also been tested within 0.1dB from 5 dB below
    limitation to 16 dB above noise level. The AMCC coil is qualified according to certificate report,
    SDHACPO02A as shown in Annex B.




                            Fig. 5.5 The frequency response and sensitivity of AM1D probe




SPORTON INTERNATIONAL INC.                                                 Page Number        : 15 of 24
TEL : 886-3-327-3456                                                       Report Issued Date : Nov. 02, 2017
FAX : 886-3-328-4978                                                       Report Version     : Rev. 01
FCC ID : PY7-57442Z


        FCC HAC T-Coil Test Report                                                    Report No. : HA760712-01B

5.10 Reference Input of Audio Signal Spectrum
    With the reference job "use as reference" in the beginning of a procedure, measure the spectrum of the
    current when applied to the AMCC, i.e. the input magnetic field spectrum, as shown below Fig. 5.6 and
    Fig. 5.7. For this, the delay of the window shall be set to a multiple of the signal period and at least 2s.
    From the measurement on the device, using the same signal, the postprocessor deducts the input
    spectrum, so the result represents the net EUT response.




           Fig. 5.6 Audio signal spectrum of the broadband signal (48kHz_voice_300Hz~3 kHz)




              Fig. 5.7 Audio signal spectrum of the narrowband signal (48kHz_voice_1kHz)




SPORTON INTERNATIONAL INC.                                                   Page Number        : 16 of 24
TEL : 886-3-327-3456                                                         Report Issued Date : Nov. 02, 2017
FAX : 886-3-328-4978                                                         Report Version     : Rev. 01
FCC ID : PY7-57442Z


           FCC HAC T-Coil Test Report                                                              Report No. : HA760712-01B

5.11 Establish Reference Level for GSM / UMTS
According to ANSI C63.19:2011 section 7.4.2.1, the normal speech input level for HAC T-coil tests shall be
set to -16 dBm0 for GSM and UMTS (WCDMA), and to -18 dBm0 for CDMA. This technical note shows a
possibility to evaluate and set the correct level with the HAC T-Coil setup with a Rohde&Schwarz
communication tester CMU200 with audio option B52 and B85.
Establish a call from the CMU200 to a wireless device. Select CMU200 Network Bitstream ”Decoder Cal” to
have a 1 kHz signal with a level of 3.14 dBm0 at the speech output. Run the measurement job and read the
voltage level at the multi-meter display “Coil signal”. Read the RMS voltage corresponding to 3.14 dBm0 and
note it.
Determine the 1 kHz input level to generate the desired signal level of -16 dBm 0. Select CMU200 Network Bit
stream “Codec Cal” to loop the input via the codec to the output. Run the measurement job (AMMI 1 kHz
signal with gain 10 inserted) and read the voltage level at the multimeter display “Coil signal”. With Gain 10
setting, the measurement signal difference to the desired signal level of -16 dBm 0.
GSM/UMTS Calculations< 2017/8/21>
 3.14 dBm0 = -2.5 dBV  -16 dBm0 = -21.64 dBV
 Gain 10 = -19.86 dBV
 -21.64 - (-19.86) = -1.78 dB
 10* [10 ^ ((-1.78) / 20)] = 10 x 0.815 = 8.15
 Required Gain Factor = 10^(-RMS(dB)/20)
 Gain Setting = Required Gain Factor * 8.15

GSM/UMTS Calculations< 2017/10/9>
 3.14 dBm0 = -2.48 dBV  -16 dBm0 = -21.62 dBV
 Gain 10 = -19.87 dBV
 -21.62 - (-19.87) = -1.75 dB
 10* [10 ^ ((-1.75) / 20)] = 10 x 0.818 = 8.18
 Required Gain Factor = 10^(-RMS(dB)/20)
 Gain Setting = Required Gain Factor * 8.18
Note: Calculated Gain Setting = Resulting Gain * Required Gain Factor
The predefined signal types have the following differences / factors compared to the 1 kHz sine signal:
< 2017/8/21>
                                                             Peak to                      Required     Calculated     Adjusted
                                              Duration                       RMS            Gain                        Gain
               Signal Type                                    RMS                                        Gain
                                                (s)                          (dB)                (1)                          (2)
                                                              (dB)                        Factor        Setting       Setting
                    48k_voice_1kHz                1            16.2          -12.7          4.33          35.28        35.36
GSM/UMTS
               48k_voice_300Hz ~ 3kHz             2            21.6          -18.6          8.48          69.09         69.78

< 2017/10/9>
                                                             Peak to                      Required     Calculated     Adjusted
                                              Duration                       RMS
               Signal Type                                    RMS                           Gain         Gain           Gain
                                                (s)                          (dB)                (1)                          (2)
                                                              (dB)                        Factor        Setting       Setting
                    48k_voice_1kHz                1            16.2          -12.7          4.33          35.40        35.48
GSM/UMTS
               48k_voice_300Hz ~ 3kHz             2            21.6          -18.6          8.48          69.33         70.03

Remark:
(1) The gain for the specific signal shall typically be multiplied by this factor to achieve approx. the same level as for the
1kHz sine signal
(2) If the measurement for each signal type with calculated gain setting does not meet the desired level, the gain
setting will be manually adjusted until the desired level is obtained.


SPORTON INTERNATIONAL INC.                                                              Page Number        : 17 of 24
TEL : 886-3-327-3456                                                                    Report Issued Date : Nov. 02, 2017
FAX : 886-3-328-4978                                                                    Report Version     : Rev. 01
FCC ID : PY7-57442Z


        FCC HAC T-Coil Test Report                                                     Report No. : HA760712-01B

6. T-Coil Test Procedure
6.1 Test Process and Flow Chart
   Referenced to ANSI C63.19-2011, Section 7.4

   This section describes the procedures used to measure the ABM (T-Coil) performance of the WD. In
   addition to measuring the absolute signal levels, the A-weighted magnitude of the unintended signal shall
   also be determined. To assure that the required signal quality is measured, the measurement of the
   intended signal and the measurement of the unintended signal must be made at the same location for
   each measurement position. In addition, the RF field strength at each measurement location must be at or
   below that required for the assigned category.

   Measurements shall not include undesired properties from the WD's RF field; therefore, use of a coaxial
   connection to a base station simulator or non-radiating load, there might still be RF leakage from the WD,
   which can interfere with the desired measurement. Pre-measurement checks should be made to avoid
   this possibility. All measurements shall be performed with the WD operating on battery power with an
   appropriate normal speech audio signal input level given in ANSI C63.19-2011 Table 7.1. If the device
   display can be turned off during a phone call, then that may be done during the measurement as well,

   Measurement shall be performed at two locations specified in ANSI C63.19-2011 A.3, with the correct
   probe orientation for a particular location, in a multistage sequence by first measuring the field intensity of
   the desired T-Coil signal the same location as the desired ABM or T-Coil signal (ABM1), and the ratio of
   desired to undesired magnetic components (ABM2) must be measured at the same location as the
   desired ABM or T-Coil signal (ABM1), and the ratio of desired to undesired ABM signals must be
   calculated. For the perpendicular field location, only the ABM1 frequency response shall be determined in
   a third measurement stage.

   The following steps summarize the basic test flow for determining ABM1 and ABM2. These steps assume
   that a sine wave or narrowband 1/3 octave signal can be used for the measurement of ABM1.

   a)   A validation of the test setup and instrumentation may be performed using a TMFS or Helmholtz coil
        Measure the emissions and confirm that they are within the specified tolerance.

   b)   Position the WD in the test setup and connect the WD RF connector to a base station simulator or a
        non-radiating load. Confirm that equipment that requires calibration has been calibrated, and that
        the noise level meets the requirements given in ANSI C63.19-2011 clause 7.3.1.

   c)   The drive level to the WD ise set such that the reference input level specified in ANSI C63.19-2011
        Table 7.1 is input to the base station simulator (or manufacturer's test mode equivalent) in 1 kHz, 1/3
        octave band. This drive level shall be used for the T-Coil signal test (ABM1) at f = 1 kHz. Either a
        sine wave at 1025 Hz or a voice-like signal, band-limited to the 1 kHz 1/3 octave, as defined in ANSI
        C63.19-2011 clause 7.4.2, shall be used for the reference audio signal. If interference is found at
        1025 Hz an alternative nearby reference audio signal frequency may be used. The same drive level
        shall be used for the ABM1 frequency response measurements at each 1/3 octave band center
        frequency. The WD volume control may be set at any level up to maximum, provided that a signal at
        any frequency at maximum modulation would not result in clipping or signal overload.




SPORTON INTERNATIONAL INC.                                                    Page Number        : 18 of 24
TEL : 886-3-327-3456                                                          Report Issued Date : Nov. 02, 2017
FAX : 886-3-328-4978                                                          Report Version     : Rev. 01
FCC ID : PY7-57442Z


        FCC HAC T-Coil Test Report                                                      Report No. : HA760712-01B
   d)   Determine the magnetic measurement locations for the WD device (A.3), if not already specified by
        the manufacturer, as described in ANSI C63.19-2011 clause 7.4.4.1.1 and 7.4.4.2.

   e)   At each measurement location, measure and record the desired T-Coil magnetic signals (ABM1 at fi)
        as described in ANSI C63.19-2011 clause 7.4.4.2 in each individual ISO 266-1975 R10 standard 1/3
        octave band. The desired audio band input frequency (fi) shall be centered in each 1/3 octave band
        maintaining the same drive level as determined in item c) and the reading taken for that band.

        Equivalent methods of determining the frequency response may also be employed, such as fast
        Fourier transform (FFT) analysis using noise excitation or input-output comparison using simulated
        speech. The full-band integrated probe output, as specified in D.9, may be used, as long as the
        appropriate calibration curve is applied to the measured result, so as to yield an accurate
        measurement of the field magnitude. (The resulting measurement shall be an accurate
        measurement in dB A/m.)

        All Measurements of the desired signal shall be shown to be of the desired signal and not of an
        undesired signal. This may be shown by turning the desired signal ON and OFF with the probe
        measuring the same location. If the scanning method is used the scans shall show that all
        measurement points selected for the ABM1 measurement meet the ambient and test system noise
        criteria in ANSI C63.19-2011 clause 7.3.1.

   f)   At the measurement location for each orientation, measure and record the undesired broadband
        audio magnetic signal (ABM2) as specified in ANSI C63.19-2011 clause 7.4.4.4 with no audio signal
        applied (or digital zero applied, if appropriate) using A-weighting and the half-band integrator.
        Calculate the ratio of the desired to undesired signal strength (i,e., signal quality).

   g)   Obtain the data from the postprocessor, SEMCAD, and determine the category that properly
        classifies the signal quality based on ANSI C63.19-2011 Table 8.5.




SPORTON INTERNATIONAL INC.                                                     Page Number        : 19 of 24
TEL : 886-3-327-3456                                                           Report Issued Date : Nov. 02, 2017
FAX : 886-3-328-4978                                                           Report Version     : Rev. 01
FCC ID : PY7-57442Z


        FCC HAC T-Coil Test Report                                       Report No. : HA760712-01B



                                Confirm calibration of test equipment
                                Configure and validate the test setup
                                Establish WD reference level
                                Scan for measurement locations



                              Position and orient probe
                              Measure desired audio band signal
                               Strength
                              Measure undesired audio band signal
                               Strength




                              Calculate signal strength
                              Calculate signal quality
                              Measure frequency response




                                                                                           N
                                   Both y z locations measured?


                                                      Y

                                      Intensity and frequency                N
                                      response compliant ?


                                                     Y

                                   Determine and record signal
                                    quality category                                             Done



                                   Fig. 6.1 Test Flow Chart




SPORTON INTERNATIONAL INC.                                      Page Number        : 20 of 24
TEL : 886-3-327-3456                                            Report Issued Date : Nov. 02, 2017
FAX : 886-3-328-4978                                            Report Version     : Rev. 01
FCC ID : PY7-57442Z


       FCC HAC T-Coil Test Report                                                      Report No. : HA760712-01B
6.2 Description of EUT Test Position
   Fig.6.2 illustrate the references and reference plane that shall be used in a typical EUT emissions
   measurement. The principle of this section is applied to EUT with similar geometry. Please refer to
   Appendix C for the setup photographs.

         The area is 5 cm by 5 cm.
         The area is centered on the audio frequency output transducer of the EUT.
         The area is in a reference plane, which is defined as the planar area that contains the highest point
          in the area of the phone that normally rests against the user’s ear. It is parallel to the centerline of
          the receiver area of the phone and is defined by the points of the receiver-end of the EUT handset,
          which, in normal handset use, rest against the ear.
         The measurement plane is parallel to, and 10 mm in front of, the reference plane.




                     Fig 6.2 A typical EUT reference and plane for T-Coil measurements




SPORTON INTERNATIONAL INC.                                                    Page Number        : 21 of 24
TEL : 886-3-327-3456                                                          Report Issued Date : Nov. 02, 2017
FAX : 886-3-328-4978                                                          Report Version     : Rev. 01
FCC ID : PY7-57442Z


                 FCC HAC T-Coil Test Report                                                               Report No. : HA760712-01B
     7. HAC T-Coil Test Results
     7.1 Magnitude Result
                                                                               Telephone parameters WD signal quality
                                Category
                                                                                 ((signal + noise) to noise ratio in dB)
                               Category T1                                                         0 to 10 dB
                               Category T2                                                      10 to 20 dB
                               Category T3                                                      20 to 30 dB
                               Category T4                                                          > 30 dB

     The Table 7.1 shows testing result in position coordinates which are defined as deviation from earpiece center in
     millimeters. Signal strength measurement scans are presented in appendix A.



                                                                                            ABM1      ABM2
Plot                                                                          Probe                             SNR       T    Frequency
     Air Interface               Mode                  Channel Sample                        (dB       (dB
No.                                                                          Position                           (dB)    Rating Response
                                                                                            A/m)       A/m)
                                                                             Axial (Z)       8.90     -29.85    38.75    T4
 1     GSM850        Voice(speech codec/handset low)    189    Sample 1                                                         PASS
                                                                          Transversal (Y) -1.95       -46.44    44.49    T4
                                                                             Axial (Z)      9.75      -31.75    41.50    T4
 2     GSM850        Voice(speech codec/handset low)    189    Sample 2                                                         PASS
                                                                          Transversal (Y) -5.58       -46.33    40.75    T4
                                                                             Axial (Z)      8.92      -34.21    43.13    T4
 3    GSM1900        Voice(speech codec/handset low)    661    Sample 1                                                         PASS
                                                                          Transversal (Y) -0.15       -46.87    46.72    T4
                                                                             Axial (Z)      11.22     -45.68    56.90    T4
 4    WCDMA II          Voice(speech codec low)         9400   Sample 1                                                         PASS
                                                                          Transversal (Y) 10.51       -45.37    55.88    T4
                                                                             Axial (Z)      11.18     -45.12    56.30    T4
 5   WCDMA IV           Voice(speech codec low)         1413   Sample 1                                                         PASS
                                                                          Transversal (Y)   9.57      -46.00    55.57    T4
                                                                             Axial (Z)      11.40     -46.92    58.32    T4
 6   WCDMA IV           Voice(speech codec low)         1413   Sample 2                                                         PASS
                                                                          Transversal (Y)   8.32      -46.92    55.24    T4
                                                                             Axial (Z)      11.10     -45.92    57.02    T4
 7    WCDMA V           Voice(speech codec low)         4182   Sample 1                                                         PASS
                                                                          Transversal (Y) 11.49       -45.86    57.35    T4

         Remark:
            1.    There is no special HAC mode software on this EUT.
            2.    The detail frequency response results please refer to appendix A.
            3.    Test Engineer:Tom Jiang and Nick Yu




     SPORTON INTERNATIONAL INC.                                                               Page Number        : 22 of 24
     TEL : 886-3-327-3456                                                                     Report Issued Date : Nov. 02, 2017
     FAX : 886-3-328-4978                                                                     Report Version     : Rev. 01
     FCC ID : PY7-57442Z


          FCC HAC T-Coil Test Report                                                           Report No. : HA760712-01B
8. Uncertainty Assessment
The evaluation of uncertainly by the statistical analysis of a series of observations is termed a Type A
evaluation of uncertainty. The evaluation of uncertainty by means other than the statistical analysis of a series
of observation is termed a Type B evaluation of uncertainty. Each component of uncertainty, however
evaluated, is represented by an estimated standard deviation, termed standard uncertainty, which is
determined by the positive square root of the estimated variance. The combined standard uncertainty of the
measurement result represents the estimated standard deviation of the result. It is obtained by combining the
individual standard uncertainties of both Type A and Type B evaluation using the usual “root-sum-squares”
(RSS) methods of combining standard deviations by taking the positive square root of the estimated
variances. Expanded uncertainty is a measure of uncertainty that defines an interval about the measurement
result within which the measured value is confidently believed to lie. It is obtained by multiplying the combined
standard uncertainty by a coverage factor. For purpose of this document, a coverage factor two is used, which
corresponds to confidence interval of about 95 %. The DASY uncertainty Budget is showed in Table 8.2.

                                Uncertainty                                                      Standard       Standard
                                                Probability                   Ci        Ci
      Error Description           Value                           Divisor                       Uncertainty    Uncertainty
                                                Distribution                (ABM1)    (ABM2)
                                  (±%)                                                           (ABM1)         (ABM2)
                                                     Probe Sensitivity
      Reference Level              3.0            Normal              1       1          1        ± 3.0 %         ± 3.0 %
      AMCC Geometry                0.4          Rectangular           √3      1          1        ± 0.2 %         ± 0.2 %
      AMCC Current                 1.0          Rectangular           √3      1          1        ± 0.6 %         ± 0.6 %
  Probe Positioning During
                                   0.1          Rectangular           √3      1          1        ± 0.1 %         ± 0.1 %
         Calibrate
     Noise Contribution            0.7          Rectangular           √3    0.0143       1        ± 0.0 %         ± 0.4 %
      Frequency Slope              5.9          Rectangular           √3     0.1         1        ± 0.3 %         ± 3.5 %
                                                      Probe System
     Repeatability / Drift         1.0          Rectangular           √3      1          1        ± 0.6 %         ± 0.6 %
  Linearity / Dynamic Range        0.6          Rectangular           √3      1          1        ± 0.4 %         ± 0.4 %
       Acoustic Noise              1.0          Rectangular           √3     0.1         1        ± 0.1 %         ± 0.6 %
        Probe Angle                2.3          Rectangular           √3      1          1        ± 1.4 %         ± 1.4 %
     Spectral Processing           0.9          Rectangular           √3      1          1        ± 0.5 %         ± 0.5 %
      Integration Time             0.6            Normal              1       1          5        ± 0.6 %         ± 3.0 %
      Field Disturbation           0.2          Rectangular           √3      1          1        ± 0.1 %         ± 0.1 %
                                                        Test Signal
  Reference Signal Spectral
                                   0.6          Rectangular           √3      0          1        ± 0.0 %         ± 0.4 %
         Response
                                                        Positioning
      Probe Positioning            1.9          Rectangular           √3      1          1        ± 1.1 %         ± 1.1 %
     Phantom Thickness             0.9          Rectangular           √3      1          1        ± 0.5 %         ± 0.5 %
      EUT Positioning              1.9          Rectangular           √3      1          1        ± 1.1 %         ± 1.1 %
                                                  External Contributions
       RF Interference             0.0          Rectangular           √3      1         0.3       ± 0.0 %         ± 0.0 %
    Test Signal Variation          2.0          Rectangular           √3      1          1        ± 1.2 %         ± 1.2 %
                               Combined Standard Uncertainty                                      ± 4.1 %         ± 6.1 %
                                  Coverage Factor for 95 %                                                  K=2
                                    Expanded Uncertainty                                          ± 8.1 %         ± 12.3 %

                       Table 8.2 Uncertainty Budget of audio band magnetic measurement




SPORTON INTERNATIONAL INC.                                                           Page Number        : 23 of 24
TEL : 886-3-327-3456                                                                 Report Issued Date : Nov. 02, 2017
FAX : 886-3-328-4978                                                                 Report Version     : Rev. 01
FCC ID : PY7-57442Z


         FCC HAC T-Coil Test Report                                              Report No. : HA760712-01B

9. References
 [1]   ANSI C63.19-2011, “American National Standard for Methods of Measurement of Compatibility
       between Wireless Communications Devices and Hearing Aids”, 27 May 2011.
 [2]   FCC KDB 285076 D01v04r01, “Equipment Authorization Guidance for Hearing Aid Compatibility”, Apr
       2016
 [3]   FCC KDB 285076 D02v02, “Guidance for Performing T-Coil tests for Air Interfaces Supporting Voice
       over IP”, Apr 2016
 [4]   SPEAG DASY System Handbook




SPORTON INTERNATIONAL INC.                                             Page Number        : 24 of 24
TEL : 886-3-327-3456                                                   Report Issued Date : Nov. 02, 2017
FAX : 886-3-328-4978                                                   Report Version     : Rev. 01
FCC ID : PY7-57442Z



Document Created: 2017-11-15 19:49:19
Document Modified: 2017-11-15 19:49:19

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC