12073310-S3V2 FCC HAC_RF Report

FCC ID: PY7-21831A

Test Report

Download: PDF
FCCID_3721429

HAC RF EMISSIONS TEST REPORT FCC 47 CFR § 20.19 ANSI C63.19-2011 For GSM/WCDMA/LTE Phone with BT, DTS/UNII a/b/g/n/ac, GPS & NFC FCC ID: PY7-21831A Report Number: 12073310-S3V2 Issue Date: 1/17/2018 Prepared for SONY MOBILE COMMUNICATIONS INC. 4-12-3 HIGASHI-SHINAGAWA SHINAGAWA-KU,TOKYO, 140-0002, JAPAN Prepared by UL VERIFICATION SERVICES INC. 47173 BENICIA STREET FREMONT, CA 94538, U.S.A. TEL: (510) 771-1000 FAX: (510) 661-0888 NVLAP LAB CODE 200065-0

Report No.: 12073310-S3V2 Issue Date: 1/17/2018 Revision History Rev. Date Revisions Revised By V1 1/10/2018 Initial Issue -- Section 2: Updated KDB Version to latest Version V2 1/17/2018 Coltyce Sanders Section 4.1: Fixed Typo Page 2 of 17 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 12073310-S3V2 Issue Date: 1/17/2018 Table of Contents 1. Attestation of Test Results ............................................................................................................... 4 2. Test Methodology .............................................................................................................................. 5 3. Facilities and Accreditation .............................................................................................................. 5 4. Calibration and Uncertainty .............................................................................................................. 5 4.1. Measuring Instrument Calibration ..................................................................................................5 4.2. Measurement Uncertainty..............................................................................................................6 5. System Specifications ....................................................................................................................... 7 6. System Validation .............................................................................................................................. 8 6.1. System Validation Results .............................................................................................................8 7. Average Antenna Input Power & Evaluation for Low-power Exemption ...................................... 9 8. Device Under Test ........................................................................................................................... 10 8.1. Air Interfaces and Operating Mode ..............................................................................................10 9. Modulation Interference Factor (MIF)............................................................................................. 11 10. HAC RF Emissions Test Procedure ............................................................................................... 12 11. RF Emissions Measurement Criteria ............................................................................................. 15 12. HAC (RF Emissions) Test Results.................................................................................................. 15 12.1. Worst Case RF Emission Test Plot .............................................................................................16 Appendixes .............................................................................................................................................. 17 12073310-S3V1 Appendix A: HAC RF Emission Setup Photo ..............................................................17 12073310-S3V1 Appendix B: System Validation Plots ..........................................................................17 12073310-S3V1 Appendix C: HAC RF Emission Test Plots ..................................................................17 12073310-S3V1 Appendix D: MIF Attestation Letter..............................................................................17 12073310-S3V1 Appendix E: Probe Calibration Certificate ...................................................................17 12073310-S3V1 Appendix F: Dipole Calibration Certificates .................................................................17 12073310-S3V1 Appendix G: UID Specifications ..................................................................................17 Page 3 of 17 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 12073310-S3V2 Issue Date: 1/17/2018 1. Attestation of Test Results Applicant Name SONY MOBILE COMMUNICATIONS INC. FCC ID PY7-21831A FCC 47 CFR § 20.19 Applicable Standards ANSI C63.19-2011 HAC Rating M4 Date Tested 12/26/2017 Test Results Pass UL Verification Services Inc. tested the above equipment in accordance with the requirements set forth in the above standards. All indications of Pass/Fail in this report are opinions expressed by UL Verification Services Inc. based on interpretations and/or observations of test results. Measurement Uncertainties were not taken into account and are published for informational purposes only. The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. Note: The results documented in this report apply only to the tested sample, under the conditions and modes of operation as described herein. This document may not be altered or revised in any way unless done so by UL Verification Services Inc. and all revisions are duly noted in the revisions section. Any alteration of this document not carried out by UL Verification Services Inc. will constitute fraud and shall nullify the document. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, any agency of the Federal Government, or any agency of any government (NIST Handbook 150, Annex A). This report is written to support regulatory compliance of the applicable standards stated above. Approved & Released By: Prepared By: Dave Weaver Coltyce Sanders Operations Leader Test Engineer UL Verification Services Inc. UL Verification Services Inc. Page 4 of 17 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 12073310-S3V2 Issue Date: 1/17/2018 2. Test Methodology The tests documented in this report were performed in accordance with ANSI C63.19-2011 Methods of Measurement of Compatibility between Wireless Communications Devices and Hearing Aids, FCC published KDB 285076 D01 HAC Guidance v05 and TCB workshop updates. 3. Facilities and Accreditation The test sites and measurement facilities used to collect data are located at 47173 Benicia Street 47266 Benicia Street SAR Lab C SAR Lab 2 UL Verification Services Inc. is accredited by NVLAP, Laboratory Code 200065-0. 4. Calibration and Uncertainty 4.1. Measuring Instrument Calibration The measuring equipment utilized to perform the tests documented in this report has been calibrated in accordance with the manufacturer's recommendations, and is traceable to recognized national standards. Name of Equipment Manufacturer Type/Model Serial No. Cal. Due Date Synthesized Signal Generator Agilent N5181A MY50140610 5/31/2018 Power Meter Agilent N1912A MY55196008 5/12/2018 Power Sensor Agilent N1921A MY52260009 1/5/2018 Power Sensor Agilent N1921A MY53020038 4/13/2018 Amplifier MITEQ AMF-4D-00400600-50-30P 1795093 N/A Directional coupler Werlatone C8060-102 2140 N/A DC Power Supply HP 6296A 2841A-05955 N/A Data Acquisition Electronics SPEAG DAE4 1343 8/21/2018 E-Field Probe* SPEAG EF3DV3 4041 3/14/2018 Calibration Dipole SPEAG CD835V3 1175 5/10/2018 Calibration Dipole SPEAG CD1880V3 1159 5/10/2018 Calibration Dipole SPEAG CD2600V3 1008 7/21/2018 Radio Communication Tester R &S CMW 500 125326 3/6/2018 Note(s): *: According to SPEAG’s Technical Report, “MIF Verification”, Doc # TR-FB-12.09.04-1, issued date: 9/4/2012. E-field probes are calibrated with specified uncertainty according to ISO 17025 as described in their calibration certificate. The MIF according to the definition in ANSI C63.19 is specific for a modulation and can therefore be used as a constant value if the probe has been PMR calibrated. Page 5 of 17 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 12073310-S3V2 Issue Date: 1/17/2018 4.2. Measurement Uncertainty HAC Uncertainty Budget According to ANSI C63.19 Uncertainty Std. Unc.(±%) Error Description Probe Dist. Div. (Ci) E (Ci) H value (±%) E H Measurement System Probe Calibration 5.1 N 1 1 1 5.1 5.10 Axial Isotropy 4.7 R 1.732 1 1 2.7 2.71 Sensor Displacement 16.5 R 1.732 1 0.145 9.5 1.38 Boundary Effects 2.4 R 1.732 1 1 1.4 1.39 Phantom Boundary Effects 7.2 R 1.732 1 0 4.1 0.00 Linearity 4.7 R 1.732 1 1 2.7 2.71 Scaling to PMR Calibration 10.0 R 1.732 1 1 5.8 5.77 System Detection Limit 1.0 R 1.732 1 1 0.6 0.58 Readout Electronics 0.3 N 1 1 1 0.3 0.30 Response Time 0.8 R 1.732 1 1 0.5 0.46 Integration Time 2.6 R 1.732 1 1 1.5 1.50 RF Ambient Conditions 3.0 R 1.732 1 1 1.7 1.73 RF Reflections 12.0 R 1.732 1 1 6.9 6.93 Probe Positioner 1.2 R 1.732 1 0.67 0.7 0.46 Probe Positioning 4.7 R 1.732 1 0.67 2.7 1.82 Extrapolation and Interpolation 1.0 R 1.732 1 1 0.6 0.58 Test sample Related Test Positioning Vertical 4.7 R 1.732 1 0.67 2.7 1.82 Test Positioning Lateral 1.0 R 1.732 1 1 0.6 0.58 Device Holder and Phantom 2.4 R 1.732 1 1 1.4 1.39 Power Drift 5.0 R 1.732 1 1 2.9 2.89 Phantom and Setup Related Phantom Thickness 2.4 R 1.732 1 0.67 1.4 0.93 Combined Std. Uncertainty 16.3 12.3 Expanded Std. Uncertainty on Power 32.6 24.6 Expanded Std. Uncertainty on Field 16.3 12.3 Notesfor table 1. N - Nomal 2. R - Rectangular 3. Div. - Divisor used to obtain standard uncertainty 4. Ci - is te sensitivity coefficient Page 6 of 17 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 12073310-S3V2 Issue Date: 1/17/2018 5. System Specifications E-field measurements are performed using the DASY5 automated dosimetric assessment system. The DASY5 is made by Schmid & Partner Engineering AG (SPEAG) in Zurich, Switzerland. The DASY5 HAC Extension consists of the following parts: Test Arch Phantom The specially designed Test Arch allows high precision positioning of both the device and any of the validation dipoles. ER3DV6 Isotropic E-Field Probe Construction: One dipole parallel, two dipoles normal to probe axis Built-in shielding against static charges PEEK enclosure material (resistant to organic solvents, e.g., glycolether) Calibration: In air from 100 MHz to 3.0 GHz (absolute accuracy ±6.0%, k=2) Frequency: 100 MHz to > 6 GHz; Linearity: ± 0.2 dB (100 MHz to 3 GHz) Directivity: ± 0.2 dB in air (rotation around probe axis) ± 0.4 dB in air (rotation normal to probe axis) Dynamic Range: 2 V/m to > 1000 V/m; Linearity: ± 0.2 dB Dimensions: Overall length: 330 mm (Tip: 16 mm) Tip diameter: 8 mm (Body: 12 mm) Distance from probe tip to dipole centers: 2.5 mm The closest part of the sensor element is 1.1 mm closer to the tip Application: General near-field measurements up to 6 GHz Field component measurements Page 7 of 17 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 12073310-S3V2 Issue Date: 1/17/2018 6. System Validation The test setup was validated when first configured and verified periodically thereafter to ensure proper function. The procedure provided in this section is a validation procedure using dipole antennas for which the field levels were computed by numeric modeling. Procedure: Place a dipole antenna meeting the requirements given in ANSI C63.19-2011 in the normally occupied by the WD. The dipole antenna serves as a known source for an electrical and magnetic output. Position the E-field probe so that the following occurs: ‧ The probes and their cables are parallel to the coaxial feed of the dipole antenna ‧ The probe cables and the coaxial feed of the dipole antenna approach the measurement area from opposite directions ‧ The center point of the probe element(s) is 15 mm from the closest surface of the dipole elements. Scan the length of the dipole with the E-field probe and record the two maximum values found near the dipole ends. Average the two readings and compare the reading to the expected value in the calibration certificate or the expected value in this standard. Setup diagram 6.1. System Validation Results Max. measured from Average Deviation Target (V/m) Plot SAR Date Dipole Type_Serial #_Freq. Dipole Cal. max. above (note 1) above high end above low end (From SPEAG) No. Lab Due Data (V/m) (V/m) arm (V/m) ±% C 12/26/2017 CD835V3_SN:1175_(835 MHz) 5/10/2018 116.00 125.10 120.55 109.20 10.39 1 C 12/26/2017 CD1880V3_SN:1159_(1880 MHz) 5/10/2018 87.97 96.03 92.00 88.00 4.55 2 C 12/26/2017 CD2600V3_SN:1008_(2600 MHz) 7/21/2018 91.51 93.17 92.34 86.20 7.12 3 Notes: 1) Delta (Deviation) % = 100 * (Measured value minus Target value) divided by the Target value. Deltas within ±25% are acceptable, of which 12% is deviation and 13% is measurement uncertainty. 2) The maximum E-field or were evaluated and compared to the target values provided by SPEAG in the calibration certificate of specific dipoles. 3) Please refer to the appendix for detailed measurement data and plots. Page 8 of 17 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 12073310-S3V2 Issue Date: 1/17/2018 7. Average Antenna Input Power & Evaluation for Low-power Exemption An RF air interface technology of a device is exempt from testing when its average antenna input power plus its MIF is ≤17 dBm for any of its operating modes. If a device supports multiple RF air interfaces, each RF air interface shall be evaluated individually. Average Antenna Worst Case MIF Input Power Air-Interface HAC Tested Input Power (dBm)1 (dB) plus its MIF (dBm) GSM850 33.2 3.63 36.83 Yes GSM1900 28.7 3.63 32.33 Yes W-CDMA Band II 22.7 -27.23 -4.53 No W-CDMA Band IV 22.7 -27.23 -4.53 No W-CDMA Band V 24.9 -27.23 -2.33 No LTE Band 2 23.0 -9.76 13.24 No LTE Band 4 23.0 -9.76 13.24 No LTE Band 5 25.0 -9.76 15.24 No LTE Band 7 23.0 -9.76 13.24 No LTE Band 12 25.0 -9.76 15.24 No LTE Band 13 25.0 -9.76 15.24 No LTE Band 17 25.0 -9.76 15.24 No LTE Band 26 24.0 -9.76 14.24 No LTE Band 41 23.0 -1.44 21.56 Yes LTE Band 66 23.0 -9.76 13.24 No 802.11b Chain 0 13.5 -2.02 11.48 No 802.11g Chain 0 13.8 0.12 13.92 No 802.11b Chain 1 13.3 -2.02 11.28 No 802.11g Chain 1 13.3 0.12 13.42 No 802.11a Chain 0 12.5 -3.15 9.35 No 802.11a Chain 1 12.7 -3.15 9.55 No Note(s): 1. Max tune-up limit Page 9 of 17 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 12073310-S3V2 Issue Date: 1/17/2018 8. Device Under Test Normal operation Held to head Back Cover ☒ The Back Cover is not removable. S/N IMEI Notes QV7000FN12 004402458317488 GSM LB Test sample information QV70006W12 004402458317918 GSM MB QV7000FP12 004402458317553 LTE HB 8.1. Air Interfaces and Operating Mode Air Bands C63.19 Power Type Simultaneous Transmitter OTT Interface (MHz) Tested Reduction 850 VO Yes Wi-Fi and BT NA NA GSM 1900 GPRS/EDGE DT No Wi-Fi and BT Yes NA 850 1700 VO No1 Wi-Fi and BT NA NA W-CDMA 1900 HSPA DT No Wi-Fi and BT Yes NA 700 850 1700 LTE - FDD VD No1 Wi-Fi and BT Yes NA 1900 2300 2500 LTE - TDD 2600 VD Yes Wi-Fi and BT Yes NA 2450 5200 Wi-Fi 5300 VD No1 WWAN and BT Yes NA 5500 5800 BT 2450 DT NA WWAN and Wi-Fi NA NA Type Note: VO=CMRS Voice Service 1. Evaluated for MIF and low power exemption. DT – Digital Transport VD=CMRS IP Voice Service and Digital Transport Page 10 of 17 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 12073310-S3V2 Issue Date: 1/17/2018 9. Modulation Interference Factor (MIF) The HAC Standard ANSI C63.19-2011 defines a new scaling using the Modulation Interference Factor (MIF) which replaces the need for the Articulation Weighting Factor (AWF) during the evaluation and is applicable to any modulation scheme. The Modulation Interference factor (MIF, in dB) is added to the measured average E-field (in dBV/m) and converts it to the RF Audio Interference level (in dBV/m). This level considers the audible amplitude modulation components in the RF E-field. CW fields without amplitude modulation are assumed to not interfere with the hearing aid electronics. Modulations without time slots and low fluctuations at low frequencies have low MIF values, TDMA modulations with narrow transmission and repetition rates of few 100 Hz have high MIF values and give similar classifications as ANSI C63-2007. Definitions ER3D, E-field probes have a bandwidth <10 kHz and can therefore not evaluate the RF envelope in the full audio band. DASY52 is therefore using the “indirect” measurement method according to ANSI C63.19-2011 which is the primary method. These near field probes read the averaged E-field measurement. Especially for the new high peak-to-average (PAR) signal types, the probes shall be linearized by probe modulation response (PMR) calibration in order to not overestimate the field reading. The evaluation method or the MIF is defined in ANSI C63.19-2011 section D.7. An RMS demodulated RF signal is fed to a spectral filter (similar to an A weighting filter) and forwarded to a temporal filter acting as a quasi-peak detector. The averaged output of these filtering is called to a 1 kHz 80% AM signal as reference. MIF measurement requires additional instrumentation and is not well suited for evaluation by the end user with reasonable uncertainty It may alternatively be determined through analysis and simulation, because it is constraint and characteristic for a communication signal. DASY52 uses well defined signals for PMR calibration. The MIF of these signals has been determined by simulation and is automatically applied. MIF values were not tested by a probe or as specified in the standards but are based on analysis provided by SPEAG for all the air interfaces (GSM, WCDMA, CDMA, LTE). The data included in this report are for the worst case operating modes. The UIDs used are listed below: UID Communication System Name MIF (dB) 10021-DAB GSM-FDD (TDMA, GMSK) 3.63 10011-CAB UMTS-FDD (WCDMA) -27.23 10170-CAB LTE-FDD (SC-FDMA, 1 RB, 20 MHz, 16QAM) -9.76 10182-CAB LTE-FDD (SC-FDMA, 1 RB, 15 MHz, 16QAM) -9.76 10176-CAB LTE-FDD (SC-FDMA, 1 RB, 10 MHz, 16QAM) -9.76 10173-CAB LTE-TDD (SC-FDMA, 1 RB, 20 MHz, 16QAM) -1.44 10061-CAA IEEE 802.11b WiFi 2.4 GHz (DSSS, 11 Mbps) -2.02 10077-CAA IEEE 802.11g WiFi 2.4 GHz (DSSS/OFDM, 54 Mbps) 0.12 10069-CAA IEEE 802.11a/n WiFi 5 GHz (OFDM, 54 Mbps) -3.15 A PMR calibrated probe is linearized for the selected waveform over the full dynamic range within the uncertainty specified in its calibration certificate. ER3D, EF3D and EU2D E-field probes have a bandwidth <10 kHz and can therefore not evaluate the RF envelope in the full audio band. DASY52 is therefore using the \indirect" measurement method according to ANSI C63.19-2011 which is the primary method. These near field probes read the averaged E-field measurement. Especially for the new high peak-to-average (PAR) signal types, the probes shall be linearized by PMR calibration in order to not overestimate the field reading. The MIF measurement uncertainty is estimated as follows, for modulation frequencies from slotted waveforms with fundamental frequency and at least 2 harmonics within 10 kHz: • 0.2 dB for MIF -7 to +5 dB, • 0.5 dB for MIF -13 to +11 dB • 1 dB for MIF > -20 dB Page 11 of 17 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 12073310-S3V2 Issue Date: 1/17/2018 10. HAC RF Emissions Test Procedure The following are step-by-step test procedures. a) Confirm proper operation of the field probe, probe measurement system and other instrumentation and the positioning system. b) Position the WD in its intended test position. c) Set the WD to transmit a fixed and repeatable combination of signal power and modulation characteristic that is representative of the worst case (highest interference potential) encountered in normal use. Transiently occurring start-up, changeover, or termination conditions, or other operations likely to occur less than 1% of the time during normal operation, may be excluded from consideration. d) The center sub-grid shall be centered on the T-Coil mode perpendicular measurement point or the acoustic output, as appropriate. Locate the field probe at the initial test position in the 50 mm by 50 mm grid, which is contained in the measurement plane, refer to illustrated in Figure 1. If the field alignment method is used, align the probe for maximum field reception. e) Record the reading at the output of the measurement system f) Scan the entire 50 mm by 50 mm region in equally spaced increments and record the reading at each measurement point. The distance between measurement points shall be sufficient to assure the identification of the maximum reading. g) Identify the five contiguous sub-grids around the center sub-grid whose maximum reading is the lowest of all available choices. This eliminates the three sub-grids with the maximum readings. Thus, the six areas to be used to determine the WD’s highest emissions are identified. h) Identify the maximum reading within the non-excluded sub-grids identified in step g). i) Convert the highest field reading within identified in step h) to RF audio interference level, in V/m, by taking the square root of the reading and then dividing it by the measurement system transfer function, established in 5.5.1.1 Convert this result to dB(V/m) by taking the base-10 logarithm and multiplying by 20. Indirect measurement method Replacing step i), the RF audio interference level in dB (V/m) is obtained by adding the MIF (in dB) to the maximum steady-state rms field-strength reading, in dB (V/m), from step h). Use this result to determine the category rating j) Compare this RF audio interference level with the categories in Clause 8 (ANSI C63.19-2011) and record the resulting WD category rating k) For the T-Coil mode M-rating assessment, determine whether the chosen perpendicular measurement point is contained in an included sub-grid of the first scan. If so, then a second scan is not necessary. The first scan and resultant category rating may be used for the T-Coil mode M rating. Otherwise, repeat step a) through step i), with the grid shifted so that it is centered on the perpendicular measurement point. Record the WD category rating. Page 12 of 17 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 12073310-S3V2 Issue Date: 1/17/2018 Figure 1 - WD reference and plane for RF emission measurements Page 13 of 17 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 12073310-S3V2 Issue Date: 1/17/2018 Test flowchart Per ANSI-PC63.19 2011 Test Instructions • Confirm proper operation of probes and instrumentation • Position WD • Configure WD Tx Operation (Step a-c) • Initialize field probe and take first reading • Scan Area (Step d-f) • Identify exclusion area • Rescan or reanalyze open area todetermine maximum • Indirect method: Add the MIF to the maximum steady state rms field strength and record RF Audio Interference Level, in dB (V/m) (Step g-i) Identify & Record Category (Step j) Page 14 of 17 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 12073310-S3V2 Issue Date: 1/17/2018 11. RF Emissions Measurement Criteria WD RF audio interference level caterories in logarithmic units E-field emissions Emission Categories < 960 MHz > 960 MHz Category M1 50 to 55 dB (V/m) 40 to 45 dB (V/m) Category M2 45 to 50 dB (V/m) 35 to 40 dB (V/m) Category M3 40 to 45 dB (V/m) 30 to 35 dB (V/m) Category M4 <40 dB (V/m) <30 dB (V/m) 12. HAC (RF Emissions) Test Results MIF values were not tested by a probe or as specified in the standards but are based on analysis provided by SPEAG for the following User Identifiers and air interfaces. The data included in this report are for the worst case operating modes. Refer to Appendix D and G for the MIF vales that represent the worst case operation modes. Results Results* Margin Plot Air-Interface Ch. No. Freq. (MHz) plus 0.2dB uncertaninty M-Rating (dB V/m) (dB) No. (dB V/m) 128 824.40 31.13 31.33 8.67 M4 1 GSM850 190 836.60 31.89 32.09 7.91 M4 2 251 848.60 31.40 31.60 8.40 M4 3 512 1850.20 26.15 26.35 3.65 M4 4 GSM1900 661 1880.00 25.85 26.05 3.95 M4 5 810 1909.80 26.04 26.24 3.76 M4 6 39750 2506.00 14.27 14.47 15.53 M4 7 40185 2549.50 14.94 15.14 14.86 M4 8 LTE-TDD 40620 2593.00 12.50 12.70 17.30 M4 9 Band 41 41055 2636.50 14.30 14.50 15.50 M4 10 41490 2680.00 16.04 16.24 13.76 M4 11 W-CDMA & Refer to Section 7 Evaluation for Low-power Exemption. RF Emission testing for this device is required LTE-FDD & only for GSM voice modes and LTE-TDD. All other applicable air-interfaces are exempt from testing in M4 N/A Wi-Fi accordance with C63.19-2011 Clause 4.4 and are rated M4. Note(s): *: Measured Audio Interference level in dB (V/m): indirect method (max rms field strength Plus MIF) Page 15 of 17 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 12073310-S3V2 Issue Date: 1/17/2018 12.1. Worst Case RF Emission Test Plot Test Laboratory: UL Verification Services Inc. SAR Lab C Date: 12/26/2017 HAC-RF Emission Communication System: UID 10021 - DAC, GSM-FDD (TDMA, GMSK); Frequency: 1850.2 MHz; Duty Cycle: 1:8.6896 Phantom section: RF Section DASY5 Configuration: - Probe: EF3DV3 - SN4041; ConvF(1, 1, 1); Calibrated: 3/14/2017; - Sensor-Surface: (Fix Surface) - Electronics: DAE4 Sn1343; Calibrated: 8/21/2017 - Phantom: HAC Test Arch with AMCC; Type: SD HAC P01 BB - Measurement SW: DASY52, Version 52.10 (0);SEMCAD X Version 14.6.10 (7417) GSM1900 E-Field measurement/Voice_ch 512/Hearing Aid Compatibility Test (101x101x1): Interpolated grid: dx=0.5000 mm, dy=0.5000 mm Device Reference Point: 0, 0, -6.3 mm Reference Value = 8.504 V/m; Power Drift = -0.13 dB Applied MIF = 3.63 dB RF audio interference level = 26.15 dBV/m Emission category: M4 MIF scaled E-field Grid 1 M4 Grid 2 M4 Grid 3 M4 26.91 dBV/m 27.42 dBV/m 26.96 dBV/m Grid 4 M4 Grid 5 M4 Grid 6 M4 22.39 dBV/m 22.6 dBV/m 22.37 dBV/m Grid 7 M4 Grid 8 M4 Grid 9 M4 22.93 dBV/m 26.15 dBV/m 26.15 dBV/m 0 dB = 23.49 V/m = 27.42 dBV/m Page 16 of 17 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 12073310-S3V2 Issue Date: 1/17/2018 Appendixes Refer to separated files for the following appendixes 12073310-S3V1 Appendix A: HAC RF Emission Setup Photo 12073310-S3V1 Appendix B: System Validation Plots 12073310-S3V1 Appendix C: HAC RF Emission Test Plots 12073310-S3V1 Appendix D: MIF Attestation Letter 12073310-S3V1 Appendix E: Probe Calibration Certificate 12073310-S3V1 Appendix F: Dipole Calibration Certificates 12073310-S3V1 Appendix G: UID Specifications END OF REPORT Page 17 of 17 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.


Document Created: 2018-01-17 11:55:23
Document Modified: 2018-01-17 11:55:23
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC