Users Manual.pdf

FCC ID: PY317300399

Users Manual

Download: PDF
FCCID_3811130

Quick Start Guide 1

What’s Included Welcome Base station (VMB3500) Arlo Wire-Free camera Lithium CR 123 batteries* Thank you for choosing Arlo. Getting started is easy. Base station Ethernet cable Wall mount* Mounting screws power adapter and anchors* * Quantity varies with number of cameras 2 3

1 Get the App 2 Connect Your Base Station to the Internet For the best experience, download the Arlo app for your smartphone by scanning this QR code or a. Connect the base station to your router using the Ethernet cable that is included. searching for Arlo in the app store. Reset SYNC Ethernet DC arlo.netgear.com 4 5

3 Get an Account b. Connect the AC adapter to your base station and plug it in. ¾¾ To create a new Arlo account: The Power LED and Internet LED on the back of the base station light green in about two minutes. a. Launch the Arlo app from your smartphone, tap the New to Arlo? button, and select Arlo Wire-Free. If you are using a computer, visit arlo.netgear.com. SYNC Ethernet DC b. Follow the onscreen instructions. Reset SYNC Ethernet DC ¾¾ To add an Arlo camera to an existing Arlo account: et Res DC C SYN et ern Eth a. If you already set up an Arlo account, log in, and click or tap Add Device. (If this doesn’t happen, visit b. Follow the onscreen instructions. arlo.com/support/ for troubleshooting tips.) 6 7

4 Insert Batteries Into Your Cameras 5 Sync Your Cameras With the Base Station a. Unlock the battery c. Insert two batteries d. Insert two batteries e. Close the Note: Cameras must be synced one at a time. compartment by near the back of the near the battery door. sliding and holding the camera. compartment hinge. a. Bring the camera within 1 to 3 feet (30 to 100 centimeters) of the base station. latch. b. Slide the battery door back and lift it to open the compartment. t Rese DC SYNC et ern Eth 8 9

b. Press the Sync button on the back of d. Press the Sync button on top of the A blue LED on the camera blinks slowly Syncing more than one camera? the base station for about two seconds. camera for about two seconds. Release when the sync process starts. The blue Go to page 9 and repeat steps 5a Release the button. the button. LED blinks rapidly to confirm sync. through 5d for each camera. c. Wait for the Sync Status LED to blink The camera is ready for viewing. green. Note: If the LED blinks amber quickly, the sync is not successful. You must repeat the sync process. et Res DC C SYN et ern Eth et Res C t SYN rne e Eth 10 11

6 Place or Mount Your Cameras Locate a spot for your camera To mount your camera to the wall: You can place your camera on a shelf or Fasten the mounting screw into the wall, other flat surface, or you can mount it to and hang the magnetic mount from the wall. the screw. Tip: Use the Arlo app in Position mode If you’re mounting the camera to drywall, (found in Camera Settings) to help aim the camera. be sure to use the plastic drywall anchors that are provided. Tip: You can also use double-sided tape instead of screws. 12 13

You’re Done! Base Station LED Guide Power Internet Camera Congratulations! Your Arlo System is set up and ready to go. Green Green Green The base station The base station Cameras are is powered on. is connected to connected to the To view useful tutorial videos, find troubleshooting tips, or the Internet. base station. get support, visit arlo.com/support/. Blinking green Blinking green Blinking green A firmware update The base station is The base station is Res et is in progress. DO sending data over attempting to sync NOT TURN OFF the Internet. with a camera. DC C SYN et ern Eth BASE STATION OR CAMERAS. Amber Amber Blinking amber The base station The base station is A camera is too is booting. connected to the far from the base router but did not station. Signal establish an Internet strength is weak. connection. Off Off Amber The base station The base station is The base station is is powered off. not connected to not assigned to an your router. Arlo account. Off No cameras are detected. 14 15

©NETGEAR, Inc., NETGEAR, the NETGEAR Logo, and Arlo are trademarks of NETGEAR, Inc. Compliance For the current EU Declaration of Conformity, visit http://kb.netgear.com/app/answers/detail/a_id/11621/. For regulatory compliance information, visit http://www.netgear.com/about/regulatory/. 350 East Plumeria Drive NETGEAR INTL LTD San Jose, CA 95134, USA Building 3, University Technology Centre Curraheen Road, Cork, Ireland February 2018 16

Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Industry Canada statement: This device complies with ISED’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable. Radiation Exposure Statement: This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Déclaration d'exposition aux radiations: Cet équipement est conforme aux limites d'exposition aux rayonnements ISED établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.


Document Created: 2018-03-31 13:10:57
Document Modified: 2018-03-31 13:10:57
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC