Test Report (co-located)_rev 3.pdf

FCC ID: PY315200317

Test Report

Download: PDF
FCCID_2954327

FCC Test Report (Co-Located) Report No.: RF160205C08-2 FCC ID: PY315200317 Test Model: EX7300 Received Date: Feb. 04, 2016 Test Date: Apr. 07, 2016 Issued Date: Apr. 07, 2016 Applicant: NETGEAR, INC. Address: 350 East Plumeria Drive San Jose, CA 95134 Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan (R.O.C.) Test Location: No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, TAIWAN (R.O.C.) This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF160205C08-2 Page No. 1 / 29 Report Format Version: 6.1.1

Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity...................................................................................................................... 4 2 Summary of Test Results ..................................................................................................................... 5 2.1 Measurement Uncertainty ................................................................................................................... 5 2.2 Modification Record ............................................................................................................................ 5 3 General Information .............................................................................................................................. 6 3.1 General Description of EUT ................................................................................................................ 6 3.2 Description of Test Modes ................................................................................................................... 8 3.2.1 Test Mode Applicability and Tested Channel Detail ........................................................................... 10 3.3 Description of Support Units .............................................................................................................. 11 3.3.1 Configuration of System under Test ................................................................................................... 11 3.4 General Description of Applied Standards ......................................................................................... 11 4 Test Types and Results ...................................................................................................................... 12 4.1 Radiated Emission and Bandedge Measurement............................................................................. 12 4.1.1 Limits of Radiated Emission and Bandedge Measurement .............................................................. 12 4.1.2 Test Instruments ................................................................................................................................ 13 4.1.3 Test Procedures................................................................................................................................. 14 4.1.4 Deviation from Test Standard ............................................................................................................ 14 4.1.5 Test Setup .......................................................................................................................................... 15 4.1.6 EUT Operating Conditions................................................................................................................. 15 4.1.7 Test Results ....................................................................................................................................... 16 4.2 Conducted Emission Measurement .................................................................................................. 22 4.2.1 Limits of Conducted Emission Measurement .................................................................................... 22 4.2.2 Test Instruments ................................................................................................................................ 22 4.2.3 Test Procedures................................................................................................................................. 22 4.2.4 Deviation from Test Standard ............................................................................................................ 22 4.2.5 Test Setup .......................................................................................................................................... 23 4.2.6 EUT Operating Conditions................................................................................................................. 23 4.2.7 Test Results ....................................................................................................................................... 24 5 Pictures of Test Arrangements .......................................................................................................... 28 Appendix – Information on the Testing Laboratories ................................................................................ 29 Report No.: RF160205C08-2 Page No. 2 / 29 Report Format Version: 6.1.1

Release Control Record Issue No. Description Date Issued RF160205C08-2 Original release. Apr. 07, 2016 Report No.: RF160205C08-2 Page No. 3 / 29 Report Format Version: 6.1.1

1 Certificate of Conformity Product: Nighthawk X4 AC2200 WiFi Range Extender Brand: NETGEAR Test Model: EX7300 Sample Status: Engineering sample Applicant: NETGEAR, INC. Test Date: Apr. 07, 2016 Standards: 47 CFR FCC Part 15, Subpart C (Section 15.247) 47 CFR FCC Part 15, Subpart E (Section 15.407) ANSI C63.10:2013 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. Prepared by : , Date: Apr. 07, 2016 Suntee Liu / Specialist Approved by : , Date: Apr. 07, 2016 Ken Liu / Senior Manager Report No.: RF160205C08-2 Page No. 4 / 29 Report Format Version: 6.1.1

2 Summary of Test Results 47 CFR FCC Part 15, Subpart C (Section 15.247) 47 CFR FCC Part 15, Subpart E (Section 15.407) FCC Test Item Result Remarks Clause 15.207 Meet the requirement of limit. AC Power Conducted Emission PASS Minimum passing margin is -13.19dB 15.407(b)(6) at 0.53400MHz. 15.205 / 15.209 / Meet the requirement of limit. 15.247(d) Radiated Emission PASS Minimum passing margin is -0.3dB at 15.407(b) 15600.00MHz. (1/2/3/4/6) 2.1 Measurement Uncertainty Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16-4-2: Expended Uncertainty Measurement Frequency (k=2) (±) Conducted Emissions at mains ports 150kHz ~ 30MHz 2.44 dB 30MHz ~ 200MHz 3.59 dB Radiated Emissions up to 1 GHz 200MHz ~1000MHz 3.60 dB 1GHz ~ 18GHz 2.29 dB Radiated Emissions above 1 GHz 18GHz ~ 40GHz 2.29 dB 2.2 Modification Record There were no modifications required for compliance. Report No.: RF160205C08-2 Page No. 5 / 29 Report Format Version: 6.1.1

3 General Information 3.1 General Description of EUT Product Nighthawk X4 AC2200 WiFi Range Extender Brand NETGEAR Test Model EX7300 Status of EUT Engineering sample Power Supply Rating 100-240Vac, 0.3A, 50/60Hz CCK, DQPSK, DBPSK for DSSS Modulation Type 256QAM, 64QAM, 16QAM, QPSK, BPSK for OFDM Modulation Technology DSSS, OFDM 802.11b:11/5.5/2/1Mbps 802.11a/g: 54/48/36/24/18/12/9/6Mbps Transfer Rate 802.11n: up to 600Mbps 802.11ac: up to 1733Mbps 2.4GHz: 2412 ~ 2462MHz Operating Frequency 5.0GHz: 5180 ~ 5240MHz, 5745 ~ 5825MHz 2412 ~ 2462MHz: 11 for 802.11b, 802.11g, 802.11n (HT20) 7 for 802.11n (HT40) 5180 ~ 5240MHz: 4 for 802.11a, 802.11n (HT20), 802.11ac (VHT20) Number of Channel 2 for 802.11n (HT40), 802.11ac (VHT40) 1 for 802.11ac (VHT80) 5745 ~ 5825MHz: 5 for 802.11a, 802.11n (HT20), 802.11ac (VHT20) 2 for 802.11n (HT40), 802.11ac (VHT40) 1 for 802.11ac (VHT80) 2412~2462MHz: 562.644mW CDD Mode: 5180 ~ 5240MHz: 636.257mW Output Power 5745 ~ 5825MHz: 751.864mW Beamforming Mode: 5180 ~ 5240MHz: 508.828mW 5745 ~ 5825MHz: 429.555mW Antenna Type Refer to Note Antenna Connector Refer to Note Accessory Device NA Data Cable Supplied NA Report No.: RF160205C08-2 Page No. 6 / 29 Report Format Version: 6.1.1

Note: 1. The EUT incorporates a MIMO function. Physically, the EUT provides 4 completed transmitters and 4 receivers. Band Modulation Mode Beamforming Mode TX Function 802.11b Not Support 3TX 802.11g Not Support 3TX 2.4GHz 802.11n (HT20) Not Support 3TX 802.11n (HT40) Not Support 3TX 802.11a Not Support 4TX 802.11n (HT20) Support 4TX 802.11n (HT40) Support 4TX 5GHz 802.11ac (VHT20) Support 4TX 802.11ac (VHT40) Support 4TX 802.11ac (VHT80) Support 4TX * The modulation and bandwidth are similar for 802.11n mode for 20MHz/40MHz and 802.11ac mode for 20MHz/40MHz, therefore investigated worst case to representative mode in test report. (Final test mode refer section 3.2.1) * For 5GHz band 802.11n and 802.11ac, CDD mode is the worst case for final radiated emission and power line conducted emission tests after pretesting CDD mode and beamforming mode. 2. The EUT uses following antennas. Antenna Antenna Chain 0/1/2: PIFA, Chain 3: PCB NA Type Connector Antenna Gain (dBi) Frequency (MHz) Chain 2412 2422 2437 2452 2462 5180 5200 5240 5190 5230 5210 5745 5785 5825 5755 5795 5775 0 2.5 2.5 3 3.5 4 1.7 2.2 2.5 1.9 2.2 2.2 3.7 4 4 3.9 4 4 1 1.5 1.7 2.1 2.3 2.4 3.6 3.6 3.8 3.6 3.7 3.7 4 4.2 4.1 4.1 4.2 4.2 2 3.1 3.3 3.6 4 4 2.6 2.7 3.1 2.6 3 3 2.5 2.9 3.1 2.5 3 2.9 3 - - - - - 2.3 2.4 2.5 2.3 2.5 2.4 3.2 3 3.2 3.2 3.1 3 Report No.: RF160205C08-2 Page No. 7 / 29 Report Format Version: 6.1.1

3.2 Description of Test Modes FOR 2.4GHz 11 channels are provided for 802.11b, 802.11g and 802.11n (HT20): Channel Frequency Channel Frequency 1 2412MHz 7 2442MHz 2 2417MHz 8 2447MHz 3 2422MHz 9 2452MHz 4 2427MHz 10 2457MHz 5 2432MHz 11 2462MHz 6 2437MHz 7 channels are provided for 802.11n (HT40): Channel Frequency Channel Frequency 3 2422MHz 7 2442MHz 4 2427MHz 8 2447MHz 5 2432MHz 9 2452MHz 6 2437MHz FOR 5180 ~ 5240MHz 4 channels are provided for 802.11a, 802.11n (HT20), 802.11ac (VHT20): Channel Frequency Channel Frequency 36 5180 MHz 44 5220 MHz 40 5200 MHz 48 5240 MHz 2 channels are provided for 802.11n (HT40), 802.11ac (VHT40): Channel Frequency Channel Frequency 38 5190 MHz 46 5230 MHz 1 channel is provided for 802.11ac (VHT80): Channel Frequency 42 5210MHz Report No.: RF160205C08-2 Page No. 8 / 29 Report Format Version: 6.1.1

FOR 5745 ~ 5825MHz 5 channels are provided for 802.11a, 802.11n (HT20), 802.11ac (VHT20): Channel Frequency Channel Frequency 149 5745MHz 161 5805MHz 153 5765MHz 165 5825MHz 157 5785MHz 2 channels are provided for 802.11n (HT40), 802.11ac (VHT40): Channel Frequency Channel Frequency 151 5755MHz 159 5795MHz 1 channel is provided for 802.11ac (VHT80): Channel Frequency 155 5775MHz Report No.: RF160205C08-2 Page No. 9 / 29 Report Format Version: 6.1.1

3.2.1 Test Mode Applicability and Tested Channel Detail EUT Configure Applicable to Description Mode RE1G RE<1G PLC A, B √ √ √ Refer to each test item Where RE1G: Radiated Emission above 1GHz & Bandedge RE<1G: Radiated Emission below 1GHz Measurement PLC: Power Line Conducted Emission Note: The EUT had been pre-tested on the positioned of each 3 axis. The worst case was found when positioned on X-plane for 2.4GHz and Z-plane for 5GHz. Radiated Emission Test (Above 1GHz): Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT Configure Frequency Band Mode Available Channel Tested Channel Modulation Technology Mode (MHz) 802.11n (HT20) 2412-2462 1 to 11 6 OFDM A 802.11a 5180-5240 36 to 48 40 OFDM 802.11n (HT20) 2412-2462 1 to 11 6 OFDM B 802.11a 5745-5825 149 to 165 157 OFDM Radiated Emission Test (Below 1GHz): Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT Configure Frequency Band Mode Available Channel Tested Channel Modulation Technology Mode (MHz) 802.11n (HT20) 2412-2462 1 to 11 6 OFDM A 802.11a 5180-5240 36 to 48 40 OFDM 802.11n (HT20) 2412-2462 1 to 11 6 OFDM B 802.11a 5745-5825 149 to 165 157 OFDM Power Line Conducted Emission Test: Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT Configure Frequency Band Mode Available Channel Tested Channel Modulation Technology Mode (MHz) 802.11n (HT20) 2412-2462 1 to 11 6 OFDM A 802.11a 5180-5240 36 to 48 40 OFDM 802.11n (HT20) 2412-2462 1 to 11 6 OFDM B 802.11a 5745-5825 149 to 165 157 OFDM Test Condition: Applicable to Environmental Conditions Input Power Tested by RE1G 23 deg. C, 63% RH 120Vac, 60Hz Alan Wu RE<1G 23 deg. C, 63% RH 120Vac, 60Hz Alan Wu PLC 23 deg. C, 63% RH 120Vac, 60Hz Alan Wu Report No.: RF160205C08-2 Page No. 10 / 29 Report Format Version: 6.1.1

3.3 Description of Support Units The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. ID Product Brand Model No. Serial No. FCC ID Remarks A. Notebook DELL E5410 BPQ7MQ1 FCC DoC Approved - Note: 1. All power cords of the above support units are non-shielded (1.8m). 2. Item A acted as a communication partner to transfer data. Shielding ID Descriptions Qty. Length (m) Cores (Qty.) Remarks (Yes/No) 1. RJ45 1 5 N 0 - 3.3.1 Configuration of System under Test EUT (1) Remote site Notebook (A) 3.4 General Description of Applied Standards The EUT is a RF Product. According to the specification of the EUT declared by the manufacturer, it must comply with the requirements of the following standards: FCC Part 15, Subpart C (15.247) FCC Part 15, Subpart E (15.407) ANSI C63.10-2013 All test items have been performed and recorded as per the above standards. Note: The EUT has been verified to comply with the requirements of FCC Part 15, Subpart B, Class B (DoC). The test report has been issued separately. Report No.: RF160205C08-2 Page No. 11 / 29 Report Format Version: 6.1.1

4 Test Types and Results 4.1 Radiated Emission and Bandedge Measurement 4.1.1 Limits of Radiated Emission and Bandedge Measurement Radiated emissions which fall in the restricted bands must comply with the radiated emission limits specified as below table. Other emissions shall be at least 20dB below the highest level of the desired power: Frequencies (MHz) Field Strength (microvolts/meter) Measurement Distance (meters) 0.009 ~ 0.490 2400/F(kHz) 300 0.490 ~ 1.705 24000/F(kHz) 30 1.705 ~ 30.0 30 30 30 ~ 88 100 3 88 ~ 216 150 3 216 ~ 960 200 3 Above 960 500 3 NOTE: 1. The lower limit shall apply at the transition frequencies. 2. Emission level (dBuV/m) = 20 log Emission level (uV/m). 3. For frequencies above 1000MHz, the field strength limits are based on average detector, however, the peak field strength of any emission shall not exceed the maximum permitted average limits, specified above by more than 20dB under any condition of modulation. Limits of Unwanted Emission Out of The Restricted Bands Applicable To Limit Field Strength at 3m 789033 D02 General UNII Test Procedures New Rules v01r01 PK:74 (dBµV/m) AV:54 (dBµV/m) Applicable To EIRP Limit Equivalent Field Strength at 3m 15.407(b)(1) 15.407(b)(2) PK: -27 (dBm/MHz) PK: 68.2 (dBµV/m) 15.407(b)(3) PK: -27 (dBm/MHz) *1 PK: 68.2 (dBµV/m) *1 15.407(b)(4) PK: -17 (dBm/MHz) *2 PK: 78.2 (dBµV/m) *2 NOTE: *1 beyond 10MHz of the band edge *2 within 10 MHz of band edge The following formula is used to convert the equipment isotropic radiated power (eirp) to field strength: 1000000 30 P E= µV/m, where P is the eirp (Watts). 3 Report No.: RF160205C08-2 Page No. 12 / 29 Report Format Version: 6.1.1

4.1.2 Test Instruments Description & Model No. Serial No. Cal. Date Cal. Due Manufacturer Test Receiver ESCI 100424 Oct. 12, 2015 Oct. 11, 2016 ROHDE & SCHWARZ Spectrum Analyzer FSP40 100040 Jul. 08, 2015 Jul. 07, 2016 ROHDE & SCHWARZ BILOG Antenna VULB9168 9168-155 Jan. 07, 2016 Jan. 06, 2017 SCHWARZBECK HORN Antenna BBHA 9120D 9120D-1170 Jan. 08, 2016 Jan. 07, 2017 SCHWARZBECK HORN Antenna BBHA 9170 BBHA9170241 Jan. 18, 2016 Jan. 17, 2017 SCHWARZBECK Preamplifier 8449B 3008A01960 Aug. 09, 2015 Aug. 08, 2016 Agilent Preamplifier 8447D 2944A10631 Aug. 09, 2015 Aug. 08, 2016 Agilent RF signal cable Cable-CH4-02(295012+ SUCOFLEX 104 Aug. 09, 2015 Aug. 08, 2016 HUBER+SUHNER 309220) RF signal cable SUCOFLEX 104 Cable-CH4-03(250724) Aug. 09, 2015 Aug. 08, 2016 HUBER+SUHNER Software ADT_Radiated_ NA NA NA BV ADT V7.6.15.9.4 Antenna Tower MA 4000 010303 NA NA inn-co GmbH Antenna Tower Controller AT100 AT93021703 NA NA BV ADT Turn Table TT100 TT93021703 NA NA BV ADT Turn Table Controller SC100. SC93021703 NA NA BV ADT High Speed Peak Power ML2495A 0824011 Jul. 09, 2015 Jul. 08, 2016 Meter Power Sensor MA2411B 0738171 Jul. 09, 2015 Jul. 08, 2016 Note: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in HwaYa Chamber 4. 3. The horn antenna and preamplifier (model: 8449B) are used only for the measurement of emission frequency above 1GHz if tested. 4. The FCC Site Registration No. is 460141. 5. The IC Site Registration No. is IC7450F-4. Report No.: RF160205C08-2 Page No. 13 / 29 Report Format Version: 6.1.1

4.1.3 Test Procedures a. The EUT was placed on the top of a rotating table 0.8 meters (for below 1GHz) / 1.5 meters (for above 1GHz) above the ground at 3 meter chamber room for test. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The height of antenna is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to quasi-peak detect function and specified bandwidth with maximum hold mode when the test frequency is below 1 GHz. f. The test-receiver system was set to peak and average detect function and specified bandwidth with maximum hold mode when the test frequency is above 1 GHz. If the peak reading value also meets average limit, measurement with the average detector is unnecessary. Note: 1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120kHz for Quasi-peak detection (QP) at frequency below 1GHz. 2. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and the video bandwidth is 3 MHz for Peak detection (PK) at frequency above 1GHz. 3. The resolution bandwidth of test receiver/spectrum analyzer is 1MHz and the video bandwidth is 3MHz for RMS Average (Duty cycle < 98%) for Average detection (AV) at frequency above 1GHz, then the measurement results was added to a correction factor (10 log(1/duty cycle)). 4. The resolution bandwidth of test receiver/spectrum analyzer is 1MHz and the video bandwidth is 10Hz (Duty cycle ≥ 98%) for Average detection (AV) at frequency above 1GHz. 5. All modes of operation were investigated and the worst-case emissions are reported. 4.1.4 Deviation from Test Standard No deviation. Report No.: RF160205C08-2 Page No. 14 / 29 Report Format Version: 6.1.1

4.1.5 Test Setup <Frequency Range 30MHz~1GHz> Ant. Tower 1-4m Variable EUT& 3m 10m Support Units Turn Table 80cm Ground Plane Test Receiver <Frequency Range above 1GHz> Ant. Tower 1-4m Variable EUT& 3m Support Units Turn Table Absorber 150cm Ground Plane Test Receiver For the actual test configuration, please refer to the attached file (Test Setup Photo). 4.1.6 EUT Operating Conditions a. Placed the EUT on the testing table. b. Prepared a notebook to act as a communication partner and placed it outside of testing area. c. The communication partner connected with EUT via a RJ45 cable and ran a test program (provided by manufacturer) to enable EUT under transmission condition continuously at specific channel frequency. d. The communication partner sent data to EUT by command "PING". e. The necessary accessories enable the system in full functions. Report No.: RF160205C08-2 Page No. 15 / 29 Report Format Version: 6.1.1

4.1.7 Test Results Above 1GHz Data 802.11n (HT20) CH 6 + DETECTOR Peak (PK) CHANNEL 802.11a CH 40 FUNCTION Average (AV) FREQUENCY RANGE 1GHz ~ 25GHz TEST MODE A ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION LIMIT MARGIN NO. FREQ. (MHz) LEVEL HEIGHT ANGLE VALUE FACTOR (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 *2437.00 118.2 PK 1.67 H 142 86.00 32.20 2 *2437.00 108.8 AV 1.67 H 142 76.60 32.20 3 4874.00 60.0 PK 74.0 -14.0 1.00 H 146 53.40 6.60 4 4874.00 46.0 AV 54.0 -8.0 1.00 H 146 39.40 6.60 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION LIMIT MARGIN NO. FREQ. (MHz) LEVEL HEIGHT ANGLE VALUE FACTOR (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 *2437.00 116.2 PK 1.66 V 68 84.00 32.20 2 *2437.00 106.7 AV 1.66 V 68 74.50 32.20 3 4874.00 58.7 PK 74.0 -15.3 1.00 V 236 52.10 6.60 4 4874.00 45.1 AV 54.0 -8.9 1.00 V 236 38.50 6.60 REMARKS: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level – Limit value 5. " * ": Fundamental frequency. Report No.: RF160205C08-2 Page No. 16 / 29 Report Format Version: 6.1.1

802.11n (HT20) CH 6 + DETECTOR Peak (PK) CHANNEL 802.11a CH 40 FUNCTION Average (AV) FREQUENCY RANGE 1GHz ~ 25GHz TEST MODE A ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION LIMIT MARGIN NO. FREQ. (MHz) LEVEL HEIGHT ANGLE VALUE FACTOR (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 *5200.00 119.8 PK 1.56 H 194 80.20 39.60 2 *5200.00 109.4 AV 1.56 H 194 69.80 39.60 3 #10400.00 61.1 PK 74.0 -12.9 1.00 H 82 43.10 18.00 4 #10400.00 48.6 AV 54.0 -5.4 1.00 H 82 30.60 18.00 5 15600.00 65.6 PK 74.0 -8.4 1.25 H 3 46.90 18.70 6 15600.00 53.7 AV 54.0 -0.3 1.25 H 3 35.00 18.70 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION LIMIT MARGIN NO. FREQ. (MHz) LEVEL HEIGHT ANGLE VALUE FACTOR (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 *5200.00 118.3 PK 1.02 V 151 78.70 39.60 2 *5200.00 107.7 AV 1.02 V 151 68.10 39.60 3 #10400.00 61.3 PK 74.0 -12.7 1.00 V 174 43.30 18.00 4 #10400.00 48.2 AV 54.0 -5.8 1.00 V 174 30.20 18.00 5 15600.00 65.0 PK 74.0 -9.0 1.14 V 51 46.30 18.70 6 15600.00 53.6 AV 54.0 -0.4 1.14 V 51 34.90 18.70 REMARKS: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level – Limit value 5. " * ": Fundamental frequency. 6. " # ": The radiated frequency is out of the restricted band. Report No.: RF160205C08-2 Page No. 17 / 29 Report Format Version: 6.1.1

802.11n (HT20) CH 6 + DETECTOR Peak (PK) CHANNEL 802.11a CH 157 FUNCTION Average (AV) FREQUENCY RANGE 1GHz ~ 25GHz TEST MODE B ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION LIMIT MARGIN NO. FREQ. (MHz) LEVEL HEIGHT ANGLE VALUE FACTOR (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 *2437.00 118.6 PK 1.63 H 226 86.40 32.20 2 *2437.00 108.4 AV 1.63 H 226 76.20 32.20 3 4874.00 59.7 PK 74.0 -14.3 1.00 H 140 53.10 6.60 4 4874.00 46.3 AV 54.0 -7.7 1.00 H 140 39.70 6.60 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION LIMIT MARGIN NO. FREQ. (MHz) LEVEL HEIGHT ANGLE VALUE FACTOR (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 *2437.00 115.8 PK 1.62 V 84 83.60 32.20 2 *2437.00 106.3 AV 1.62 V 84 74.10 32.20 3 4874.00 58.5 PK 74.0 -15.5 1.00 V 196 51.90 6.60 4 4874.00 45.3 AV 54.0 -8.7 1.00 V 196 38.70 6.60 REMARKS: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level – Limit value 5. " * ": Fundamental frequency. Report No.: RF160205C08-2 Page No. 18 / 29 Report Format Version: 6.1.1

802.11n (HT20) CH 6 + DETECTOR Peak (PK) CHANNEL 802.11a CH 157 FUNCTION Average (AV) FREQUENCY RANGE 1GHz ~ 25GHz TEST MODE B ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION LIMIT MARGIN NO. FREQ. (MHz) LEVEL HEIGHT ANGLE VALUE FACTOR (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 *5785.00 121.0 PK 1.66 H 179 80.50 40.50 2 *5785.00 111.6 AV 1.66 H 179 71.10 40.50 3 11570.00 61.5 PK 74.0 -12.5 1.71 H 53 42.50 19.00 4 11570.00 48.3 AV 54.0 -5.7 1.71 H 53 29.30 19.00 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION LIMIT MARGIN NO. FREQ. (MHz) LEVEL HEIGHT ANGLE VALUE FACTOR (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 *5785.00 116.3 PK 3.40 V 327 75.80 40.50 2 *5785.00 105.9 AV 3.40 V 327 65.40 40.50 3 11570.00 59.4 PK 74.0 -14.6 1.77 V 49 40.40 19.00 4 11570.00 47.0 AV 54.0 -7.0 1.77 V 49 28.00 19.00 REMARKS: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level – Limit value 5. " * ": Fundamental frequency. 6. " # ": The radiated frequency is out of the restricted band. Report No.: RF160205C08-2 Page No. 19 / 29 Report Format Version: 6.1.1

Below 1GHz data 802.11n (HT20) CH 6 + DETECTOR CHANNEL Quasi-Peak (QP) 802.11a CH 40 FUNCTION FREQUENCY RANGE 30MHz ~ 1GHz TEST MODE A ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION LIMIT MARGIN NO. FREQ. (MHz) LEVEL HEIGHT ANGLE VALUE FACTOR (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 37.66 31.4 QP 40.0 -8.6 1.99 H 13 46.10 -14.70 2 124.98 39.5 QP 43.5 -4.0 1.99 H 163 55.30 -15.80 3 249.17 42.4 QP 46.0 -3.6 1.00 H 292 57.00 -14.60 4 301.56 35.9 QP 46.0 -10.1 1.00 H 166 48.60 -12.70 5 375.29 32.9 QP 46.0 -13.1 1.00 H 261 44.40 -11.50 6 625.60 34.7 QP 46.0 -11.3 1.24 H 186 41.30 -6.60 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION LIMIT MARGIN NO. FREQ. (MHz) LEVEL HEIGHT ANGLE VALUE FACTOR (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 57.07 32.1 QP 40.0 -7.9 1.00 V 7 46.30 -14.20 2 124.98 31.7 QP 43.5 -11.8 1.00 V 320 47.50 -15.80 3 198.71 32.7 QP 43.5 -10.8 1.00 V 223 49.30 -16.60 4 249.17 40.2 QP 46.0 -5.8 1.50 V 221 54.80 -14.60 5 375.29 33.0 QP 46.0 -13.0 1.24 V 248 44.50 -11.50 6 625.60 33.3 QP 46.0 -12.7 1.00 V 261 39.90 -6.60 REMARKS: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level – Limit value Report No.: RF160205C08-2 Page No. 20 / 29 Report Format Version: 6.1.1

802.11n (HT20) CH 6 + DETECTOR CHANNEL Quasi-Peak (QP) 802.11a CH 157 FUNCTION FREQUENCY RANGE 30MHz ~ 1GHz TEST MODE B ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION LIMIT MARGIN NO. FREQ. (MHz) LEVEL HEIGHT ANGLE VALUE FACTOR (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 37.66 33.5 QP 40.0 -6.5 2.00 H 13 48.20 -14.70 2 124.98 38.7 QP 43.5 -4.8 2.00 H 167 54.50 -15.80 3 198.71 32.0 QP 43.5 -11.5 1.00 H 291 48.60 -16.60 4 249.17 42.2 QP 46.0 -3.8 1.00 H 291 56.80 -14.60 5 299.62 34.6 QP 46.0 -11.4 1.24 H 183 47.40 -12.80 6 625.60 34.0 QP 46.0 -12.0 1.24 H 192 40.60 -6.60 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION LIMIT MARGIN NO. FREQ. (MHz) LEVEL HEIGHT ANGLE VALUE FACTOR (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 53.18 31.7 QP 40.0 -8.3 1.00 V 19 45.50 -13.80 2 124.98 32.1 QP 43.5 -11.4 1.00 V 341 47.90 -15.80 3 198.71 31.0 QP 43.5 -12.5 1.00 V 203 47.60 -16.60 4 249.17 40.1 QP 46.0 -5.9 1.50 V 225 54.70 -14.60 5 416.04 32.4 QP 46.0 -13.6 1.00 V 171 43.30 -10.90 6 625.60 32.3 QP 46.0 -13.7 1.00 V 256 38.90 -6.60 REMARKS: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level – Limit value Report No.: RF160205C08-2 Page No. 21 / 29 Report Format Version: 6.1.1

4.2 Conducted Emission Measurement 4.2.1 Limits of Conducted Emission Measurement Conducted Limit (dBuV) Frequency (MHz) Quasi-peak Average 0.15 - 0.5 66 - 56 56 - 46 0.50 - 5.0 56 46 5.0 - 30.0 60 50 Note: 1. The lower limit shall apply at the transition frequencies. 2. The limit decreases in line with the logarithm of the frequency in the range of 0.15 to 0.50MHz. 4.2.2 Test Instruments Description & Manufacturer Model No. Serial No. Cal. Date Cal. Due Test Receiver ESCI 100613 Nov. 16, 2015 Nov. 15, 2016 ROHDE & SCHWARZ RF signal cable (with 10dB PAD) 5D-FB Cable-cond1-01 Dec. 26, 2015 Dec. 25, 2016 Woken LISN ROHDE & SCHWARZ ESH3-Z5 835239/001 Feb. 26, 2016 Feb. 25, 2017 (EUT) LISN ROHDE & SCHWARZ ESH3-Z5 100311 Jul. 24, 2015 Jul. 23, 2016 (Peripheral) Software BV ADT_Cond_ NA NA NA ADT V7.3.7.3 Note: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in HwaYa Shielded Room 1. 3. The VCCI Site Registration No. is C-2040. 4.2.3 Test Procedures a. The EUT was placed 0.4 meters from the conducting wall of the shielded room with EUT being connected to the power mains through a line impedance stabilization network (LISN). Other support units were connected to the power mains through another LISN. The two LISNs provide 50 ohm/ 50uH of coupling impedance for the measuring instrument. b. Both lines of the power mains connected to the EUT were checked for maximum conducted interference. c. The frequency range from 150kHz to 30MHz was searched. Emission levels under (Limit - 20dB) were not recorded. NOTE: The resolution bandwidth and video bandwidth of test receiver is 9kHz for quasi-peak detection (QP) and average detection (AV) at frequency 0.15MHz-30MHz. 4.2.4 Deviation from Test Standard No deviation. Report No.: RF160205C08-2 Page No. 22 / 29 Report Format Version: 6.1.1

4.2.5 Test Setup Vertical Ground Reference Plane Test Receiver EUT 40cm 80cm LISN Horizontal Ground Reference Plane Note: 1.Support units were connected to second LISN. For the actual test configuration, please refer to the attached file (Test Setup Photo). 4.2.6 EUT Operating Conditions Same as 4.1.6. Report No.: RF160205C08-2 Page No. 23 / 29 Report Format Version: 6.1.1

4.2.7 Test Results 802.11n (HT20) CH 6 + Quasi-Peak (QP) / CHANNEL Detector Function 802.11a CH 40 Average (AV) TEST MODE A Phase Of Power : Line (L) Frequency Correction Reading Value Emission Level Limit Margin No Factor (dBuV) (dBuV) (dBuV) (dB) (MHz) (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.15400 10.02 41.26 25.66 51.28 35.68 65.78 55.78 -14.50 -20.10 2 0.16535 10.05 41.24 27.61 51.29 37.66 65.19 55.19 -13.90 -17.53 3 0.17400 10.07 39.12 23.22 49.19 33.29 64.77 54.77 -15.58 -21.48 4 0.18600 10.09 39.15 25.33 49.24 35.42 64.21 54.21 -14.97 -18.79 5 0.24614 10.12 31.39 17.24 41.51 27.36 61.89 51.89 -20.37 -24.52 6 0.53404 10.17 26.41 18.39 36.58 28.56 56.00 46.00 -19.42 -17.44 Remarks: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level – Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value Report No.: RF160205C08-2 Page No. 24 / 29 Report Format Version: 6.1.1

802.11n (HT20) CH 6 + Quasi-Peak (QP) / CHANNEL Detector Function 802.11a CH 40 Average (AV) TEST MODE A Phase Of Power : Neutral (N) Frequency Correction Reading Value Emission Level Limit Margin No Factor (dBuV) (dBuV) (dBuV) (dB) (MHz) (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.16190 10.01 38.68 24.40 48.69 34.41 65.37 55.37 -16.67 -20.95 2 0.18519 10.03 37.89 25.69 47.92 35.72 64.25 54.25 -16.33 -18.53 3 0.20740 10.04 35.07 22.43 45.11 32.47 63.31 53.31 -18.19 -20.83 4 0.23000 10.06 31.86 18.80 41.92 28.86 62.45 52.45 -20.53 -23.59 5 0.53400 10.17 30.62 22.64 40.79 32.81 56.00 46.00 -15.21 -13.19 6 0.95400 10.22 17.97 9.27 28.19 19.49 56.00 46.00 -27.81 -26.51 Remarks: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level – Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value Report No.: RF160205C08-2 Page No. 25 / 29 Report Format Version: 6.1.1

802.11n (HT20) CH 6 + Quasi-Peak (QP) / CHANNEL Detector Function 802.11a CH 157 Average (AV) TEST MODE B Phase Of Power : Line (L) Frequency Correction Reading Value Emission Level Limit Margin No Factor (dBuV) (dBuV) (dBuV) (dB) (MHz) (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.16579 10.05 38.28 25.04 48.33 35.09 65.17 55.17 -16.84 -20.08 2 0.18600 10.09 36.07 23.01 46.16 33.10 64.21 54.21 -18.05 -21.11 3 0.20600 10.12 33.34 19.36 43.46 29.48 63.37 53.37 -19.90 -23.88 4 0.25742 10.12 28.29 14.77 38.41 24.89 61.51 51.51 -23.10 -26.62 5 0.53404 10.17 25.94 17.82 36.11 27.99 56.00 46.00 -19.89 -18.01 6 2.12600 10.28 11.97 4.34 22.25 14.62 56.00 46.00 -33.75 -31.38 Remarks: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level – Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value Report No.: RF160205C08-2 Page No. 26 / 29 Report Format Version: 6.1.1

802.11n (HT20) CH 6 + Quasi-Peak (QP) / CHANNEL Detector Function 802.11a CH 157 Average (AV) TEST MODE B Phase Of Power : Neutral (N) Frequency Correction Reading Value Emission Level Limit Margin No Factor (dBuV) (dBuV) (dBuV) (dB) (MHz) (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.16600 10.02 39.08 26.66 49.10 36.68 65.16 55.16 -16.06 -18.48 2 0.19000 10.03 36.19 22.63 46.22 32.66 64.04 54.04 -17.81 -21.37 3 0.21015 10.05 32.78 20.08 42.83 30.13 63.20 53.20 -20.37 -23.07 4 0.23800 10.06 30.45 18.35 40.51 28.41 62.17 52.17 -21.65 -23.75 5 0.53828 10.17 29.90 22.20 40.07 32.37 56.00 46.00 -15.93 -13.63 6 1.03400 10.23 18.11 9.45 28.34 19.68 56.00 46.00 -27.66 -26.32 Remarks: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level – Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value Report No.: RF160205C08-2 Page No. 27 / 29 Report Format Version: 6.1.1

5 Pictures of Test Arrangements Please refer to the attached file (Test Setup Photo). Report No.: RF160205C08-2 Page No. 28 / 29 Report Format Version: 6.1.1

Appendix – Information on the Testing Laboratories We, Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, were founded in 1988 to provide our best service in EMC, Radio, Telecom and Safety consultation. Our laboratories are accredited and approved according to ISO/IEC 17025. If you have any comments, please feel free to contact us at the following: Linko EMC/RF Lab Hsin Chu EMC/RF/Telecom Lab Tel: 886-2-26052180 Tel: 886-3-5935343 Fax: 886-2-26051924 Fax: 886-3-5935342 Hwa Ya EMC/RF/Safety Lab Tel: 886-3-3183232 Fax: 886-3-3270892 Email: service.adt@tw.bureauveritas.com Web Site: www.bureauveritas-adt.com The address and road map of all our labs can be found in our web site also. --- END --- Report No.: RF160205C08-2 Page No. 29 / 29 Report Format Version: 6.1.1


Document Created: 2017-11-23 06:09:01
Document Modified: 2017-11-23 06:09:01
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC