User Manual

FCC ID: PY312200202

Users Manual

Download: PDF
FCCID_1733487

c. Securely insert the other end of d. Select Configuration > IP > IP Settings from the menu and configure the the cable into an access point IP settings for your network. Installation Guide Ethernet port (point B in the illustration). A NETGEAR Cable e. If you use DHCP, reserve an IP address (based on the access point’s MAC address) on the DHCP server. You can then use that address to log in to d. Connect the power adapter to the the access point. access point. Verify the following: f. Select Configuration > Wireless > Basic > Wireless Settings and select ProSafe 3x3 Single Radio, Dual Band Wireless-N Access Point Ethernet The Power LED blinks when the access point is first turned on. B port the Turn Radio On setting. g. Select Configuration > Security > Profile Settings and configure security Package Contents After a few seconds it should stay on (steady green). If after 30 profiles for your network. See the online help or the Reference Manual for full instructions. Unpack the box and verify the contents: seconds the Power LED is off or is WNDAP620 still blinking, check the 3. Test wireless connectivity. • ProSafe 3x3 Single Radio, Dual Band Wireless-N Access Point connections and check to see if the power outlet is controlled by a wall Using a PC with a wireless adapter, verify that you can establish a wireless • Straight through Category 5 Ethernet cable switch that is turned off. connection to the access point. • Power adapter and cord (12V, 1.5A) The ACTIVE LED blinks when there is network traffic. Now that you have finished the setup, you are ready to deploy the access point • Ceiling mount kit in your network. If needed, you can reconfigure the PC you used in step 1 back The LAN LED indicates LAN speed for each of the two LAN ports; • Installation Guide to its original TCP/IP settings. green for 1000 Mbps, amber for 100Mbps, and no light for 10Mbps. • Resource CD, which includes link to the Reference Manual 2.4 GHz (WLAN). This LED indicates 2.4 GHz traffic. Deploy the Access Point Set Up the Access Point 5 GHz (WLAN). This LED indicates 5 GHz traffic. 1. Disconnect the access point and position it where you will deploy it. The best 2. Configure LAN and wireless access Follow these instructions to set up your wireless access point. Before proceeding location is elevated such as wall or ceiling mounted, at the center of your with the WNDAP620 installation, familiarize yourself with the contents of the a. From your PC, configure the access point Ethernet port for LAN access. wireless coverage area, and within line of sight of all mobile devices. Make Resource CD. See the Reference Manual for instructions on advanced Connect to the access point by opening your browser and entering sure the dome side of the AP points toward users. configuration options. http://192.168.0.100 in the address field. Tip: Before mounting the access point in a high location, first set up and test the unit to verify wireless network connectivity. 1. Connect the wireless access point to your computer. b. A login window displays. When a. Prepare a PC with an Ethernet adapter. If this PC is already part of your prompted, enter admin for the user network, record its TCP/IP configuration settings. Configure the PC with a name and password for the static IP address of 192.168.0.210 and 255.255.255.0 as the subnet mask. password, both in lower case letters. b. Connect an Ethernet cable from the access point to the PC (point A in the illustration). The access point user interface displays. Ceiling Mount Wall Mount c. Select Configuration > System > Basic > General from the menu. Fill in Note: DO NOT place the AP in a false ceiling space facing up. the Access Point Name field and select your Country/Region of operation from the drop-down list.

2. Connect an Ethernet cable from your access point to a LAN port on your • Make sure you are using the correct NETGEAR power adapter supplied with • You might not have restarted the computer with the wireless adapter to have router, switch, or hub. your wireless access point. TCP/IP changes take effect. Restart the computer. 3. Connect the power adapter to the wireless access point and plug the power • If using PoE, ensure that the PoE switch is providing power to the access point. • The computer with the wireless adapter might not have the correct TCP/IP adapter into a power outlet. The Power and LAN LEDs should go on. settings to communicate with the network. Restart the computer and check that The LINK/ACT LED is not on. TCP/IP is set up correctly for that network. The usual setting for Windows on the Tip: The access point supports Power over Ethernet (PoE). If you have There is a hardware connection problem. Network Properties is set to “Obtain an IP address automatically.” a switch that provides PoE, you do not need to use the power adapter to power the access point. This can be especially convenient when the • The wireless access point’s default values might not work with your network. • Make sure the cable connectors are securely plugged in to the access point and Check the wireless access point default configuration against the configuration access point is installed in a high location far from a power outlet. to the network device (hub, switch, or router). of other devices in your network. • Make sure the connected device is turned on. If the Ethernet link is a 10 Mbps • For full instructions on changing the default values of the wireless access point, Verify Wireless Connectivity link, then the 10/100/1000 light is off, but the Link/Act light blinks if traffic is see the Reference Manual. present. Using a computer with an 802.11b/g/n wireless adapter, verify connectivity by using a browser to connect to the Internet, or check for file and printer access on your The WLAN LEDs are off. Statement of Conditions network. The wireless connection is not working. In the interest of improving internal design, operational function, and/operability, Note: If you cannot connect, see Troubleshooting Tips in this guide or the • If a Wireless LAN activity LED stays off, disconnect the power adapter from its NETGEAR reserves the right to make changes to the product described in this Reference Manual. power source and then plug it in again. document without notice. NETGEAR does not assume any liability that may occur • Log in to the access point and verify that the radio is turned on. due to the use or application of the product(s) or circuit layout(s) described herein. If You Use an External Antenna • Contact NETGEAR if the Wireless LAN LED remains off. To use an external 2.4 GHz antenna: I cannot configure the access point from a browser. Technical Support 1. Mount the accessory antenna(s). Thank you for selecting NETGEAR products. Check these items: 2. Attach the antenna(s) to the connector(s) on the access point rear panel. • The access point is correctly installed, it is powered on, and LAN connections After installing your device, locate the serial number on the label of your product and 3. Log into the access point and configure it to use the external antenna. The are OK. Check that the LAN LED is on to verify that the Ethernet connection is use it to register your product at http://www.netgear.com/register. Registration is access point cannot use the internal and external 2.4GHz antennas at the OK. required before you can use our telephone support service. Registration via our web same time. • If you are using the Net BIOS name of the access point to connect, ensure that site is strongly recommended. your PC and the access point are on the same network segment or that there is Troubleshooting Tips a WINS server on your network. Go to http://kbserver.netgear.com for product updates and Web support. For Warranty and Regional Customer Support information, see the Resource CD that • If your PC uses a fixed (static) IP address, ensure that it is using an IP address No LEDs are lit on the access point. in the range of the access point. The access point default IP address is came with your product. 192.168.0.100 and the default subnet mask is 255.255.255.0. The access point For complete DoC please visit the NETGEAR EU Declarations of Conformity The wireless access point has no power. default setting is for a static IP address. If the network where you are connecting website at: http://kb.netgear.com/app/answers/detail/a_id/11621/ • Make sure the power cord is connected to the wireless access point and it is using DHCP, configure it accordingly. See the Reference Manual for details. plugged in to a working power outlet or power strip. I cannot access the Internet or the LAN with a wireless capable This symbol was placed in accordance with the European Union Directive 2002/96 on the Waste Electrical and Electronic Equipment (the WEEE Directive). If disposed of within the European Union, computer. this product should be treated and recycled in accordance with the laws of your jurisdiction implementing the WEEE Directive. There is a configuration problem. Check these items: NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered trademarks of June 2012 NETGEAR, Inc. and/or its subsidiaries in the United States and/or other countries. Information is subject to change without notice. Other brand and product names are registered trademarks or trademarks of their respective holders. © 2011 NETGEAR, Inc. All rights reserved.


Document Created: 2012-06-22 10:48:06
Document Modified: 2012-06-22 10:48:06
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC