test report 15407 1

FCC ID: PY305200015

Test Report

Download: PDF
FCCID_609021

                                                                    FCC Test Report: FE05080301-A




                          FCC TEST REPORT

                                           according to


                               FCC Rules and Regulations

                                   Part 15 Subpart E


             Applicant             Netgear Inc.
                                   4500 Great America Parkway Santa Clara
             Address
                                   California 95054 USA
             Equipment             ProSafe Dual Band Wireless Access Point
             Model No.             WAG102
             FCC ID                PY305200015
             Trade Name            Netgear
                                           Laboratory accreditation




                                                      1332



          The test result refers exclusively to the test presented test model / sample.,
          Without written approval of Exclusive Certification Corp. the test report shall not be
           reproduced except in full.
          The EUT is also considered as a kind of computer peripheral, because the connection to
           computer is necessary for typical use. It has been verified to comply with the requirements
           of FCC Part 15, Subpart B, Class B (DoC). The test report has been issued separately.




Exclusive Certification Corp. Tel:886-2-2792-3366 Fax:886-2-2792-1100    Issued date: Nov. 02, 2005   1 of 56


                                                                                             FCC Test Report: FE05080301-A

                                                                CONTENTS
   1.    Report of Measurements and Examinations ................................................................................. 5
         1.1.     List of Measurements and Examinations ............................................................................ 5
   2.    Test Configuration of Equipment under Test ................................................................................. 6
         2.1.     Feature of Equipment under Test....................................................................................... 6
         2.2.     RF Specifications .............................................................................................................. 7
         2.3.     Test Mode and Test Software ............................................................................................ 8
         2.4.     Description of Test System................................................................................................ 8
         2.5.     Connection Diagram of Test System .................................................................................. 9
   3.    General Information of Test ........................................................................................................10
         3.1.     History of this test report ..................................................................................................10
   4.    Antenna Requirements .............................................................................................................. 11
         4.1.     Standard Applicable ......................................................................................................... 11
         4.2.     Antenna Construction and Directional Gain ....................................................................... 11
   5.    Test of Conducted Emission .......................................................................................................12
         5.1.     Test Procedures ..............................................................................................................12
         5.2.     Typical Test Setup Layout of Conducted Emission .............................................................13
         5.3.     Conducted Emission Requirement ....................................................................................13
         5.4.     Test Result and Data .......................................................................................................14
   6.    Test of Radiated Emission ..........................................................................................................23
         6.1.     Test Procedures ..............................................................................................................23
         6.2.     Typical Test Setup Layout of Radiated Emission ................................................................23
         6.3.     Test Result of Radiated Emission .....................................................................................24
   7.    Peak Transmit Power.................................................................................................................36
         7.1.     Test Procedure................................................................................................................36
         7.2.     Test Setup Layout ............................................................................................................36
         7.3.     Test Result and Data .......................................................................................................36
   8.    Peak Power Excursion ...............................................................................................................41
         8.1.     Test Procedure................................................................................................................41
         8.2.     Test Setup Layout ............................................................................................................41
         8.3.     Test Result and Data .......................................................................................................41
   9.    Peak Power Spectral Density .....................................................................................................44
         9.1.     Test Procedure................................................................................................................44
         9.2.     Test Setup Layout ............................................................................................................44
         9.3.     Test Result and Data .......................................................................................................44
   10.   Frequency Stability ....................................................................................................................47
         10.1. Test Procedure................................................................................................................47
         10.2. Test Setup Layout ............................................................................................................47
         10.3. Test Result and Data .......................................................................................................48
   11.   Band Edges Measurement .........................................................................................................49
         11.1. Test Procedure................................................................................................................49
         11.2. Test Result and Data .......................................................................................................49
         11.3. Restrict Band Emission Measurement Data.......................................................................51
   12.   6dB Bandwidth............................................................................................ 錯誤! 尚未定義書籤?
         12.1. Test Procedure.................................................................................. 錯誤! 尚未定義書籤。
         12.2. Test Setup Layout .............................................................................. 錯誤! 尚未定義書籤。
         12.3. Test Result and Data ......................................................................... 錯誤! 尚未定義書籤。



Exclusive Certification Corp. Tel:886-2-2792-3366 Fax:886-2-2792-1100                               Issued date: Nov. 02, 2005          2 of 56


                                                                                             FCC Test Report: FE05080301-A

   13.   Maximum Peak Output Power ...................................................................... 錯誤! 尚未定義書籤?
         13.1. Test Procedure.................................................................................. 錯誤! 尚未定義書籤。
         13.2. Test Setup Layout .............................................................................. 錯誤! 尚未定義書籤。
         13.3. Test Result and Data ......................................................................... 錯誤! 尚未定義書籤。
   14.   Band Edges Measurement ........................................................................... 錯誤! 尚未定義書籤?
         14.1. Test Procedure.................................................................................. 錯誤! 尚未定義書籤。
         14.2. Test Result and Data ......................................................................... 錯誤! 尚未定義書籤。
   15.   Power Spectral Density................................................................................ 錯誤! 尚未定義書籤?
         15.1. Test Procedure.................................................................................. 錯誤! 尚未定義書籤。
         15.2. Test Setup Layout .............................................................................. 錯誤! 尚未定義書籤。
         15.3. Test Result and Data ......................................................................... 錯誤! 尚未定義書籤。
   16.   Restricted Bands of Operation....................................................................................................53
         16.1. Labeling Requirement ......................................................................................................53
   17.   RF Exposure.............................................................................................................................54
         17.1. Limit For Maximum Permissible Exposure (MPE) ..............................................................54
         17.2. MPE Calculations ............................................................................................................55
         17.3. FCC Radiation Exposure Statement..................................................................................55
   18. List of Measuring Equipment Used .............................................................................................56
   Appendix A. Photographs of EUT… … … … … … … … … … … … … … … … … … … … … … … … ..… … … … .A1 ~ A8




Exclusive Certification Corp. Tel:886-2-2792-3366 Fax:886-2-2792-1100                              Issued date: Nov. 02, 2005           3 of 56


                                                                       FCC Test Report: FE05080301-A




                       CERTIFICATE OF COMPLIANCE

                                                  according to


                                  FCC Rules and Regulations

                                        Part 15 Subpart C & E



          Applicant                Netgear Inc.
                                   4500 Great America Parkway Santa Clara
          Address
                                   California 95054 USA
          Equipment                ProSafe Dual Band Wireless Access Point
          Model No.                WAG102
          FCC ID                   PY305200015


            I HEREBY CERTIFY THAT :

            The measurements shown in this test report were made in accordance with the procedures
            given in ANSI C63.4 The equipment was passed the test performed according to FCC Rules
            and Regulations Part 15 Subpart C & E (2003).

            The test was carried out on Oct. 20, 2005 at Exclusive Certification Corp.



          Signature




        Anson Chou / Manager




Exclusive Certification Corp. Tel:886-2-2792-3366 Fax:886-2-2792-1100       Issued date: Nov. 02, 2005   4 of 56


                                                                    FCC Test Report: FE05080301-A

   1. Report of Measurements and Examinations

   1.1. List of Measurements and Examinations
       For Frequency 5.15GHz ~ 5.35GHZ
                     Applied Standard : FCC Part 15, Subpart E (Section 15.407)

               FCC Rule          . Description of Test                            Result

              15.407(b)(5)       . Conducted Emission                              Pass

         15.407(b/1/2/3)(b)(5)   . Radiated Emission                               Pass

            15.407(a/1/2/3)      . Peak Transmit Power                             Pass

              15.407(a)(6)       . Peak Power Excursion                            Pass

            15.407(a/1/2/3)      . Peak Power Spectral Density                     Pass

               15.407(g)         . Frequency Stability                             Pass




    Test engineer:




Exclusive Certification Corp. Tel:886-2-2792-3366 Fax:886-2-2792-1100   Issued date: Nov. 02, 2005   5 of 56


                                                                    FCC Test Report: FE05080301-A

   2. Test Configuration of Equipment under Test

       2.1. Feature of Equipment under Test

          Ÿ    Multiple Operating Modes
                - Wireless Access Point. Operates as a standard 802.11a/g.
                - Point-to-Point Bridge. In this mode, the WAG102 only communicates with another
                   bridge-mode wireless station. You must enter the MAC address (physical address) of the
                   other bridge-mode wireless station in the field provided. WEP should be used to protect
                   this communication.
                - Point-to-Multi-Point Bridge. Select this only if this WAG102 is the “Master” for a group
                   of bridge-mode wireless stations. The other bridge-mode wireless stations must be set to
                   Point-to-Point Bridge mode, using this WAG102's MAC address. They then send all
                   traffic to this “Master”, rather than communicate directly with each other. WEP should be
                   used to protect this traffic.
              -    Wireless Repeater. In this half-duplex mode, the WAG102 only communicates with
                     another repeater-mode wireless station. You must enter the MAC address of the root
                   access point. WEP should be used to protect this communication.
          Ÿ    Upgradeable Firmware. Firmware is stored in a flash memory and can be upgraded easily,
               using only your Web browser, and can be upgraded remotely.
          Ÿ    Access Control. The Access Control MAC address filtering feature can ensure that only
               trusted wireless stations can use the WAG102 to gain access to your LAN.
          Ÿ    Simple Configuration. If the default settings are unsuitable, they are easy to change.
          Ÿ    Hidden Mode . The SSID is not broadcast, assuring only clients configured with the correct
               SSID can connect.
          Ÿ    Secure Telnet Command Line Interface. The Telnet command line interface enables direct
               access over the serial port and easy scripting of configuration of multiple WAG102s across an
               extensive network via the Ethernet interface. An SSH client is required.
          Ÿ    Configuration Backup. Configuration settings can be backed up to a file and restored.
          Ÿ    Secure and Economical Operation. Adjustable power output allows more secure or
               economical operation.
          Ÿ    Power over Ethernet. Power can be supplied to the WAG102 over the Ethernet port from any
               802.3af compliant mid-span or end-span source such as the NETGEAR FSM7326P Managed
               Power over Ethernet Layer 3 managed switch.
          Ÿ    Autosensing Ethernet Connection with Auto Uplink Interface. Connects to 10/100 Mbps
               IEEE 802.3 Ethernet networks.
          Ÿ    LED Indicators. Power, test, LAN speed, LAN activity, and wireless activity are easily
               identified.




Exclusive Certification Corp. Tel:886-2-2792-3366 Fax:886-2-2792-1100   Issued date: Nov. 02, 2005   6 of 56


                                                                    FCC Test Report: FE05080301-A



       2.2.   RF Specifications


          Parameter                 WAG102 ProSafe Dual Band Wireless Access Point
          802.11a Data Rates        6, 9, 12, 18, 24, 36, 48, 54, and 108 Mbps (Auto-rate capable)
          802.11a                   5.15 ~ 5.25
          Operating                 5.25 ~ 5.35
          Frequencies               5.57 ~ 5.825
          802.11a Encryption        40-bit (also called 64-bit), 128- and 152-bit WEP data encryption
          802.11g Data Rates        1, 2, 5.5, 11, 12, 18, 24, 36, 38, 54, & 108 Mbps (Auto-rate capable)
          802.11g                   2.412 ~ 2.462 GHz (US) 2.457 ~ 2.462 GHz (Spain)
          Operating                 2.412 ~ 2.484 GHz (Japan)2.457 ~ 2.472 GHz (France)
          Frequencies               2.412 ~ 2.472 GHz (Europe ETSI)
          802.11g Encryption        40-bit (also called 64-bit), 128- and 152-bits WEP data encryption
          Network Management        Web-based configuration and status monitoring
          Maximum Clients           Limited by the amount of wireless network traffic generated by each
                                    node;
                                    typically 15 to 20 nodes.
          Status LEDs               Power/Ethernet LAN/Wireless LAN/Test
          Power Adapter             12V DC, 1 A
          Electromagnetic
                                    FCC Part 15 Class B and Class E, CE, and C-TICK
          Compliance
          Environmental             Operating temperature: 0 to 50° C
          Specifications            Operating humidity: 5-95%, non-condensing




Exclusive Certification Corp. Tel:886-2-2792-3366 Fax:886-2-2792-1100   Issued date: Nov. 02, 2005   7 of 56


                                                                    FCC Test Report: FE05080301-A


     2.3. Test Mode and Test Software
       The following test mode and test software was performed for conduction and radiation test:
        — 802.11 a (CH 36: Test Define CH1: 5180MHz)
         — 802.11 a (CH 48: Test Define CH4: 5240MHz)
         — 802.11a (CH 52: Test Define CH5: 5260MHz)
         — 802.11 a (CH 64: Test Define CH8: 5320MHz)
        — An executive programs, “ART.exe” Application under WIN XP
       The test mode of Radiated emission as below:
        — Test Model 1: Adapter: DSA-0131F-12
        — Test Model 2: PoE mode


     2.4. Description of Test System

            Device           Manufacturer       Model No.          Description

            PC               IBM                IGV                Power Cable, Unshielding 1.8 m

            Monitor          SlimAGE            510A               Power Cable, Adapter Unshielding 1.8 m

                                                                   Data Cable, VGA shielding 1.35 m

            Keyboard         IBM                KB-0225            Data Cable, PS2 shielding 1.85 m

            Mouse            IBM                MO28VO             Data Cable, USB shielding 1.85 m

            Modem            ACEXX              DM-1414            Power Cable, Adapter Unshielding 1.8 m

                                                                   Data Cable, RS232 shielding 1.35 m

            Printer          HP                 Desk Jet400        Power Cable, Adapter Unshielding 1.8 m

                                                                   Data Cable, PRINT shielding 1.6 m

            POE              Sercomm            FS108P             Power Cable, Adapter Unshielding 1.8 m

            (Remote site)


           Use Cable:
            Cable         Description
              RJ 45*1       Unshielding, 1.5m
              RJ 45*1        Unshielding, 5m




Exclusive Certification Corp. Tel:886-2-2792-3366 Fax:886-2-2792-1100    Issued date: Nov. 02, 2005   8 of 56


                                                                      FCC Test Report: FE05080301-A


     2.5. Connection Diagram of Test System



         Test mode 1:



                                                                                                                4
              3                       2                               1
              Printer              Modem                 EUT                      PC                      Monitor


                                                                              6                     5

                                                                          Keyboard


                                                                                               Mouse




                  1.    The RJ 45 cable is connected from PC to the EUT.
                  2.    The I/O cable is connected from PC to the Modem.
                  3.    The I/O cable is connected from PC to the Printer.
                  4.    The I/O cable is connected from PC to the Monitor.
                  5.    The I/O cable is connected from PC to the Mouse.
                  6.    The I/O cable is connected from PC to the Keyboard.




         Test model 2:


                                                    1
                                                                EUT




                                       POE



                  1. The RJ 45 cable is connected from PoE to the EUT.




Exclusive Certification Corp. Tel:886-2-2792-3366 Fax:886-2-2792-1100        Issued date: Nov. 02, 2005     9 of 56


                                                                    FCC Test Report: FE05080301-A


     3. General Information of Test

      Test Site:                          Exclusive Certification Corp.
                                          4F-2, No. 28, Lane 78, Xing-Ai Rd. Nei-hu, Taipei City 114
                                          Taiwan R.O.C.
      Test Site Location (OATS1-SD):      No.68-1, Shihbachongsi, shihding Township,
                                          Taipei City 223, Taiwan, R.O.C.

      Test Voltage:                       AC 120V/ 60Hz

      Test in Compliance with:            ANSI C63.4-2003
                                          FCC Part 15 Subpart C & E
      Frequency Range Investigated:       AC Power Conducted Emission : from 150kHz to 30 MHz
                                          Radiated and conducted Emission: from 30 MHz to 40 GHz
      Test Distance:                      The test distance of radiated emission from antenna to EUT is 3 M.




       3.1. History of this test report

            ORIGINAL.




Exclusive Certification Corp. Tel:886-2-2792-3366 Fax:886-2-2792-1100     Issued date: Nov. 02, 2005   10 of 56


                                                                    FCC Test Report: FE05080301-A


   4. Antenna Requirements


     4.1. Standard Applicable
           For intentional device, according to FCC 47 CFR Section 15.203, an intentional radiator shall be
           designed to ensure that no antenna other than that furnished by the responsible party shall be
           used with the device.

           And according to FCC 47 CFR Section 15.247 (b), if transmitting antennas of directional gain
           greater than 6dBi are used, the power shall be reduced by the amount in dB that the directional
           gain of the antenna exceeds 6dBi.


     4.2. Antenna Construction and Directional Gain
           Antenna type: Reverse SMA connect, Dipole antenna

           Antenna Gain: 5 dBi




Exclusive Certification Corp. Tel:886-2-2792-3366 Fax:886-2-2792-1100   Issued date: Nov. 02, 2005   11 of 56


                                                                     FCC Test Report: FE05080301-A


     5. Test of Conducted Emission

        Conducted Emissions were measured from 150 kHz to 30 MHz with a bandwidth of 9 KHz on the 115
        VAC power and return leads of the EUT according to the methods defined in ANSI C63.4-2003
        Section 3.1. The EUT was placed on a nonmetallic stand in a shielded room 0.8 meters above the
        ground plane as shown in section 1.3.1. The interface cables and equipment positioning were
        varied within limits of reasonable applications to determine the position produced maximum
        conducted emissions.




       5.1. Test Procedures

          a. The EUT was placed 0.4 meter from the conducting wall of the shielding room was kept at least
               80 centimeters from any other grounded conducting surface.
          b. Connect EUT to the power mains through a line impedance stabilization network (LISN).
          c.   All the support units are connecting to the other LISN.
          d. The LISN provides 50 ohm coupling impedance for the measuring instrument.
          e. The FCC states that a 50 ohm, 50 micro-Henry LISN should be used.
          f.   Both sides of AC line were checked for maximum conducted interference.
          g. The frequency range from 150 kHz to 30 MHz was searched.
          h. Set the test-receiver system to Peak Detect Function and Specified Bandwidth with Maximum
               Hold Mode.




Exclusive Certification Corp. Tel:886-2-2792-3366 Fax:886-2-2792-1100    Issued date: Nov. 02, 2005   12 of 56


                                                                    FCC Test Report: FE05080301-A

     5.2. Typical Test Setup Layout of Conducted Emission




                                         10cm




                       EUT



                                                                               80cm

                80cm


                               80cm


                                                           40cm
         LISN                                                                  LISN

                                                    40cm




     5.3. Conducted Emission Requirement

          Except for A digital devices, for equpment that is designed to be connected to the public utility (AC)
           power line on any frequency voltage that is conducted back onto the AC power line on ant
           frequency or frequencies within the band 150KHz to 30MHz shall not exceed the limits in the
           following table, as measured using a 50µH/50 ohms line impeddance stabilization network (LISN).
           Compliance with the provisions of this paragraph shall be based on the measurement of the Radio
           frequency voltage between each power line and ground at the power terminal. The lower limit
           applies at the band edges.


                 Frequency              Quasi Peak                Average
                   (MHz)                 (dB µ V)                 (dB µ V)
                 0.15 – 0.5               66-56*                   56-46*
                  0.5 – 5.0                 56                       46
                 5.0 – 30.0                 60                       50




Exclusive Certification Corp. Tel:886-2-2792-3366 Fax:886-2-2792-1100    Issued date: Nov. 02, 2005   13 of 56


                                                                    FCC Test Report: FE05080301-A


   5.4. Test Result and Data




Exclusive Certification Corp. Tel:886-2-2792-3366 Fax:886-2-2792-1100   Issued date: Nov. 02, 2005   14 of 56


                                                                    FCC Test Report: FE05080301-A




Exclusive Certification Corp. Tel:886-2-2792-3366 Fax:886-2-2792-1100   Issued date: Nov. 02, 2005   15 of 56


                                                                    FCC Test Report: FE05080301-A




Exclusive Certification Corp. Tel:886-2-2792-3366 Fax:886-2-2792-1100   Issued date: Nov. 02, 2005   16 of 56


                                                                    FCC Test Report: FE05080301-A




Exclusive Certification Corp. Tel:886-2-2792-3366 Fax:886-2-2792-1100   Issued date: Nov. 02, 2005   17 of 56


                                                                    FCC Test Report: FE05080301-A




Exclusive Certification Corp. Tel:886-2-2792-3366 Fax:886-2-2792-1100   Issued date: Nov. 02, 2005   18 of 56


                                                                    FCC Test Report: FE05080301-A




Exclusive Certification Corp. Tel:886-2-2792-3366 Fax:886-2-2792-1100   Issued date: Nov. 02, 2005   19 of 56


                                                                    FCC Test Report: FE05080301-A




Exclusive Certification Corp. Tel:886-2-2792-3366 Fax:886-2-2792-1100   Issued date: Nov. 02, 2005   20 of 56


                                                                    FCC Test Report: FE05080301-A




         Test engineer:




Exclusive Certification Corp. Tel:886-2-2792-3366 Fax:886-2-2792-1100   Issued date: Nov. 02, 2005   21 of 56


                                                                    FCC Test Report: FE05080301-A


   5.4.1. Photographs of Conducted Emission Test




           Front View




           Rear View




Exclusive Certification Corp. Tel:886-2-2792-3366 Fax:886-2-2792-1100   Issued date: Nov. 02, 2005   22 of 56


                                                                        FCC Test Report: FE05080301-A


   6. Test of Radiated Emission
        Radiated emissions from 30 MHz to 40 GHz were measured according to the methods defines in
        ANSI C63.4-2003. The EUT was placed, 0.8 meter above the ground plane, as shown in section
        1.4.2. The interface cables and equipment positions were varied within limits of reasonable
        applications to determine the positions producing maximum radiated emissions


     6.1. Test Procedures
       1. The EUT was placed on a rotatable table top 0.8 meter above ground.
       2. The EUT was set 3 meters from the interference receiving antenna which was mounted on the top
          of a variable height antenna tower.
       3. The table was rotated 360 degrees to determine the position of the highest radiation.
       4. The antenna is a broadband antenna and its height is varied between one meter and four meters
          above ground to find the maximum value of the field strength both horizontal polarization and
          vertical polarization of the antenna are set to make the measurement.
       5. For each suspected emission the EUT was arranged to its worst case and then tune the antenna
          tower (from 1 M to 4 M) and turn table (from 0 degree to 360 degrees) to find the maximum
          reading.
       6. Set the test-receiver system to Peak or CISPR quasi-peak Detect Function and specified
          bandwidth with Maximum Hold Mode.
       7. If the emission level of the EUT in peak mode was 3 dB lower than the limit specified, then testing
          will be stopped and peak values of EUT will be reported, otherwise, the emissions which do not
          have 3 dB margin will be repeated one by one using the quasi-peak method and reported.
       8. For testing above 1GHz, the emission level of the EUT in peak mode was 20dB lower than
          average limit (that means the emission level in peak mode also complies with the limit in average
          mode), then testing will be stopped and peak values of EUT will be reported, otherwise, the
          emissions will be measured in average mode again and reported.



     6.2. Typical Test Setup Layout of Radiated Emission
                            Antenna


                                                                            Equipment under Test




                                         *   Test distance

                                                                                                   0.8M
                                                                                 Turn Table




                                                             Ground Plane
      Receiver




Exclusive Certification Corp. Tel:886-2-2792-3366 Fax:886-2-2792-1100          Issued date: Nov. 02, 2005   23 of 56


                                                                    FCC Test Report: FE05080301-A


   6.3. Test Result of Radiated Emission
    Test Model 1: Adapter: DSA-0131F-12
    Emission frequencies below 1 GHz        Channel 01
    Test Date: Oct. 20, 2005    Temperature: 22℃         Humidity: 70%     Atmospheric pressure: 1020mmHg
                               Meter     Corrected                                                                 Ant
      Frequency     Ant-Pol                          Result@3m      Limit@3m Margin                      Table
                              Reading     Factor                                              Remark               High
         (MHz)        H/V                              (dBuV/m)     (dBuV/m)         (dB)                 Deg.
                               (dBuV)       (dB)                                                                   (m)
        143.30         H       52.72      -14.44         38.28           43.5       -5.22        Q.P       75      1.1
        150.73         H       49.13      -14.53         34.60           43.5       -8.90       Peak       75      1.1
        200.23         H       49.88      -17.09         32.78           43.5      -10.71       Peak        0      1.1
        232.80         H       52.17      -10.91         41.26           46.0       -4.74        Q.P       20      1.1
        248.30         H       52.60      -10.47         42.13           46.0       -3.87        Q.P      100      1.1
        249.18         H       56.10      -13.47         42.63           46.0       -3.37        Q.P        0      1.1
        598.90         H       46.77       -4.55         42.22           46.0       -3.87        Q.P      100      1.1
        997.90         H       45.88        2.78         48.66           54.0       -5.34        Q.P        0      1.1
        148.11         V       55.50      -14.43         41.07           43.5       -2.43        Q.P        0      1.0
        170.80         V       51.84      -16.83         35.01           43.5       -8.49       Peak        0      1.0
        194.73         V       52.75      -17.06         35.69           43.5       -7.81       Peak      215      1.0
        249.73         V       57.22      -13.36         43.86           46.0       -2.14        Q.P      200      1.0
        323.80         V       53.41      -10.91         42.50           46.0       -3.50        Q.P        0      1.0
        348.30         V       54.45      -10.47         43.98           46.0       -2.02        Q.P      215      1.0
        449.80         V       51.33       -8.81         42.52           46.0       -3.48        Q.P       30      1.0
        498.80         V       50.70       -7.05         43.65           46.0       -2.35        Q.P       30      1.0
     Notes:
     1. Result = Meter Reading + Corrected Factor
     2. Corrected Factor = Antenna Factor + Cable Loss – Amplifier
     3. The resolution bandwidth of test receiver/spectrum analyzer is 120 kHz and video bandwidth
         is 300 kHz for Peak detection and Quasi-peak detection at frequency below 1GHz.
     4. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and video bandwidth
        is 3 MHz for Peak detection at frequency above 1GHz.
     5. The resolution bandwidth of test receiver/spectrum analyzer is 1MHz and video bandwidth
         is 10Hz for Average detection at frequency above 1GHz.




Exclusive Certification Corp. Tel:886-2-2792-3366 Fax:886-2-2792-1100      Issued date: Nov. 02, 2005   24 of 56


                                                                    FCC Test Report: FE05080301-A



    Emission frequencies 1~40 GHz
    Test Mode: Normal, Channel 01, Transmit Rate: 54Mbps
    Test Date: Oct. 20, 2005     Temperature: 22℃       Humidity: 70%       Atmospheric pressure: 1020mmHg
                                Meter    Corrected                                                                 Ant
      Frequency     Ant-Pol                           Result@3m     Limit@3m       Margin                 Table
                               Reading     Factor                                              Remark              High
         (MHz)        H/V                              (dBuV/m)         (dBuV/m)     (dB)                 Deg.
                               (dBuV)       (dB)                                                                   (m)
       10362.10        H        42.43      15.79         58.22            68.3      -10.08      Peak      246      1.0
       15540.00        H         ---       17.13          ---             54.0        ---        Ave       ---      ---
       20720.00        H         ---       28.10          ---             54.0        ---        Ave       ---      ---
       25900.00        H         ---       31.67          ---             68.3        ---       Peak        --      --
       10358.89        V        44.23      14.92        -59.15            68.3       -9.15      Peak      350      1.0
       15540.00        V         ---       16.44          ---             54.0        ---        Ave       ---      ---
       20720.00        V         --        28.10          ---             54.0        ---        Ave       ---      ---
       25900.00        V         ---       31.67          ---             68.3        ---       Peak       ---      --
     Notes:
      1. Result = Meter Reading + Corrected Factor
     2. Corrected Factor = Antenna Factor + Cable Loss – Amplifier
      3. The resolution bandwidth of test receiver/spectrum analyzer is 120 kHz and video bandwidth
         is 300 kHz for Peak detection and Quasi-peak detection at frequency below 1GHz.
      4. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and video bandwidth
         is 3 MHz for Peak detection at frequency above 1GHz.
      5. The resolution bandwidth of test receiver/spectrum analyzer is 1MHz and video bandwidth
         is 10Hz for Average detection at frequency above 1GHz.
      6. The other emissions is too below to be measured.




Exclusive Certification Corp. Tel:886-2-2792-3366 Fax:886-2-2792-1100      Issued date: Nov. 02, 2005   25 of 56


                                                                    FCC Test Report: FE05080301-A


    Emission frequencies 1~40 GHz
    Test Mode: Normal, Channel 04, Transmit Rate: 54Mbps
    Test Date: Oct. 20, 2005     Temperature: 22℃       Humidity: 70%     Atmospheric pressure: 1020mmHg
                               Meter     Corrected                                                                Ant
      Frequency     Ant-Pol                          Result@3m      Limit@3m Margin                     Table
                              Reading     Factor                                             Remark               High
         (MHz)        H/V                              (dBuV/m)     (dBuV/m)        (dB)                 Deg.
                               (dBuV)       (dB)                                                                  (m)
       10481.13        H       42.79       16.08        58.87           68.3       -9.43       Peak      246      1.0
       15720.00        H         ---       16.70          ---           54.0         ---        Ave       ---     ---
       20960.00        H         ---       28.67          ---           54.0         ---        Ave       ---     ---
       26200.00        H         ---       32.07          ---           68.3         ---       Peak       --       --
       10481.17        V       44.78       15.28        60.06           68.3       -8.24       Peak      350      1.0
       15720.00        V         ---       16.04          ---           54.0         ---        Ave       ---     ---
       20960.00        V         ---       28.67          ---           54.0         ---        Ave       ---     ---
       26200.00        V         ---       32.07          ---           68.3         ---       Peak       ---      --
     Notes:
      1. Result = Meter Reading + Corrected Factor
     2. Corrected Factor = Antenna Factor + Cable Loss – Amplifier
      3. The resolution bandwidth of test receiver/spectrum analyzer is 120 kHz and video bandwidth
         is 300 kHz for Peak detection and Quasi-peak detection at frequency below 1GHz.
      4. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and video bandwidth
         is 3 MHz for Peak detection at frequency above 1GHz.
      5. The resolution bandwidth of test receiver/spectrum analyzer is 1MHz and video bandwidth
         is 10Hz for Average detection at frequency above 1GHz.




Exclusive Certification Corp. Tel:886-2-2792-3366 Fax:886-2-2792-1100     Issued date: Nov. 02, 2005   26 of 56


                                                                    FCC Test Report: FE05080301-A



    Emission frequencies 1~40 GHz
    Test Mode: Normal, Channel 05, Transmit Rate: 54Mbps
    Test Date: Oct. 20, 2005     Temperature: 22℃       Humidity: 70%     Atmospheric pressure: 1020mmHg
                               Meter     Corrected                                                                Ant
      Frequency     Ant-Pol                          Result@3m      Limit@3m Margin                     Table
                              Reading     Factor                                             Remark               High
         (MHz)        H/V                              (dBuV/m)     (dBuV/m)        (dB)                 Deg.
                               (dBuV)       (dB)                                                                  (m)
       10521.25        H       42.66       16.13        58.97           68.3       -9.33       Peak      246      1.0
       15780.00        H         ---       16.55          ---           54.0         ---        Ave       ---     ---
       21040.00        H         ---       28.90          ---           54.0         ---        Ave       ---     ---
       26300.00        H         ---       32.23          ---           68.3         ---       Peak       --       --
       10521.10        V       44.08       15.33        59.41           68.3       -8.89       Peak      350      1.0
       15780.00        V         ---       15.91          ---           54.0         ---        Ave       ---     ---
       21040.00        V         ---       28.90          ---           54.0         ---        Ave       ---     ---
       26300.00        V         ---       32.23          ---           68.3         ---       Peak       ---      --
     Notes:
     1. Result = Meter Reading + Corrected Factor
     2. Corrected Factor = Antenna Factor + Cable Loss – Amplifier
     3. The resolution bandwidth of test receiver/spectrum analyzer is 120 kHz and video bandwidth
        is 300 kHz for Peak detection and Quasi-peak detection at frequency below 1GHz.
     4. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and video bandwidth
        is 3 MHz for Peak detection at frequency above 1GHz.
     5. The resolution bandwidth of test receiver/spectrum analyzer is 1MHz and video bandwidth
        is 10Hz for Average detection at frequency above 1GHz.
     6. The other emissions is too below to be measured.




Exclusive Certification Corp. Tel:886-2-2792-3366 Fax:886-2-2792-1100     Issued date: Nov. 02, 2005   27 of 56


                                                                    FCC Test Report: FE05080301-A



    Emission frequencies 1~40 GHz
    Test Mode: Normal, Channel 08, Transmit Rate: 54Mbps
    Test Date: Oct. 20, 2005     Temperature: 22℃       Humidity: 70%     Atmospheric pressure: 1020mmHg
                               Meter     Corrected                                                                Ant
      Frequency     Ant-Pol                          Result@3m      Limit@3m Margin                     Table
                              Reading     Factor                                             Remark               High
         (MHz)        H/V                              (dBuV/m)     (dBuV/m)        (dB)                 Deg.
                               (dBuV)       (dB)                                                                  (m)
       10641.63        H       42.10       16.16        58.26           74.0      -15.74       Peak      246      1.0
       15960.00        H         ---       16.12          ---           54.0         ---        Ave       ---     ---
       21280.00        H         ---       29.75          ---           54.0         ---        Ave       ---     ---
      26600.00.        H         ---       32.52          ---           68.3         ---       Peak       --       --
       10641.63        V       42.80       15.36        58.16           74.0      -15.84       Peak      350      1.0
       15960.00        V         ---       15.51          ---           54.0         ---        Ave       ---     ---
       21280.00        V         ---       29.75          ---           54.0         ---        Ave       ---     ---
       26600.00        V         ---       32.52          ---           68.3         ---       Peak       ---      --
     Notes:
      1. Result = Meter Reading + Corrected Factor
     2. Corrected Factor = Antenna Factor + Cable Loss – Amplifier
      3. The resolution bandwidth of test receiver/spectrum analyzer is 120 kHz and video bandwidth
         is 300 kHz for Peak detection and Quasi-peak detection at frequency below 1GHz.
      4. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and video bandwidth
         is 3 MHz for Peak detection at frequency above 1GHz.
      5. The resolution bandwidth of test receiver/spectrum analyzer is 1MHz and video bandwidth
         is 10Hz for Average detection at frequency above 1GHz.
      6. The other emissions is too below to be measured




Exclusive Certification Corp. Tel:886-2-2792-3366 Fax:886-2-2792-1100     Issued date: Nov. 02, 2005   28 of 56


                                                                    FCC Test Report: FE05080301-A



     Test Model 2: POE mode
     Emission frequencies below 1 GHz        Channel 01
     Test Date: Oct. 20, 2005     Temperature: 22℃      Humidity: 70%      Atmospheric pressure: 1020mmHg
                                Meter    Corrected                                                                Ant
      Frequency     Ant-Pol                          Result@3m      Limit@3m Margin                     Table
                              Reading     Factor                                             Remark               High
         (MHz)        H/V                              (dBuV/m)     (dBuV/m)        (dB)                 Deg.
                              (dBuV)        (dB)                                                                  (m)
        124.60         H        47.72     -16.01        31.71           43.5      -11.79       Peak       75      1.1
        136.98         H        51.16     -14.69        36.347          43.5       -7.03       Peak       75      1.1
        141.65         H        47.44     -14.46        32.98           43.5      -10.52       Peak       75      1.1
        268.43         H        53.08     -12.06        41.02           46.0       -4.98        Q.P        0      1.1
        325.00         H        54.48     -10.88        43.60           46.0       -2.40        Q.P       20      1.1
        348.30         H        54.02     -10.47        43.55           46.0       -2.45        Q.P      100      1.1
        449.80         H        46.72      -8.81        37.91           46.0       -8.09       Peak        0      1.1
        997.90         H        45.85       2.78        48.63           54.0       -5.37        Q.P        0      1.1
         51.73         V        52.26     -15.88        36.38           40.0       -3.62        Q.P       40      1.0
        138.63         V        47.82     -14.57        33.25           43.5      -10.25       Peak        0      1.0
        249.73         V        56.98     -13.36        43.62           46.0       -2.38        Q.P      200      1.0
        268.98         V        55.50     -12.02        43.48           46.0       -2.52        Q.P      200      1.0
        348.30         V        53.50     -10.47        43.03           46.0       -2.97        Q.P      215      1.0
        400.80         V        49.75      -8.87        40.88           46.0       -5.12        Q.P       30      1.0
        498.80         V        50.90      -7.05        43.85           46.0       -2.15        Q.P       30      1.0
        747.30         V        44.67      -1.52        43.15           46.0       -2.85        Q.P        0      1.0
     Notes:
     1. Result = Meter Reading + Corrected Factor
     2. Corrected Factor = Antenna Factor + Cable Loss – Amplifier
     3. The resolution bandwidth of test receiver/spectrum analyzer is 120 kHz and video bandwidth
         is 300 kHz for Peak detection and Quasi-peak detection at frequency below 1GHz.
     4. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and video bandwidth
        is 3 MHz for Peak detection at frequency above 1GHz.
     5. The resolution bandwidth of test receiver/spectrum analyzer is 1MHz and video bandwidth
         is 10Hz for Average detection at frequency above 1GHz.
    6. The other emissions is too below to be measured.




Exclusive Certification Corp. Tel:886-2-2792-3366 Fax:886-2-2792-1100     Issued date: Nov. 02, 2005   29 of 56


                                                                    FCC Test Report: FE05080301-A



     Test Model 2: PoE mode
     Emission frequencies 1~40 GHz
     Test Mode: Normal, Channel 01, Transmit Rate: 54Mbps
     Test Date: Oct. 20, 2005     Temperature: 22℃      Humidity: 70%       Atmospheric pressure: 1020mmHg
                                Meter    Corrected                                                                 Ant
      Frequency     Ant-Pol                           Result@3m     Limit@3m       Margin                 Table
                              Reading      Factor                                              Remark              High
         (MHz)        H/V                              (dBuV/m)         (dBuV/m)     (dB)                 Deg.
                              (dBuV)        (dB)                                                                   (m)
       10362.10        H        42.51      15.79         58.30            68.3      -10.00      Peak      246      1.0
       15540.00        H         ---       17.13          ---             54.0        ---        Ave       ---      ---
       20720.00        H         ---       28.10          ---             54.0        ---        Ave       ---      ---
       25900.00        H         ---       31.67          ---             68.3        ---       Peak        --      --
       10358.89        V        44.50      14.92         59.42            68.3       -8.88      Peak      350      1.0
       15540.00        V         ---       16.44          ---             54.0        ---        Ave       ---      ---
       20720.00        V         --        28.10          ---             54.0        ---        Ave       ---      ---
       25900.00        V         ---       31.67          ---             68.3        ---       Peak       ---      --
     Notes:
      1. Result = Meter Reading + Corrected Factor
     2. Corrected Factor = Antenna Factor + Cable Loss – Amplifier
      3. The resolution bandwidth of test receiver/spectrum analyzer is 120 kHz and video bandwidth
         is 300 kHz for Peak detection and Quasi-peak detection at frequency below 1GHz.
      4. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and video bandwidth
         is 3 MHz for Peak detection at frequency above 1GHz.
      5. The resolution bandwidth of test receiver/spectrum analyzer is 1MHz and video bandwidth
         is 10Hz for Average detection at frequency above 1GHz.
      6. The other emissions is too below to be measured.




Exclusive Certification Corp. Tel:886-2-2792-3366 Fax:886-2-2792-1100      Issued date: Nov. 02, 2005   30 of 56



Document Created: 2005-12-01 18:21:35
Document Modified: 2005-12-01 18:21:35

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC