TEST REPORT

FCC ID: PWO8012SM

Test Report

Download: PDF
FCCID_750266

849 NW STATE ROAD 45 NEWBERRY, FL 32669 USA PH: 888.472.2424 OR 352.472.5500 FAX: 352.472.2030 EMAIL: TEI@TIMCOENGR.COM HTTP://WWW.TIMCOENGR.COM FCC PART 22H & 24E CLASS II PERMISSIVE CHANGE TEST REPORT APPLICANT Wilson Electronics, Inc. ADDRESS 3301 E. Deseret Drive St. George, Utah 84790 USA FCC ID PWO8012SM MODEL NUMBER 271245 PRODUCT DESCRIPTION Mobile Wireless Cellular / PCS SmartTech Amplifier DATE SAMPLE October 11, 2006 RECEIVED DATE TESTED October 19, 2006 Tested By Nam Nguyen Approved By Mario de Aranzeta TEST RESULTS PASS FAIL THE ATTACHED REPORT SHALL NOT BE REPRODUCED EXCEPT IN FULL WITHOUT THE WRITTEN APPROVAL OF TIMCO ENGINEERING, INC. Certificate # 0955-01

TABLE OF CONTENTS COMPLIANCE STATEMENT ....................................................................................... 3 REPORT SUMMARY................................................................................................... 4 TEST ENVIRONMENT AND TEST SETUP ................................................................... 4 DEVICE UNDER TEST INFORMATION ....................................................................... 5 EQUIPMENT LIST ...................................................................................................... 6 RF POWER OUTPUT .................................................................................................. 7 INPUT/OUTPUT MODULATED AMPLITUDE COMPARISON AND BAND-EDGES COMPLIANCE............................................................................................................ 9 INTERMODULATION PRODUCT SPURIOUS EMISSIONS .......................................... 14 SPURIOUS EMISSIONS AT ANTENNA TERMINALS .................................................. 23 FIELD STRENGTH OF SPURIOUS EMISSIONS......................................................... 26 APPLICANT: WILSON ELECTRONICS, INC. FCC ID: PWO8012SM REPORT #: W\WILSON_PWO\78AUT6\78AUT6TestReport.doc Page 2 of 28

COMPLIANCE STATEMENT Certificate # 0955-01 This equipment has been tested in accordance with the standards identified in this test report. To the best of my knowledge and belief, these tests were performed using the measurement procedures described in this report and demonstrate that the equipment complies with the appropriate standards. No modifications were made to the equipment during testing in order to demonstrate compliance with these standards. I attest that the necessary measurements were made, under my supervision, at TIMCO ENGINEERING, INC. located at 849 N.W. State Road 45, Newberry, Florida 32669. Authorized Signatory Name: Mario de Aranzeta Signature: On file Function: Engineer Date: 11/10/2006 Tester name: Nam Nguyen Signature: On file Date: 11/10/2006 APPLICANT: WILSON ELECTRONICS, INC. FCC ID: PWO8012SM REPORT #: W\WILSON_PWO\78AUT6\78AUT6TestReport.doc Page 3 of 28

REPORT SUMMARY Disclaimer The test results relate only to the items tested. Report Purpose To demonstrate the modified unit continues to comply with FCC Part 22 and Part 24 requirements Applicable Rule Pt 22H, Pt 24 E, Pt 15.109, ANSI C63.4: 2003 Part(s) Related Test Report 2851BUT6TestReport for digital interface testing TEST ENVIRONMENT AND TEST SETUP Test Facilities All required tests were performed by Timco Engineering Inc. that is located at 849 NW State Road 45 Newberry, FL 32669 Timco test facilities accreditation is on file with regulatory agencies. Test Conditions Temperature: 26ºC Relative Humidity: 50% Deviation to the rules There was no deviation from the test standards. Modification to the No modification was made to the DUT. DUT Test Exercise (e.g. The DUT was placed in continuous transmit mode of software description, operation. test signal, etc.) Supporting Test Manufacturer: Agilent Equipment Description: Dual-mode baseband generator (arbitrary waveform and real time I/Q) 250 kHz to 6 GHz Model Number: E4438C Cal Date: 01/31/06 Cal Due Date: 01/31/08 APPLICANT: WILSON ELECTRONICS, INC. FCC ID: PWO8012SM REPORT #: W\WILSON_PWO\78AUT6\78AUT6TestReport.doc Page 4 of 28

DEVICE UNDER TEST INFORMATION Manufactured by Willson Electronics DUT Description Mobile wireless, cell phone amplifier FCC ID PWO8012SW Model Name 271245 Operating Frequency Pt 22H Uplink 824 – 849 MHz Pt 22H Downlink 869 – 894 MHz Pt 24E Uplink 1850 – 1910 MHz Pt 24E Downlink 1930 – 1990 MHz Emission Designators 300KGXW (GSM850), 300KGXW (GSM 1900) 1M28F9W (CDMA) Modulation(s) F9W, GXW (GSM, EDGE), G7W, F1D User Power Range & There are NO user power controls Control Test Item Pre-Production Type of Equipment Fixed and Mobile Antenna Connector N APPLICANT: WILSON ELECTRONICS, INC. FCC ID: PWO8012SM REPORT #: W\WILSON_PWO\78AUT6\78AUT6TestReport.doc Page 5 of 28

EQUIPMENT LIST Device Manufacturer Model Serial Cal/Char Due Date Number Date 3/10-Meter TEI N/A N/A Listed 3/26/07 OATS 3/27/04 3-Meter TEI N/A N/A Listed 1/10/09 OATS 1/11/06 Biconnical Eaton 94455-1 1057 CAL 12/12/07 Antenna 12/12/05 Biconnical Eaton 94455-1 1096 CAL 8/17/08 Antenna 8/17/06 Biconnical Electro- BIA-25 1171 CAL 4/29/07 Antenna Metrics 4/29/05 Blue Tower HP 85650A 2811A01279 CAL 4/13/07 Quasi-Peak 4/13/05 Adapter Blue Tower HP 85685A 2926A00983 CAL 9/5/07 RF 9/5/05 Preselector Blue Tower HP 8568B 2928A04729 CAL 4/13/07 Spectrum 2848A18049 4/13/05 Analyzer LISN Electro- ANS-25/2 2604 CAL 8/27/08 Metrics 8/27/06 LISN Electro- EM-7820 2682 CAL 4/28/07 Metrics 4/28/05 Log-Periodic Eaton 96005 1243 CAL 12/14/07 Antenna 12/14/05 Passive Loop EMC Test EMCO 9706-1211 CHAR 7/10/08 Antenna Systems 6512 7/10/06 APPLICANT: WILSON ELECTRONICS, INC. FCC ID: PWO8012SM REPORT #: W\WILSON_PWO\78AUT6\78AUT6TestReport.doc Page 6 of 28

RF POWER OUTPUT Rule Part(s) No.: Pt 2.1046(a) Requirements: Method of Measurement: RF power is measured by connecting a 50 ohm, resistive wattmeter to the RF output connector. With a nominal voltage of 5 VDC using the AC/DC switched mode power supply specified with this device, and the amplifier properly adjusted the RF output measures: RF Output Power Test Setup Diagram Vector Signal In Out 30dB Generator DUT Attenuator Power Supply 50 ohm Power Meter Test Data: 800 MHz band Uplink Frequency Power Output MHz Modulation Watts 825.25 CDMA 1.02 836.5 CDMA 1.34 847.75 CDMA 0.64 824.28 GSM 0.89 836.5 GSM 1.11 848.72 GSM 0.51 824.28 EDGE 0.82 836.5 EDGE 1.05 848.72 EDGE 0.52 1900 MHz band uplink Frequency Power Output MHz Modulation Watts 1851.25 CDMA 0.80 1880 CDMA 1.06 1908.75 CDMA 0.40 1850.28 GSM 0.60 1880 GSM 0.89 1909.72 GSM 0.41 1850.28 EDGE 1.00 1880 EDGE 1.05 1909.72 EDGE 0.40 The worst-case power output was found with the amplifier modulated by CDMA. APPLICANT: WILSON ELECTRONICS, INC. FCC ID: PWO8012SM REPORT #: W\WILSON_PWO\78AUT6\78AUT6TestReport.doc Page 7 of 28

Test Data: 800 MHz band downlink Frequency Power Output MHz Modulation Watts 870.25 CDMA .009 881.5 CDMA .008 892.75 CDMA .010 869.28 GSM .010 881.5 GSM .010 893.72 GSM .012 869.28 EDGE .010 881.5 EDGE .009 893.72 EDGE .012 1900 MHz band downlink Frequency Power Output MHz Modulation Watts 1931.25 CDMA .007 1960 CDMA .010 1988.75 CDMA .009 1930.28 GSM .006 1960 GSM .010 1989.72 GSM .009 1930.28 EDGE .006 1960 EDGE .009 1989.72 EDGE .008 The worst-case power output was found with the amplifier modulated by CDMA. APPLICANT: WILSON ELECTRONICS, INC. FCC ID: PWO8012SM REPORT #: W\WILSON_PWO\78AUT6\78AUT6TestReport.doc Page 8 of 28

INPUT/OUTPUT MODULATED AMPLITUDE COMPARISON AND BAND- EDGES COMPLIANCE Rule Parts No.: Pt 2.1049, Pt 2.1051, Pt 24.238, Pt 22 Requirements: The power of any emission outside of the authorized operating frequency ranges must be attenuated below the transmitting power (P) by a factor of at least 43 + 10 log(P) dB. Method of Measurement: On the following plot, the reference level was calibrated using a resolution bandwidth wider than the emission bandwidth. First the gain was measured for the maximum output power. Then for each frequency and type of modulation, an attenuation equals to the gain of the amplifier was added on the measurement side of the amplifier, as to overlay the input versus output modulated envelope. Test Setup Diagram Vector Signal Power generator Supply High Agilent 30dB Pass Attenuator Filter Decoupling In-Out Network Device under Test ESIB 40 EMI Test Receiver Power Meter HP Supporting Equipment: Manufacturer Description Model Cal Due Number Cal Date Date Agilent Dual-mode baseband generator E4438C 01/31/06 01/31/08 (arbitrary waveform and real time I/Q) 250 kHz to 6 GHz Test Data: The data presented below is for the worst-case modulation found. APPLICANT: WILSON ELECTRONICS, INC. FCC ID: PWO8012SM REPORT #: W\WILSON_PWO\78AUT6\78AUT6TestReport.doc Page 9 of 28

CDMA Band-edge Amplitude level at Limit Channel (MHz) Frequency the band-edge (dBm) (MHz) (dBm) 1851.25 1850 -16.13 -13 1908.75 1910 -14.02 -13 825.25 824 -17.34 -13 847.75 849 -14.11 -13 The reference level on the following plots was calibrated using a 3MHz RBW=VBW. Figure 1: CDMA modulation - up link 1900MHz band – In vs. Out 1851.25MHz APPLICANT: WILSON ELECTRONICS, INC. FCC ID: PWO8012SM REPORT #: W\WILSON_PWO\78AUT6\78AUT6TestReport.doc Page 10 of 28

Figure 2: CDMA modulation - up link 1900MHz band – In vs. Out 1908.75MHz APPLICANT: WILSON ELECTRONICS, INC. FCC ID: PWO8012SM REPORT #: W\WILSON_PWO\78AUT6\78AUT6TestReport.doc Page 11 of 28

Figure 3: CDMA modulation - up link 800MHz band – In vs. Out 825.25MHz APPLICANT: WILSON ELECTRONICS, INC. FCC ID: PWO8012SM REPORT #: W\WILSON_PWO\78AUT6\78AUT6TestReport.doc Page 12 of 28

Figure 4: CDMA modulation - up link 800MHz band – In vs. Out 847.75MHz APPLICANT: WILSON ELECTRONICS, INC. FCC ID: PWO8012SM REPORT #: W\WILSON_PWO\78AUT6\78AUT6TestReport.doc Page 13 of 28

INTERMODULATION PRODUCT SPURIOUS EMISSIONS Rule Parts No.: Pt 2.1051 Requirements: Emissions must be 43 + 10 log (Po) dB below the mean power output of the transmitter or below the –13dBm Method of Measurement: The procedure used was TIA/EIA-603 STANDARD. The spectrum was scanned from 9kHz to at least the tenth harmonic of the fundamental using a HP model 8566B spectrum analyzer. All the modulation type (CDMA, GSM, EDGE, and FM) were tested using the two tone test method. A CW signal was use instead of GSM, EDGE, and F1D modulations. EDGE and GSM provided the same test results and only GSM data are presented in this report. The input power to the amplifier was set at maximum drive level by combining the two tones. The two tones were chosen in such a way (1)the third order intermodulation product frequencies are located within the pass band of the EUT and (2) they produce the worst-case emissions out of band. Setup Diagram (1)vector Signal Power Supply High 30dB Pass (2)Vector Combine Attenuat Signal Filter In or Out Decoupli Band ng Device Under HP 8566B Pass Network Spectrum Filter Analyzer Power Meter HP The following specific test equipments were used: Manufacturer Description M/N Cal Date Cal Due Date Agilent Dual-mode baseband generator E4438C 01/31/06 01/31/08 (arbitrary waveform and real time I/Q) 250 kHz to 6 GHz APPLICANT: WILSON ELECTRONICS, INC. FCC ID: PWO8012SM REPORT #: W\WILSON_PWO\78AUT6\78AUT6TestReport.doc Page 14 of 28

Emission out Tuned of band Emission frequency frequency level Limit (MHz) (MHz) (dBm) (dBm) 1850.28 1847.07 -14.87 -13 1909.72 1912.23 -17.16 -13 1930.28 1929.38 -17.41 -13 1989.72 1990.99 -17.38 -13 Figure 5: Intermodulation 2 tones spurious emissions Up link (1850 MHz) APPLICANT: WILSON ELECTRONICS, INC. FCC ID: PWO8012SM REPORT #: W\WILSON_PWO\78AUT6\78AUT6TestReport.doc Page 15 of 28

Figure 6: Intermodulation 2 tones spurious emissions Up link (1910 MHz) APPLICANT: WILSON ELECTRONICS, INC. FCC ID: PWO8012SM REPORT #: W\WILSON_PWO\78AUT6\78AUT6TestReport.doc Page 16 of 28

Figure 7: Intermodulation 2 tones spurious emissions Down link (1930 MHz) APPLICANT: WILSON ELECTRONICS, INC. FCC ID: PWO8012SM REPORT #: W\WILSON_PWO\78AUT6\78AUT6TestReport.doc Page 17 of 28

Figure 8: Intermodulation 2 tones spurious emissions Down link (1990 MHz) APPLICANT: WILSON ELECTRONICS, INC. FCC ID: PWO8012SM REPORT #: W\WILSON_PWO\78AUT6\78AUT6TestReport.doc Page 18 of 28

Emission out Tuned of band Emission Frequency frequency level Limit (MHz) (MHz) (dBm) (dBm) 824.28 821.12 -15.25 -13 848.72 851.96 -16.63 -13 869.28 866.37 -18.88 -13 893.72 896.42 -18.82 -13 Figure 9: Intermodulation 2 tones spurious emissions Up link (824 MHz) APPLICANT: WILSON ELECTRONICS, INC. FCC ID: PWO8012SM REPORT #: W\WILSON_PWO\78AUT6\78AUT6TestReport.doc Page 19 of 28

Figure 10: Intermodulation 2 tones spurious emissions Up link (849 MHz) APPLICANT: WILSON ELECTRONICS, INC. FCC ID: PWO8012SM REPORT #: W\WILSON_PWO\78AUT6\78AUT6TestReport.doc Page 20 of 28

Figure 11: Intermodulation 2 tones spurious emissions Down link (869 MHz) APPLICANT: WILSON ELECTRONICS, INC. FCC ID: PWO8012SM REPORT #: W\WILSON_PWO\78AUT6\78AUT6TestReport.doc Page 21 of 28

Figure 12: Intermodulation 2 tones spurious emissions Down link (894 MHz) APPLICANT: WILSON ELECTRONICS, INC. FCC ID: PWO8012SM REPORT #: W\WILSON_PWO\78AUT6\78AUT6TestReport.doc Page 22 of 28

SPURIOUS EMISSIONS AT ANTENNA TERMINALS Rule Parts No.: Pt 2.1051 Requirements: Emissions must be 43 +10log(Po) dB below the mean power output of the transmitter: Up link: 43 + 10log(1.00) = 43 dBc Down link: 43 + 10log(0.02) = 26 dBc Method of Measurement: The procedure used was TIA/EIA-603 STANDARD. The spectrum was scanned from 9kHz to at least the tenth harmonic of the fundamental using a HP model 8566B spectrum analyzer. Data on the following page shows the level of conducted spurious responses. For analog modulation, the carrier was modulated 100% using a 2500 Hz tone. For digital modulation, the carrier is modulated to its maximum extent. The spectrum was scanned from 9kHz to at least the 10th harmonic of the fundamental. The measurements were made in accordance with standard TIA/EIA-603. All the modulation types (CDMA, GSM, EDGE, and FM) were tested at a low, mid, and high channel in each band. CW (FM) was used in place of GSM and EDGE modulations. The maximum input power was set for each test. Conducted Spurious Emissions Test Setup Diagram Vector Signal Power High generator Supply Pass Agilent E4438C 30dB Filter Attenuator Decoupling In Out Network DUT ESIB 40 EMI TEST Receiver Power Meter HP The following test equipment was used: Manufacturer Description Model Cal Due Number Cal Date Date Agilent Dual-mode baseband generator E4438C 01/31/06 01/31/08 (arbitrary waveform and real time I/Q) 250 kHz to 6 GHz APPLICANT: WILSON ELECTRONICS, INC. FCC ID: PWO8012SM REPORT #: W\WILSON_PWO\78AUT6\78AUT6TestReport.doc Page 23 of 28

Test Data: 1900 MHz Up Link: Emission dB below Emission dB below Emission dB below Frequency Carrier Frequency Carrier Frequency Carrier MHz (dBc) MHz (dBc) MHz (dBc) 1850.28 0 1880.00 0 1909.72 0 3700.56 86 3760.00 92.2 3819.44 88.5 5550.84 83.6 5640.00 87.7 5729.16 86.4 7401.12 83.4 7520.00 90.2 7638.88 87.5 9251.40 84.8 9400.00 91.2 9548.60 87.2 11101.68 84.8 11280.00 89.6 11458.32 87.3 12951.96 >62.0 13160.00 >62.0 13368.04 >62.0 14802.24 >62.0 15040.00 >62.0 15277.76 >62.0 16652.52 >62.0 16920.00 >62.0 17187.48 >62.0 18502.80 >62.0 18800.00 >62.0 19097.20 >62.0 1900 MHz Down Link: Emission dB Below Emission dB Below Emission dB Below Frequency Carrier Frequency Carrier Frequency Carrier MHz (dBc) MHz (dBc) MHz (dBc) 1930.28 0 1960.00 0 1989.72 0 3860.56 41.5 3920.00 46.1 3979.44 50.9 5790.84 60 5880.00 64.8 5969.16 68.2 7721.12 70.6 7840.00 72.6 7958.88 71.2 9651.40 70.2 9800.00 73.9 9948.60 71.5 11581.68 69.6 11760.00 70.9 11938.32 71.4 13511.96 >60.0 13720.00 >60.0 13928.04 >60.0 15442.24 >60.0 15680.00 >60.0 15917.76 >60.0 17372.52 >60.0 17640.00 >60.0 17907.48 >60.0 19302.80 >60.0 19600.00 >60.0 19897.20 >60.0 APPLICANT: WILSON ELECTRONICS, INC. FCC ID: PWO8012SM REPORT #: W\WILSON_PWO\78AUT6\78AUT6TestReport.doc Page 24 of 28

[Continued] 800 MHz Up Link: Emission dB Below Emission dB Below Emission dB Below Frequency Carrier Frequency Carrier Frequency Carrier MHz (dBc) MHz (dBc) MHz (dBc) 824.03 0 836.50 0 848.97 0 1648.06 63.7 1673.00 80.8 1697.94 70.3 2472.09 92.2 2509.50 92.1 2546.91 89.4 3296.12 87.9 3346.00 92.5 3395.88 89.1 4120.15 94.5 4182.50 93 4244.85 89.3 4944.18 94.3 5019.00 92.1 5093.82 88 5768.21 89.4 5855.50 89.6 5942.79 86.4 6592.24 >58.0 6692.00 >58.0 6791.76 >58.0 7416.27 >58.0 7528.50 >58.0 7640.73 >58.0 8240.30 >58.0 8365.00 >58.0 8489.70 >58.0 800 MHz Down Link: Emission dB Below Emission dB Below Emission dB Below Frequency Carrier Frequency Carrier Frequency Carrier MHz (dBc) MHz (dBc) MHz (dBc) 869.03 0 881.50 0 893.97 0 1738.06 52 1763.00 55.6 1787.94 56.7 2607.09 40.7 2644.50 29.1 2681.91 37.5 3476.12 65.1 3526.00 68.4 3575.88 67 4345.15 73.8 4407.50 61.8 4469.85 59.8 5214.18 72.7 5289.00 68.8 5363.82 73.6 6083.21 72.9 6170.50 72.5 6257.79 72 6952.24 72.6 7052.00 68.4 7151.76 73.6 7821.27 72 7933.50 71.8 8045.73 71.9 8690.30 72.8 8815.00 76.2 8939.70 73.5 APPLICANT: WILSON ELECTRONICS, INC. FCC ID: PWO8012SM REPORT #: W\WILSON_PWO\78AUT6\78AUT6TestReport.doc Page 25 of 28

FIELD STRENGTH OF SPURIOUS EMISSIONS Rule Parts No.: Pt 2.1053 Requirements: Emissions must be 43 +10log(Po) dB below the mean power output of the amplifier: Up link: 43 + 10log(1.12) = 43.5 dB Down link: 43 + 10log(0.02) = 26.0 dB CW signal was used for this test. METHOD OF MEASUREMENTS: The spectrum was scanned from 30 MHz to at least the tenth harmonic of the fundamental. The CW signal was used to perform this test. This test was conducted per TIA/EIA STANDARD 603 using the substitution method. Radiated Spurious Emissions Test Setup Diagram Signal Generator DUT Spectrum 3 meters Analyzer Equipment placed 80 cm above ground on a rotating table platform. Test Data: The following tabulated data shows the result of the radiated field strength emissions test. The worst-case spurious emissions data are reported. Up link: Emission Ant. Corrected Coax Substitution dB Below Frequency Polarity EUT Signal Loss Antenna Carrier MHz V/H Reading (dB) (dBd) (dBc) 1880.00 0 3760.00 H -48.60 1.43 7.55 72.98 5640.00 V -54.70 1.75 8.55 78.4 7520.00 V -58.80 2.06 8.69 82.67 9400.00 V -53.60 2.38 9.53 76.95 11280.00 V -55.10 2.70 8.35 79.94 13160.00 V -44.40 3.01 9.94 67.97 15040.00 H -43.90 3.33 10.94 66.79 16920.00 V/H * * * * 18800.00 V/H * * * * APPLICANT: WILSON ELECTRONICS, INC. FCC ID: PWO8012SM REPORT #: W\WILSON_PWO\78AUT6\78AUT6TestReport.doc Page 26 of 28

*No other emissions were found up to the 10th harmonics - NOISE FLOOR Down link: Emission Ant. Corrected Coax Substitution dB Below Frequency Polarity EUT Signal Loss Antenna Carrier MHz V/H Reading (dB) (dBd) (dBc) 1960.00 0 3920.00 H -41.70 1.46 7.55 45.61 5880.00 V -51.90 1.79 8.88 54.81 7840.00 H -53.80 2.12 7.80 58.12 9800.00 H -45.40 2.45 9.33 48.52 11760.00 V -47.40 2.78 8.33 51.85 13720.00 H -43.50 3.11 9.51 47.10 15680.00 V/H * * * * 17640.00 V/H * * * * 19600.00 V/H * * * * *No other emissions were found up to the 10th harmonics - NOISE FLOOR Up link: Emission Ant. Corrected Coax Substitution dB Below Frequency Polarity EUT Signal Loss Antenna Carrier MHz V/H Reading (dB) (dBd) (dBc) 836.50 0 1673.00 H -60.90 1.08 5.05 87.82 2509.50 H -53.70 1.22 6.86 78.96 3346.00 V -59.40 1.36 7.46 84.20 4182.50 V -57.90 1.50 7.84 82.46 5019.00 H -55.90 1.64 7.77 80.67 5855.50 H -52.20 1.78 8.85 76.03 6692.00 H -55.30 1.92 8.21 79.91 7528.50 0 * * * * 8365.00 0 * * * * *No other emissions were found up to the 10th harmonics - NOISE FLOOR APPLICANT: WILSON ELECTRONICS, INC. FCC ID: PWO8012SM REPORT #: W\WILSON_PWO\78AUT6\78AUT6TestReport.doc Page 27 of 28

Down link: Emission Ant. Corrected Coax Substitution dB Below Frequency Polarity EUT Signal Loss Antenna Carrier MHz V/H Reading (dB) (dBd) (dBc) 881.50 0 1763.00 H -53.60 1.09 5.11 60.56 2644.50 V -59.90 1.24 6.97 65.15 3526.00 V -59.40 1.39 7.55 64.21 4407.50 V -55.60 1.54 8.20 59.91 5289.00 H -53.70 1.69 8.10 58.26 6170.50 V -57.50 1.84 8.95 61.36 7052.00 0 * * * * 7933.50 0 * * * * 8815.00 0 * * * * *No other emissions were found up to the 10th harmonics - NOISE FLOOR APPLICANT: WILSON ELECTRONICS, INC. FCC ID: PWO8012SM REPORT #: W\WILSON_PWO\78AUT6\78AUT6TestReport.doc Page 28 of 28


Document Created: 2006-11-10 11:19:22
Document Modified: 2006-11-10 11:19:22
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC