Users Manual Revised

FCC ID: PWO460035

Users Manual

Download: PDF
FCCID_3496992

A WILSON ELECTRONICS BRAND DRIVE SLEEK Vehicle Signal Booster Kit User Manual NEED HELP? support.weboost.com 866.294.1660

______ Index Package Contents 1 STEP 1: Mount Outside Antenna 2 STEP 2: Route & Connect Booster 3 STEP 3: Route Cable To Front Of Vehicle 5 STEP 4: Connect System To Power 6 STEP 5: Insert Phone Into Cradle 7 Light Patterns 8 Troubleshooting 9 Safety Guidelines 11 Specifications 12 Warranty 14

________ Package Contents Sleek Outside Signal Power Magnetic Cradle Antenna Booster Supply Vent Mount (for cradle) 1 DRIVE SLEEK CELL PHONE SIGNAL BOOSTER

______ Step 1: Mount Outside Magnetic Antenna Identify a location on the top of your vehicle that is: • Near the center of the roof • At least 12 inches away from any other antennas • At least 6 inches away from any windows (including sunroofs) Clean the surface where you will place the outside antenna. Mount the outside antenna. 6 in. away from windows (including sunroofs) NOTE: For roofs that are not metallic, use the included metal disk by peeling away the adhesive cover and sticking on the clean surface. WORKS WITH ALL VEHICLES 2 CELL PHONE SIGNAL BOOSTER DRIVE SLEEK

______ Step 2: Route & Connect Booster Route the cable into the vehicle. See examples below. NOTE: The cable is strong enough that it may be shut in most vehicle doors without damaging the cable. Car/Sedan: Cable routed into rear side door. SUV/Van/Hatchback: Cable routed into top of hatchback door. Truck: Cable routed into side door. 3 DRIVE SLEEK CELL PHONE SIGNAL BOOSTER

______ (STEP 2 cont.) Connect the cable from the outside antenna to the booster port labeled ANTENNA by simply pressing the connector in until you hear a “click”. booster cable from outside antenna ANTENNA 4 CELL PHONE SIGNAL BOOSTER DRIVE SLEEK

______ Step 3: Route Cable To Front Of Vehicle We recommend routing the 15ft. fixed cable from the booster, under mats and between seats up to the front of the vehicle where the cradle will be located. to front of vehicle Connect booster cable to cable from cradle. snap-in connectors cradle 5 DRIVE SLEEK CELL PHONE SIGNAL BOOSTER

______ Step 4: Connect System To Power Connect the power to the 12V CLA port on your vehicle and route power cable back to the booster. NOTE: We recommend routing with the same path as the cable going up to the cradle (under mats and between seats). connect power supply to 12V port connect to booster Connect power cable to booster port labeled . NOTE: The booster will be on whenever there is power from the 12V CLA port. If your vehicle always has power going to this port, you may want to ANTENNA unplug this when you’re not driving so the booster does not drain your battery. 6 CELL PHONE SIGNAL BOOSTER DRIVE SLEEK

______ Step 5: Insert Your Phone Into Cradle Make sure you have plenty of slack in the cable going up to the cradle (velcro straps included to manage excess cable). Insert your phone into cradle and watch your signal increase! insert phone into cradle to boost signal cradle extends magnetic vent mount NOTE: Magnetic vent mount included to mount the cradle to your dash. 7 DRIVE SLEEK CELL PHONE SIGNAL BOOSTER

______ Light Patterns Solid White This indicates that your booster is functioning properly and at maximum gain. Light Off Needs power. NEED HELP? support.weboost.com 866.294.1660 8 CELL PHONE SIGNAL BOOSTER DRIVE SLEEK

______ Troubleshooting FIXING BLINKING LIGHT ISSUES 1 Make sure all connections are tight. 2 Increase the distance between the outside antenna and cradle, by moving them horizontally and/or vertically farther apart until the light change to green. Remember to keep the antenna at least 6 inches from any window or sunroof. 3 Reset system by disconnecting and reconnecting the power supply. 4 If you are having any difficulties while testing or installing your booster, contact our weBoost Customer Support team for assistance (866.294.1660). FREQUENTLY ASKED QUESTIONS What hours can I contact customer support? Customer Support can be reached monday thru friday by calling 866.294.1660, or through our support site at support.weboost.com. Why do I need to create distance between the booster and the antenna? Antennas connected to a booster create spheres of signal. When these spheres overlap, a condition called oscillation occurs. Oscillation can be thought of as noise, which causes the booster to shut down to prevent damage. The best way to keep these spheres of signal from overlapping is to maximize separation between the Booster and Antenna. NEED HELP? support.weboost.com 866.294.1660 9 DRIVE SLEEK CELL PHONE SIGNAL BOOSTER

______ Antenna Kit Options MOBILE 4G Trucker Antenna w/13.5’ RG58 Kit 311112-17410 311119 800/1900 NMO Antenna 311133 10’ RG174 Cable Outside Antenna Options 4G Trucker Antenna w/15’ RG58 Kit 314203-17410 304415 800/900/1900 NMO Antenna 304414 10’ RG174 Cable Mini-Mag Marine Antenna w/10’ RG58 301126 w/ 12.5 RG174 cable - SMA 311130-5810 NMO Antenna w/RG58 301113 w/ 12.5 RG174 cable - FME Marine Antenna w/20’ RG58 12” Mag Mount w/12.5’ RG58 304420 301103 Kit 311104-5810 Glass Mount w/14’ RG58 800/1900 NMO Antenna 311125 311128 311102 10’ RG58 Cable 314202 Kit 311112-5810 311703 NMO Antenna w/RG174 800/1900 NMO Antenna Trucker Antenna w/10.5’ RG58 10’ RG58 Cable 311101 Kit 311104-17410 Kit 314203-5810 311701 800/1900 NMO Antenna 800/900/1900 NMO Antenna 10’ RG174 Cable 10’ RG58 Cable 10 CELL PHONE SIGNAL BOOSTER DRIVE SLEEK

______ Safety Guidelines Use only the power supply provided in this package. Use of a non-weBoost product may damage your equipment. Connecting the Signal Booster directly to the cell phone with use of an adapter will damage the cell phone. Use only the power supply provided in this package. Use of a non-weBoost product may damage your equipment. The Signal Booster unit is designed for use in an indoor, temperature-controlled environment (less than 150 degrees Fahrenheit). It is not intended for use in attics or similar locations subject to temperatures in excess of that range. The outside antenna must be installed no higher than 10 meters (32’9”) above ground. Any antenna used with this device must be located at least 8 inches from all persons. FCC requires to never use the cell phone in the cradle next to your ear. This is a CONSUMER device. BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider’s consent. Most wireless providers consent to the use of signal boosters. Some providers may not consent to the use of this device on their network. If you are unsure, contact your provider. In Canada, BEFORE USE you must meet all requirements set out in ISED CPC-2-1-05. You MUST operate this device with approved antennas and cables as specified by the manufacturer. Antennas MUST be installed at least 20 cm (8 inches) from (i.e., MUST NOT be installed within 20 cm of) any person. You MUST cease operating this device immediately if requested by the FCC (or ISED in Canada) or licensed wireless service provider. WARNING. E911 location information may not be provided or may be inaccurate for calls served by using this device. ISED CPC-2-1-05: http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08942.html FOR MORE INFORMATION ON REGISTERING YOUR SIGNAL BOOSTER WITH YOUR WIRELESS PROVIDER, PLEASE SEE BELOW: Sprint: http://www.sprint.com/legal/fcc_boosters.html T-Mobile/MetroPCS: https://support.t-mobile.com/docs/DOC-9827 Verizon Wireless: http://www.verizonwireless.com/wcms/consumer/register-signal-booster.html AT&T: https://securec45.securewebsession.com/attsignalbooster.com/ U.S. Cellular: http://www.uscellular.com/uscellular/support/fcc-booster-registration.jsp 11 DRIVE SLEEK CELL PHONE SIGNAL BOOSTER

______ Specifications Drive Sleek Model Number 460035 FCC ID: PWO460035 IC: 4726A-460035 Frequency 698-716 MHz, 729-746 MHz, 777-787 MHz, 824-894 MHz, 1850-1995 MHz, 1710-1755/2110-2155 MHz Maximum Power 700 MHz 700 MHz 800 MHz 1700 MHz 1900 MHz Power output for single cell Band 12/17 Band 13 Band 5 Band 4 Band 2 phone (Uplink) dBm 18.74 21.57 22.65 25.56 19.19 700 MHz 700 MHz 800 MHz 2100 MHz 1900 MHz Power output for single cell Band 12/17 Band 13 Band 5 Band 4 Band 2 phone (Downlink) dBm 2.1 2.1 -2.5 -0.6 2.5 Noise Figure 5 dB nominal Power Requirements 12 V 1.5 A / USB 5V 2.1 A 12 CELL PHONE SIGNAL BOOSTER DRIVE SLEEK

______ (SPECIFICATIONS cont.) The term “IC” before the radio certification number only signifies that Industry Canada technical specifications were met. Each Signal Booster is individually tested and factory set to ensure FCC compliance. The Signal Booster cannot be adjusted without factory reprogramming or disabling the hardware. The Signal Booster will amplify, but not alter incoming and outgoing signals in order to increase coverage of authorized frequency bands only. If the Signal Booster is not in use for five minutes, it will reduce gain until a signal is detected. If a detected signal is too high in a frequency band, or if the Signal Booster detects an oscillation, the Signal Booster will automatically turn the power off on that band. For a detected oscillation the Signal Booster will automatically resume normal operation after a minimum of 1 minute. After 5 (five) such automatic restarts, any problematic bands are permanently shut off until the Signal Booster has been manually restarted by momentarily removing power from the Signal Booster. Noise power, gain, and linearity are maintained by the Signal Booster’s microprocessor. This device complies with Part 15 of FCC rules. Operation is subject to two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by weBoost could void the authority to operate this equipment. 13 DRIVE SLEEK CELL PHONE SIGNAL BOOSTER

2 YEAR WARRANTY weBoost Signal Boosters are warranted for two (2) years against defects in workmanship and/or materials. Warranty cases may be resolved by returning the product directly to the reseller with a dated proof of purchase. Signal Boosters may also be returned directly to the manufacturer at the consumer’s expense, with a dated proof of purchase and a Returned Material Authorization (RMA) number supplied by weBoost. weBoost shall, at its option, either repair or replace the product. This warranty does not apply to any Signal Boosters determined by weBoost to have been subjected to misuse, abuse, neglect, or mishandling that alters or damages physical or electronic properties. Replacement products may include refurbished weBoost products that have been recertified to conform with product specifications. RMA numbers may be obtained by contacting Customer Support DISCLAIMER: The information provided by weBoost is believed to be complete and accurate. However, no responsibility is assumed by weBoost for any business or personal losses arising from its use, or for any infringements of patents or other rights of third parties that may result from its use. 3301 East Deseret Drive, St. George, UT 866.294.1660 www.weboost.com support.weboost.com Copyright © 2016 weBoost. All rights reserved. weBoost products covered by U.S. patent(s) and pending application(s) For patents go to: weboost.com/us/patents NOT AFFILIATED WITH WILSON ANTENNA GDE000009_RevP_ErinFCC_07.10.17


Document Created: 2017-07-26 15:12:08
Document Modified: 2017-07-26 15:12:08
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC