User Manual

FCC ID: PWO460054

Users Manual

Download: PDF
FCCID_4223956

A WILSON ELECTRONICS BRAND DRIVE REACH Vehicle Signal Booster Kit User Manual NEED HELP? support.weboost.com 866.294.1660

______ Index Package Contents 1 STEP 1: Mount Outside Magnetic Antenna 2 STEP 2: Mount Inside Antenna 4 STEP 3: Connect Coax Cables To Booster 5 STEP 4: Connect Power Supply To Booster 6 STEP 5: Plug Power Adapter Into Vehicle’s Power Supply 7 Light Patterns 8 Troubleshooting 9 Safety Guidelines 10 Specifications 11 Warranty 12

________ Package Contents Booster Outside Inside Power & Bracket Antenna Antenna Supply Optional: Adhesive disk for aluminum vehicles 1 DRIVE 4G-X VEHICLE SIGNAL BOOSTER

______ Step 1: Mount Outside Magnetic Antenna Identify a location on the top of your vehicle that is: • Near the center of the roof • At least 12 inches away from any other antennas • At least 6 inches away from any windows (including sunroofs) Clean the surface where you will place the outside antenna. Mount the outside antenna by placing on top of vehicle. 6 in. away from windows (including sunroofs) NOTE: For aluminum roofs, use the included adhesive disk to secure outside antenna in place. WORKS WITH ALL VEHICLES 2 VEHICLE SIGNAL BOOSTER DRIVE 4G-X

______ (STEP 1 cont.) See options below on how cable can be routed with different vehicles. NOTE: The cable is strong enough that it may be shut in most vehicle doors without damaging the cable. Car/Sedan: Cable routed into rear side door. NOTE: When going through car wash, remember to remove your antenna. SUV/Van/Hatchback: Cable routed into top of hatchback door. Truck: Cable routed into side door. 3 DRIVE 4G-X VEHICLE SIGNAL BOOSTER

______ Step 2: Mount Inside Antenna Identify a place to mount the 4G In-Vehicle Antenna, either on the side of the seat or on the dash and mount. The location should be at least 18 inches but no more than 36 inches from where the cellular device will be used. Use the Velcro® adhesive strip/adhesive strip provided and attach to desired location. In-Vehicle Antenna In-Vehicle Antenna 4 VEHICLE SIGNAL BOOSTER DRIVE 4G-X

______ Step 3: Connect Coax Cables To Booster Connect the cable from the Mini-Mag Mount Antenna to the port labeled “Outside Antenna” on the Drive Reach booster. NOTE: Bracket can be used to fasten booster in a specific location if desired. from Outside Antenna Connect the cable from the 4G In-Vehicle Antenna to the port labeled “Inside Antenna” on the booster. from Inside Antenna 5 DRIVE 4G-X VEHICLE SIGNAL BOOSTER

______ Step 4: Connect Power Supply To Booster Connect the power supply cord to the end of the Drive 4G-X labeled “Power.” NOTE: Do NOT connect the power to the Signal Booster until you have connected both the Inside and Outside Antennas. Power Supply 6 VEHICLE SIGNAL BOOSTER DRIVE 4G-X

______ Step 5: Plug Power Adapter Into Vehicle’s Power Supply Plug the power adapter into vehicle’s 12V DC power supply. Power up your Drive 4G-X by flipping the switch on the back of the DC power adapter on. If your Drive 4G-X is working correctly, the light on the power adapter will be red, and the light on the booster will be green. DC Power Adapter NEED HELP? support.weboost.com 866.294.1660 7 DRIVE 4G-X VEHICLE SIGNAL BOOSTER

______ Light Patterns Solid Green This indicates that your booster is functioning properly and there are no issues with installation. Blinking Red, Then Solid Green This indicates that one or more of the booster bands has reduced power due to a feedback loop condition called oscillation. This is a built in safety feature to prevent harmful interference with a nearby cell tower. If you are already experiencing the desired signal boost, then no further adjustments are necessary. If you are not experiencing the desired boost in coverage then refer to the Troubleshooting section below. Solid Red This is due to a feedback loop condition called oscillation. This is a built in safety feature that causes a band to shut off to prevent harmful interference with a nearby cell tower. Refer to Troubleshooting section below. Light Off If the Drive 4  G-X Signal Booster’s light is off, verify your power supply has power. NOTE: The Signal Booster can be reset by disconnecting and reconnecting the power supply. After troubleshooting you must initiate a new power cycle by disconnecting and then reconnecting power to the Booster. NEED HELP? support.weboost.com 866.294.1660 8 VEHICLE SIGNAL BOOSTER DRIVE 4G-X

______ Troubleshooting FIXING BLINKING OR SOLID RED ISSUES This section is only applicable if the booster is red or blinking red and you are not experiencing the desired signal boost. 1 Unplug the Booster’s power supply. 2 Relocate the inside and outside antenna further from each other. The objective is to increase the separation distance between them, so that they will not create this feedback condition discussed before. 3 Plug power supply back in. 4 Monitor the indicator light on your booster. If, after a few seconds of ‘power on’, a solid or blinking red light appears, repeat steps 1 through 3. Increase the separation distance until the condition is corrected and/or desired coverage area is achieved. Note: Horizontal separation of the two antennas typically requires a shorter separation distance than perpendicular separation. 5 If you are having any difficulties while testing or installing your booster, contact our weBoost Customer Support team for assistance (866.294.1660). FREQUENTLY ASKED QUESTIONS What hours can I contact customer support? Customer Support can be reached monday thru friday by calling 866.294.1660, or through our support site at support.weboost.com. Why do I need to create distance between the booster and the antenna? Antennas connected to a booster create spheres of signal. When these spheres overlap, a condition called oscillation occurs. Oscillation can be thought of as noise, which causes the booster to scale down it’s power or shut down to prevent damage. The best way to keep these spheres of signal from overlapping is to maximize separation between the inside and outside antennas. 9 DRIVE 4G-X VEHICLE SIGNAL BOOSTER

______ Safety Guidelines Use only the power supply provided in this package. Use of a non-weBoost product may damage your equipment. The Signal Booster unit is designed for use in an indoor, temperature-controlled environment (less than 150 degrees Fahrenheit). It is not intended for use in attics or similar locations subject to temperatures in excess of that range. All inside antennas must have at least 1.5’ separation distance from all active users. Connecting the Signal Booster directly to the cell phone with use of an adapter will damage the cell phone. RF Safety Warning: Any antenna used with this device must be located at least 8 inches from all persons. This is a CONSUMER device. BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider’s consent. Most wireless providers consent to the use of signal boosters. Some providers may not consent to the use of this device on their network. If you are unsure, contact your provider. In Canada, BEFORE USE you must meet all requirements set out in ISED CPC-2-1-05. You MUST operate this device with approved antennas and cables as specified by the manufacturer. Antennas MUST be installed at least 20 cm (8 inches) from (i.e., MUST NOT be installed within 20 cm of) any person. You MUST cease operating this device immediately if requested by the FCC (or ISED in Canada) or licensed wireless service provider. WARNING. E911 location information may not be provided or may be inaccurate for calls served by using this device. FOR MORE INFORMATION ON REQUIREMENTS SET OUT IN ISED CPC-2-1-05, SEE BELOW: http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08942.html FOR MORE INFORMATION ON REGISTERING YOUR SIGNAL BOOSTER WITH YOUR WIRELESS PROVIDER, PLEASE SEE BELOW: Sprint: http://www.sprint.com/legal/fcc_boosters.html T-Mobile/MetroPCS: https://support.t-mobile.com/docs/DOC-9827 Verizon Wireless: http://www.verizonwireless.com/wcms/consumer/register-signal-booster.html AT&T: https://securec45.securewebsession.com/attsignalbooster.com/ U.S. Cellular: http://www.uscellular.com/uscellular/support/fcc-booster-registration.jsp 10 VEHICLE SIGNAL BOOSTER DRIVE 4G-X

______ Specifications Drive Reach Model Number 460054 FCC ID: PWO460054 IC: 4726A-460054 Connectors SMA-Female Antenna Impedance 50 Ohms Frequency 698-716 MHz, 729-746 MHz, 777-787 MHz, 824-894 MHz, 1850-1995 MHz, 1710-1755/2110-2155 MHz Maximum Power 700 MHz 700 MHz 800 MHz 1700 MHz 1900 MHz Power output for single cell Band 12/17 Band 13 Band 5 Band 4 Band 2 phone (Uplink) dBm 28.3 29.1 29.50 28.50 28.30 700 MHz 700 MHz 800 MHz 2100 MHz 1900 MHz Power output for single cell Band 12/17 Band 13 Band 5 Band 4 Band 2 phone (Downlink) dBm 5.0 5.2 5.2 5 5.1 Noise Figure 5 dB nominal Isolation > 90 dB Power Requirements 6V2A The term “IC” before the radio certification number only signifies that Industry Canada technical specifications were met. Each Signal Booster is individually tested and factory set to ensure FCC compliance. The Signal Booster cannot be adjusted without factory reprogramming or disabling the hardware. The Signal Booster will amplify, but not alter incoming and outgoing signals in order to increase coverage of authorized frequency bands only. If the Signal Booster is not in use for five minutes, it will reduce gain until a signal is detected. If a detected signal is too high in a frequency band, or if the Signal Booster detects an oscillation, the Signal Booster will automatically turn the power off on that band. For a detected oscillation the Signal Booster will automatically resume normal operation after a minimum of 1 minute. After 5 (five) such automatic restarts, any problematic bands are permanently shut off until the Signal Booster has been manually restarted by momentarily removing power from the Signal Booster. Noise power, gain, and linearity are maintained by the Signal Booster’s microprocessor. This device complies with Part 15 of FCC rules. Operation is subject to two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by weBoost could void the authority to operate this equipment. 11 DRIVE 4G-X VEHICLE SIGNAL BOOSTER

2 YEAR WARRANTY weBoost Signal Boosters are warranted for two (2) years against defects in workmanship and/or materials. Warranty cases may be resolved by returning the product directly to the reseller with a dated proof of purchase. Signal Boosters may also be returned directly to the manufacturer at the consumer’s expense, with a dated proof of purchase and a Returned Material Authorization (RMA) number supplied by weBoost. weBoost shall, at its option, either repair or replace the product. This warranty does not apply to any Signal Boosters determined by weBoost to have been subjected to misuse, abuse, neglect, or mishandling that alters or damages physical or electronic properties. Replacement products may include refurbished weBoost products that have been recertified to conform with product specifications. RMA numbers may be obtained by contacting Customer Support DISCLAIMER: The information provided by weBoost is believed to be complete and accurate. However, no responsibility is assumed by weBoost for any business or personal losses arising from its use, or for any infringements of patents or other rights of third parties that may result from its use. NEED HELP? support.weboost.com 866.294.1660 12 VEHICLE SIGNAL BOOSTER DRIVE 4G-X

______ Antenna Kit Options The following accessories are certified by the FCC to be used with the Drive Reach. Mobile Outside Antenna Kit Options Kit 314203-17410 NMO Antenna 10’ RG-174 Kit 311703 Kit 311104-17410 Magnet Mount w/12.5’ RG-174 NMO Antenna 10’ RG-174 Kit 301103 314202 311125 311128 Kit 301126 301113 Magnet Mount w/12.5’ RG-174 Mini-Mag Mount w/12.5’ RG-174 Kit 314203-5810 Kit 304420 NMO Antenna w/10’ RG-58 Marine Antenna w/20’ RG-58 Kit 311130-5810 Kit 311112-17410 Marine Antenna w/10’ RG-58 NMO Antenna 10’ RG-174 Kit 311102 Glass Mount w/14’ RG-58 Mobile Inside Antenna Kit Options Kit 304414 304415 Trucker Antenna w/15’ RG-58 Kit ANT000006 Kit ANT000017 Low Profile Antenna w/10’ LMR-100 Mini-Mag Mount w/10’ LMR-100 Kit 311119 Trucker Antenna w/13.5’ RG-58 Kit 311133 Trucker Antenna w/13.5’ RG-58 13 DRIVE 4G-X VEHICLE SIGNAL BOOSTER

3301 East Deseret Drive, St. George, UT 866.294.1660 www.weboost.com support.weboost.com Copyright © 2017 weBoost. All rights reserved. weBoost products covered by U.S. patent(s) and pending application(s) For patents go to: weboost.com/us/patents NOT AFFILIATED WITH WILSON ANTENNA DriveReach_RevFCC_01.14.19


Document Created: 2019-01-14 13:40:35
Document Modified: 2019-01-14 13:40:35
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC