user manual

FCC ID: PRDRX0P

Users Manual

Download: PDF
FCCID_4282757

2.4GHz Wireless BlueTrace Mouse w/Type C Nano Receiver USER'S GUIDE Ver.:1.00 CAUTION: To use this product properly, please read the user's guide before installing.

Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Radiation Exposure Statement: The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. 1

Functional Introduction 1. Left button 6. DPI Switch Key (LED Indicator) 2. Right button 7. Nano Receiver 3. Scrolling Wheel 8. Battery Cover 4. Forward 9. Connect Button 5. Backward 10. ON/OFF Switch Forward Press this button to view the next page in your Internet browser. Backward Press this button to view the previous page in your Internet browser. DPI Switch The LED indicator under tilt wheel will light up when you plug the mouse into the USB port. The brightness of the indicator indicates the DPI setting in use. There are three different settings:  Bright: 1600 DPI  Dim: 1300 DPI 2

 No light: 800 DPI The default setting is 800 DPI. You can easily switch between DPI settings. In order to save power, the LED display will only last for 10 seconds. Installing the batteries Step 1: Take the battery cover off. Step 2: Insert the battery as shown inside the battery compartment. Pull AA Battery X 1 Step 3: Replace the cover. Step 4: Turn on power switch 3

**Warning: *Please insert the battery with the correct position according to the instruction labeled on the mouse. Step 5: If you need to travel with your wireless mouse, made sure you turn off the POWER SWITCH. Setup the Connection between the Receiver and the Mouse 1. Insert the battery into the mouse, then follow the steps below. 2. In the meantime, to open the mouse under the cover, take the nano receiver out. 3. Plug the Nano receiver into the USB port on your computer. GREEN LED FLASH (0.5 sec. Regularly) Se a rc hing the c ha nne l GREEN LED FLASH (if any action) Cha nnel c o nnec te d GREEN LED ON No a c tio n Connec t to the USB or Mouse port of your c omputer 4. If the mouse does not work, please put it into pairing mode. 5. Pairing: Re-plug the receiver into the USB port on your computer, then 4

press the connect button on the mouse. If the mouse does not work after 10 seconds, pair them again. (The receiver has auto pairing function). 6. The LED indicator on mouse flashes steadily when it is in pairing mode and stops blinking when it is successfully paired with the receiver. 7. When low battery, the battery indicator on the mouse will start to blink. DPI Switch Key *LED Indicator LED Indicator LED is on for 3 sec. Power ON LED Blinks for 3 times During Pairing (LED OFF when paired or failed after 10 sec.) LED Blinks for 10 sec. Low Battery Warning DPI Indicated (when DPI switched) 5


Document Created: 2019-05-16 14:42:20
Document Modified: 2019-05-16 14:42:20
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC