Test Report_rev.pdf

FCC ID: PRDRX0K

Test Report

Download: PDF
FCCID_3837646

FCC Test Report Report No.: RF180227D08 FCC ID: PRDRX0K Test Model: HSA-A001D Received Date: Feb. 27, 2018 Test Date: Mar. 8 ~ 15, 2018 Issued Date: Mar. 19, 2018 Applicant: Acrox Technologies Co., Ltd Address: 4F., No. 89, Minshan St., Neihu Dist., Taipei City 114, Taiwan, R.O.C. Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan (R.O.C.) FCC Registration / Designation Number: 198487 / TW2021 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF180227D08 Page No. 1 / 27 Report Format Version: 6.1.1

Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity...................................................................................................................... 4 2 Summary of Test Results ..................................................................................................................... 5 2.1 Measurement Uncertainty ................................................................................................................... 5 2.2 Modification Record ............................................................................................................................ 5 3 General Information .............................................................................................................................. 6 3.1 General Description of EUT ................................................................................................................ 6 3.2 Description of Test Modes ................................................................................................................... 7 3.2.1 Test Mode Applicability and Tested Channel Detail ............................................................................. 8 3.3 Description of Support Units ............................................................................................................... 9 3.3.1 Configuration of System under Test .................................................................................................... 9 3.4 General Description of Applied Standards .......................................................................................... 9 4 Test Types and Results ...................................................................................................................... 10 4.1 Radiated Emission and Bandedge Measurement............................................................................. 10 4.1.1 Limits of Radiated Emission and Bandedge Measurement .............................................................. 10 4.1.2 Test Instruments ................................................................................................................................. 11 4.1.3 Test Procedures................................................................................................................................. 12 4.1.4 Deviation from Test Standard ............................................................................................................ 12 4.1.5 Test Setup .......................................................................................................................................... 13 4.1.6 EUT Operating Conditions................................................................................................................. 14 4.1.7 Test Results ....................................................................................................................................... 15 4.2 Conducted Emission Measurement .................................................................................................. 20 4.2.1 Limits of Conducted Emission Measurement .................................................................................... 20 4.2.2 Test Instruments ................................................................................................................................ 20 4.2.3 Test Procedures................................................................................................................................. 21 4.2.4 Deviation from Test Standard ............................................................................................................ 21 4.2.5 Test Setup .......................................................................................................................................... 21 4.2.6 EUT Operating Conditions................................................................................................................. 21 4.2.7 Test Results ....................................................................................................................................... 22 4.3 Channel Bandwidth ........................................................................................................................... 24 4.3.1 Test Setup .......................................................................................................................................... 24 4.3.2 Test Instruments ................................................................................................................................ 24 4.3.3 Test Procedure .................................................................................................................................. 24 4.3.4 Deviation from Test Standard ............................................................................................................ 24 4.3.5 EUT Operating Condition .................................................................................................................. 24 4.3.6 Test Results ....................................................................................................................................... 25 5 Pictures of Test Arrangements .......................................................................................................... 26 Appendix – Information on the Testing Laboratories ................................................................................ 27 Report No.: RF180227D08 Page No. 2 / 27 Report Format Version: 6.1.1

Release Control Record Issue No. Description Date Issued RF180227D08 Original release. Mar. 19, 2018 Report No.: RF180227D08 Page No. 3 / 27 Report Format Version: 6.1.1

1 Certificate of Conformity Product: RF receiver dongle Brand: hp Test Model: HSA-A001D Sample Status: Engineering sample Applicant: Acrox Technologies Co., Ltd Test Date: Mar. 8 ~ 15, 2018 Standards: 47 CFR FCC Part 15, Subpart C (Section 15.249) ANSI C63.10: 2013 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s RF characteristics under the conditions specified in this report. Prepared by : , Date: Mar. 19, 2018 Jessica Cheng / Senior Specialist Approved by : , Date: Mar. 19, 2018 Rex Lai / Associate Technical Manager Report No.: RF180227D08 Page No. 4 / 27 Report Format Version: 6.1.1

2 Summary of Test Results 47 CFR FCC Part 15, Subpart C (SECTION 15.249) FCC Test Item Result Remarks Clause Meet the requirement of limit. 15.207 AC Power Conducted Emission PASS Minimum passing margin is -6.41dB at 0.54063MHz. 15.215 Channel Bandwidth Measurement PASS Meet the requirement. Radiated Emission Test Band Edge Measurement 15.209 Meet the requirement of limit. Limit: 50dB less than the peak value 15.249 PASS Minimum passing margin is of fundamental frequency or meet 15.249 (d) -1.35dB at 2400.00MHz. radiated emission limit in section 15.209 15.203 Antenna Requirement PASS No antenna connector is used. 2.1 Measurement Uncertainty Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16-4-2: Expanded Uncertainty Measurement Frequency (k=2) (±) Conducted Emissions at mains ports 150kHz ~ 30MHz 2.77 dB 9kHz ~ 30MHz 2.38 dB Radiated Emissions up to 1 GHz 30MHz ~ 1000MHz 5.54 dB Radiated Emissions above 1 GHz Above 1GHz 5.48 dB 2.2 Modification Record There were no modifications required for compliance. Report No.: RF180227D08 Page No. 5 / 27 Report Format Version: 6.1.1

3 General Information 3.1 General Description of EUT Product RF receiver dongle Brand hp Test Model HSA-A001D Status of EUT Engineering sample Power Supply Rating 5Vdc from host equipment Modulation Type GFSK Operating Frequency 2408MHz ~2474MHz Number of Channel 34 Antenna Type Printed antenna with -1.55dBi gain Antenna Connector N/A Accessory Device N/A Data Cable Supplied N/A Note: The above EUT information is declared by manufacturer and for more detailed features description, please refer to the manufacturer's specifications or user's manual. Report No.: RF180227D08 Page No. 6 / 27 Report Format Version: 6.1.1

3.2 Description of Test Modes 34 channels are provided to this EUT: CH FREQ. (MHz) CH FREQ. (MHz) CH FREQ. (MHz) CH FREQ. (MHz) 1 2408 11 2428 21 2448 31 2468 2 2410 12 2430 22 2450 32 2470 3 2412 13 2432 23 2452 33 2472 4 2414 14 2434 24 2454 34 2474 5 2416 15 2436 25 2456 6 2418 16 2438 26 2458 7 2420 17 2440 27 2460 8 2422 18 2442 28 2462 9 2424 19 2444 29 2464 10 2426 20 2446 30 2466 Report No.: RF180227D08 Page No. 7 / 27 Report Format Version: 6.1.1

3.2.1 Test Mode Applicability and Tested Channel Detail EUT APPLICABLE TO CONFIGURE DESCRIPTION MODE RE1G RE<1G PLC APCM - √ √ √ √ - RE1G: Radiated Emission above 1GHz & Where RE<1G: Radiated Emission below 1GHz Bandedge Measurement PLC: Power Line Conducted Emission APCM: Antenna Port Conducted Measurement NOTE : The EUT had been pre-tested on the positioned of each 3 axis. The worst case was found when positioned on X-plane. Radiated Emission Test (Above 1GHz): Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT CONFIGURE MODE AVAILABLE CHANNEL TESTED CHANNEL MODULATION TYPE - 1 to 34 1, 17, 34 GFSK Radiated Emission Test (Below 1GHz): Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT CONFIGURE MODE AVAILABLE CHANNEL TESTED CHANNEL MODULATION TYPE - 1 to 34 1 GFSK Power Line Conducted Emission Test: Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT CONFIGURE MODE AVAILABLE CHANNEL TESTED CHANNEL MODULATION TYPE - 1 to 34 1 GFSK Antenna Port Conducted Measurement: This item includes all test value of each mode, but only includes spectrum plot of worst value of each mode. Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT CONFIGURE MODE AVAILABLE CHANNEL TESTED CHANNEL MODULATION TYPE - 1 to 34 1, 17, 34 GFSK Test Condition: APPLICABLE TO ENVIRONMENTAL CONDITIONS INPUT POWER TESTED BY RE1G 19deg. C, 79%RH 120Vac, 60Hz (System) James Wei RE<1G 19deg. C, 79%RH 120Vac, 60Hz (System) James Wei PLC 27deg. C, 73%RH 120Vac, 60Hz (System) James Wei APCM 25deg. C, 76%RH 120Vac, 60Hz (System) Saxon Lee Report No.: RF180227D08 Page No. 8 / 27 Report Format Version: 6.1.1

3.3 Description of Support Units The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. ID Product Brand Model No. Serial No. FCC ID Remarks A. Notebook PC ASUS PU401L E9NXBC002007372 FCC DoC Approved Provided by Lab Note: All power cords of the above support units are non-shielded (1.8m). 3.3.1 Configuration of System under Test Noebook (A) EUT USB (Powered from host equipment) 3.4 General Description of Applied Standards The EUT is a RF Product. According to the specifications of the manufacturer, it must comply with the requirements of the following standards: FCC Part 15, Subpart C (15.249) ANSI C63.10-2013 All test items have been performed and recorded as per the above standards. Report No.: RF180227D08 Page No. 9 / 27 Report Format Version: 6.1.1

4 Test Types and Results 4.1 Radiated Emission and Bandedge Measurement 4.1.1 Limits of Radiated Emission and Bandedge Measurement The field strength of emissions from intentional radiators operated within these frequency bands shall comply with the following Fundamental Field Strength of Fundamental Field Strength of Harmonics Frequency (millivolts/meter) (microvolts/meter) 902 ~ 928 MHz 50 500 2400 ~ 2483.5 MHz 50 500 5725 ~ 5875 MHz 50 500 24 ~ 24.25 GHz 250 2500 Emissions radiated outside of the specified frequency bands, except for harmonics, shall be attenuated by at least 50 dB below the level of the fundamental or to the general radiated emission limits as below table, whichever is the lesser attenuation Frequencies Field Strength Measurement Distance (MHz) (microvolts/meter) (meters) 0.009 ~ 0.490 2400/F(kHz) 300 0.490 ~ 1.705 24000/F(kHz) 30 1.705 ~ 30.0 30 30 30 ~ 88 100 3 88 ~ 216 150 3 216 ~ 960 200 3 Above 960 500 3 NOTE: 1. The lower limit shall apply at the transition frequencies. 2. Emission level (dBuV/m) = 20 log Emission level (uV/m). 3. For frequencies above 1000MHz, the field strength limits are based on average detector, however, the peak field strength of any emission shall not exceed the maximum permitted average limits, specified above by more than 20dB under any condition of modulation. Report No.: RF180227D08 Page No. 10 / 27 Report Format Version: 6.1.1

4.1.2 Test Instruments DESCRIPTION & CALIBRATED CALIBRATED MODEL NO. SERIAL NO. MANUFACTURER DATE UNTIL HP Preamplifier 8447D 2432A03504 Feb. 21, 2018 Feb. 20, 2019 HP Preamplifier 8449B 3008A01201 Feb. 22, 2018 Feb. 21, 2019 AMF-6F-260400-33 MITEQ Preamplifier 892164 Feb. 21, 2018 Feb. 20, 2019 -8P Agilent N9038A MY51210129 Feb. 6, 2018 Feb. 5, 2019 TEST RECEIVER Schwarzbeck Antenna VULB 9168 139 Nov. 29, 2017 Nov. 28, 2018 Schwarzbeck Antenna VHBA 9123 480 May 19, 2017 May 18, 2019 Schwarzbeck Horn BBHA-9170 212 Dec. 1, 2017 Nov. 30, 2018 Antenna Schwarzbeck Horn BBHA 9120-D1 D130 Dec. 1, 2017 Nov. 30, 2018 Antenna ADT. Turn Table TT100 0306 NA NA ADT. Tower AT100 0306 NA NA Radiated_V7.6.15. Software NA NA NA 9.5 SUHNER RF cable SF104 CABLE-CH6 Aug. 14, 2017 Aug. 13, 2018 With 4dB PAD SUHNER RF cable SF102 Cable-CH8-3.6m Aug. 14, 2017 Aug. 13, 2018 With 3dB PAD KEYSIGHT MIMO Powermeasurement Test U2021XA U2021XA-001 May 31,2017 May 30,2018 set KEYSIGHT N9030A MY54490260 Jul. 26, 2017 Jul. 25, 2018 Spectrum Analyzer Loop Antenna EMCI LPA600 270 Aug. 11, 2017 Aug. 10, 2019 EMCO Horn Antenna 3115 00028257 Nov. 30, 2017 Nov. 29, 2018 Highpass filter WHK SN 8 NA NA Wainwright Instruments 3.1/18G-10SS ROHDE & SCHWARZ FSV40 101042 Sep. 29, 2017 Sep. 28, 2018 Spectrum Analyzer Anritsu Power Sensor MA2411B 0738404 Apr. 24, 2017 Apr. 23, 2018 Anritsu Power Meter ML2495A 0842014 Apr. 24, 2017 Apr. 23, 2018 NOTE: 1. The calibration interval of the above test instruments is 12/24 months. And the calibrations are traceable to NML/ROC and NIST/USA. 2. The horn antenna and HP preamplifier (model: 8449B) are used only for the measurement of emission frequency above 1GHz if tested. 3. The test was performed in Chamber No. 6. 4. The Industry Canada Reference No. IC 7450E-6. Report No.: RF180227D08 Page No. 11 / 27 Report Format Version: 6.1.1

4.1.3 Test Procedures For Radiated emission below 30MHz a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter chamber room. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. Both X and Y axes of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to Quasi-Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. NOTE: 1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 9kHz at frequency below 30MHz. For Radiated emission above 30MHz a. The EUT was placed on the top of a rotating table 0.8 meters (for 30MHz ~ 1GHz) / 1.5 meters (for above 1GHz) above the ground at 3 meter chamber room for test. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The height of antenna is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to quasi-peak detect function and specified bandwidth with maximum hold mode when the test frequency is below 1 GHz. f. The test-receiver system was set to peak and average detect function and specified bandwidth with maximum hold mode when the test frequency is above 1 GHz. If the peak reading value also meets average limit, measurement with the average detector is unnecessary. Note: 1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120kHz for Quasi-peak detection (QP) at frequency below 1GHz. 2. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and the video bandwidth is 3 MHz for Peak detection (PK) at frequency above 1GHz. 3. All modes of operation were investigated and the worst-case emissions are reported. 4.1.4 Deviation from Test Standard No deviation. Report No.: RF180227D08 Page No. 12 / 27 Report Format Version: 6.1.1

4.1.5 Test Setup For Radiated emission below 30MHz 1m EUT& 3m Support Units Turn Table 80cm Ground Plane Test Receiver For Radiated emission 30MHz to 1GHz Ant. Tower 1-4m Variable EUT& 3m 10m Support Units Turn Table 80cm Ground Plane Test Receiver Report No.: RF180227D08 Page No. 13 / 27 Report Format Version: 6.1.1

For Radiated emission above 1GHz Ant. Tower 1-4m Variable EUT& 3m Support Units Turn Table Absorber 150cm Ground Plane Test Receiver For the actual test configuration, please refer to the attached file (Test Setup Photo). 4.1.6 EUT Operating Conditions a. Connected the EUT with the Notebook. b. Set the EUT under transmission condition continuously at specific channel frequency continuously. Report No.: RF180227D08 Page No. 14 / 27 Report Format Version: 6.1.1

4.1.7 Test Results ABOVE 1GHz DATA CHANNEL TX Channel 1 DETECTOR Peak (PK) FREQUENCY RANGE 1GHz ~ 25GHz FUNCTION Average (AV) ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 2390.00 61.62 PK 74.00 -12.38 1.00 H 74 64.00 -2.38 2 2390.00 45.87 AV 54.00 -8.13 1.00 H 74 48.25 -2.38 3 2400.00 72.65 PK 74.00 -1.35 1.00 H 74 75.10 -2.45 4 2400.00 41.17 AV 54.00 -12.83 1.00 H 74 43.62 -2.45 5 *2408.00 92.25 PK 114.00 -21.75 1.00 H 74 94.74 -2.49 6 *2408.00 85.94 AV 94.00 -8.06 1.00 H 74 88.43 -2.49 7 4816.00 42.65 PK 74.00 -31.35 1.00 H 28 39.33 3.32 8 4816.00 36.34 AV 54.00 -17.66 1.00 H 28 33.02 3.32 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 2390.00 56.73 PK 74.00 -17.27 1.42 V 251 59.11 -2.38 2 2390.00 42.49 AV 54.00 -11.51 1.42 V 251 44.87 -2.38 3 2400.00 65.63 PK 74.00 -8.37 1.42 V 251 68.08 -2.45 4 2400.00 38.87 AV 54.00 -15.13 1.42 V 251 41.32 -2.45 5 *2408.00 85.01 PK 114.00 -28.99 1.42 V 251 87.50 -2.49 6 *2408.00 78.70 AV 94.00 -15.30 1.42 V 251 81.19 -2.49 7 4816.00 40.64 PK 74.00 -33.36 1.00 V 105 37.32 3.32 8 4816.00 34.33 AV 54.00 -19.67 1.00 V 105 31.01 3.32 REMARKS: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level – Limit value 5. " * ": Fundamental frequency. 6. The average value of fundamental and harmonic frequency is: Average = Peak value + 20 log(Duty cycle) Where the duty factor is calculated from following formula: 20 log(Duty cycle) = 20 log(3.8841 ms / 8.029 ms) = -6.31 dB Please see page 18 for plotted duty. Report No.: RF180227D08 Page No. 15 / 27 Report Format Version: 6.1.1

CHANNEL TX Channel 17 DETECTOR Peak (PK) FREQUENCY RANGE 1GHz ~ 25GHz FUNCTION Average (AV) ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 *2440.00 91.91 PK 114.00 -22.09 1.00 H 65 94.56 -2.65 2 *2440.00 85.60 AV 94.00 -8.40 1.00 H 65 88.25 -2.65 3 4880.00 42.54 PK 74.00 -31.46 1.00 H 22 39.21 3.33 4 4880.00 36.23 AV 54.00 -17.77 1.00 H 22 32.90 3.33 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 *2440.00 84.77 PK 114.00 -29.23 1.44 V 255 87.42 -2.65 2 *2440.00 78.46 AV 94.00 -15.54 1.44 V 255 81.11 -2.65 3 4880.00 40.54 PK 74.00 -33.46 1.00 V 119 37.21 3.33 4 4880.00 35.23 AV 54.00 -18.77 1.00 V 119 31.90 3.33 REMARKS: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level – Limit value 5. " * ": Fundamental frequency. 6. The average value of fundamental and harmonic frequency is: Average = Peak value + 20 log(Duty cycle) Where the duty factor is calculated from following formula: 20 log(Duty cycle) = 20 log(3.8841 ms / 8.029 ms) = -6.31 dB Please see page 18 for plotted duty. Report No.: RF180227D08 Page No. 16 / 27 Report Format Version: 6.1.1

CHANNEL TX Channel 34 DETECTOR Peak (PK) FREQUENCY RANGE 1GHz ~ 25GHz FUNCTION Average (AV) ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 *2474.00 91.09 PK 114.00 -22.91 1.00 H 66 93.46 -2.37 2 *2474.00 84.78 AV 94.00 -9.22 1.00 H 66 87.15 -2.37 3 2483.50 63.83 PK 74.00 -10.17 1.00 H 66 66.07 -2.24 4 2483.50 44.68 AV 54.00 -9.32 1.00 H 66 46.92 -2.24 5 4948.00 41.99 PK 74.00 -32.01 1.00 H 22 38.82 3.17 6 4948.00 35.68 AV 54.00 -18.32 1.00 H 22 32.51 3.17 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 *2474.00 84.05 PK 114.00 -29.95 1.44 V 243 86.42 -2.37 2 *2474.00 77.74 AV 94.00 -16.26 1.44 V 243 80.11 -2.37 3 2483.50 58.05 PK 74.00 -15.95 1.44 V 243 60.29 -2.24 4 2483.50 39.59 AV 54.00 -14.41 1.44 V 243 41.83 -2.24 5 4948.00 39.99 PK 74.00 -34.01 1.00 V 114 36.82 3.17 6 4948.00 33.68 AV 54.00 -20.32 1.00 V 114 30.51 3.17 REMARKS: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level – Limit value 5. " * ": Fundamental frequency. 6. The average value of fundamental and harmonic frequency is: Average = Peak value + 20 log(Duty cycle) Where the duty factor is calculated from following formula: 20 log(Duty cycle) = 20 log(3.8841 ms / 8.029 ms) = -6.31 dB Please see page 18 for plotted duty. Report No.: RF180227D08 Page No. 17 / 27 Report Format Version: 6.1.1

20 log(Duty cycle) = 20 log(3.8841 ms / 8.029 ms) = -6.31 dB Report No.: RF180227D08 Page No. 18 / 27 Report Format Version: 6.1.1

BELOW 1GHz WORST-CASE DATA CHANNEL TX Channel 1 DETECTOR Quasi-Peak (QP) FREQUENCY RANGE 9kHz ~ 1GHz FUNCTION ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 51.92 20.75 QP 40.00 -19.25 3.00 H 304 27.84 -7.09 2 84.85 17.56 QP 40.00 -22.44 2.00 H 3 29.99 -12.43 3 529.50 29.05 QP 46.00 -16.95 3.00 H 309 29.50 -0.45 4 660.06 30.99 QP 46.00 -15.01 3.00 H 0 28.77 2.22 5 855.23 34.90 QP 46.00 -11.10 2.00 H 360 29.39 5.51 6 946.75 35.53 QP 46.00 -10.47 2.00 H 82 28.78 6.75 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 52.02 23.34 QP 40.00 -16.66 1.00 V 299 30.44 -7.10 2 118.37 21.86 QP 43.50 -21.64 1.00 V 93 31.44 -9.58 3 472.08 31.56 QP 46.00 -14.44 1.00 V 38 33.17 -1.61 4 590.27 30.13 QP 46.00 -15.87 1.00 V 0 29.05 1.08 5 825.50 34.70 QP 46.00 -11.30 1.00 V 278 29.46 5.24 6 931.86 35.90 QP 46.00 -10.10 1.00 V 0 29.14 6.76 REMARKS: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level – Limit value Report No.: RF180227D08 Page No. 19 / 27 Report Format Version: 6.1.1

4.2 Conducted Emission Measurement 4.2.1 Limits of Conducted Emission Measurement Conducted Limit (dBuV) Frequency (MHz) Quasi-peak Average 0.15 - 0.5 66 - 56 56 - 46 0.50 - 5.0 56 46 5.0 - 30.0 60 50 Note: 1. The lower limit shall apply at the transition frequencies. 2. The limit decreases in line with the logarithm of the frequency in the range of 0.15 to 0.50MHz. 4.2.2 Test Instruments Description & Manufacturer Model No. Serial No. Cal. Date Cal. Due ROHDE & SCHWARZ ESCS 30 100290 Dec. 19, 2017 Dec. 18, 2018 TEST RECEIVER ROHDE & SCHWARZ Artificial Mains ESH2-Z5 100104 Dec. 6, 2017 Dec. 5, 2018 Network (for EUT) LISN With Adapter (for EUT) AD10 C09Ada-001 Dec. 6, 2017 Dec. 5, 2018 ROHDE & SCHWARZ Artificial Mains ESH3-Z5 847265/023 Nov. 03, 2017 Nov. 02, 2018 Network (for peripherals) SCHWARZBECK NNLK8129 8129229 May 9, 2017 May 8, 2018 Artificial Mains Network (For EUT) Software Cond_V7.3.7.4 NA NA NA RF cable (JYEBAO) 5D-FB Cable-C09.01 Feb. 21, 2018 Feb. 20, 2019 With 10dB PAD SUHNER Terminator 65BNC-5001 E1-010789 May 18, 2017 May 17, 2018 (For ROHDE & SCHWARZ LISN) ROHDE & SCHWARZ ESH3-Z5 100220 Nov. 14, 2017 Nov. 13, 2018 Artificial Mains Network (For TV EUT) LISN With Adapter (for TV EUT) 100220 N/A Nov. 14, 2017 Nov. 13, 2018 Notes: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in Shielded Room No. 9. Report No.: RF180227D08 Page No. 20 / 27 Report Format Version: 6.1.1

4.2.3 Test Procedures a. The EUT was placed 0.4 meters from the conducting wall of the shielded room with EUT being connected to the power mains through a line impedance stabilization network (LISN). Other support units were connected to the power mains through another LISN. The two LISNs provide 50 ohm/ 50uH of coupling impedance for the measuring instrument. b. Both lines of the power mains connected to the EUT were checked for maximum conducted interference. c. The frequency range from 150kHz to 30MHz was searched. Emission levels under (Limit - 20dB) was not recorded. NOTE: The resolution bandwidth and video bandwidth of test receiver is 9kHz for quasi-peak detection (QP) and average detection (AV) at frequency 0.15MHz-30MHz. 4.2.4 Deviation from Test Standard No deviation. 4.2.5 Test Setup Vertical Ground Reference Plane Test Receiver EUT 40cm 80cm LISN Horizontal Ground Reference Plane Note: Support units were connected to second LISN. For the actual test configuration, please refer to the attached file (Test Setup Photo). 4.2.6 EUT Operating Conditions Same as item 4.1.6. Report No.: RF180227D08 Page No. 21 / 27 Report Format Version: 6.1.1

4.2.7 Test Results Quasi-Peak (QP) / Frequency Range 150kHz ~ 30MHz Detector Function Average (AV) Phase Of Power : Line (L) Frequency Correction Reading Value Emission Level Limit Margin No Factor (dBuV) (dBuV) (dBuV) (dB) (MHz) (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.16953 10.11 36.57 30.04 46.68 40.15 64.98 54.98 -18.30 -14.83 2 0.53281 10.17 27.58 21.61 37.75 31.78 56.00 46.00 -18.25 -14.22 3 2.19922 10.33 24.26 18.53 34.59 28.86 56.00 46.00 -21.41 -17.14 4 3.48438 10.43 27.97 20.41 38.40 30.84 56.00 46.00 -17.60 -15.16 5 11.30469 10.73 21.77 17.01 32.50 27.74 60.00 50.00 -27.50 -22.26 6 23.24609 11.12 29.37 24.69 40.49 35.81 60.00 50.00 -19.51 -14.19 Remarks: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level – Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value Report No.: RF180227D08 Page No. 22 / 27 Report Format Version: 6.1.1

Quasi-Peak (QP) / Frequency Range 150kHz ~ 30MHz Detector Function Average (AV) Phase Of Power : Neutral (N) Frequency Correction Reading Value Emission Level Limit Margin No Factor (dBuV) (dBuV) (dBuV) (dB) (MHz) (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.16955 10.13 36.73 23.60 46.86 33.73 64.98 54.98 -18.12 -21.25 2 0.21641 10.14 41.23 34.23 51.37 44.37 62.96 52.96 -11.59 -8.59 3 0.54063 10.19 31.91 29.40 42.10 39.59 56.00 46.00 -13.90 -6.41 4 2.20313 10.35 21.30 14.86 31.65 25.21 56.00 46.00 -24.35 -20.79 5 3.48047 10.45 28.82 19.71 39.27 30.16 56.00 46.00 -16.73 -15.84 6 23.15234 10.79 28.43 23.53 39.22 34.32 60.00 50.00 -20.78 -15.68 Remarks: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level – Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value Report No.: RF180227D08 Page No. 23 / 27 Report Format Version: 6.1.1

4.3 Channel Bandwidth 4.3.1 Test Setup Spectrum EUT Attenuator Analyzer 4.3.2 Test Instruments Refer to section 4.1.2 to get information of above instrument. 4.3.3 Test Procedure a. Check the calibration of the measuring instrument using either an internal calibrator or a known signal from an external generator. b. Turn on the EUT and connect it to measurement instrument. Then set it to any one convenient frequency within its operating range. Set a reference level on the measuring instrument equal to the highest peak value. c. Measure the frequency difference of two frequencies that were attenuated 20dB from the reference level. Record the frequency difference as the emission bandwidth. d. Repeat above procedures until all frequencies measured were complete. 4.3.4 Deviation from Test Standard No deviation. 4.3.5 EUT Operating Condition The software provided by client enabled the EUT to transmit and receive data at lowest, middle and highest channel frequencies individually. Report No.: RF180227D08 Page No. 24 / 27 Report Format Version: 6.1.1

4.3.6 Test Results CHANNEL FREQUENCY (MHz) 20dB BANDWIDTH (MHz) 1 2408 2.11 17 2440 2.13 34 2474 2.10 SPECTRUM PLOT of WORST VALUE Report No.: RF180227D08 Page No. 25 / 27 Report Format Version: 6.1.1

5 Pictures of Test Arrangements Please refer to the attached file (Test Setup Photo). Report No.: RF180227D08 Page No. 26 / 27 Report Format Version: 6.1.1

Appendix – Information on the Testing Laboratories We, Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, were founded in 1988 to provide our best service in EMC, Radio, Telecom and Safety consultation. Our laboratories are accredited and approved according to ISO/IEC 17025. If you have any comments, please feel free to contact us at the following: Linko EMC/RF Lab Hsin Chu EMC/RF/Telecom Lab Tel: 886-2-26052180 Tel: 886-3-6668565 Fax: 886-2-26051924 Fax: 886-3-6668323 Hwa Ya EMC/RF/Safety Lab Tel: 886-3-3183232 Fax: 886-3-3270892 Email: service.adt@tw.bureauveritas.com Web Site: www.bureauveritas-adt.com The address and road map of all our labs can be found in our web site also. --- END --- Report No.: RF180227D08 Page No. 27 / 27 Report Format Version: 6.1.1


Document Created: 2018-05-02 17:40:17
Document Modified: 2018-05-02 17:40:17
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC