User Man_PRDRX04

FCC ID: PRDRX03

Users Manual

Download: PDF
FCCID_1602797

2.4GHz Wireless Optical Ergo Mouse w/Nano Receiver USER'S GUIDE Ver.:1.00 CAUTION: To use this product properly, please read the user's guide before installing.

Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. Industry Canada statement: This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. French translation: Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable. 1

Functional Introduction Nano Receiver Battery Cover LED Indicator Connect Button Scrolling Wheel Right button ON/OFF Switch Backward Left button Forward Forward Press this button to view the next page in your Internet browser. Backward Press this button to view the previous page in your Internet browser. Installing the batteries Step 1: Take the battery cover off. Step 2: Insert the batteries as shown inside the battery compartment. Step 3: Replace the cover. Step 4: Turn on power switch 2

2’nd 1’st AAA Battery **Warning: *Please insert the batteries with the correct position according to the instruction labeled in the mouse. Battery warning statement: Do not mix old and new batteries Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, ni-mh, etc) batteries. Setup the Connection between the Receiver and the Mouse 1. Plug the Nano receiver into the USB port of your computer. 3

2. Insert the batteries into the mouse, then follow the steps below. 3. If the mouse is not working, please put it into pairing mode or check the batteries power status. 4. Pairing: Re-plug the receiver into the USB port of your computer, then press the connect button on the mouse. If the mouse does not work after 10 seconds, pair them again. (The receiver has auto pairing function). 5. The LED indicator on mouse flashes steadily when it is in pairing mode and stops blinking when it is successfully paired with the receiver. 6. When the batteries of the mouse is low, the Low Power indicator will start to blink. LED Indicator *Mouse Indicator Red LED is on for 10 sec. Power ON Red LED Blinks for 10 sec. Low Battery Warning Green LED Blinking Pairing (LED OFF when paired or failed after 10 sec.) 4


Document Created: 2011-11-28 11:21:09
Document Modified: 2011-11-28 11:21:09
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC