Test Rpt_PRDRX03_rev. 1

FCC ID: PRDRX03

Test Report

Download: PDF
FCCID_1602795

FCC TEST REPORT REPORT NO. : RF110617C08A MODEL NO. : MRN (refer to item 3.1 for more detail) FCC ID: PRDRX03 RECEIVED : Jun. 17, 2011 TESTED : Jun. 24 ~ Jun. 29, 2011 ISSUED : Jul. 14, 2011 APPLICANT : Acrox Technologies Co., Ltd ADDRESS : 4F., No. 89, Minshan St., Neihu Dist., Taipei City 114, Taiwan, R.O.C. ISSUED BY : Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS : No. 47, 14th Ling, Chia Pau Tsuen, Lin Kou Hsiang, Taipei Hsien 244, Taiwan, R.O.C. TEST LOCATION : No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 29 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product, certification, approval or endorsement by TAF or any government agency. The test results in the report only apply to the tested sample. The test results in this report are traceable to the national or international standards. Report No.: RF110617C08A 1 Report Format Version 4.0.0 Reference No.: 110708C08

Table of Contents RELEASE CONTROL RECORD...............................................................................................3 1. CERTIFICATION ...........................................................................................................4 2. SUMMARY OF TEST RESULTS ...................................................................................5 2.1 MEASUREMENT UNCERTAINTY ................................................................................5 3. GENERAL INFORMATION............................................................................................6 3.1 GENERAL DESCRIPTION OF EUT..............................................................................6 3.2 DESCRIPTION OF TEST MODES................................................................................7 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST ...........................................................7 3.2.2 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ................................8 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS ...............................................9 3.4 DESCRIPTION OF SUPPORT UNITS ..........................................................................9 4. TEST TYPES AND RESULTS .....................................................................................10 4.1 RADIATED EMISSION MEASUREMENT ...................................................................10 4.1.1 LIMITS OF RADIATED EMISSION MEASUREMENT.................................................10 4.1.2 TEST INSTRUMENTS ................................................................................................ 11 4.1.3 TEST PROCEDURES .................................................................................................12 4.1.4 DEVIATION FROM TEST STANDARD .......................................................................12 4.1.5 TEST SETUP ..............................................................................................................13 4.1.6 EUT OPERATING CONDITIONS ................................................................................13 4.1.7 TEST RESULTS ..........................................................................................................14 4.2 CONDUCTED EMISSION MEASUREMENT ..............................................................19 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT............................................19 4.2.2 TEST INSTRUMENTS ................................................................................................19 4.2.3 TEST PROCEDURES .................................................................................................20 4.2.4 DEVIATION FROM TEST STANDARD .......................................................................20 4.2.5 TEST SETUP ..............................................................................................................21 4.2.6 EUT OPERATING CONDITIONS ................................................................................21 4.2.7 TEST RESULTS ..........................................................................................................22 4.3 BAND EDGES MEASUREMENT ................................................................................24 4.3.1 LIMITS OF BAND EDGES MEASUREMENT .............................................................24 4.3.2 TEST INSTRUMENTS ................................................................................................24 4.3.3 TEST PROCEDURE ...................................................................................................24 4.3.4 DEVIATION FROM TEST STANDARD .......................................................................24 4.3.5 EUT OPERATING CONDITION ..................................................................................24 4.3.6 TEST RESULTS ..........................................................................................................25 5. PHOTOGRAPHS OF THE TEST CONFIGURATION..................................................27 6. INFORMATION ON THE TESTING LABORATORIES ................................................28 7. APPENDIX A - MODIFICATIONS RECORDERS FOR ENGINEERING CHANGES TO THE EUT BY THE LAB ..............................................................................................29 Report No.: RF110617C08A 2 Report Format Version 4.0.0 Reference No.: 110708C08

RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED Original release N/A Jul. 14, 2011 Report No.: RF110617C08A 3 Report Format Version 4.0.0 Reference No.: 110708C08

1. CERTIFICATION PRODUCT: Receiver MODEL NO.: MRN (refer to item 3.1 for more detail) BRAND: ACROX APPLICANT: Acrox Technologies Co., Ltd TESTED: Jun. 24 ~ Jun. 29, 2011 TEST SAMPLE: ENGINEERING SAMPLE STANDARDS: FCC Part 15, Subpart C (Section 15.249) ANSI C63.4-2003 ANSI C63.10-2009 The above equipment (Model: MRN) have been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE : Jul. 14, 2011 Andrea Hsia / Specialist APPROVED BY : , DATE : Jul. 14, 2011 Gary Chang / Assistant Manager Report No.: RF110617C08A 4 Report Format Version 4.0.0 Reference No.: 110708C08

2. SUMMARY OF TEST RESULTS The EUT has been tested according to the following specifications: APPLIED STANDARD: FCC Part 15, Subpart C (Section 15.249) STANDARD TEST TYPE RESULT REMARK PARAGRAPH Meet the requirement of limit. 15.207 Conducted Emission Test PASS Minimum passing margin is -14.15dB at 0.215MHz. Radiated Emission Test 15.209 Band Edge Measurement Meet the requirement of limit. 15.249 Limit: 50dB less than the peak value of PASS Minimum passing margin is 15.249 (d) fundamental frequency or meet radiated -4.4dB at 204.89MHz. emission limit in section 15.209 2.1 MEASUREMENT UNCERTAINTY Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16-4-2: MEASUREMENT FREQUENCY UNCERTAINTY Conducted emissions 9kHz~30MHz 2.44 dB 30MHz ~ 200MHz 3.19 dB 200MHz ~1000MHz 3.21 dB Radiated emissions 1GHz ~ 18GHz 2.26 dB 18GHz ~ 40GHz 1.94 dB This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2. Report No.: RF110617C08A 5 Report Format Version 4.0.0 Reference No.: 110708C08

3. GENERAL INFORMATION 3.1 GENERAL DESCRIPTION OF EUT EUT Receiver MODEL NO. MRN (refer to note as below for more detail) FCC ID PRDRX03 POWER SUPPLY 5Vdc (host equipment) MODULATION TYPE GFSK DATA RATE 1M bit/sec. OPERATING FREQUENCY 2403MH~2480MHz NUMBER OF CHANNEL 78 ANTENNA TYPE Printed antenna DATA CABLE NA I/O PORT USB ACCESSORY DEVICES NA NOTE: 1. This is a duplicate report of RF110617C08. The differences are changing the model name, brand name, FCC ID & applicant. 2. All models are electrically identical, different model names are for marketing purpose. Brand Model Remark MRN marketing purpose ACROX MRP marketing purpose 3. The EUT has transmitter and receiver functions. 4. The above EUT information is declared by manufacturer and for more detailed features description, please refer to the manufacturer's specifications or User's Manual. Report No.: RF110617C08A 6 Report Format Version 4.0.0 Reference No.: 110708C08

3.2 DESCRIPTION OF TEST MODES 78 channels are provided to this EUT. Channel Freq. (MHz) Channel Freq. (MHz) Channel Freq. (MHz) 1 2403 27 2429 53 2455 2 2404 28 2430 54 2456 3 2405 29 2431 55 2457 4 2406 30 2432 56 2458 5 2407 31 2433 57 2459 6 2408 32 2434 58 2460 7 2409 33 2435 59 2461 8 2410 34 2436 60 2462 9 2411 35 2437 61 2463 10 2412 36 2438 62 2464 11 2413 37 2439 63 2465 12 2414 38 2440 64 2466 13 2415 39 2441 65 2467 14 2416 40 2442 66 2468 15 2417 41 2443 67 2469 16 2418 42 2444 68 2470 17 2419 43 2445 69 2471 18 2420 44 2446 70 2472 19 2421 45 2447 71 2473 20 2422 46 2448 72 2474 21 2423 47 2449 73 2475 22 2424 48 2450 74 2476 23 2425 49 2451 75 2477 24 2426 50 2452 76 2478 25 2427 51 2453 77 2479 26 2428 52 2454 78 2480 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST Notebook EUT (Power from host equipment) *Test Table Report No.: RF110617C08A 7 Report Format Version 4.0.0 Reference No.: 110708C08

3.2.2 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL EUT APPLICABLE TO CONFIGURE DESCRIPTION MODE RE≥1G RE<1G PLC BM - √ √ √ √ - Where PLC: Power Line Conducted Emission RE<1G: Radiated Emission below 1GHz RE≥1G: Radiated Emission above 1GHz BM: Bandedge Measurement RADIATED EMISSION TEST (ABOVE 1 GHz):  Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations axis and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. AVAILABLE CHANNEL TESTED CHANNEL MODULATION TYPE 1 to 78 1, 38, 78 GFSK RADIATED EMISSION TEST (BELOW 1 GHz):  Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations axis and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. AVAILABLE CHANNEL TESTED CHANNEL MODULATION TYPE 1 to 78 78 GFSK POWER LINE CONDUCTED EMISSION TEST:  Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. AVAILABLE CHANNEL TESTED CHANNEL MODULATION TYPE 1 to 78 78 GFSK BANDEDGE MEASUREMENT:  Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. AVAILABLE CHANNEL TESTED CHANNEL MODULATION TYPE 1 to 78 1, 78 GFSK Report No.: RF110617C08A 8 Report Format Version 4.0.0 Reference No.: 110708C08

TEST CONDITION: INPUT POWER APPLICABLE TO ENVIRONMENTAL CONDITIONS TESTED BY (SYSTEM) RE≥1G 27deg. C, 63%RH, 1001hPa 120Vac, 60Hz Sun Lin RE<1G 27deg. C, 63%RH, 1010hPa 120Vac, 60Hz Sun Lin PLC 25deg. C, 65%RH, 992hPa 120Vac, 60Hz Mark Liao BM 25deg. C, 65%RH, 992hPa 120Vac, 60Hz David Huang 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS The EUT is a RF Product. According to the specifications of the manufacturer, it must comply with the requirements of the following standards: FCC Part 15, Subpart C (Section 15.249) ANSI C63.4-2003 ANSI C63.10-2009 All test items have been performed and recorded as per the above standards. NOTE: The EUT is also considered as a kind of computer peripheral, because the connection to computer is necessary for typical use. It has been verified to comply with the requirements of FCC Part 15, Subpart B, Class B (DoC). The test report has been issued separately. 3.4 DESCRIPTION OF SUPPORT UNITS The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. NO. PRODUCT BRAND MODEL NO. SERIAL NO. FCC ID 1 NOTEBOOK Dell D830 10026042688 E2K4965AGNM NO. SIGNAL CABLE DESCRIPTION OF THE ABOVE SUPPORT UNITS 1 NA NOTE: All power cords of the above support units are non-shielded (1.8m). Report No.: RF110617C08A 9 Report Format Version 4.0.0 Reference No.: 110708C08

4. TEST TYPES AND RESULTS 4.1 RADIATED EMISSION MEASUREMENT 4.1.1 LIMITS OF RADIATED EMISSION MEASUREMENT Emissions radiated outside of the specified bands, shall be according to the general radiated limits in 15.209, 15.249 as following: 15.209 Limit Frequencies Field strength Measurement distance (MHz) (microvolts/meter) (meters) 0.009 ~ 0.490 2400/F(kHz) 300 0.490 ~ 1.705 24000/F(kHz) 30 1.705 ~ 30.0 30 30 30 ~ 88 100 3 88 ~ 216 150 3 216 ~ 960 200 3 Above 960 500 3 15.249 Limit Field Strength of Field Strength of Fundamental Fundamental Harmonics Frequency (millivolts/meter) (microvolts/meter) 902 ~ 928 MHz 50 500 2400 ~ 2483.5 MHz 50 500 5725 ~ 5875 MHz 50 500 24 ~ 24.25 GHz 250 2500 NOTE: 1. The lower limit shall apply at the transition frequencies. 2. Emission level (dBuV/m) = 20 log Emission level (uV/m). 3. As shown in 15.35(b), for frequencies above 1000MHz, the field strength limits are based on average detector, however, the peak field strength of any emission shall not exceed the maximum permitted average limits, specified above by more than 20dB under any condition of modulation. Report No.: RF110617C08A 10 Report Format Version 4.0.0 Reference No.: 110708C08

4.1.2 TEST INSTRUMENTS DESCRIPTION & DATE OF DUE DATE OF MODEL NO. SERIAL NO. MANUFACTURER CALIBRATION CALIBRATION Test Receiver ESI7 838496/016 Dec. 27, 2010 Dec. 26, 2011 ROHDE & SCHWARZ Spectrum Analyzer FSU43 100115 Aug. 02, 2010 Aug. 01, 2011 ROHDE & SCHWARZ BILOG Antenna VULB9168 9168-155 Apr. 12, 2011 Apr. 11, 2012 SCHWARZBECK HORN Antenna BBHA 9120D 9120D-408 Jan. 06, 2011 Jan. 05, 2012 SCHWARZBECK HORN Antenna BBHA 9170 BBHA9170243 Dec. 27, 2010 Dec. 26, 2011 SCHWARZBECK Preamplifier 8449B 3008A01961 Nov. 02, 2010 Nov. 01, 2011 Agilent Preamplifier 8447D 2944A10738 Nov. 02, 2010 Nov. 01, 2011 Agilent RF signal cable SUCOFLEX 104 250792/4 Sep. 03, 2010 Sep. 02, 2011 HUBER+SUHNNER RF signal cable SUCOFLEX 104 283397/4 Sep. 03, 2010 Sep. 02, 2011 HUBER+SUHNNER RF signal cable SUCOFLEX 104 295012/4 Sep. 03, 2010 Sep. 02, 2011 HUBER+SUHNNER Software ADT_Radiated_ NA NA NA ADT. V7.6.15.9.2 Antenna Tower MA 4000 010303 NA NA inn-co GmbH Antenna Tower Controller CO2000 019303 NA NA inn-co GmbH Turn Table TT100. TT93021704 NA NA ADT. Turn Table Controller SC100. SC93021704 NA NA ADT. NOTE: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in HwaYa Chamber 4. 3. The horn antenna and HP preamplifier (model: 8449B) are used only for the measurement of emission frequency above 1GHz if tested. 4. The FCC Site Registration No. is 988962. 5. The IC Site Registration No. is IC7450F-4. Report No.: RF110617C08A 11 Report Format Version 4.0.0 Reference No.: 110708C08

4.1.3 TEST PROCEDURES a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter semi-anechoic chamber. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The antenna is a broadband antenna, and its height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. f. If the emission level of the EUT in peak mode was lower than the limit specified, then testing could be stopped and the peak values of the EUT would be reported. Otherwise the emissions would be re-tested one by one using peak, quasi-peak or average method as specified and then reported in a data sheet. NOTE: 1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120kHz for Quasi-peak detection at frequency below 1GHz. 2. The resolution bandwidth of test receiver/spectrum analyzer is 1MHz and video bandwidth is 3MHz for Peak detection at frequency above 1GHz. 3. All modes of operation were investigated and the worst-case emissions are reported. 4.1.4 DEVIATION FROM TEST STANDARD No deviation. Report No.: RF110617C08A 12 Report Format Version 4.0.0 Reference No.: 110708C08

4.1.5 TEST SETUP For the actual test configuration, please refer to the attached file (Test Setup Photo). 4.1.6 EUT OPERATING CONDITIONS a. Plugged the EUT to the notebook and placed on a testing table. b. Set the transmitter part of EUT under transmission condition continuously at specific channel frequency. Report No.: RF110617C08A 13 Report Format Version 4.0.0 Reference No.: 110708C08

4.1.7 TEST RESULTS ABOVE 1GHz DATA EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 1 FREQUENCY RANGE 1 ~ 25GHz INPUT POWER DETECTOR Peak (PK) 120Vac, 60 Hz (SYSTEM) FUNCTION Average (AV) ENVIRONMENTAL 27deg. C, 63%RH TESTED BY Sun Lin CONDITIONS 1001 hPa ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION TABLE CORRECTION LIMIT ANTENNA RAW VALUE NO. FREQ. (MHz) LEVEL MARGIN (dB) ANGLE FACTOR (dBuV/m) HEIGHT (m) (dBuV) (dBuV/m) (Degree) (dB/m) 1 2390.00 39.7 PK 74.0 -34.3 1.29 H 341 7.80 31.90 2 2390.00 28.9 AV 54.0 -25.1 1.29 H 341 -3.00 31.90 3 2398.00 41.0 PK 74.0 -33.0 1.29 H 341 9.10 31.90 4 2398.00 29.4 AV 54.0 -24.6 1.29 H 341 -2.50 31.90 5 2400.00 47.7 PK 74.0 -26.3 1.29 H 341 15.80 31.90 6 2400.00 2.0 AV 54.0 -52.0 1.29 H 341 -29.90 31.90 7 *2403.00 90.2 PK 114.0 -23.8 1.29 H 341 58.30 31.90 8 *2403.00 44.5 AV 94.0 -49.5 1.29 H 341 12.60 31.90 9 4806.00 64.2 PK 74.0 -9.8 1.39 H 202 26.30 37.90 10 4806.00 18.5 AV 54.0 -35.5 1.39 H 202 -19.40 37.90 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION TABLE CORRECTION LIMIT ANTENNA RAW VALUE NO. FREQ. (MHz) LEVEL MARGIN (dB) ANGLE FACTOR (dBuV/m) HEIGHT (m) (dBuV) (dBuV/m) (Degree) (dB/m) 1 2390.00 39.7 PK 74.0 -34.3 1.56 V 12 7.80 31.90 2 2390.00 28.6 AV 54.0 -25.4 1.56 V 12 -3.30 31.90 3 2398.00 40.7 PK 74.0 -33.3 1.56 V 12 8.80 31.90 4 2398.00 27.5 AV 54.0 -26.5 1.56 V 12 -4.40 31.90 5 2400.00 46.2 PK 74.0 -27.8 1.56 V 12 14.30 31.90 6 2400.00 0.5 AV 54.0 -53.5 1.56 V 12 -31.40 31.90 7 *2403.00 87.8 PK 114.0 -26.2 1.56 V 12 55.90 31.90 8 *2403.00 42.1 AV 94.0 -51.9 1.56 V 12 10.20 31.90 9 4806.00 60.9 PK 74.0 -13.1 1.26 V 78 23.00 37.90 10 4806.00 15.2 AV 54.0 -38.8 1.26 V 78 -22.70 37.90 REMARKS: 1. Emission level (dBuV/m) = Raw Value (dBuV) + Correction Factor (dB/m). 2. Correction Factor (dB/m) = Antenna Factor (dB/m) + Cable Factor (dB). 3. The other emission levels were very low against the limit. 4. Margin value = Emission level – Limit value. 5. “ * “ : Fundamental frequency 6. The average value of fundamental frequency is: Average = Peak value + 20log(Duty cycle) Where the duty factor is calculated from following formula: 20 log (Duty cycle) = 20 log (0.52 ms / 100 ms) = -45.7 dB Please see page 17 for plotted duty. Report No.: RF110617C08A 14 Report Format Version 4.0.0 Reference No.: 110708C08

EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 38 FREQUENCY RANGE 1 ~ 25GHz INPUT POWER DETECTOR Peak (PK) 120Vac, 60 Hz (SYSTEM) FUNCTION Average (AV) ENVIRONMENTAL 27deg. C, 63%RH TESTED BY Sun Lin CONDITIONS 1001 hPa ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION TABLE CORRECTION LIMIT ANTENNA RAW VALUE NO. FREQ. (MHz) LEVEL MARGIN (dB) ANGLE FACTOR (dBuV/m) HEIGHT (m) (dBuV) (dBuV/m) (Degree) (dB/m) 1 *2440.00 90.7 PK 114.0 -23.3 1.24 H 347 58.70 32.00 2 *2440.00 45.0 AV 94.0 -49.0 1.24 H 347 13.00 32.00 3 4880.00 65.2 PK 74.0 -8.8 1.51 H 186 27.10 38.10 4 4880.00 19.5 AV 54.0 -34.5 1.51 H 186 -18.60 38.10 5 7320.00 57.9 PK 74.0 -16.1 1.52 H 93 14.00 43.90 6 7320.00 12.2 AV 54.0 -41.8 1.52 H 93 -31.70 43.90 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION TABLE CORRECTION LIMIT ANTENNA RAW VALUE NO. FREQ. (MHz) LEVEL MARGIN (dB) ANGLE FACTOR (dBuV/m) HEIGHT (m) (dBuV) (dBuV/m) (Degree) (dB/m) 1 *2440.00 88.2 PK 114.0 -25.8 1.58 V 17 56.20 32.00 2 *2440.00 42.5 AV 94.0 -51.5 1.58 V 17 10.50 32.00 3 4880.00 62.8 PK 74.0 -11.2 1.13 V 151 24.70 38.10 4 4880.00 17.1 AV 54.0 -36.9 1.13 V 151 -21.00 38.10 5 7320.00 56.1 PK 74.0 -17.9 1.31 V 105 12.20 43.90 6 7320.00 10.4 AV 54.0 -43.6 1.31 V 105 -33.50 43.90 REMARKS: 1. Emission level (dBuV/m) = Raw Value (dBuV) + Correction Factor (dB/m). 2. Correction Factor (dB/m) = Antenna Factor (dB/m) + Cable Factor (dB). 3. The other emission levels were very low against the limit. 4. Margin value = Emission level – Limit value. 5. “ * “ : Fundamental frequency 6. The average value of fundamental frequency is: Average = Peak value + 20log(Duty cycle) Where the duty factor is calculated from following formula: 20 log (Duty cycle) = 20 log (0.52 ms / 100 ms) = -45.7 dB Please see page 17 for plotted duty. Report No.: RF110617C08A 15 Report Format Version 4.0.0 Reference No.: 110708C08

EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 78 FREQUENCY RANGE 1 ~ 25GHz INPUT POWER DETECTOR Peak (PK) 120Vac, 60 Hz (SYSTEM) FUNCTION Average (AV) ENVIRONMENTAL 27deg. C, 63%RH TESTED BY Sun Lin CONDITIONS 1001 hPa ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION TABLE CORRECTION LIMIT ANTENNA RAW VALUE NO. FREQ. (MHz) LEVEL MARGIN (dB) ANGLE FACTOR (dBuV/m) HEIGHT (m) (dBuV) (dBuV/m) (Degree) (dB/m) 1 *2480.00 89.9 PK 114.0 -24.1 1.22 H 306 57.70 32.20 2 *2480.00 44.2 AV 94.0 -49.8 1.22 H 306 12.00 32.20 3 2483.50 48.2 PK 74.0 -25.8 1.22 H 306 16.00 32.20 4 2483.50 2.5 AV 54.0 -51.5 1.22 H 306 -29.70 32.20 5 2485.50 40.4 PK 74.0 -33.6 1.22 H 306 8.20 32.20 6 2485.50 27.6 AV 54.0 -26.4 1.22 H 306 -4.60 32.20 7 2491.00 40.8 PK 74.0 -33.2 1.22 H 306 8.60 32.20 8 2491.00 30.5 AV 54.0 -23.5 1.22 H 306 -1.70 32.20 9 4960.00 64.9 PK 74.0 -9.1 1.34 H 190 26.60 38.30 10 4960.00 19.2 AV 54.0 -34.8 1.34 H 190 -19.10 38.30 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION TABLE CORRECTION LIMIT ANTENNA RAW VALUE NO. FREQ. (MHz) LEVEL MARGIN (dB) ANGLE FACTOR (dBuV/m) HEIGHT (m) (dBuV) (dBuV/m) (Degree) (dB/m) 1 *2480.00 87.2 PK 114.0 -26.8 1.58 V 25 55.00 32.20 2 *2480.00 41.5 AV 94.0 -52.5 1.58 V 25 9.30 32.20 3 2483.50 46.1 PK 74.0 -27.9 1.58 V 25 13.90 32.20 4 2483.50 0.4 AV 54.0 -53.6 1.58 V 25 -31.80 32.20 5 2485.50 38.0 PK 74.0 -36.0 1.58 V 25 5.80 32.20 6 2485.50 25.5 AV 54.0 -28.5 1.58 V 25 -6.70 32.20 7 2491.00 35.8 PK 74.0 -38.2 1.58 V 25 3.60 32.20 8 2491.00 28.0 AV 54.0 -26.0 1.58 V 25 -4.20 32.20 9 4960.00 60.8 PK 74.0 -13.2 1.22 V 107 22.50 38.30 10 4960.00 15.1 AV 54.0 -38.9 1.22 V 107 -23.20 38.30 REMARKS: 1. Emission level (dBuV/m) = Raw Value (dBuV) + Correction Factor (dB/m). 2. Correction Factor (dB/m) = Antenna Factor (dB/m) + Cable Factor (dB). 3. The other emission levels were very low against the limit. 4. Margin value = Emission level – Limit value. 5. “ * “ : Fundamental frequency 6. The average value of fundamental frequency is: Average = Peak value + 20log(Duty cycle) Where the duty factor is calculated from following formula: 20 log (Duty cycle) = 20 log (0.52 ms / 100 ms) = -45.7 dB Please see page 17 for plotted duty. Report No.: RF110617C08A 16 Report Format Version 4.0.0 Reference No.: 110708C08

20 log (Duty cycle) = 20 log (0.52 ms / 100 ms) = -45.7 dB Report No.: RF110617C08A 17 Report Format Version 4.0.0 Reference No.: 110708C08

BELOW 1GHz WORST-CASE DATA EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 78 FREQUENCY RANGE Below 1000MHz INPUT POWER DETECTOR 120Vac, 60 Hz Quasi-Peak (SYSTEM) FUNCTION ENVIRONMENTAL 27deg. C, 63%RH TESTED BY Sun Lin CONDITIONS 1010 hPa ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION TABLE CORRECTION LIMIT ANTENNA RAW VALUE NO. FREQ. (MHz) LEVEL MARGIN (dB) ANGLE FACTOR (dBuV/m) HEIGHT (m) (dBuV) (dBuV/m) (Degree) (dB/m) 1 204.89 39.1 QP 43.5 -4.4 1.75 H 265 26.80 12.30 2 265.16 39.5 QP 46.0 -6.5 1.25 H 235 25.40 14.10 3 309.88 39.5 QP 46.0 -6.5 1.00 H 10 23.90 15.60 4 399.31 39.1 QP 46.0 -6.9 1.50 H 82 20.50 18.60 5 442.09 39.4 QP 46.0 -6.6 1.25 H 52 19.60 19.80 6 533.47 36.7 QP 46.0 -9.3 1.00 H 49 14.50 22.20 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION TABLE CORRECTION LIMIT ANTENNA RAW VALUE NO. FREQ. (MHz) LEVEL MARGIN (dB) ANGLE FACTOR (dBuV/m) HEIGHT (m) (dBuV) (dBuV/m) (Degree) (dB/m) 1 39.62 28.3 QP 40.0 -11.7 1.00 V 316 14.30 14.00 2 146.56 32.9 QP 43.5 -10.6 1.00 V 88 18.10 14.80 3 204.89 29.5 QP 43.5 -14.0 1.50 V 241 17.20 12.30 4 333.21 28.9 QP 46.0 -17.1 1.50 V 4 12.50 16.40 5 492.64 31.3 QP 46.0 -14.7 1.00 V 88 10.10 21.20 6 768.73 32.2 QP 46.0 -13.8 1.00 V 319 5.60 26.60 REMARKS: 1. Emission level (dBuV/m) = Raw Value (dBuV) + Correction Factor (dB/m). 2. Correction Factor (dB/m) = Antenna Factor (dB/m) + Cable Factor (dB). 3. The other emission levels were very low against the limit. 4. Margin value = Emission level – Limit value. Report No.: RF110617C08A 18 Report Format Version 4.0.0 Reference No.: 110708C08

4.2 CONDUCTED EMISSION MEASUREMENT 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT FREQUENCY OF EMISSION (MHz) CONDUCTED LIMIT (dBµV) Quasi-peak Average 0.15 ~ 0.5 66 to 56 56 to 46 0.5 ~ 5 56 46 5 ~ 30 60 50 NOTE: 1. The lower limit shall apply at the transition frequencies. 2. The limit decreases in line with the logarithm of the frequency in the range of 0.15 to 0.50 MHz. 3. All emanations from a class A/B digital device or system, including any network of conductors and apparatus connected thereto, shall not exceed the level of field strengths specified above. 4.2.2 TEST INSTRUMENTS DESCRIPTION & DATE OF DUE DATE OF MODEL NO. SERIAL NO. MANUFACTURER CALIBRATION CALIBRATION Test Receiver ESCS30 100289 Nov. 23, 2010 Nov. 22, 2011 ROHDE & SCHWARZ RF signal cable 5D-FB Cable-HYCO2-01 Dec. 30, 2010 Dec. 29, 2011 Woken LISN ESH2-Z5 100100 Jan. 06, 2011 Jan. 05, 2012 ROHDE & SCHWARZ LISN ESH3-Z5 100311 Jul. 08, 2010 Jul. 07, 2011 ROHDE & SCHWARZ V-LISN NNBL 8226-2 8226-142 Jul. 12, 2010 Jul. 11, 2011 SCHWARZBECK LISN ENV216 100072 Jun. 10, 2011 Jun. 09, 2012 ROHDE & SCHWARZ Software ADT_Cond_ NA NA NA ADT V7.3.7 NOTE: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in HwaYa Shielded Room 2. 3. The VCCI Site Registration No. is C-2047. Report No.: RF110617C08A 19 Report Format Version 4.0.0 Reference No.: 110708C08

4.2.3 TEST PROCEDURES a. The EUT was placed 0.4 meters from the conducting wall of the shielded room with EUT being connected to the power mains through a line impedance stabilization network (LISN). Other support units were connected to the power mains through another LISN. The two LISNs provide 50 ohm/ 50uH of coupling impedance for the measuring instrument. b. Both lines of the power mains connected to the EUT were checked for maximum conducted interference. c. The frequency range from 150kHz to 30MHz was searched. Emission levels under (Limit - 20dB) was not recorded. NOTE: All modes of operation were investigated and the worst-case emissions are reported. 4.2.4 DEVIATION FROM TEST STANDARD No deviation. Report No.: RF110617C08A 20 Report Format Version 4.0.0 Reference No.: 110708C08

4.2.5 TEST SETUP V e r tic a l G r o u n d R e fe r e n c e P la n e Te s t R e c e iv e r EUT 40cm 80cm L IS N H o r iz o n ta l G r o u n d R e fe r e n c e P la n e N o te : 1 .S u p p o r t u n its w e r e c o n n e c te d to s e c o n d L IS N . 2 .B o th o f L IS N s ( A M N ) a r e 8 0 c m fr o m E U T a n d a t le a s t 8 0 fr o m o th e r u n its a n d o th e r m e ta l p la n e s For the actual test configuration, please refer to the attached file (Test Setup Photo). 4.2.6 EUT OPERATING CONDITIONS Same as 4.1.6. Report No.: RF110617C08A 21 Report Format Version 4.0.0 Reference No.: 110708C08

4.2.7 TEST RESULTS CONDUCTED WORST-CASE DATA PHASE Line 1 6dB BANDWIDTH 9kHz Emission Freq. Corr. Reading Value Limit Margin Level No Factor [dB (uV)] [dB (uV)] [dB (uV)] (dB) [MHz] (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.150 0.15 40.99 - 41.14 - 66.00 56.00 -24.86 - 2 0.209 0.15 48.28 - 48.43 - 63.26 53.26 -14.83 - 3 0.310 0.16 33.49 - 33.65 - 59.97 49.97 -26.32 - 4 0.556 0.18 24.75 - 24.93 - 56.00 46.00 -31.07 - 5 1.406 0.20 25.59 - 25.79 - 56.00 46.00 -30.21 - 6 9.176 0.53 28.00 - 28.53 - 60.00 50.00 -31.47 - REMARKS: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. "-": The Quasi-peak reading value also meets average limit and measurement with the average detector is unnecessary. 3. The emission levels of other frequencies were very low against the limit. 4. Margin value = Emission level - Limit value 5. Correction factor = Insertion loss + Cable loss 6. Emission Level = Correction Factor + Reading Value. Report No.: RF110617C08A 22 Report Format Version 4.0.0 Reference No.: 110708C08

PHASE Line 2 6dB BANDWIDTH 9kHz Emission Freq. Corr. Reading Value Limit Margin Level No Factor [dB (uV)] [dB (uV)] [dB (uV)] (dB) [MHz] (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.150 0.16 41.45 - 41.61 - 66.00 56.00 -24.39 - 2 0.215 0.17 48.70 - 48.87 - 63.02 53.02 -14.15 - 3 0.307 0.18 35.13 - 35.31 - 60.04 50.04 -24.73 - 4 0.416 0.19 28.55 - 28.74 - 57.54 47.54 -28.79 - 5 0.607 0.20 24.74 - 24.94 - 56.00 46.00 -31.06 - 6 9.520 0.49 29.05 - 29.54 - 60.00 50.00 -30.46 - REMARKS: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. "-": The Quasi-peak reading value also meets average limit and measurement with the average detector is unnecessary. 3. The emission levels of other frequencies were very low against the limit. 4. Margin value = Emission level - Limit value 5. Correction factor = Insertion loss + Cable loss 6. Emission Level = Correction Factor + Reading Value. Report No.: RF110617C08A 23 Report Format Version 4.0.0 Reference No.: 110708C08

4.3 BAND EDGES MEASUREMENT 4.3.1 LIMITS OF BAND EDGES MEASUREMENT Below –50dB of the highest emission level of operating band (in 100kHz Resolution Bandwidth). 4.3.2 TEST INSTRUMENTS DESCRIPTION & DATE OF DUE DATE OF MODEL NO. SERIAL NO. MANUFACTURER CALIBRATION CALIBRATION SPECTRUM ANALYZER FSP40 100040 Jul. 17, 2010 Jul. 16, 2011 R&S NOTE: The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 4.3.3 TEST PROCEDURE The transmitter output was connected to the spectrum analyzer via a low lose cable. Set both RBW and VBW of spectrum analyzer to 100 kHz and 300 kHz with suitable frequency span including 100 MHz bandwidth from band edge. The band edges was measured and recorded. The spectrum plots are attached on the following pages. 4.3.4 DEVIATION FROM TEST STANDARD No deviation. 4.3.5 EUT OPERATING CONDITION The software provided by client to enable the EUT under transmission condition continuously at lowest and highest channel frequencies individually. Report No.: RF110617C08A 24 Report Format Version 4.0.0 Reference No.: 110708C08

4.3.6 TEST RESULTS The spectrum plots are attached on the following images. D1 line indicates the highest level, and D2 line indicates the 50dB offset below D1. It shows compliance with the requirement in part 15.249 (d). Report No.: RF110617C08A 25 Report Format Version 4.0.0 Reference No.: 110708C08

Report No.: RF110617C08A 26 Report Format Version 4.0.0 Reference No.: 110708C08

5. PHOTOGRAPHS OF THE TEST CONFIGURATION Please refer to the attached file (Test Setup Photo). Report No.: RF110617C08A 27 Report Format Version 4.0.0 Reference No.: 110708C08

6. INFORMATION ON THE TESTING LABORATORIES We, Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, were founded in 1988 to provide our best service in EMC, Radio, Telecom and Safety consultation. Our laboratories are accredited and approved according to ISO/IEC 17025. Copies of accreditation certificates of our laboratories obtained from approval agencies can be downloaded from our web site: www.adt.com.tw/index.5.phtml. If you have any comments, please feel free to contact us at the following: Linko EMC/RF Lab Hsin Chu EMC/RF Lab Tel: 886-2-26052180 Tel: 886-3-5935343 Fax: 886-2-26051924 Fax: 886-3-5935342 Hwa Ya EMC/RF/Safety Telecom Lab Tel: 886-3-3183232 Fax: 886-3-3185050 Email: service.adt@tw.bureauveritas.com Web Site: www.adt.com.tw The address and road map of all our labs can be found in our web site also. Report No.: RF110617C08A 28 Report Format Version 4.0.0 Reference No.: 110708C08

7. APPENDIX A - MODIFICATIONS RECORDERS FOR ENGINEERING CHANGES TO THE EUT BY THE LAB No any modifications are made to the EUT by the lab during the test. ---END--- Report No.: RF110617C08A 29 Report Format Version 4.0.0 Reference No.: 110708C08


Document Created: 2011-12-08 17:40:40
Document Modified: 2011-12-08 17:40:40
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC