Test Report

FCC ID: PQN66802RX2G4

Test Report

Download: PDF
FCCID_4018586

2/F., Garment Centre, 576 Castle Peak Road, Kowloon, Hong Kong. Telephone: (852) 2173 8888 Facsimile: (852) 2785 5487 www.intertek.com TEST REPORT Report No.: 18080393HKG‐003 Spin Master Toys Far East Ltd. Application For Certification (Original Grant) FCC ID: PQN66802RX2G4 Transceiver Prepared and Checked by: Approved by: Digitally signed by Kenneth Wong Location: Intertek Testing Services Hong Kong Ltd. Signed On File Lee Yee Yat, Adrian Wong Kwok Yeung, Kenneth Assistant Engineer Senior Lead Engineer Date: August 28, 2018 Intertek’s standard Terms and Conditions can be obtained at our website http://www.intertek.com/terms/. The test report only allows to be revised within the retention period unless further standard or the requirement was noticed. This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. © 2017 Intertek Page 1 of 20

Spin Master Toys Far East Ltd. Intertek Report No: 18080393HKG‐003 TEST REPORT GENERAL INFORMATION Grantee: Spin Master Toys Far East Ltd. Grantee Address: Room 1113, 11/F., Chinachem Golden Plaza, 77 Mody Road, Tsim Sha Tsui East, Kowloon, Hong Kong. Contact Person: Andy Wong Tel: (852) 2301 3822 Fax: (852) 2301 1822 e‐mail: andyw@spinmaster.com Manufacturer: Spin Master Toys Manufacturer Address: 1113A, 11/F., Chinachem Golden Plaza, 77 Mody Road, Tsim Sha Tsui East, Kowloon, Hong Kong. Brand Name: Spin Master Ltd. Model: 66802 Phantom No.: 20103726/20108558/20103725/20115414 Type of EUT: Transceiver Description of EUT: MJD RDC 1 to 10 Grave Digger Serial Number: N/A FCC ID: PQN66802RX2G4 Date of Sample Submitted: August 08, 2018 Date of Test: August 08, 2018 to August 22, 2018 Report No.: 18080393HKG‐003 Report Date: August 28, 2018 Environmental Conditions: Temperature: +10 to 40°C Humidity: 10 to 90% Page 2 of 20

Spin Master Toys Far East Ltd. Intertek Report No: 18080393HKG‐003 TEST REPORT SUMMARY OF TEST RESULT Test Specification Reference Results Radiated Emission 15.249, 15.209 Pass Radiated Emission on the Bandedge Radiated Emission in Restricted Bands 15.205 Pass The equipment under test is found to be complying with the following standards: FCC Part 15, October 1, 2017 Edition Note: 1. The EUT uses a permanently attached antenna which, in accordance to section 15.203, is considered sufficient to comply with the pervisions of this section. 2. Pursuant to FCC part 15 Section 15.215(c), the 20 dB bandwidth of the emission was contained within the frequency band designated (mentioned as above) which the EUT operated. The effects, if any, from frequency sweeping, frequency hopping, other modulation techniques and frequency stability over excepted variations in temperature and supply voltage were considered. Page 3 of 20

Spin Master Toys Far East Ltd. Intertek Report No: 18080393HKG‐003 TEST REPORT TABLE OF CONTENTS 1.0 GENERAL DESCRIPTION ................................................................................................ 5 1.1 Product Description .................................................................................................5 1.2 Related Submittal(s) Grants......................................................................................5 1.3 Test Methodology ....................................................................................................6 1.4 Test Facility ..............................................................................................................6 2.0 SYSTEM TEST CONFIGURATION..................................................................................... 7 2.1 Justification..............................................................................................................7 2.2 EUT Exercising Software ...........................................................................................7 2.3 Special Accessories...................................................................................................7 2.4 Measurement Uncertainty .......................................................................................7 2.5 Support Equipment List and Description ..................................................................7 3.0 EMISSION RESULTS....................................................................................................... 8 3.1 Field Strength Calculation.........................................................................................8 3.2 Radiated Emission Configuration Photograph...........................................................9 3.3 Radiated Emission Data............................................................................................9 4.0 EQUIPMENT PHOTOGRAPHS ...................................................................................... 13 5.0 PRODUCT LABELLING.................................................................................................. 13 6.0 TECHNICAL SPECIFICATIONS ....................................................................................... 13 7.0 INSTRUCTION MANUAL.............................................................................................. 13 8.0 MISCELLANEOUS INFORMATION ................................................................................ 14 8.1 Radiated Emission on the Bandedge.......................................................................14 8.2 Discussion of Pulse Desensitization ........................................................................15 8.3 Calculation of Average Factor.................................................................................15 8.4 Emissions Test Procedures .....................................................................................17 9.0 EQUIPMENT LIST........................................................................................................ 20 Page 4 of 20

Spin Master Toys Far East Ltd. Intertek Report No: 18080393HKG‐003 TEST REPORT 1.0 GENERAL DESCRIPTION 1.1 Product Description The Equipment Under Test (EUT), is a portable 2.4GHz Transceiver (RC car). The operation frequency range is between 2411MHz and 2472MHz with 21 channels, where 2457MHz is the pairing channel.\ 2411 2443 2413 2445 2420 2451 2422 2453 2424 2455 2426 2457 2428 2461 2435 2468 2437 2470 2439 2472 2441 Description/Controller.doc The EUT is powered by 2 x 3.2V rechargeable battery. After switch on the EUT, the car will be moved forward or backward, turned left or right based on the switches pressed in the controller. Antenna Type: Internal, Integral For electronic filing, the brief circuit description is saved with filename: descri.pdf. 1.2 Related Submittal(s) Grants This is a single application for certification of a transceiver. The Certification procedure of transceiver for this transceiver (with FCC ID: PQN66802TX2G4) is being processed as the same time of this application. Page 5 of 20

Spin Master Toys Far East Ltd. Intertek Report No: 18080393HKG‐003 TEST REPORT 1.3 Test Methodology Radiated emission measurements were performed according to the procedures in ANSI C63.10 (2013). All radiated measurements were performed in an 3m Chamber. Preliminary scans were performed in the 3m Chamber only to determine worst case modes. All radiated tests were performed at an antenna to EUT distance of 3 meters, unless stated otherwise in the “Justification Section” of this Application. 1.4 Test Facility The 3m Chamber facility used to collect the radiated data is located at Workshop No. 3, G/F., World‐Wide Industrial Centre, 43‐47 Shan Mei Street, Fo Tan, Sha Tin, N.T., Hong Kong. This test facility and site measurement data have been placed on file with the FCC. Page 6 of 20

Spin Master Toys Far East Ltd. Intertek Report No: 18080393HKG‐003 TEST REPORT 2.0 SYSTEM TEST CONFIGURATION 2.1 Justification The system was configured for testing in a typical fashion (as a customer would normally use it), and in the confines as outlined in ANSI C63.10 (2013). The device was powered by new DC 6.4V (2 x 3.2V rechargeable batteries). For maximizing emissions, the EUT was rotated through 360°, the antenna height was varied from 1 meter to 4 meters above the ground plane, and the antenna polarization was changed. This step by step procedure for maximizing emissions led to the data reported in Exhibit 3.0. The unit was operated standalone and placed in the center of the turntable. The equipment under test (EUT) was configured for testing in a typical fashion (as a customer would normally use it). The EUT was mounted to a plastic stand if necessary and placed on the wooden turntable, which enabled the engineer to maximize emissions through its placement in the three orthogonal axes. 2.2 EUT Exercising Software There was no special software to exercise the device. Once the unit is powered up, it transmits the RF signal continuously. 2.3 Special Accessories There are no special accessories necessary for compliance of this product. 2.4 Measurement Uncertainty When determining of the test conclusion, the Measurement Uncertainty of test has been considered. 2.5 Support Equipment List and Description N/A. Page 7 of 20

Spin Master Toys Far East Ltd. Intertek Report No: 18080393HKG‐003 TEST REPORT 3.0 EMISSION RESULTS Data is included of the worst case configuration (the configuration which resulted in the highest emission levels). A sample calculation, configuration photographs and data tables of the emissions are included. 3.1 Field Strength Calculation The field strength is calculated by adding the Antenna Factor and Cable Factor, and subtracting the Amplifier Gain (if any), Average Factor (optional) from the measured reading. The basic equation with a sample calculation is as follows: FS = RA + AF + CF ‐ AG ‐ AV where FS = Field Strength in dBµV/m RA = Receiver Amplitude (including preamplifier) in dBµV CF = Cable Attenuation Factor in dB AF = Antenna Factor in dB AG = Amplifier Gain in dB AV = Average Factor in dB In the following table(s), the reading shown on the data table reflects the preamplifier gain. An example for the calculations in the following table is as follows: FS = RR + LF where FS = Field Strength in dBµV/m RR = RA ‐ AG ‐ AV in dBµV LF = CF + AF in dB Assume a receiver reading of 52.0 dBµV is obtained. The antenna factor of 7.4 dB and cable factor of 1.6 dB are added. The amplifier gain of 29 dB and average factor of 5 dB are subtracted, giving a field strength of 27 dBµV/m. This value in dBµV/m was converted to its corresponding level in µV/m. RA = 52.0 dBµV/m AF = 7.4 dB RR = 18.0 dBµV CF = 1.6 dB LF = 9.0 dB AG = 29.0 dB AV = 5.0 dB FS = RR + LF FS = 18 + 9 = 27 dBµV/m Level in µV/m = Common Antilogarithm [(27 dBµV/m)/20] = 22.4 µV/m Page 8 of 20

Spin Master Toys Far East Ltd. Intertek Report No: 18080393HKG‐003 TEST REPORT 3.2 Radiated Emission Configuration Photograph The worst case in radiated emission was found at 2483.5 MHz For electronic filing, the worst case radiated emission configuration photographs are saved with filename: radiated photos.pdf. 3.3 Radiated Emission Data The data on the following page lists the significant emission frequencies, the limit and the margin of compliance. Numbers with a minus sign are below the limit. Judgment: Passed by 6.8 dB Page 9 of 20

Spin Master Toys Far East Ltd. Intertek Report No: 18080393HKG‐003 TEST REPORT RADIATED EMISSIONS Model: 66802 Date of Test: August 22, 2018 Worst‐Case Operating Mode: Transmitting Table 1 Pursuant to FCC Part 15 Section 15.249 Requirement Lowest Channel Pre-Amp Antenna Net at Average Calculated Average Limit Polari- Frequency Reading Gain Factor 3m - Peak Factor at 3m at 3m Margin zation (MHz) (dBμV) (dB) (dB) (dBμV/m) (dB) (dBμV/m) (dBμV/m) (dB) V 2411.000 100.8 33 29.4 97.2 17.9 79.3 94.0 -14.7 V 2400.000 67.6 33 29.4 64.0 17.9 46.1 54.0 -7.9 H 4822.000 44.7 33 34.9 46.6 17.9 28.7 54.0 -25.3 V 7233.000 44.0 33 37.9 48.9 17.9 31.0 54.0 -23.0 V 9644.000 42.7 33 40.4 50.1 17.9 32.2 54.0 -21.8 H 12055.000 45.1 33 40.5 52.6 17.9 34.7 54.0 -19.3 H 14466.000 46.8 33 40.0 53.8 17.9 35.9 54.0 -18.1 Pre-Amp Antenna Net at Peak Limit Polari- Frequency Reading Gain Factor 3m - Peak at 3m Margin zation (MHz) (dBμV) (dB) (dB) (dBμV/m) (dBμV/m) (dB) V 2411.000 100.8 33 29.4 97.2 114.0 -16.8 V 2400.000 67.6 33 29.4 64.0 74.0 -10.0 H 4822.000 44.7 33 34.9 46.6 74.0 -27.4 V 7233.000 44.0 33 37.9 48.9 74.0 -25.1 V 9644.000 42.7 33 40.4 50.1 74.0 -23.9 H 12055.000 45.1 33 40.5 52.6 74.0 -21.4 H 14466.000 46.8 33 40.0 53.8 74.0 -20.2 NOTES: 1. Peak Detector Data unless otherwise stated. 2. All measurements were made at 3 meters. Harmonic emissions not detected at the 3‐ meter distances were measured at 0.3‐meter and an inverse proportional extrapolation was performed to compare the signal level to the 3‐meter limit. No other harmonic emissions than those reported were detected at a test distance of 0.3‐meter. 3. Negative sign in the column shows value below limit. 4. Horn antenna is used for the emission over 1000MHz. 5. Emission (the row indicated by bold italic) within the restricted band meets the requirement of FCC Part 15 Section 15.205. 6. Measurement Uncertainty is ±5.3dB at a level of confidence of 95%. Page 10 of 20

Spin Master Toys Far East Ltd. Intertek Report No: 18080393HKG‐003 TEST REPORT Model: 66802 Date of Test: August 22, 2018 Worst‐Case Operating Mode: Transmitting Table 2 Pursuant to FCC Part 15 Section 15.249 Requirement Middle Channel Pre-Amp Antenna Net at Average Calculated Average Limit Polari- Frequency Reading Gain Factor 3m - Peak Factor at 3m at 3m Margin zation (MHz) (dBμV) (dB) (dB) (dBμV/m) (dB) (dBμV/m) (dBμV/m) (dB) V 2441.000 103.2 33 29.4 99.6 17.9 81.7 94.0 -12.3 H 4882.000 44.0 33 34.9 45.9 17.9 28.0 54.0 -26.0 H 7323.000 43.4 33 37.9 48.3 17.9 30.4 54.0 -23.6 H 9764.000 42.3 33 40.4 49.7 17.9 31.8 54.0 -22.2 V 12205.000 45.0 33 40.5 52.5 17.9 34.6 54.0 -19.4 H 14646.000 48.0 33 38.4 53.4 17.9 35.5 54.0 -18.5 Pre-Amp Antenna Net at Peak Limit Polari- Frequency Reading Gain Factor 3m - Peak at 3m Margin zation (MHz) (dBμV) (dB) (dB) (dBμV/m) (dBμV/m) (dB) V 2441.000 103.2 33 29.4 99.6 114.0 -14.4 H 4882.000 44.0 33 34.9 45.9 74.0 -28.1 H 7323.000 43.4 33 37.9 48.3 74.0 -25.7 H 9764.000 42.3 33 40.4 49.7 74.0 -24.3 V 12205.000 45.0 33 40.5 52.5 74.0 -21.5 H 14646.000 48.0 33 38.4 53.4 74.0 -20.6 NOTES: 1. Peak Detector Data unless otherwise stated. 2. All measurements were made at 3 meters. Harmonic emissions not detected at the 3‐ meter distances were measured at 0.3‐meter and an inverse proportional extrapolation was performed to compare the signal level to the 3‐meter limit. No other harmonic emissions than those reported were detected at a test distance of 0.3‐meter. 3. Negative sign in the column shows value below limit. 4. Horn antenna is used for the emission over 1000MHz. (for Over 1GHz) 5. Emission (the row indicated by bold italic) within the restricted band meets the requirement of FCC Part 15 Section 15.205. 6. Measurement Uncertainty is ±5.3dB at a level of confidence of 95%. Page 11 of 20

Spin Master Toys Far East Ltd. Intertek Report No: 18080393HKG‐003 TEST REPORT Model: 66802 Date of Test: August 22, 2018 Worst‐Case Operating Mode: Transmitting Table 3 Pursuant to FCC Part 15 Section 15.249 Requirement Highest Channel Pre-Amp Antenna Net at Average Calculated Average Limit Polari- Frequency Reading Gain Factor 3m - Peak Factor at 3m at 3m Margin zation (MHz) (dBμV) (dB) (dB) (dBμV/m) (dB) (dBμV/m) (dBμV/m) (dB) V 2472.000 103.5 33 29.4 99.9 17.9 82.0 94.0 -12.0 V 2483.500 68.7 33 29.4 65.1 17.9 47.2 54.0 -6.8 H 4944.000 45.3 33 34.9 47.2 17.9 29.3 54.0 -24.7 V 7416.000 43.4 33 37.9 48.3 17.9 30.4 54.0 -23.6 H 9888.000 42.4 33 40.4 49.8 17.9 31.9 54.0 -22.1 H 12360.000 44.9 33 40.5 52.4 17.9 34.5 54.0 -19.5 H 14832.000 48.8 33 38.4 54.2 17.9 36.3 54.0 -17.7 Pre-Amp Antenna Net at Peak Limit Polari- Frequency Reading Gain Factor 3m - Peak at 3m Margin zation (MHz) (dBμV) (dB) (dB) (dBμV/m) (dBμV/m) (dB) V 2472.000 103.5 33 29.4 99.9 114.0 -14.1 V 2483.500 68.7 33 29.4 65.1 74.0 -8.9 H 4944.000 45.3 33 34.9 47.2 74.0 -26.8 V 7416.000 43.4 33 37.9 48.3 74.0 -25.7 H 9888.000 42.4 33 40.4 49.8 74.0 -24.2 H 12360.000 44.9 33 40.5 52.4 74.0 -21.6 H 14832.000 48.8 33 38.4 54.2 74.0 -19.8 NOTES: 1. Peak Detector Data unless otherwise stated. 2. All measurements were made at 3 meters. Harmonic emissions not detected at the 3‐ meter distances were measured at 0.3‐meter and an inverse proportional extrapolation was performed to compare the signal level to the 3‐meter limit. No other harmonic emissions than those reported were detected at a test distance of 0.3‐meter. 3. Negative sign in the column shows value below limit. 4. Horn antenna is used for the emission over 1000MHz. 5. Emission (the row indicated by bold italic) within the restricted band meets the requirement of FCC Part 15 Section 15.205. 6. Measurement Uncertainty is ±5.3dB at a level of confidence of 95%. Page 12 of 20

Spin Master Toys Far East Ltd. Intertek Report No: 18080393HKG‐003 TEST REPORT 4.0 EQUIPMENT PHOTOGRAPHS For electronic filing, the photographs are saved with filename: external photos.pdf and internal photos.pdf. 5.0 PRODUCT LABELLING For electronics filing, the FCC ID label artwork and the label location are saved with filename: label.pdf. 6.0 TECHNICAL SPECIFICATIONS For electronic filing, the block diagram and schematic of the tested EUT are saved with filename: block.pdf and circuit.pdf respectively. 7.0 INSTRUCTION MANUAL For electronic filing, a preliminary copy of the Instruction Manual is saved with filename: manual.pdf. This manual will be provided to the end‐user with each unit sold/leased in the United States. Page 13 of 20

Spin Master Toys Far East Ltd. Intertek Report No: 18080393HKG‐003 TEST REPORT 8.0 MISCELLANEOUS INFORMATION The miscellaneous information includes details of the test procedure and measured bandwidth / calculation of factor such as pulse desensitization and averaging factor (calculation and timing diagram). 8.1 Radiated Emission on the Bandedge The test data of bandedge emissions were shown on the above radiated emissions table 1 & table 3 respectively. Emissions radiated outside of the specified frequency bands, except harmonics, are attenuated by 50dB below the level of the fundamental or to the general radiated emissions limits in Section 15.209 , whichever is the lesser attenuation, which meet the requirement of part 15.249(d). Page 14 of 20

Spin Master Toys Far East Ltd. Intertek Report No: 18080393HKG‐003 TEST REPORT 8.2 Discussion of Pulse Desensitization Pulse desensitivity is not applicable for this device. The effective period (Teff) is approximately 0.975ms for a digital “1” bit which illustrated on technical specification, with a resolution bandwidth (3dB) of 1MHz, so the pulse desensitivity factor is 0dB. 8.3 Calculation of Average Factor The duty cycle is simply the on‐time divided by the period: The duration of one cycle = 100 ms Effective period of the cycle = 13*0.975 = 12.675 ms DC = 12.675/100 = 0.12675 Therefore, the averaging factor is found by 20log 0.012675 = ‐17.9dB. Page 15 of 20

Spin Master Toys Far East Ltd. Intertek Report No: 18080393HKG‐003 TEST REPORT AVERAGE FACTOR RBW 3 MHz VBW 10 MHz Ref -20 dBm * Att 10 dB SWT 100 ms -20 A -30 SGL 1 AP CLRWR TRG -40 TRG -41.6 dBm -50 PS -60 -70 3DB -80 AC -90 -100 -110 -120 Center 2.472 GHz 10 ms/ RBW 3 MHz Marker 1 [T1 ] VBW 10 MHz -32.47 dBm Ref -20 dBm * Att 10 dB SWT 2.5 ms 975.000000 µs -20 1 A -30 SGL 1 AP CLRWR TRG -40 TRG -41.6 dBm -50 PS -60 -70 3DB -80 AC -90 -100 -110 -120 Center 2.472 GHz 250 µs/ Page 16 of 20

Spin Master Toys Far East Ltd. Intertek Report No: 18080393HKG‐003 TEST REPORT 8.4 Emissions Test Procedures The following is a description of the test procedure used by Intertek Testing Services Hong Kong Ltd. in the measurements of transmitter operating under the Part 15, Subpart C rules. The transmitting equipment under test (EUT) is placed on a wooden turntable which is four feet in diameter and approximately 0.8m in height above the ground plane for emission measurement at or below 1GHz and 1.5m in height above the ground plane for emission measurement above 1GHz. During the radiated emissions test, the turntable is rotated and any cables leaving the EUT are manipulated to find the configuration resulting in maximum emissions. The EUT is adjusted through all three orthogonal axis to obtain maximum emission levels. The antenna height and polarization are also varied during the testing to search for maximum signal levels. The height of the antenna is varied from one to four meters. Detector function for radiated emissions is in peak mode. Average readings, when required, are taken by measuring the duty cycle of the equipment under test and subtracting the corresponding amount in dB from the measured peak readings. A detailed description for the calculation of the average factor can be found in Exhibit 8.3. The frequency range scanned is from the lowest radio frequency signal generated in the device which is greater than 9 kHz to the tenth harmonic of the highest fundamental frequency or 40 GHz, whichever is lower. Page 17 of 20

Spin Master Toys Far East Ltd. Intertek Report No: 18080393HKG‐003 TEST REPORT 8.4 Emissions Test Procedures (cont’d) The EUT is warmed up for 15 minutes prior to the test. AC power to the unit is varied from 85% to 115% nominal and variation in the fundamental emission field strength is recorded. If battery powered, a new, fully charged battery is used. Conducted measurements were made as described in ANSI C63.10 (2013). The IF bandwidth used for measurement of radiated signal strength was 100 kHz or greater when frequency is below 1000 MHz. Where pulsed transmissions of short enough pulse duration warrant, a greater bandwidth is selected according to the recommendations of Hewlett Packard Application Note 150‐2. A discussion of whether pulse desensitivity is applicable to this unit is included in this report (See Exhibit 8.1). Above 1000 MHz, a resolution bandwidth of 10 MHz is used. Transmitter measurements are normally conducted at a measurement distance of three meters. However, to assure low enough noise floor in the forbidden bands and above 1 GHz, signals are acquired at a distance of one meter or less. All measurements are extrapolated to three meters using inverse scaling, unless otherwise reported. Measurements taken at a closer distance are so marked. Page 18 of 20

Spin Master Toys Far East Ltd. Intertek Report No: 18080393HKG‐003 TEST REPORT 8.4.1 Radiated Emission Test Setup (For 1GHz Or Above) The figure below shows the test setup, which is utilized to make these measurements. Antenna 1.0~4.0m Tower 3m Receiver Antenna E U T 0.8m Ground Plane 3m Chamber □ RF Test Receiver Test setup of radiated emissions up to 1GHz Antenna 1.0~4.0m Tower 3m Receiver E Antenna U T 1.5m Ground Plane □ RF Test Spectrum Analyzer Test setup of radiated emissions above 1GHz Page 19 of 20

Spin Master Toys Far East Ltd. Intertek Report No: 18080393HKG‐003 TEST REPORT 9.0 EQUIPMENT LIST 1) Radiated Emissions Test Equipment EMI Test Receiver Spectrum Analyzer Biconical Antenna Registration No. EW‐3156 EW‐2329 EW‐0571 Manufacturer ROHDESCHWARZ ROHDESCHWARZ EMCO Model No. ESR26 FSP7 3104C Calibration Date November 10, 2017 September 28, 2017 February 27, 2018 Calibration Due Date November 10, 2018 September 28, 2018 August 27, 2019 Equipment Log Periodic Antenna Double Ridged Guide 14m Double Shield RF Antenna Cable (20MHz ‐ 6GHz) Registration No. EW‐1042 EW‐1133 EW‐2505 Manufacturer EMCO EMCO RADIALL Model No. 3148 3115 nm / br5d / sma 14m Calibration Date June 19, 2017 May 24, 2017 October 30, 2017 Calibration Due Date December 19, 2018 November 24, 2018 October 30, 2018 Equipment RF Cable 14m (1GHz to Solid State Low Noise RF Pre‐amplifier 3 pcs 26.5GHz) Preamplifier Assembly (9kHz to 40GHz) (1 ‐ 18)GHz Registration No. EW‐2781 EW‐3229 EW‐3006 Manufacturer GREATBILLION BONN ELEKTRO SCHWARZBECK Model No. SMA m/SHF5MPU /SMA BBV 9718 BLMA 0118‐5G m ra14m,26G Calibration Date September 25, 2017 January 30, 2018 April 26, 2018 Calibration Due Date September 25, 2018 January 30, 2019 April 26, 2019 2) Average Factor Measurement Equipment Spectrum Analyzer Registration No. EW‐2329 Manufacturer R&S Model No. FSP3 Calibration Date September 28, 2017 Calibration Due Date September 28, 2018 END OF TEST REPORT Page 20 of 20


Document Created: 2018-09-06 14:51:48
Document Modified: 2018-09-06 14:51:48
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC