Test Report

FCC ID: PQN44583BTX2G4

Test Report

Download: PDF
FCCID_3174543

TEST REPORT Report No.: 16041838HKG-001R1 Spin Master Toys Far East Ltd. Application For Certification (Original Grant) (FCC ID: PQN44583BTX2G4) Transceiver This report supersedes previous report with report number 16041838HKG-001 dated July 06, 2016. Prepared and Checked by: Approved by: Digitally signed by Kenneth Wong Location: Intertek Testing Services Hong Kong Ltd. Signed On File Leung Sung Tak, Andy Wong Kwok Yeung, Kenneth Assistant Engineer Senior Lead Engineer Date: October 25, 2016 - Intertek's standard Terms and Conditions can be obtained at our website http://www.intertek.com/terms/. - The test report only allows to be revised within the retention period unless further standard or the requirement was noticed. - This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. - © 2016 Intertek Intertek Testing Services Hong Kong Ltd. 2/F., Garment Centre, 576 Castle Peak Road, Kowloon, Hong Kong. Tel: (852) 2173 8888 Fax: (852) 2785 5487 Website: www.hk.intertek-etlsemko.com

INTERTEK TESTING SERVICES GENERAL INFORMATION Grantee: Spin Master Toys Far East Ltd. Grantee Address: Room 1113, 11/F, Chinachem Golden Plaza, 77 Mody Road, Tsim Sha Tsui East, Kowloon, Hong Kong. Contact Person: Andy Wong Tel: 0769-81080068-1123 Fax: N/A e-mail: andyw@spinmaster.com Manufacturer: Spin Master Toys Far East Ltd. Manufacturer Address: Room 1113, 11/F, Chinachem Golden Plaza, 77 Mody Road, Tsim Sha Tsui East, Kowloon, Hong Kong. Brand Name: ARH Model: 44583-0002 (1039775) Additional Model: 44593-0001 (1039774) Phantom No.: 20076356/20076355 Type of EUT: Transceiver Description of EUT: ARH RDC SW MicroQTieFightr ARH RDC SWMQ2PkBtTievsXwin( Xwing + Tie fighter) Serial Number: N/A FCC ID: PQN44583BTX2G4 Date of Sample Submitted: April 27, 2016 Date of Test: April 27, 2016 to May 21, 2016 Report No.: 16041838HKG-001R1 Report Date: October 25, 2016 Environmental Conditions: Temperature: +10 to 40°C Humidity: 10 to 90% Report No.: 16041838HKG-001R1 i FCC ID: PQN44583BTX2G4

INTERTEK TESTING SERVICES SUMMARY OF TEST RESULT TEST SPECIFICATION REFERENCE RESULTS Radiated Emission 15.249, 15.209 Pass Radiated Emission on the Bandedge Radiated Emission in Restricted Bands 15.205 Pass The equipment under test is found to be complying with the following standards: FCC Part 15, October 1, 2014 Edition Note: 1. The EUT uses a permanently attached antenna which, in accordance to section 15.203, is considered sufficient to comply with the pervisions of this section. 2. Pursuant to FCC part 15 Section 15.215(c), the 20 dB bandwidth of the emission was contained within the frequency band designated (mentioned as above) which the EUT operated. The effects, if any, from frequency sweeping, frequency hopping, other modulation techniques and frequency stability over excepted variations in temperature and supply voltage were considered. 3. Please refer TY-S16-0266 Letter issued on October 05, 2016 for amendment/ supersede notification. Report No.: 16041838HKG-001R1 ii FCC ID: PQN44583BTX2G4

INTERTEK TESTING SERVICES Table of Contents 1.0 General Description .............................................................................................. 1 1.1 Product Description ............................................................................................. 1 1.2 Related Submittal(s) Grants................................................................................. 1 1.3 Test Methodology ................................................................................................ 1 1.4 Test Facility ......................................................................................................... 1 2.0 System Test Configuration................................................................................... 2 2.1 Justification .......................................................................................................... 2 2.2 EUT Exercising Software ..................................................................................... 2 2.3 Special Accessories ............................................................................................ 2 2.4 Measurement Uncertainty.................................................................................... 2 2.5 Support Equipment List and Description .............................................................. 2 3.0 Emission Results .................................................................................................. 3 3.1 Field Strength Calculation .................................................................................... 3 3.2 Radiated Emission Configuration Photograph ..................................................... 4 3.3 Radiated Emission Data ...................................................................................... 4 4.0 Equipment Photographs....................................................................................... 9 5.0 Product Labelling .................................................................................................. 9 6.0 Technical Specifications ...................................................................................... 9 7.0 Instruction Manual ................................................................................................ 9 8.0 Miscellaneous Information ................................................................................. 10 8.1 Measured Bandwidth / Radiated Emission on the Bandedge ............................ 10 8.2 Discussion of Pulse Desensitization .................................................................. 11 8.3 Calculation of Average Factor............................................................................ 11 8.4 Emissions Test Procedures ............................................................................... 13 9.0 Equipment List .................................................................................................... 16 Report No.: 16041838HKG-001R1 iii FCC ID: PQN44583BTX2G4

INTERTEK TESTING SERVICES 1.0 General Description 1.1 Product Description The Equipment Under Test (EUT) is a portable 2.4GHz Transceiver (Controller Unit) for a RC plane operating at the frequency range of 2412-2470MHz with 2 MHz channel spacing. The EUT is powered by 6 * 1.5V AA batteries. After switch on the EUT and paired with plane, the plane can be controlled to move forward/backward and turn left/ right by the controller. The Model: 44593-0001 (1039774) is the same as the Model: 44583-0002 (1039775) in hardware aspect. The models are different in model number only. Antenna Type: Internal, Integral For electronic filing, the brief circuit description is saved with filename: descri.pdf. 1.2 Related Submittal(s) Grants This is a single application for certification of a transceiver. The Certification procedure of the plane for this controller (with FCC ID:PQN44583BRX2G4) is being processed as the same time of this application. 1.3 Test Methodology Radiated emission measurements was performed according to the procedures in ANSI C63.10 (2013). All radiated measurements were performed in an 3m Chamber. Preliminary scans were performed in the 3m Chamber only to determine worst case modes. All radiated tests were performed at an antenna to EUT distance of 3 meters, unless stated otherwise in the “Justification Section” of this Application. 1.4 Test Facility The 3m Chamber facility used to collect the radiated data is located at Workshop No. 3, G/F., World-Wide Industrial Centre, 43-47 Shan Mei Street, Fo Tan, Sha Tin, N.T., Hong Kong. This test facility and site measurement data have been placed on file with the FCC. Report No.: 16041838HKG-001R1 1 of 16 FCC ID: PQN44583BTX2G4

INTERTEK TESTING SERVICES 2.0 System Test Configuration 2.1 Justification The system was configured for testing in a typical fashion (as a customer would normally use it), and in the confines as outlined in ANSI C63.10 (2013). The device was powered by new 6 * 1.5V AA batteries. For maximizing emissions, the EUT was rotated through 360°, the antenna height was varied from 1 meter to 4 meters above the ground plane, and the antenna polarization was changed. This step by step procedure for maximizing emissions led to the data reported in Exhibit 3.0. The unit was operated standalone and placed in the center of the turntable. The equipment under test (EUT) was configured for testing in a typical fashion (as a customer would normally use it). The EUT was mounted to a plastic stand if necessary and placed on the wooden turntable, which enabled the engineer to maximize emissions through its placement in the three orthogonal axes. 2.2 EUT Exercising Software There was no special software to exercise the device. Once the unit is powered up, it transmits the RF signal continuously. 2.3 Special Accessories There are no special accessories necessary for compliance of this product. 2.4 Measurement Uncertainty When determining of the test conclusion, the Measurement Uncertainty of test has been considered. 2.5 Support Equipment List and Description N/A. Report No.: 16041838HKG-001R1 2 of 16 FCC ID: PQN44583BTX2G4

INTERTEK TESTING SERVICES 3.0 Emission Results Data is included of the worst case configuration (the configuration which resulted in the highest emission levels). A sample calculation, configuration photographs and data tables of the emissions are included. 3.1 Field Strength Calculation The field strength is calculated by adding the Antenna Factor and Cable Factor, and subtracting the Amplifier Gain (if any), Average Factor (optional) from the measured reading. The basic equation with a sample calculation is as follows: FS = RA + AF + CF - AG - AV where FS = Field Strength in dBµV/m RA = Receiver Amplitude (including preamplifier) in dBµV CF = Cable Attenuation Factor in dB AF = Antenna Factor in dB AG = Amplifier Gain in dB AV = Average Factor in dB In the following table(s), the reading shown on the data table reflects the preamplifier gain. An example for the calculations in the following table is as follows: FS = RR + LF where FS = Field Strength in dBµV/m RR = RA - AG - AV in dBµV LF = CF + AF in dB Assume a receiver reading of 52.0 dBµV is obtained. The antenna factor of 7.4 dB and cable factor of 1.6 dB are added. The amplifier gain of 29 dB and average factor of 5 dB are subtracted, giving a field strength of 27 dBµV/m. This value in dBµV/m was converted to its corresponding level in µV/m. RA = 52.0 dBµV/m AF = 7.4 dB RR = 18.0 dBµV CF = 1.6 dB LF = 9.0 dB AG = 29.0 dB AV = 5.0 dB FS = RR + LF FS = 18 + 9 = 27 dBµV/m Level in µV/m = Common Antilogarithm [(27 dBµV/m)/20] = 22.4 µV/m Report No.: 16041838HKG-001R1 3 of 16 FCC ID: PQN44583BTX2G4

INTERTEK TESTING SERVICES 3.2 Radiated Emission Configuration Photograph The worst case in radiated emission was found at 7236 MHz For electronic filing, the worst case radiated emission configuration photographs are saved with filename: radiated photos.pdf. 3.3 Radiated Emission Data The data on the following page lists the significant emission frequencies, the limit and the margin of compliance. Numbers with a minus sign are below the limit. Judgment: Passed by 10.9 dB Report No.: 16041838HKG-001R1 4 of 16 FCC ID: PQN44583BTX2G4

INTERTEK TESTING SERVICES Applicant: Spin Master Toys Far East Ltd. Date of Test: May 21, 2016 Model: 44583-0002 (1039775) Worst-Case Operating Mode: Transmitting Table 1 Radiated Emissions Pursuant to FCC Part 15 Section 15.249 Requirement Lowest Channel Pre-Amp Antenna Net at Average Calculated Average Limit Polari- Frequency Reading Gain Factor 3m - Peak Factor at 3m at 3m Margin zation (MHz) (dBμV) (dB) (dB) (dBμV/m) (dB) (dBμV/m) (dBμV/m) (dB) V 2412.000 82.5 33 29.4 78.9 25.7 53.2 94.0 -40.8 V 2400.000 61.8 33 29.4 58.2 25.7 32.5 54.0 -21.5 V 4824.000 53.4 33 34.9 55.3 25.7 29.6 54.0 -24.4 H 7236.000 58.2 33 37.9 63.1 25.7 37.4 54.0 -16.6 H 9648.000 41.7 33 40.4 49.1 25.7 23.4 54.0 -30.6 H 12060.000 43.4 33 40.5 50.9 25.7 25.2 54.0 -28.8 H 14472.000 45.1 33 40.0 52.1 25.7 26.4 54.0 -27.6 Pre-Amp Antenna Net at Peak Limit Polari- Frequency Reading Gain Factor 3m - Peak at 3m Margin zation (MHz) (dBμV) (dB) (dB) (dBμV/m) (dBμV/m) (dB) V 2412.000 82.5 33 29.4 78.9 114.0 -35.1 V 2400.000 61.8 33 29.4 58.2 74.0 -15.8 V 4824.000 53.4 33 34.9 55.3 74.0 -18.7 H 7236.000 58.2 33 37.9 63.1 74.0 -10.9 H 9648.000 41.7 33 40.4 49.1 74.0 -24.9 H 12060.000 43.4 33 40.5 50.9 74.0 -23.1 H 14472.000 45.1 33 40.0 52.1 74.0 -21.9 NOTES: 1. Peak Detector Data unless otherwise stated. 2. All measurements were made at 3 meters. Harmonic emissions not detected at the 3-meter distances were measured at 0.3-meter and an inverse proportional extrapolation was performed to compare the signal level to the 3-meter limit. No other harmonic emissions than those reported were detected at a test distance of 0.3-meter. 3. Negative sign in the column shows value below limit. 4. Horn antenna is used for the emission over 1000MHz. 5. Emission (the row indicated by bold italic) within the restricted band meets the requirement of FCC Part 15 Section 15.205. 6. Measurement Uncertainty is ±5.3dB at a level of confidence of 95%. Report No.: 16041838HKG-001R1 5 of 16 FCC ID: PQN44583BTX2G4

INTERTEK TESTING SERVICES Applicant: Spin Master Toys Far East Ltd. Date of Test: May 21, 2016 Model: 44583-0002 (1039775) Worst-Case Operating Mode: Transmitting Table 2 Radiated Emissions Pursuant to FCC Part 15 Section 15.249 Requirement Middle Channel Pre-Amp Antenna Net at Average Calculated Average Limit Polari- Frequency Reading Gain Factor 3m - Peak Factor at 3m at 3m Margin zation (MHz) (dBμV) (dB) (dB) (dBμV/m) (dB) (dBμV/m) (dBμV/m) (dB) V 2442.000 82.9 33 29.4 79.3 25.7 53.6 94.0 -40.4 V 4884.000 51.9 33 34.9 53.8 25.7 28.1 54.0 -25.9 H 7326.000 57.6 33 37.9 62.5 25.7 36.8 54.0 -17.2 H 9768.000 41.6 33 40.4 49.0 25.7 23.3 54.0 -30.7 H 12210.000 43.7 33 40.5 51.2 25.7 25.5 54.0 -28.5 H 14652.000 46.8 33 38.4 52.2 25.7 26.5 54.0 -27.5 Pre-Amp Antenna Net at Peak Limit Polari- Frequency Reading Gain Factor 3m - Peak at 3m Margin zation (MHz) (dBμV) (dB) (dB) (dBμV/m) (dBμV/m) (dB) V 2442.000 82.9 33 29.4 79.3 114.0 -34.7 V 4884.000 51.9 33 34.9 53.8 74.0 -20.2 H 7326.000 57.6 33 37.9 62.5 74.0 -11.5 H 9768.000 41.6 33 40.4 49.0 74.0 -25.0 H 12210.000 43.7 33 40.5 51.2 74.0 -22.8 H 14652.000 46.8 33 38.4 52.2 74.0 -21.8 NOTES: 1. Peak Detector Data unless otherwise stated. 2. All measurements were made at 3 meters. Harmonic emissions not detected at the 3-meter distances were measured at 0.3-meter and an inverse proportional extrapolation was performed to compare the signal level to the 3-meter limit. No other harmonic emissions than those reported were detected at a test distance of 0.3-meter. 3. Negative sign in the column shows value below limit. 4. Horn antenna is used for the emission over 1000MHz. 5. Emission (the row indicated by bold italic) within the restricted band meets the requirement of FCC Part 15 Section 15.205. 6. Measurement Uncertainty is ±5.3dB at a level of confidence of 95%. Report No.: 16041838HKG-001R1 6 of 16 FCC ID: PQN44583BTX2G4

INTERTEK TESTING SERVICES Applicant: Spin Master Toys Far East Ltd. Date of Test: May 21, 2016 Model: 44583-0002 (1039775) Worst-Case Operating Mode: Transmitting Table 3 Radiated Emissions Pursuant to FCC Part 15 Section 15.249 Requirement Highest Channel Pre-Amp Antenna Net at Average Calculated Average Limit Polari- Frequency Reading Gain Factor 3m - Peak Factor at 3m at 3m Margin zation (MHz) (dBμV) (dB) (dB) (dBμV/m) (dB) (dBμV/m) (dBμV/m) (dB) V 2470.000 83.6 33 29.4 80.0 25.7 54.3 94.0 -39.7 V 2483.500 62.9 33 29.4 59.3 25.7 33.6 54.0 -20.4 V 4940.000 52.4 33 34.9 54.3 25.7 28.6 54.0 -25.4 H 7410.000 56.9 33 37.9 61.8 25.7 36.1 54.0 -17.9 H 9880.000 41.4 33 40.4 48.8 25.7 23.1 54.0 -30.9 H 12350.000 43.6 33 40.5 51.1 25.7 25.4 54.0 -28.6 H 14820.000 47.0 33 38.4 52.4 25.7 26.7 54.0 -27.3 Pre-Amp Antenna Net at Peak Limit Polari- Frequency Reading Gain Factor 3m - Peak at 3m Margin zation (MHz) (dBμV) (dB) (dB) (dBμV/m) (dBμV/m) (dB) V 2470.000 83.6 33 29.4 80.0 114.0 -34.0 V 2483.500 62.9 33 29.4 59.3 74.0 -14.7 V 4940.000 52.4 33 34.9 54.3 74.0 -19.7 H 7410.000 56.9 33 37.9 61.8 74.0 -12.2 H 9880.000 41.4 33 40.4 48.8 74.0 -25.2 H 12350.000 43.6 33 40.5 51.1 74.0 -22.9 H 14820.000 47.0 33 38.4 52.4 74.0 -21.6 NOTES: 1. Peak Detector Data unless otherwise stated. 2. All measurements were made at 3 meters. Harmonic emissions not detected at the 3-meter distances were measured at 0.3-meter and an inverse proportional extrapolation was performed to compare the signal level to the 3-meter limit. No other harmonic emissions than those reported were detected at a test distance of 0.3-meter. 3. Negative sign in the column shows value below limit. 4. Horn antenna is used for the emission over 1000MHz. 5. Emission (the row indicated by bold italic) within the restricted band meets the requirement of FCC Part 15 Section 15.205. 6. Measurement Uncertainty is ±5.3dB at a level of confidence of 95%. Report No.: 16041838HKG-001R1 7 of 16 FCC ID: PQN44583BTX2G4

INTERTEK TESTING SERVICES Applicant: Spin Master Toys Far East Ltd. Date of Test: May 21, 2016 Model: 44583-0002 (1039775) Worst-Case Operating Mode: Transmitting Table 4 Radiated Emissions Pursuant to FCC Part 15 Section 15.209 Requirement Pre- Antenna Net Limit Frequency Reading amp Factor at 3m at 3m Margin Polarization (MHz) (dBμV) (dB) (dB) (dBμV/m) (dBμV/m) (dB) V 263.947 15.4 16 21.0 20.4 46.0 -25.6 V 300.674 21.0 16 22.0 27.0 46.0 -19.0 H 539.758 11.5 16 28.0 23.5 46.0 -22.5 V 1415.175 37.4 33 26.1 30.5 54.0 -23.5 H 2108.328 37.7 33 29.4 34.1 54.0 -19.9 H 3296.475 40.3 33 31.9 39.2 54.0 -14.8 NOTES: 1. Peak Detector Data unless otherwise stated. 2. All measurements were made at 3 meters. Harmonic emissions not detected at the 3-meter distances were measured at 0.3-meter and an inverse proportional extrapolation was performed to compare the signal level to the 3-meter limit. No other harmonic emissions than those reported were detected at a test distance of 0.3-meter. 3. Negative sign in the column shows value below limit. 4. Horn antenna is used for the emission over 1000MHz. 5. Emission (the row indicated by bold italic) within the restricted band meets the requirement of FCC Part 15 Section 15.205. 6. Measurement Uncertainty is ±5.3dB at a level of confidence of 95%. Report No.: 16041838HKG-001R1 8 of 16 FCC ID: PQN44583BTX2G4

INTERTEK TESTING SERVICES 4.0 Equipment Photographs For electronic filing, the photographs are saved with filename: external photos.pdf and internal photos.pdf. 5.0 Product Labelling For electronics filing, the FCC ID label artwork and the label location are saved with filename: label.pdf. 6.0 Technical Specifications For electronic filing, the block diagram and schematic of the tested EUT are saved with filename: block.pdf and circuit.pdf respectively. 7.0 Instruction Manual For electronic filing, a preliminary copy of the Instruction Manual is saved with filename: manual.pdf. This manual will be provided to the end-user with each unit sold/leased in the United States. Report No.: 16041838HKG-001R1 9 of 16 FCC ID: PQN44583BTX2G4

INTERTEK TESTING SERVICES 8.0 Miscellaneous Information The miscellaneous information includes details of the test procedure and measured bandwidth / calculation of factor such as pulse desensitization and averaging factor (calculation and timing diagram). 8.1 Radiated Emission on the Bandedge The test data of bandedge emissions were shown on the above radiated emissions table 1 & table 3 respectively. Emissions radiated outside of the specified frequency bands, except harmonics, are attenuated by 50dB below the level of the fundamental or to the general radiated emissions limits in Section 15.209, whichever is the lesser attenuation, which meet the requirement of part 15.249(d). The resultant field strength meets the general radiated emission limit in Section 15.209, which does not exceed 74 dBµV/m (Peak Limit) and 54 dBµV/m (Average Limit). Report No.: 16041838HKG-001R1 10 of 16 FCC ID: PQN44583BTX2G4

INTERTEK TESTING SERVICES 8.2 Discussion of Pulse Desensitization Pulse desensitivity is not applicable for this device. The effective period (Teff) is approximately 744 µs for a digital “1” bit which illustrated on technical specification, with a resolution bandwidth (3dB) of 1MHz, so the pulse desensitivity factor is 0dB. 8.3 Calculation of Average Factor The duty cycle is simply the on-time divided by the period: The duration of one cycle = 100ms Effective period of the cycle = 7*0.744 = 5.208ms DC = 5.208/100 = 0.05208ms Therefore, the averaging factor is found by 20log 0.05208 = -25.7dB. Report No.: 16041838HKG-001R1 11 of 16 FCC ID: PQN44583BTX2G4

INTERTEK TESTING SERVICES Average Factor RBW 3 MHz Marker 1 [T1 ] VBW 10 MHz -44.88 dBm Ref -30 dBm * Att 10 dB SWT 1 ms 744.000000 µs -30 A -40 1 SGL 1 PK MAXH TRG -50 -60 PS TRG -68.4 dBm -70 -80 3DB -90 AC -100 -110 -120 -130 Center 2.452605 GHz 100 µs/ RBW 3 MHz VBW 10 MHz Ref -30 dBm * Att 10 dB SWT 100 ms -30 A -40 SGL 1 PK MAXH TRG -50 TRG -56.6 dBm -60 PS -70 -80 3DB -90 AC -100 -110 -120 -130 Center 2.452605 GHz 10 ms/ Report No.: 16041838HKG-001R1 12 of 16 FCC ID: PQN44583BTX2G4

INTERTEK TESTING SERVICES 8.4 Emissions Test Procedures The following is a description of the test procedure used by Intertek Testing Services Hong Kong Ltd. in the measurements of transmitter operating under the Part 15, Subpart C rules. The transmitting equipment under test (EUT) is placed on a wooden turntable which is four feet in diameter and approximately 0.8m in height above the ground plane for emission measurement at or below 1GHz and 1.5m in height above the ground plane for emission measurement above 1GHz. During the radiated emissions test, the turntable is rotated and any cables leaving the EUT are manipulated to find the configuration resulting in maximum emissions. The EUT is adjusted through all three orthogonal axis to obtain maximum emission levels. The antenna height and polarization are also varied during the testing to search for maximum signal levels. The height of the antenna is varied from one to four meters. Detector function for radiated emissions is in peak mode. Average readings, when required, are taken by measuring the duty cycle of the equipment under test and subtracting the corresponding amount in dB from the measured peak readings. A detailed description for the calculation of the average factor can be found in Exhibit 8.3. The frequency range scanned is from the lowest radio frequency signal generated in the device which is greater than 9 kHz to the tenth harmonic of the highest fundamental frequency or 40 GHz, whichever is lower. Report No.: 16041838HKG-001R1 13 of 16 FCC ID: PQN44583BTX2G4

INTERTEK TESTING SERVICES 8.4 Emissions Test Procedures (cont’d) The EUT is warmed up for 15 minutes prior to the test. AC power to the unit is varied from 85% to 115% nominal and variation in the fundamental emission field strength is recorded. If battery powered, a new, fully charged battery is used. Conducted measurements were made as described in ANSI C63.10 (2013). The IF bandwidth used for measurement of radiated signal strength was 100 kHz or greater when frequency is below 1000 MHz. Where pulsed transmissions of short enough pulse duration warrant, a greater bandwidth is selected according to the recommendations of Hewlett Packard Application Note 150-2. A discussion of whether pulse desensitivity is applicable to this unit is included in this report (See Exhibit 8.1). Above 1000 MHz, a resolution bandwidth of 3 MHz is used. Transmitter measurements are normally conducted at a measurement distance of three meters. However, to assure low enough noise floor in the forbidden bands and above 1 GHz, signals are acquired at a distance of one meter or less. All measurements are extrapolated to three meters using inverse scaling, unless otherwise reported. Measurements taken at a closer distance are so marked. Report No.: 16041838HKG-001R1 14 of 16 FCC ID: PQN44583BTX2G4

INTERTEK TESTING SERVICES 8.4.1 Radiated Emission Test Setup The figure below shows the test setup, which is utilized to make these measurements. Antenna 1.0~4.0m Tower 3m Receiver Antenna E U T 0.8m Ground Plane 3m Chamber □ RF Test Receiver Test setup of radiated emissions up to 1GHz Antenna 1.0~4.0m Tower 3m Receiver E Antenna U T 1.5m Ground Plane □ RF Test Spectrum Analyzer Test setup of radiated emissions above 1GHz Report No.: 16041838HKG-001R1 15 of 16 FCC ID: PQN44583BTX2G4

INTERTEK TESTING SERVICES 9.0 Equipment List 1) Radiated Emissions Test Equipment EMI Test Receiver BiConical Antenna Registration No. EW-3156 EW-0571 Manufacturer R&S EMCO Model No. ESR26 3104C Calibration Date Nov. 03, 2015 Jun. 23, 2015 Calibration Due Date Nov. 03, 2016 Dec. 23, 2016 Equipment Double Ridged Guide Log Periodic Antenna Antenna Registration No. EW-1133 EW-0572 Manufacturer EMCO EMCO Model No. 3115 3146 Calibration Date Nov. 05, 2015 Jan.19, 2015 Calibration Due Date May 05, 2017 Jul. 19, 2016 2) Average Factor & OBW Measurement Equipment Spectrum Analyzer Registration No. EW-2329 Manufacturer R&S Model No. FSP3 Calibration Date Jun. 17, 2015 Calibration Due Date Jun. 17, 2016 END OF TEST REPORT Report No.: 16041838HKG-001R1 16 of 16 FCC ID: PQN44583BTX2G4


Document Created: 2016-10-25 09:54:39
Document Modified: 2016-10-25 09:54:39
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC