Test Report

FCC ID: PQN44519TX2G4

Test Report

Download: PDF
FCCID_3197710

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch. No. 1 Workshop, M-10, Middle section, Science & Technology Park, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Report No.: SZEM160900821203 Email: ee.shenzhen@sgs.com Page: 1 of 31 1 Cover page FCC REPORT Application No. : SZEM1609008212CR (SGS SZ No.:T51610250108EM) Applicant: SpinMaster Toys Far East LTD. Manufacturer: SpinMaster Toys Far East LTD. Product Name: AIR HOGS EJECTOR JET Item No.(EUT): 44519TX Brand Name: ARH FCC ID: PQN44519TX2G4 Standards: 47 CFR Part 15, Subpart C (2015) Date of Receipt: 2016-09-26 Date of Test: 2016-10-08 to 2016-10-09 Date of Issue: 2016-10-11 Test Result: PASS * . * In the configuration tested, the EUT complied with the standards specified above. Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch. Report No.: SZEM160900821203 Page : 2 of 31 2 Version Revision Record Version Chapter Date Modifier Remark 00 2016-10-11 Original Authorized for issue by: Tested By 2016-10-09 (Gebin Sun) /Project Engineer Date Checked By 2016-10-11 (Eric Fu) /Reviewer Date This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch. Report No.: SZEM160900821203 Page : 3 of 31 3 Test Summary Test Item Test Requirement Test method Result 47 CFR Part 15, Subpart C Section Antenna Requirement ANSI C63.10 (2013) PASS 15.203 AC Power Line 47 CFR Part 15, Subpart C Section ANSI C63.10 (2013) PASS Conducted Emission 15.207 Field Strength of the 47 CFR Part 15, Subpart C Section ANSI C63.10 (2013) PASS Fundamental Signal 15.249 (a) 47 CFR Part 15, Subpart C Section Spurious Emissions ANSI C63.10 (2013) PASS 15.249 (a)/15.209 Restricted bands around fundamental 47 CFR Part 15, Subpart C Section ANSI C63.10 (2013) PASS frequency (Radiated 15.249(a)/15.205 Emission) 20dB Occupied 47 CFR Part 15, Subpart C Section ANSI C63.10 (2013) PASS Bandwidth 15.215 (c) This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch. Report No.: SZEM160900821203 Page : 4 of 31 4 Contents Page 1 COVER PAGE.........................................................................................................................................................1 2 VERSION .................................................................................................................................................................2 3 TEST SUMMARY ...................................................................................................................................................3 4 CONTENTS .............................................................................................................................................................4 5 GENERAL INFORMATION...................................................................................................................................5 5.1 CLIENT INFORMATION ...........................................................................................................................................5 5.2 GENERAL DESCRIPTION OF EUT ............................................................................................................................5 5.3 TEST ENVIRONMENT AND MODE ...........................................................................................................................7 5.4 DESCRIPTION OF SUPPORT UNITS...........................................................................................................................7 5.5 TEST LOCATION .....................................................................................................................................................7 5.6 TEST FACILITY .......................................................................................................................................................8 5.7 DEVIATION FROM STANDARDS ..............................................................................................................................8 5.8 ABNORMALITIES FROM STANDARD CONDITIONS ...................................................................................................8 5.9 OTHER INFORMATION REQUESTED BY THE CUSTOMER .........................................................................................8 5.10 EQUIPMENT LIST ...............................................................................................................................................9 6 TEST RESULTS AND MEASUREMENT DATA..............................................................................................11 6.1 ANTENNA REQUIREMENT ....................................................................................................................................11 6.2 RADIATED SPURIOUS EMISSIONS .........................................................................................................................12 6.2.1 Spurious Emissions ................................................................................................................................12 6.3 RESTRICTED BANDS AROUND FUNDAMENTAL FREQUENCY ..................................................................................20 6.4 20DB BANDWIDTH ..............................................................................................................................................28 7 PHOTOGRAPHS ..................................................................................................................................................31 7.1 RADIATED EMISSION TEST SETUP ........................................................................................................................31 7.2 EUT CONSTRUCTIONAL DETAILS ........................................................................................................................31 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch. Report No.: SZEM160900821203 Page : 5 of 31 5 General Information 5.1 Client Information Applicant: SpinMaster Toys Far East LTD. Address of Applicant: 1113, 11th Floor, Chinachen Golden Plaza, 77 Mody Road, Tsim Sha Tsui East, Kowloon, Hong Kong Manufacturer: SpinMaster Toys Far East LTD. 5.2 General Description of EUT Product Name: AIR HOGS EJECTOR JET Item No.: 44519TX Brand Name:: ARH Family No.: 44519 Request Age Grading: 8+ Date Code: 60915AWS Country of Origin: Made In China Country of Destination: US Frequency Range: 2.4GHz (2407 MHz ~ 2477MHz ) Modulation Type: GFSK Sample Type: Portable production Antenna Type: Integral Antenna Gain: 0dBi Power Supply: 9.0V DC(1.5V x 6 "AA" Size Batteries) for remote controller This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch. Report No.: SZEM160900821203 Page : 6 of 31 Operation Frequency each of channel Channel Frequency Channel Frequency Channel Frequency 1CH 2407 MHz 7CH 2435 MHz 16CH 2467 MHz 2CH 2408 MHz 8CH 2436 MHz 17CH 2468 MHz 3CH 2409 MHz 9CH 2438 MHz 18CH 2469 MHz 4CH 2410 MHz 10CH 2440 MHz 19CH 2470 MHz 5CH 2411 MHz 11CH 2441 MHz 20CH 2471 MHz 6CH 2413 MHz 12CH 2442 MHz 21CH 2472 MHz 13CH 2443 MHz 22CH 2473 MHz 14CH 2444 MHz 23CH 2474 MHz 15CH 2445 MHz 24CH 2475 MHz 25CH 2476 MHz 26CH 2477 MHz Note: In section 15.31(m), regards to the operating frequency range over 10 MHz, the Lowest frequency, the middle frequency, and the highest frequency of channel were selected to perform the test, and the selected channel see below: Channel Frequency The Lowest channel(CH1) 2407MHz The Middle channel(CH12) 2442MHz The Highest channel(CH26) 2477MHz This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch. Report No.: SZEM160900821203 Page : 7 of 31 5.3 Test Environment and Mode Operating Environment: Temperature: 25.0 °C Humidity: 50 % RH Atmospheric Pressure: 1005 mbar Test mode: Transmitting mode: Keep the EUT in transmitting mode with modulation. 5.4 Description of Support Units The EUT has been tested independently. 5.5 Test Location All tests were performed at: SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen Branch No. 1 Workshop, M-10, Middle Section, Science & Technology Park, Shenzhen, Guangdong, China. 518057. Tel: +86 755 2601 2053 Fax: +86 755 2671 0594 No tests were sub-contracted. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch. Report No.: SZEM160900821203 Page : 8 of 31 5.6 Test Facility The test facility is recognized, certified, or accredited by the following organizations: • CNAS (No. CNAS L2929) CNAS has accredited SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch EMC Lab to ISO/IEC 17025:2005 General Requirements for the Competence of Testing and Calibration Laboratories (CNAS-CL01 Accreditation Criteria for the Competence of Testing and Calibration Laboratories) for the competence in the field of testing. • A2LA (Certificate No. 3816.01) SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory is accredited by the American Association for Laboratory Accreditation(A2LA). Certificate No. 3816.01. • VCCI The 10m Semi-anechoic chamber and Shielded Room of SGS-CSTC Standards Technical Services Co., Ltd. have been registered in accordance with the Regulations for Voluntary Control Measures with Registration No.: G-823, R-4188, T-1153 and C-2383 respectively. • FCC – Registration No.: 556682 SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in our files. Registration No.: 556682. • Industry Canada (IC) Two 3m Semi-anechoic chambers and the 10m Semi-anechoic chamber of SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch EMC Lab have been registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 4620C-1, 4620C-2, 4620C-3. 5.7 Deviation from Standards None. 5.8 Abnormalities from Standard Conditions None. 5.9 Other Information Requested by the Customer None. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch. Report No.: SZEM160900821203 Page : 9 of 31 5.10 Equipment List RE in Chamber Cal.Due Inventory Cal. date Item Test Equipment Manufacturer Model No. date No. (yyyy-mm-dd) (yyyy-mm-dd) 3m Semi-Anechoic 1 ETS-LINDGREN N/A SEM001-01 2016-05-13 2017-05-13 Chamber Agilent 2 EMI Test Receiver N9038A SEM004-05 2016-10-09 2017-10-09 Technologies BiConiLog Antenna 3 ETS-LINDGREN 3142C SEM003-01 2014-11-01 2017-11-01 (26-3000MHz) Double-ridged horn 4 ETS-LINDGREN 3117 SEM003-11 2015-10-17 2018-10-17 (1-18GHz) Horn Antenna 5 ETS-LINDGREN 3160 SEM003-12 2014-11-24 2017-11-24 (18-26GHz) Pre-amplifier Agilent 6 8447D SEM005-01 2016-04-25 2017-04-25 (0.1-1300MHz) Technologies 7 Band filter Amindeon Asi 3314 SEM023-01 N/A N/A 8 DC Power Supply Zhao Xin RXN-305D SEM011-02 2016-10-09 2017-10-09 9 Loop Antenna Beijing Daze ZN30401 SEM003-09 2015-05-13 2018-05-13 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch. Report No.: SZEM160900821203 Page : 10 of 31 RE in Chamber Inventory Cal. date Cal.Due date Item Test Equipment Manufacturer Model No. No. (yyyy-mm-dd) (yyyy-mm-dd) 3m Semi-Anechoic 1 AUDIX N/A SEM001-02 2016-05-13 2017-05-13 Chamber 2 EMI Test Receiver Rohde & Schwarz ESIB26 SEM004-04 2016-04-25 2017-04-25 BiConiLog Antenna 3 ETS-Lindgren 3142C SEM003-02 2014-11-15 2017-11-15 (26-3000MHz) Amplifier 4 HP 8447D SEM005-02 2015-10-09 2016-10-09 (0.1-1300MHz) Horn Antenna 5 Rohde & Schwarz HF907 SEM003-07 2015-06-14 2018-06-14 (1-18GHz) Horn Antenna 6 ETS-Lindgren 3160 SEM003-12 2014-11-24 2017-11-24 (18-26GHz) Horn 7 Antenna(26GHz- A.H.Systems, inc. SAS-573 SEM003-13 2015-02-12 2018-02-12 40GHz) BDLNA- Black Diamond 8 Low Noise Amplifier 0118- SEM005-05 2015-10-09 2016-10-09 Series 352810 9 Band filter Amindeon Asi 3314 SEM023-01 N/A N/A RF connected test Cal. date Cal.Due date Item Test Equipment Manufacturer Model No. Inventory No. (yyyy-mm-dd) (yyyy-mm-dd) 1 DC Power Supply ZhaoXin RXN-305D SEM011-02 2015-10-09 2016-10-09 2 Spectrum Analyzer Rohde & Schwarz FSP SEM004-06 2015-10-17 2016-10-17 3 Signal Generator Rohde & Schwarz SML03 SEM006-02 2016-04-25 2017-04-25 4 Power Meter Rohde & Schwarz NRVS SEM014-02 2015-10-09 2016-10-09 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch. Report No.: SZEM160900821203 Page : 11 of 31 6 Test results and Measurement Data 6.1 Antenna Requirement Standard requirement: 47 CFR Part 15C Section 15.203 15.203 requirement: An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator, the manufacturer may design the unit so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited. EUT Antenna: The antenna is integrated on the main PCB and no consideration of replacement. The best case gain of the antenna is 0dBi. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS—CSTC Standards Technical Services Co., Ltd. Shenzhen Branch. Report No.: SZEM1608008z1203 Page 12 or 1 6.2. Rediated Spurious Emissions 6.2.1 Spurious Emissions Test Requrement: 47 OFR Part 150 Section 15.249 and 15.209 Test Methect Ant 0ss.10: 2ora Tes: Ste Measirement Disance: am (Gom Ancchoic Chamben Recaver Setup Frequency Detector new vew Remark o costiie—0 osotle Poak wodt _|_s00% Posk o.oostiiz—0.000tHe Average Toitle 30e _|__Average 0.090M4z—0.110blHe Quasipeak |__10dle_| 30e Quasipeak o rrou—0.4s00(e Poak it _|_s00% Posk 0.110M—0.4000He Average Toible 80e Average 0.490Nite —s0tlide Quasipeak 10e 30e _|_Quasipeak soubte—iGie Quasipeak |_tookile 8001612 |_Quasipeak Posk We auie Posk Above 1GHtz Posk We foge Average Umi Fied stengih mt Measuremont (Spurious Emisions) Frequency (mierovotimete (ailime y PEM®K arstance (m) 1 o. oomiiie0.as0vite |_22007F(ite) — — mo o.isoMe—1.7osvite 240007(ite) — — so 1.r0sMe—c0vite so — — so covi—coutte 100 40.0 Quasipent a sovir—zroNie is 425 Quasipeat a 2iotibe—acouile zoo 46.0 Quasipent a seouite—rGrte soo 540 Quasipeak a Above 1GHz soo 540 |_Average s Nete: 15.35(b, Unless othorvise spacifed, the im on peak redio frequency anissions is 204B above the maximum permited average emission Imapplcable to the equlpment undartest This peak limk applies to the total paak emision level radiated by te device Lmk Frequeney Limt (@Buim @@m) Rematk (Fd strengih ofthe mo Averege vaie tundementasignal) padoMite—asss shite mad Peak value Tes: Soup

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch. Report No.: SZEM160900821203 Page : 13 of 31 Figure 1. Below 30MHz Figure 2. 30MHz to 1GHz Figure 3. Above 1 GHz Test Procedure: a. For below 1GHz, the EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter semi-anechoic camber. The table was rotated 360 degrees to determine the position of the highest radiation. b. For above 1GHz, the EUT was placed on the top of a rotating table 1.5 meters above the ground at a 3 meter semi-anechoic camber. The table was rotated 360 degrees to determine the position of the highest radiation c. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. d. The antenna height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. e. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters (for the test frequency of below 30MHz, the antenna was tuned to heights 1 meter) and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. f. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. g. If the emission level of the EUT in peak mode was 10dB lower than the limit specified, then testing could be stopped and the peak values of the EUT would be reported. Otherwise the emissions that did not have 10dB margin would be re-tested one by one using peak, quasi-peak or average method as specified and then reported in a data sheet. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch. Report No.: SZEM160900821203 Page : 14 of 31 h. Test the EUT in the lowest channel, the middle channel, the Highest channel i. The radiation measurements are performed in X, Y, Z axis positioning for Transmitting mode,And found the X axis positioning which it is worse case. j. Repeat above procedures until all frequencies measured was complete. Instruments Used: Refer to section 5.10 for details Exploratory Test Mode: Transmitting mode Final Test Mode: Pretest the EUT at Transmitting mode Only the worst case is recorded in the report. Test Results: Pass This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch. Report No.: SZEM160900821203 Page : 15 of 31 Measurement Data 6.2.1.1 Field Strength Of The Fundamental Signal Peak value: Cable Antenna Preamp Read Over Frequency Level Limit Line Loss Factor Factor Level Limit Polarization (MHz) (dBuV/m) (dBuV/m) (dB) (dB/m) (dB) (dBuV) (dB) 2406.836 28.63 5.35 38.15 101.81 97.64 114.00 -16.36 Horizontal 2406.938 28.63 5.35 38.15 99.74 95.57 114.00 -18.43 Vertical 2441.719 28.79 5.38 38.15 100.26 96.28 114.00 -17.72 Horizontal 2441.839 28.79 5.38 38.15 98.38 94.40 114.00 -19.60 Vertical 2477.281 28.96 5.40 38.15 101.15 97.36 114.00 -16.64 Horizontal 2476.721 28.95 5.40 38.15 97.36 93.56 114.00 -20.44 Vertical Average value: Cable Antenna Preamp Read Over Frequency Level Limit Line Loss Factor Factor Level Limit Polarization (MHz) (dBuV/m) (dBuV/m) (dB) (dB/m) (dB) (dBuV) (dB) 2406.836 28.63 5.35 38.15 88.63 84.46 94.00 -9.54 Horizontal 2406.938 28.63 5.35 38.15 86.57 82.40 94.00 -11.60 Vertical 2441.719 28.79 5.38 38.15 87.49 83.51 94.00 -10.49 Horizontal 2441.839 28.79 5.38 38.15 85.27 81.29 94.00 -12.71 Vertical 2477.281 28.96 5.40 38.15 88.51 84.72 94.00 -9.28 Horizontal This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch. Report No.: SZEM160900821203 Page : 16 of 31 6.2.1.2 Spurious Emissions Radiated emission below 1GHz Test mode: Transmitter mode Polarization: Vertical This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch. Report No.: SZEM160900821203 Page : 17 of 31 Test mode: Transmitter mode Polarization: Horizontal This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch. Report No.: SZEM160900821203 Page : 18 of 31 Above 1GHz Test mode: Transmitting Test channel: Lowest Remark: Peak Antenna Cable Preamp Read Over Frequency Level Limit Line Factor loss Factor Level Limit Polarization (MHz) (dBuV/m) (dBuV/m) (dB/m) (dB) (dB) (dBuV) (dB) 4141.794 33.60 7.99 38.76 45.09 47.92 74.00 -26.08 Vertical 4814.000 34.18 8.88 39.03 47.90 51.93 74.00 -22.07 Vertical 6033.930 34.73 10.52 38.98 44.77 51.04 74.00 -22.96 Vertical 7221.000 36.41 10.69 38.17 43.05 51.98 74.00 -22.02 Vertical 9628.000 37.53 12.51 36.98 39.40 52.46 74.00 -21.54 Vertical 11625.290 38.23 14.16 37.94 39.02 53.47 74.00 -20.53 Horizontal 3786.875 33.03 7.74 38.60 44.90 47.07 74.00 -26.93 Horizontal 4814.000 34.18 8.88 39.03 49.24 53.27 74.00 -20.73 Horizontal 6066.451 34.76 10.47 38.96 45.05 51.32 74.00 -22.68 Horizontal 7221.000 36.41 10.69 38.17 43.45 52.38 74.00 -21.62 Horizontal Test mode: Transmitting Test channel: Middle Remark: Peak Antenna Cable Preamp Read Over Frequency Level Limit Line Factor loss Factor Level Limit Polarization (MHz) (dBuV/m) (dBuV/m) (dB/m) (dB) (dB) (dBuV) (dB) 3653.574 32.65 7.69 38.54 44.32 46.12 74.00 -27.88 Vertical 4884.000 34.30 8.98 39.06 48.03 52.25 74.00 -21.75 Vertical 6154.034 34.83 10.36 38.90 44.68 50.97 74.00 -23.03 Vertical 7326.000 36.37 10.73 38.06 42.15 51.19 74.00 -22.81 Vertical 9768.000 37.55 12.59 36.91 39.15 52.38 74.00 -21.62 Vertical 11667.020 38.27 14.20 37.98 38.66 53.15 74.00 -20.85 Horizontal 3588.694 32.46 7.66 38.51 45.29 46.90 74.00 -27.10 Horizontal 4884.000 34.30 8.98 39.06 48.25 52.47 74.00 -21.53 Horizontal 5948.056 34.67 10.42 39.00 46.24 52.33 74.00 -21.67 Horizontal 7326.000 36.37 10.73 38.06 41.93 50.97 74.00 -23.03 Horizontal This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch. Report No.: SZEM160900821203 Page : 19 of 31 Test mode: Transmitting Test channel: Highest Remark: Peak Antenna Cable Preamp Read Over Frequency Level Limit Line Factor loss Factor Level Limit Polarization (MHz) (dBuV/m) (dBuV/m) (dB/m) (dB) (dB) (dBuV) (dB) 3746.382 32.91 7.72 38.59 44.93 46.97 74.00 -27.03 Vertical 4954.000 34.42 9.08 39.08 48.46 52.88 74.00 -21.12 Vertical 6077.331 34.76 10.46 38.95 45.04 51.31 74.00 -22.69 Vertical 7431.000 36.33 10.76 37.95 42.38 51.52 74.00 -22.48 Vertical 9908.000 37.58 12.66 36.84 39.18 52.58 74.00 -21.42 Vertical 11963.380 38.56 14.52 38.26 39.12 53.94 74.00 -20.06 Horizontal 4017.537 33.60 7.83 38.71 45.11 47.83 74.00 -26.17 Horizontal 4954.000 34.42 9.08 39.08 48.36 52.78 74.00 -21.22 Horizontal 6333.012 34.97 10.13 38.79 45.97 52.28 74.00 -21.72 Horizontal 7431.000 36.33 10.76 37.95 41.89 51.03 74.00 -22.97 Horizontal Remark: 1) The field strength is calculated by adding the Antenna Factor, Cable Factor & Preamplifier. The basic equation with a sample calculation is as follows: Final Test Level =Receiver Reading + Antenna Factor + Cable Factor – Preamplifier Factor 2) Scan from 9kHz to 25GHz,The disturbance above 13GHz and below 30MHz was very low, and the above harmonics were the highest point could be found when testing, so only the above harmonics had been displayed. The amplitude of spurious emissions from the radiator which are attenuated more than 20dB below the limit need not be reported . 3) As shown in this section, for frequencies above 1GHz, the field strength limits are based on average limits. However, the peak field strength of any emission shall not exceed the maximum permitted average limits specified above by more than 20 dB under any condition of modulation. So, only the peak measurements were shown in the report. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch. Report No.: SZEM160900821203 Page : 20 of 31 6.3 Restricted bands around fundamental frequency Test Requirement: 47 CFR Part 15C Section 15.209 and 15.205 Test Method: ANSI C63.10: 2013 Test site: Measurement Distance: 3m (Semi-Anechoic Chamber) Limit(band edge): Emissions radiated outside of the specified frequency bands, except for harmonics, shall be attenuated by at least 50 dB below the level of the fundamental or to the general radiated emission limits in Section 15.209, whichever is the lesser attenuation. Frequency Limit (dBuV/m @3m) Remark 30MHz-88MHz 40.0 Quasi-peak Value 88MHz-216MHz 43.5 Quasi-peak Value 216MHz-960MHz 46.0 Quasi-peak Value 960MHz-1GHz 54.0 Quasi-peak Value 54.0 Average Value Above 1GHz 74.0 Peak Value Test Setup: Figure 1. 30MHz to 1GHz Figure 2. Above 1 GHz This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch. Report No.: SZEM160900821203 Page : 21 of 31 Test Procedure: a. For below 1GHz, the EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter semi-anechoic camber. The table was rotated 360 degrees to determine the position of the highest radiation. b. For above 1GHz, the EUT was placed on the top of a rotating table 1.5 meters above the ground at a 3 meter semi-anechoic camber. The table was rotated 360 degrees to determine the position of the highest radiation. c. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. d. The antenna height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. e. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. f. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. g. Place a marker at the end of the restricted band closest to the transmit frequency to show compliance. Also measure any emissions in the restricted bands. Save the spectrum analyzer plot. Repeat for each power and modulation for lowest and highest channel h. Test the EUT in the lowest channel , the Highest channel i. The radiation measurements are performed in X, Y, Z axis positioning for Transmitting mode,And found the X axis positioning which it is worse case.. j. Repeat above procedures until all frequencies measured was complete. Instruments Used: Refer to section 5.10 for details Exploratory Test Mode: Transmitting mode Final Test Mode: Pretest the EUT at Transmitting mode Only the worst case is recorded in the report. Test Results: Pass This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch. Report No.: SZEM160900821203 Page : 22 of 31 Measurement Data Worse case Test channel: Lowest Remark: Vertical mode: This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch. Report No.: SZEM160900821203 Page : 23 of 31 Worse case mode: Test channel: Lowest Remark: Horizontal This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch. Report No.: SZEM160900821203 Page : 24 of 31 Worse case mode: Test channel: Middle Remark: Vertical This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch. Report No.: SZEM160900821203 Page : 25 of 31 Worse case mode: Test channel: Middle Remark: Horizontal This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch. Report No.: SZEM160900821203 Page : 26 of 31 Worse case mode: Test channel: Highest Remark: Vertical This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch. Report No.: SZEM160900821203 Page : 27 of 31 Worse case mode: Test channel: Highest Remark: Horizontal Note: The field strength is calculated by adding the Antenna Factor, Cable Factor & Preamplifier. The basic equation with a sample calculation is as follows: Final Test Level =Receiver Reading + Antenna Factor + Cable Factor – Preamplifier Factor This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch. Report No.: SZEM160900821203 Page : 28 of 31 6.4 20dB Bandwidth Test Requirement: 47 CFR Part 15C Section 15.215 Test Method: ANSI C63.10:2013 Test Setup: Instruments Used: Refer to section 5.10 for details Test mode: Transmitting mode Limit: N/A Test Results: Pass Measurement Data Test channel 20dB bandwidth (MHz) Results Lowest 1.458 Pass Middle 1.326 Pass Highest 1.572 Pass This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch. Report No.: SZEM160900821203 Page : 29 of 31 Test plot as follows: Test channel: Lowest * RBW 100 kHz Marker 1 [T1 ] * VBW 300 kHz -17.84 dBm Ref -10 dBm Att 20 dB SWT 2.5 ms 2.407300000 GHz -10 ndB [T1] 20.00 dB 1 BW 1.458000000 MHz Temp 1 [T1 ndB] A -20 -37.88 dBm 1 PK 2.406118000 GHz MAXH -30 Temp T1 T2 -40 -50 -60 3DB -70 -80 -90 -100 -110 Center 2.407 GHz 300 kHz/ Span 3 MHz Test channel: Middle * RBW 100 kHz Marker 1 [T1 ] * VBW 300 kHz -25.37 dBm Ref -10 dBm Att 20 dB SWT 2.5 ms 2.441694000 GHz -10 ndB [T1] 20.00 dB BW 1.326000000 MHz Temp 1 [T1 ndB] A -20 1 -45.23 dBm 1 PK 2.441196000 GHz MAXH -30 Temp 2 [T1 ndB] -46.10 dBm 2.442522000 GHz -40 T1 T2 -50 -60 3DB -70 -80 -90 -100 -110 Center 2.442 GHz 300 kHz/ Span 3 MHz This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch. Report No.: SZEM160900821203 Page : 30 of 31 Test channel: Highest * RBW 100 kHz Marker 1 [T1 ] * VBW 300 kHz -20.34 dBm Ref -10 dBm Att 20 dB SWT 2.5 ms 2.476694000 GHz -10 ndB [T1] 20.00 dB BW 1.572000000 MHz 1 Temp 1 [T1 ndB] A -20 -40.37 dBm 1 PK 2.476268000 GHz MAXH -30 Temp 2 [T1 ndB] -40.50 dBm T1 T2 2.477840000 GHz -40 -50 -60 3DB -70 -80 -90 -100 -110 Center 2.477 GHz 300 kHz/ Span 3 MHz This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch. Report No.: SZEM160900821203 Page : 31 of 31 7 Photographs Test Item No.: 44519TX 7.1 Radiated Emission Test Setup 7.2 EUT Constructional Details Refer to Appendix A - Photographs of EUT Constructional Details for SZEM1609008212CR. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.


Document Created: 2016-11-07 05:44:51
Document Modified: 2016-11-07 05:44:51
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC