Test Report

FCC ID: PQN44344RX49

Test Report

Download: PDF
FCCID_1023367

Spin Master Toys Far East Ltd. Application For Certification (FCC ID: PQN44344RX49) Superregenerative Receiver Sample Description : Wind Chaser Model : 44344 HK08091368-1 BC/at October 27, 2008 • The test results reported in this report shall refer only to the sample actually tested and shall not refer or be deemed to refer to bulk from which such a sample may be said to have been obtained. • This report shall not be reproduced except in full without prior authorization from Intertek Testing Services Hong Kong Limited • The evaluation data of the report will be kept for 3 years from the date of issuance. FCC ID : PQN44344RX49

INTERTEK TESTING SERVICES LIST OF EXHIBITS INTRODUCTION EXHIBIT 1: General Description EXHIBIT 2: System Test Configuration EXHIBIT 3: Emission Results EXHIBIT 4: Equipment Photographs EXHIBIT 5: Product Labelling EXHIBIT 6: Technical Specifications EXHIBIT 7: Instruction Manual EXHIBIT 8: Miscellaneous Information FCC ID: PQN44344RX49 i

INTERTEK TESTING SERVICES MEASUREMENT/TECHNICAL REPORT Spin Master Toys Far East Ltd. - MODEL: 44344 FCC ID: PQN44344RX49 October 27, 2008 This report concerns (check one:) Original Grant X Class II Change Equipment Type: Superregenerative Receiver Deferred grant requested per 47 CFR 0.457(d)(1)(ii)? Yes No X If yes, defer until: date Company Name agrees to notify the Commission by: date of the intended date of announcement of the product so that the grant can be issued on that date. Transition Rules Request per 15.37? Yes No X If no, assumed Part 15, Subpart B for unintentional radiator Report prepared by: Chow Chi Ming, Billy Intertek Testing Services 2/F., Garment Center, 576, Castle Peak Road, HONG KONG Phone: 852-2173-8517 Fax: 852-2742-9149 FCC ID: PQN44344RX49 ii

INTERTEK TESTING SERVICES Table of Contents 1.0 General Description ................................................................................................. 2 1.1 Product Description............................................................................................... 2 1.2 Related Submittal(s) Grants .................................................................................. 2 1.3 Test Methodology ................................................................................................. 3 1.4 Test Facility .......................................................................................................... 3 2.0 System Test Configuration ...................................................................................... 5 2.1 Justification........................................................................................................... 5 2.2 EUT Exercising Software ...................................................................................... 5 2.3 Special Accessories.............................................................................................. 5 2.4 Equipment Modification......................................................................................... 6 2.5 Measurement Uncertainty ..................................................................................... 6 2.6 Support Equipment List and Descripition .............................................................. 6 3.0 Emission Results ..................................................................................................... 8 3.1 Field Strength Calculation ..................................................................................... 9 3.2 Radiated Emission Configuration Photograph ..................................................... 10 3.3 Radiated Emission Data...................................................................................... 11 4.0 Equipment Photographs........................................................................................ 14 5.0 Product Labelling................................................................................................... 16 6.0 Technical Specifications........................................................................................ 18 7.0 Instruction Manual ................................................................................................. 20 8.0 Miscellaneous Information .................................................................................... 22 8.1 Stabilization Waveform........................................................................................ 23 8.2 Emissions Test Procedures................................................................................. 24 FCC ID: PQN44344RX49 iii

INTERTEK TESTING SERVICES List of attached file Exhibit type File Description filename Test Report Test Report report.pdf Cover Letter Letter of Agency letter.pdf Operation Description Technical Description descri.pdf Test Setup Photo Radiated Emission radiated photos.pdf Test Report Stabilization Waveform superreg.pdf External Photo External Photo external photos.pdf Internal Photo Internal Photo internal photos.pdf Block Diagram Block Diagram block.pdf Schematics Circuit Diagram circuit.pdf ID Label/Location Label Artwork and Location label.pdf User Manual User Manual manual.pdf FCC ID: PQN44344RX49 iv

INTERTEK TESTING SERVICES EXHIBIT 1 GENERAL DESCRIPTION FCC ID: PQN44344RX49 1

INTERTEK TESTING SERVICES 1.0 General Description 1.1 Product Description The equipment under test (EUT) is a receiver for a RC Kite operating at 49.860 MHz. The EUT is powered by 2 x AAA size batteries. The EUT has an ON/OFF switch. After switched ON the EUT, the RC Kite can be controlled to turn left side or right side in the sky. The brief circuit description is saved with filename: descri.pdf 1.2 Related Submittal(s) Grants This is a single application for certification of a receiver. The transmitter for this receiver is authorized by Certification procedure with FCC ID: PQN44344TX49. FCC ID: PQN44344RX49 2

INTERTEK TESTING SERVICES 1.3 Test Methodology The radiated emission measurements were performed according to the procedures in ANSI C63.4 (2003). All measurements were performed in Open Area Test Sites. Preliminary scans were performed in the Open Area Test Sites only to determine worst case modes. All Radiated tests were performed at an antenna to EUT distance of 3 meters, unless stated otherwise in the "Justification Section" of this Application. 1.4 Test Facility The open area test site and conducted measurement facility used to collect the emission data is located at Garment Centre, 576 Castle Peak Road, Kowloon, Hong Kong. This test facility and site measurement data have been fully placed on file with the FCC. FCC ID: PQN44344RX49 3

INTERTEK TESTING SERVICES EXHIBIT 2 SYSTEM TEST CONFIGURATION FCC ID: PQN44344RX49 4

INTERTEK TESTING SERVICES 2.0 System Test Configuration 2.1 Justification The system was configured for testing in a typical fashion (as a customer would normally use it), and in the confines as outlined in ANSI C63.4 (2003). The EUT was powered by 2 new AAA battereis during test. For maximizing emissions, the EUT was rotated through 360°, the antenna height was varied from 1 meter to 4 meters above the ground plane, and the antenna polarization was changed. This step by step procedure for maximizing emissions led to the data reported in Exhibit 3.0. The unit was operated standalone and placed in the center of the turntable. The equipment under test (EUT) was configured for testing in a typical fashion (as a customer would normally use it). The EUT was placed on the turntable, which enabled the engineer to maximize emissions through its placement in the three orthogonal axes. 2.2 EUT Exercising Software There was no special software to exercise the device. 2.3 Special Accessories There are no special accessories necessary for compliance of this product. FCC ID: PQN44344RX49 5

INTERTEK TESTING SERVICES 2.4 Equipment Modification Any modifications installed previous to testing by Spin Master Toys Far East Ltd. will be incorporated in each production model sold/leased in the United States. No modifications were installed by Intertek Testing Services. 2.5 Measurement Uncertainty When determining the test conclusion, the measurement uncertainty of test has been considered. 2.6 Support Equipment List and Description This product was tested in a standalone configuration. All the items listed under section 2.0 of this report are Confirmed by: Chow Chi Ming, Billy Manager Intertek Testing Services Agent for Spin Master Toys Far East Ltd. Signature October 27, 2008 Date FCC ID: PQN44344RX49 6

INTERTEK TESTING SERVICES EXHIBIT 3 EMISSION RESULTS FCC ID: PQN44344RX49 7

INTERTEK TESTING SERVICES 3.0 Emission Results Data is included worst case configuration (the configuration which resulted in the highest emission levels). A sample calculation, configuration photographs and data tables of the emissions are included. FCC ID: PQN44344RX49 8

INTERTEK TESTING SERVICES 3.1 Field Strength Calculation The field strength is calculated by adding the Antenna Factor and Cable Factor, and subtracting the Amplifier Gain (if any) from the measured reading. The basic equation with a sample calculation is as follows: FS = RA + AF + CF - AG where FS = Field Strength in dBμV/m RA = Receiver Amplitude (including preamplifier) in dBμV CF = Cable Attenuation Factor in dB AF = Antenna Factor in dB AG = Amplifier Gain in dB In the following table(s), the reading shown on the data table reflects the preamplifier gain. An example for the calculations in the following table is as follows: FS = RR + LF where FS = Field Strength in dBμV/m RR = RA - AG in dBμV LF = CF + AF in dB Assume a receiver reading of 52.0 dBμV is obtained. The antenna factor of 7.4 dB and cable factor of 1.6 dB are added. The amplifier gain of 29 dB is subtracted, giving a field strength of 32 dBμV/m. This value in dBμV/m was converted to its corresponding level in μV/m. RA = 52.0 dBμV/m AF = 7.4 dB RR = 23.0 dBμV CF = 1.6 dB LF = 9.0 dB AG = 29.0 dB FS = RR + LF FS = 23 + 9 = 32 dBμV/m Level in µV/m = Common Antilogarithm [(32 dBμV/m)/20] = 39.8 μV/m FCC ID: PQN44344RX49 9

INTERTEK TESTING SERVICES 3.2 Radiated Emission Configuration Photograph Worst Case Radiated Emission 48.483 MHz For electronic filing, the worst case radiated emission configuration photograph is saved with filename: radiated photos.pdf FCC ID: PQN44344RX49 10

INTERTEK TESTING SERVICES 3.3 Radiated Emission Data The data on the following page lists the significant emission frequencies, the limit and the margin of compliance. Numbers with a minus sign are below the limit. Judgement: Passed by 5.9 dB TEST PERSONNEL: Signature Ben Ho, Compliance Engineer Typed/Printed Name October 27, 2008 Date FCC ID: PQN44344RX49 11

INTERTEK TESTING SERVICES Applicant: Spin Master Toys Far East Ltd. Date of Test: September 30, 2008 Model: 44344 Mode: RX Sample: 1/2 Table 1 Radiated Emissions Pre- Antenna Net Limit Frequency Reading amp Factor at 3m at 3m Margin Polarization (MHz) (dBμV) (dB) (dB) (dBμV/m) (dBμV/m) (dB) V 43.261 38.9 16 10.0 32.9 40.0 -7.1 V 45.582 39.6 16 10.0 33.6 40.0 -6.4 V 48.483 39.1 16 11.0 34.1 40.0 -5.9 V 50.296 38.8 16 11.0 33.8 40.0 -6.2 V 53.684 37.4 16 11.0 32.4 40.0 -7.6 V 90.254 35.6 16 11.0 30.6 43.5 -12.9 V 94.371 35.9 16 11.0 30.9 43.5 -12.6 V 96.429 33.8 16 12.0 29.8 43.5 -13.7 V 112.276 31.2 16 14.0 29.2 43.5 -14.3 V 114.429 32.4 16 14.0 30.4 43.5 -13.1 V 115.534 30.6 16 14.0 28.6 43.5 -14.9 Notes: 1. Negative sign in the column shows value below limit. 2. Peak Detector Data unless otherwise stated. 3. All measurements were made at 3 meter. Harmonic emissions not detected at the 3- meter distance were measured at 0.3-meter and an inverse proportional extrapolation was performed to compare the signal level to the 3-meter limit. No other harmonic emissions than those reported were detected at a test distance of 0.3-meter. Test Engineer: Ben Ho FCC ID: PQN44344RX49 12

INTERTEK TESTING SERVICES EXHIBIT 4 EQUIPMENT PHOTOGRAPHS FCC ID: PQN44344RX49 13

INTERTEK TESTING SERVICES 4.0 Equipment Photographs For electronic filing, the photographs are saved with filename: external photos.pdf and internal photos.pdf FCC ID: PQN44344RX49 14

INTERTEK TESTING SERVICES EXHIBIT 5 PRODUCT LABELLING FCC ID: PQN44344RX49 15

INTERTEK TESTING SERVICES 5.0 Product Labelling For electronic filing, the FCC ID label artwork and the label location are saved with filename: label.pdf FCC ID: PQN44344RX49 16

INTERTEK TESTING SERVICES EXHIBIT 6 TECHNICAL SPECIFICATIONS FCC ID: PQN44344RX49 17

INTERTEK TESTING SERVICES 6.0 Technical Specifications For electronic filing, the block diagram and schematics are saved with filename: block.pdf and circuit.pdf respectively. FCC ID: PQN44344RX49 18

INTERTEK TESTING SERVICES EXHIBIT 7 INSTRUCTION MANUAL FCC ID: PQN44344RX49 19

INTERTEK TESTING SERVICES 7.0 Instruction Manual For electronic filing, a preliminary copy of the Instruction Manual is saved with filename: manual.pdf This manual will be provided to the end-user with each unit sold/leased in the United States. FCC ID: PQN44344RX49 20

INTERTEK TESTING SERVICES EXHIBIT 8 MISCELLANEOUS INFORMATION FCC ID: PQN44344RX49 21

INTERTEK TESTING SERVICES 8.0 Miscellaneous Information This miscellaneous information includes details of the stabilizing process (including a plot of the stabilized waveform) and the test procedure. FCC ID: PQN44344RX49 22

INTERTEK TESTING SERVICES 8.1 Stabilization Waveform Previous to the testing, the superregenerative receiver was stabilized as outlined in the test procedure. The plot saved on the filename : superreg.pdf shows the fundamental emission when a signal generator was used to stabilize the receiver. Please note that the antenna was placed as close as possible to the EUT for clear demonstration of the waveform and that accurate readings are not possible from this plot. FCC ID: PQN44344RX49 23

INTERTEK TESTING SERVICES 8.2 Emissions Test Procedures The following is a description of the test procedure used by Intertek Testing Services Hong Kong Ltd. in the measurements of superregenerative receivers operating under the Part 15, Subpart B rules. The test set-up and procedures described below are designed to meet the requirements of ANSI C63.4 - 2003. Superregenerative receivers are stabilized prior to measurement by generating a signal well above the receiver threshold whose frequency is tuned until the emissions stabilize into a line spectrum. The signal is usually generated as CW with a Marconi 2022D signal generator and a short whip antenna and is at a level of several hundred to several thousand mV/m. Plots of the stabilized signal will be shown. If a modulated signal is used, it will be noted. The equipment under test (EUT) is placed on a wooden turntable which is four feet in diameter and approximately one meter in height above the groundplane. During the radiated emissions test, the turntable is rotated and any cables leaving the EUT are manipulated to find the configuration resulting in maximum emissions. The antenna height and polarization are also varied during the testing to search for maximum signal levels. The height of the antenna is varied from one to four meters. Detector function for radiated emissions is in peak mode. Average readings, when required, are taken by measuring the duty cycle of the equipment under test and subtracting the corresponding amount in dB from the measured peak readings. The frequency range scanned is from 30 MHz to 1000 MHz. FCC ID: PQN44344RX49 24

INTERTEK TESTING SERVICES 8.2 Emissions Test Procedures (cont’d) The EUT is warmed up for 15 minutes prior to the test. AC power to the unit is varied from 85% to 115% nominal and variation in the fundamental emission field strength is recorded. If battery powered, a new, fully charged battery is used. Conducted measurements were made as described in ANSI C63.4 - 2003. The IF bandwidth used for measurement of radiated signal strength was 10 kHz for emission below 30 MHz and 120 kHz for emission from 30 MHz to 1000 MHz. Above 1000 MHz, a resolution bandwidth of 1 MHz is used. Measurements are normally conducted at a measurement distance of three meters. All measurements are extrapolated to three meters using inverse scaling, unless otherwise reported. Measurements taken at a closer distance are so marked. FCC ID: PQN44344RX49 25


Document Created: 2008-10-27 15:24:40
Document Modified: 2008-10-27 15:24:40
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC