User Manual

FCC ID: PQN44210TX27

Users Manual

Download: PDF
FCCID_667270

The Air Hogs® Room Raider®" is perfect for first—time flyers. There is no assembly required. ¥ All you need is an open space and six AA 1.5V alkaline batteries (not included) to take flight. ADULT SUPERVISION RECOMMENDED. PLEASE READ THESE INSTRUCTIONS BEFORE FLYING! | Power/Charge :"""flk \Controller/ Switch ——— & Charger \ Throttle Trigger INSTRUCTIONS Check to make sure contents are complete: 1 Air Hogs® Room Raider* with Motor/Propeller 1 Controller/Charger 1 Instruction Manual CONTROLLER/CHARGER BATTERY INSTALLATION IMPORTANT BATTERY INFORMATION w ~ 1. Use a Phillips screwdriver to unscrew and remove the * Batteries should always be replaced by an adult. battery holder from the controller. « Do not mix old and new batisties 2. Install six AA 1.5V alkaline batteries (not included) : in the controller, Be careful to align the positive (+) and * Do not mix alka!ine, standx-_:rd (carbon'-zinc). 9f negative (—) polarities with the corresponding markings rechargeable (nickel—cadmium) batteries. inside the battery holder. * Non—rechargeable batteries are not to be recharged. 3. Reinstall the battery holder and tighten the screw. * Rechargeable batteries are to be removed from the toy before being charged (if removable). Controller Battery * Rechargeable batteries are only to be charged under Compartment adult supervision (if removable). * Different types of batteries or new and used batteries are not to be mixed. / * Only batteries of the same or equivalent type as recommended are to be used. Battery . h i Holder * Batteries are to be inserted with the correct polarity. * Exhausted batteries are to be removed from the toy. Si’;f::“;'esv _ * The supply terminals are not to be short—cirouited. Batteries —_~ %"Copy * Please retain this information for future reference. %% CAUTION: Do not dispose of batteries in fire. Batteries "C . may explode or leak. * / Familiarize yourself with the position of the "ON/OFF" switch, FLYING INDOORS and Charge Port. Location — Fly in a wide open room, away from breakable items. Avoid flying near vents and/or fans, as these may overpower the Room Raider®" and make it difficult to control. NOTE: Always get permission to fly your Room Raider®"indoors. WARNING: Never fly near your face. Keep propeller away from your fingers, hair, eyes and other body parts. Always lift off from a flat surface. Never hold the Room Raider"" by the bottom fin. Do not launch jet near people or animals. Stay away from obstacles and electric hazards. "ON/OFF" Switch Charge Port

CHARGING YOUR ROOM RAIDER®" 1. Open door on the controller to access the charge cable. 2. Plug charge cable into the charge port. 3. Slide the power switch on the controller to "CHARGE®. The charge light will flash while charging and stop flashing when the battery is fully charged. 4. Remove the charge cable from the charge port, store it in the charger and close the storage door. NOTE: For best flight performance, fully charge your Room Raider®"before each flight. FLYING YOUR ROOM RAIDER®" 1. Turn the jet "ON/OFF" switch to "ON‘". 2. Turn the controller "ON". Proper Grip for Launch 3. Hold the controller in one hand and jet as shown. 4. Squeeze the throttle trigger about 1/2 way and gently toss the Room Raider® into the air. The Room Raider"" will begin flying in circles to the left. 5. Control the altitude by squeezing the throttle trigger \ Do not hold here FCC REQUIREMENTS This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, includin%imerference that may cause undesired operation. WARNING: Changes or modifications not expressly approved by the party responsible for its compliance could void the user‘s authority to operate the equipment. RQ : «Lo PROBLEM CAUSE SOLUTION Room Raider®" 1. You have not set the motor switch to "ON". 1. Push motor switch switch to "ON". will not start or 2. Battery poweris low. 2. Replace the controller batteries. has lost power. 3. Batteries (+) or (—) are not correctly placed 3. Be sure to align the (+) and (—) polarities with the inside the battery compartment. corresponding markings inside the battery compartment. 4. Room Raider®" battery is low. 4. Recharge Room Raider®. 5. Safety auto—cutoff is activated. 5. Turn jet off, wait 3 seconds then turn back on Room Raider"" 1. Needs more power. 1. Squeeze the throttle trigger more. is flying too low. 2. The batteries in the controller are drained. 2. Install new batteries. 3. Room Raider®" battery is low. 3. Recharge Room Raider®. Spin Master Ltd., 450 Front Street West, Toronto, ON MBV 186 Canada TM and ©.2006 Spin Master Ltd. Air Hogs ® is a registered Spin Master, Inc.. PMB #10053, 300 International Drive, Suite 100, trademark of Spin Master L1d. All rights reserved. Conforms to tains Li it k Willamsvile, NY 14221, USA product safety standards ASTM F963—03, requlatoryrequirements g:,"“,“,;“alc'f“,,,‘:,‘s. f,r,y vack. Spin Master Toys Far East Limited, Rim #1113, 11/F Products and colors may vary. Please retain this information for Chinachem Golden Plaza, 77 Mody Rd., Tsimshatsut E., Kowloon, HK future reference. Patent Pending reeyited or disposed af MADE IN CHINA properly, y — North American Consumer Information \C Phone: 1—800—622—8339 Item#44210 4421U-ENG-|5-RTS1) j\r 7 x www spinmaster.com #20004655, #20004658 REV 1 US English

L=I css Item #44210 NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installa— tion. This equipment generates, uses, and can radiate radio fre— quency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio com— munications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: — Reorient or relocate the receiving antenna. — Increase the separation between the equipment and receiver. — Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. — Consult the dealer or an experienced radio / TV technician for help.


Document Created: 2006-06-01 14:38:57
Document Modified: 2006-06-01 14:38:57
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC