modular aproval

FCC ID: PPQ-WZ400T

Cover Letter(s)

Download: PDF
FCCID_1255464

RF_734_00, Issue 1 Modular Approval Request FCC (per DA 00-1407) FCC ID: PPQ-WZ400T Items to be covered Answer from applicant 1. The modular transmitter must have its own RF shielding. The modular transmitter have its own RF shielding. 2. The modular transmitter must have buffered modulation/data inputs (if such inputs The EUT has buffered data are provided) to ensure that the module will comply with Part 15 requirements inputs, it is integrated in chip under conditions of excessive data rates or over-modulation. CC2530. 3. The modular transmitter must have its own power supply regulation. The EUT has regulator, it is integrated in chip CC2530. 4. The modular transmitter must comply with the antenna requirements of Section The modular transmitter 15.203 and 15.204(c). The antenna must either be permanently attached or employ complies with the antenna a “unique” antenna coupler (at all connections between the module and the antenna, requirements of Section including the cable).. 15.203 and 15.204(c). 5. The modular transmitter must be tested in a stand-alone configuration, i.e., the The modular transmitter is module must not be inside another device during testing. This is intended to tested in a stand-alone demonstrate that the module is capable of complying with Part 15 emission limits configuration. regardless of the device into which it is eventually installed. 6. The modular transmitter must be labeled with its own FCC ID number, and, if the The modular transmitter is FCC ID is not visible when the module is installed inside another device, then the labeled with its own FCC ID outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the number. following: “Contains Transmitter Module FCC ID: XYZMODEL1” or “Contains FCC ID: XYZMODEL1.” Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. 7. The modular transmitter must comply with any specific rule or operating The modular transmitter requirements applicable to the transmitter and the manufacturer must provide complies with any specific adequate instructions along with the module to explain any such requirements. A rule or operating requirements copy of these instructions must be included in the application for equipment applicable to the transmitter authorization. For example, there are very strict operational and timing and the manufacturer must requirements that must be met before a transmitter is authorized for operation under provide adequate instructions Section 15.231. For instance, data transmission is prohibited, except for operation along with the module to under Section 15.231(e), in which case there are separate field strength level and explain any such timing requirements. Compliance with these requirements must be assured. requirements. 8. The modular transmitter must comply with any applicable RF exposure The modular transmitter requirements. For example, FCC Rules in Sections 2.1091, 2.1093 and specific complies with any applicable Sections of Part 15, including 15.319(i), 15.407(f), 15.253(f) and 15.255(g), require that Unlicensed PCS, UNII and millimeter wave devices perform routine RF exposure requirements. environmental evaluation for RF Exposure to demonstrate compliance. In addition, spread spectrum transmitters operating under Section 15.247 are required to address RF Exposure compliance in accordance with Section 15.247(b)(4). Modular transmitters approved under other Sections of Part 15, when necessary, may also need to address certain RF Exposure concerns, typically by providing specific installation and operating instructions for users, installers and other interested parties to ensure compliance. Note: If compliance with one or more of the numbered requirements, listed above, cannot be demonstrated, it may be possible to obtain a “Limited Modular Approval” (LMA). Name and surname of applicant (or authorized representative): TC Wu / Deputy Director (R & D Division) Date: __Mar.18,2010__ Signature: ___________________________


Document Created: 2010-03-19 09:43:46
Document Modified: 2010-03-19 09:43:46
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC