WN4638R FCC Modular Approval Letter Revised 1030

FCC ID: PPQ-WN4638R

Cover Letter(s)

Download: PDF
FCCID_2432358

Applicant/Grantee Lite-On Technology Corp. FCC ID: PPQ-WN4638R Section 15.212 Modular Transmitters Request for Modular Approval Request for Limited Modular Approval Requirements EUT Conditions Comply (Y/N) Single Modular Approval Requirements 1 The radio elements of the modular The modular have RF own shielding Y transmitter must have their own shielding. The physical crystal and tuning capacitors may be located external to the shielded radio elements. 2 The modular transmitter must have The modular transmitter have Y buffered modulation/data inputs (if such buffered modulation/data inputs inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over-modulation. 3 The modular transmitter must have its The module contains its own power Y own power supply regulation. supply regulation. Please refer to the block. 4 The modular transmitter must comply The modular must to built-in PIFA Y with the antenna and transmission applicant together and transmission system requirements of Sections 15.203, system requirements of Sections 15.203, 15.204(b) and 15.204(c). The antenna 15.204(b) and 15.204(c). must either be permanently attached or employ a “unique” antenna coupler (at all connections between the module and the antenna, including the cable). The “professional installation” provision of Section 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph (b) of this section. 5 The modular transmitter must be tested The EUT module can’t be operated by Y in a stand-alone configuration, i.e., the its own due to its power-less module must not be inside another characteristic and hence needs external device during testing for compliance power supply to make it function. with Part 15 requirements. Unless the Under testing condition, no matter in transmitter module will be battery pure verification or manufacturing stage, powered, it must comply with the AC the specified test fixture must be line conducted requirements found in provided to help testing the function and Section 15.207. AC or DC power lines performance of the EUT sample. and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module (see Section 15.27(a)). The length of these lines shall be the length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between

the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and commercially available (see Section 15.31(i)). 6 The modular transmitter must be The FCC identification number can put Y equipped with either a permanently on the modular with either a affixed label or must be capable of permanently affixed label electronically displaying its FCC identification number. (A) If using a permanently affixed label, the modular transmitter must be labeled with its own FCC identification number, and, if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: XYZMODEL1” or “Contains FCC ID: XYZMODEL1.” Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. (B) If the modular transmitter uses an electronic display of the FCC identification number, the information must be readily accessible and visible on the modular transmitter or on the device in which it is installed. If the module is installed inside another device, then the outside of the device into which the module is installed must display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains FCC certified transmitter module(s).” Any similar wording that expresses the same meaning may be used. The user manual must include instructions on how to access the electronic display. A copy of these instructions must be included in the application for equipment authorization. 7 The modular transmitter must comply The modular have specific rules or Y with any specific rules or operating operating requirements requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the

application for equipment authorization. 8 The modular transmitter must comply Y with any applicable RF exposure requirements in its final configuration. A modular approval may be granted for single or split modular transmitters that do not comply with all of the above requirements, e.g., shielding, minimum signaling amplitude, buffered modulation/data inputs, or power supply regulation, if the manufacturer can demonstrate by alternative means in the application for equipment authorization that the modular transmitter meets all the applicable Part 15 requirements under the operating conditions in which the transmitter will be used. Limited modular approval also may be granted in those instances where compliance with RF exposure rules is demonstrated only for particular product configurations. The applicant for certification must state how control of the end product into which the module will be installed will be maintained such that full compliance of the end product is always ensured. Name/Title: TC Wu / Director Company Name: Lite-On Technology Corp. Address: 4F, 90, Chien 1 Road, Chung Ho, New Taipei City 23585, Taiwan, R.O.C. TEL: 886-2-2222-6181 FAX: 886-2-2226-6749 Email: sandra.liu@liteon.com Date: Oct. 20, 2014


Document Created: 2014-10-27 11:21:47
Document Modified: 2014-10-27 11:21:47
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC