User Manual

FCC ID: PPQ-WCBN3509R

Users Manual

Download: PDF
FCCID_4476132

USER MANUAL 802.11a/b/g/n/ac 2Tx2R+BT5.0 USB WLAN Module WCBN3509R, WCBN3509R(AU) Page 1/15

PRODUCT FEATURES BT FEATURE:  Bluetooth V5.0 system Backwards compatible with BT version of 1.1, 1.2, 2.0, 2.1, 3.0+HS and 4.0LE  Bluetooth Class I transmission power  Support for Simple Pairing (SP) and Enhanced Inquiry Response (EIR) function  Support for SCATTERNET and up to 7 piconets simultaneously with background inquiry/page scan  Up to 7 BT link + 32BLE link  Support wide-band speech and hardware accelerated SBC codec for A2DP streaming  Packet loss concealment  Channel quality driven data rate adaptation  Support Wake On Bluetooth WI-FI FEATURE:  Operate at ISM frequency Band (2.4/5GHz)  IEEE Standards Support, 802.11a ,802.11b, 802.11g, 802.11n and 802.11ac  Support for both 20 MHz, 40MHz and 80 MHz channel width in 2.4GHz and 5GHz band  Enterprise level security supporting: WPS2.0,WAPI, WPA, WPA2  Support 2 transmission and 2 receiving, transmission rate can up to 300Mbps (Physical Rate) in downstream and upstream  Dual-stream IEEE 802.11ac support for 80MHz channels provides PHY layer rates up to 867Mbps  QoS support of WFA WMM, WMMPS  Support MU-MIMO RX  Support STBC, LDPC, TX&RX beamforming  Support Wake On WLAN COMMON FEATURE:  MT7668BU is a single chip integrated IEEE 802.11 a/b/g/n/ac and Bluetooth 5.0 with a single USB interface  PA, LNA, and T/R switch integration for Wi-Fi and Bluetooth  Advanced FDD/TDD mode Wi-Fi/Bluetooth coexistence scheme  Fully compliance with USB v2.0 specification  RoHS compliance  Low Halogen compliance Page 2/15

PRODUCT SPECIFICATIONS MAIN CHIPSET MediaTek MT7668BU FUNCTIONAL SPECIFICATIONS BT Function Standard Bluetooth V5.0LE Bus Interface USB2.0 Data Rate 1 Mbps, 2Mbps and Up to 3Mbps Modulation Scheme GFSK, π/4-DQPSK and 8-DPSK Frequency Range 2.402~2.480 GHz Transmit Output Power +4 ≤ Output Power ≤ +10dBm; Class I Device Receiver Sensitivity < 0.1% BER at -88dBm Wi-Fi Function IEEE802.11a; IEEE802.11b; IEEE 802.11g; IEEE 802.11n. Standard IEEE802.11ac Bus Interface USB2.0 802.11a: 54, 48, 36, 24, 18, 12, 9, 6 Mbps 802.11b: 11, 5.5, 2, 1 Mbps 802.11g: 54, 48, 36, 24, 18, 12, 9, 6 Mbps Data Rate 802.11n: MCS 0 to 15 for HT20MHz MCS 0 to 15 for HT40MHz 802.11ac: MCS 0 to 8 for HT20MHz MCS 0 to 9 for HT40MHz MCS 0 to 9 for HT80MHz Media Access Control CSMA/CA with ACK 802.11a: 64QAM, 16QAM, QPSK, BPSK 802.11b: CCK, DQPSK, DBPSK 802.11g: Modulation Technique 64QAM, 16QAM, QPSK, BPSK 802.11n: 64QAM, 16QAM, QPSK, BPSK 802.11ac: 256QAM, 64QAM, 16QAM, QPSK, BPSK Page 3/15

Ad-hoc mode (Peer-to-Peer) Network Architecture Infrastructure mode 2.4GHz 11: (Ch. 1-11) – United States 13: (Ch. 1-13) – Europe 14: (Ch. 1-14) – Japan Operation Channel 5GHz 21: USA 19: EU 8: Japan 802.11bg 2.400 ~ 2.4835 GHz Frequency Range 802.11a 5.15 ~ 5.85 GHz CCK < 35% OFDM < -25dB MCS0(HT20/40MHz) < -5dB MCS7(HT20/40MHz) < -28dB EVM MCS0(VHT20/40/80MHz) < -5dB MCS7(VHT 20/40/80MHz) < -27dB MCS8(VHT 20/40/80MHz) < -30dB MCS9(VHT 20/40/80MHz) < -32dB 2.4&5GHz Frequency Offset -20ppm < Center Frequency < +20ppm Transmit Output Power - single chain @ant; Tolerance: ±1.5dBm@2.4GHz; ±2dBm@5GHz 2.4GHz 802.11b 1Mbps 2Mbps 5.5Mbps 11Mbps Tgtpwr 16 16 16 16 (dBm) 802.11g 6~24Mbps 36Mbps 48Mbps 54Mbps Tgtpwr 15 15 15 15 (dBm) 802.11n MCS0 MCS1 MCS2 MCS3 MCS4 HT20 Tgtpwr 15 15 15 15 15 (dBm) MCS5 MCS6 MCS7 MCS8 MCS9 15 15 15 802.11n MCS0 MCS1 MCS2 MCS3 MCS4 HT40 Tgtpwr 15 15 15 15 15 (dBm) MCS5 MCS6 MCS7 MCS8 MCS9 15 15 15 5GHz 802.11a 6~24Mbps 36Mbps 48Mbps 54Mbps Tgtpwr 14 14 14 14 (dBm) Page 4/15

802.11n MCS0 MCS1 MCS2 MCS3 MCS4 HT20 Tgtpwr 14 14 14 14 14 (dBm) MCS5 MCS6 MCS7 MCS8 MCS9 14 14 14 802.11n MCS0 MCS1 MCS2 MCS3 MCS4 HT40 Tgtpwr 13 13 13 13 13 (dBm) MCS5 MCS6 MCS7 MCS8 MCS9 13 13 13 802.11ac MCS0 MCS1 MCS2 MCS3 MCS4 VHT20 Tgtpwr 14 14 14 14 14 (dBm) MCS5 MCS6 MCS7 MCS8 MCS9 14 14 14 14 802.11ac MCS0 MCS1 MCS2 MCS3 MCS4 VHT40 Tgtpwr 13 13 13 13 13 (dBm) MCS5 MCS6 MCS7 MCS8 MCS9 13 13 13 13 13 802.11ac MCS0 MCS1 MCS2 MCS3 MCS4 VHT80 Tgtpwr 12 12 12 12 12 (dBm) MCS5 MCS6 MCS7 MCS8 MCS9 12 12 12 12 12 Receiver Sensitivity Frequency Rate Condition Typical (1SS) Band (dBm) 11b-1M PER < 8% -94 11b-11M PER < 8% -86 11g-6M PER < 10% -90 11g-54M PER < 10% -73 2.4G 11n-HT20MCS0 PER < 10% -87 11n-HT20MCS7 PER < 10% -70 11n-HT40MCS0 PER < 10% -84 11n-HT40MCS7 PER < 10% -67 11a-6M PER < 10% -88 11a-54M PER < 10% -71 11ac-VHT20MCS0 PER < 10% -85 11ac-VHT20MCS7 PER < 10% -68 11ac-VHT20MCS8 PER < 10% -65 5G 11ac-VHT40MCS0 PER < 10% -82 11ac-VHT40MCS7 PER < 10% -65 11ac-VHT40MCS9 PER < 10% -61 11ac-VHT80MCS0 PER < 10% -80 11ac-VHT80MCS7 PER < 10% -63 Page 5/15

11ac-VHT80MCS9 PER < 10% -57 WPS, WPA, WPA2, WEP 64bit & 128bit, IEEE 802.1X, IEEE Security 802.11i Common Function Operating Voltage 3.3 V ±10% I/O supply voltage Mode Average Peak 2.4G 5G 2.4G 5G Power Consumption TX TBDmA TBDmA TBDmA TBDmA RX TBDmA TBDmA Unassocia TBDmA ted Idle Antenna Type Triple U.FL connectors for WiFi&BT RECOMMENDED OPERATION CONDITIONS Symbol Rating Min Typ Max Units VDD33 3.3V Supply Voltage 2.97 3.3 3.63 V VDD18 1.8V Supply Voltage 1.7 1.8 1.9 V 0 TAMNIENT Ambient Temperature -10 - 70 C DC CHARACTERISTICS Symbol Parameter Min Typ Max Units VIL Input Low Voltage -0.28 - 0.6 V VIH Input High Voltage 2.0 - 3.63 V VOL Output Low Voltage -0.28 - 0.4 VOH Output High Voltage 2.9 - 3.63 V POWER ON SEQUENCE TIMING Page 6/15

PIN ASSIGMENT Pin. Pin Define Description Status 1 +3.3V 3.3V source YES 2 +3.3V 3.3V source YES 3 USB_D- USB Data- YES 4 USB_D+ USB Data+ YES 5 GND Ground YES 6 RESET# System reset MT7668BU, low active YES 7 WoWLAN# Wake up system via wifi, low active YES 8 GND Ground YES 9 WoBT Wake up system via BT, low active YES 10 GND Ground YES 11 GND Ground YES 12 GND Ground YES 13 GND Ground YES 14 GND Ground YES FOOTPRINT Top View Page 7/15

MECHANICAL EEPROM INFORMATION WI-FI World Wide 2.4G/5G Reg Domain Read from registry; Control by driver Offset 0x38 for 5G: 0xFF Offset 0x39 for 2.4G: 0xFF Vendor ID 0x0E8D Device ID 0x7668 ENVIRONMENTAL OPERATING Ambient Operating Temperature: -10 to 70 °C (14 to 158 °F) Ambient Relative Humidity: 5-90% (non-condensing) STORAGE Ambient Temperature: -40 to 80 °C (-40 to 176 °F) Ambient Relative Humidity: 5-95% (non-condensing Page 8/15

WARNINGS FCC Statement: Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: ● Reorient or relocate the receiving antenna. ● Increase the separation between the equipment and receiver. ● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ● Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. This device and its antenna(s) must not be co-located with any other transmitters except in accordance with FCC multi-transmitter product procedures. Refering to the multi-transmitter policy, multiple-transmitter(s) and module(s) can be operated simultaneously without C2P. This device is restricted for indoor use. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter Page 9/15

IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. IMPORTANT NOTE: This module is intended for OEM integrator. The OEM integrator is responsible for the compliance to all the rules that apply to the product into which this certified RF module is integrated. Additional testing and certification may be necessary when multiple modules are used. 20 cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is integrated into. Under such configuration, the FCC radiation exposure limits set forth for an population/uncontrolled environment can be satisfied. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. USERS MANUAL OF THE END PRODUCT: In the users manual of the end product, the end user has to be informed to keep at least 20 cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the users manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. This device is restricted to indoor use. LABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following " Contains TX FCC ID: PPQ-WCBN3509R ". If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available on the label: This device Page 10/15

complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. IC Statement: This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : 1. L’appareil ne doit pas produire de brouillage; L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. Pour les produits disponibles aux États-Unis / Canada du marché, seul le canal 1 à 11 peuvent être exploités. Sélection d'autres canaux n'est pas possible. This device and its antenna(s) must not be co-located with any other transmitters except in accordance with IC multi-transmitter product procedures. Refering to the multi-transmitter policy, multiple-transmitter(s) and module(s) can be operated simultaneously without reassessment permissive change. Cet appareil et son antenne (s) ne doit pas être co-localisés ou fonctionnement en association avec une autre antenne ou transmetteur. The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems. les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux. Page 11/15

The maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate. le gain maximal d’antenne permis (pour les dispositifs utilisant la bande 5725-5850 MHz) doit se conformer à la limite de p.i.r.e. spécifiée pour l’exploitation point à point et non point à point, selon le cas. Dynamic Frequency Selection (DFS) for devices operating in the bands 5250- 5350 MHz, 5470-5600 MHz and 5650-5725 MHz. Sélection dynamique de fréquences (DFS) pour les dispositifs fonctionnant dans les bandes 5250-5350 MHz, 5470-5600 MHz et 5650-5725 MHz. The maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit. le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5250-5350 MHz et 5470-5725 MHz doit se conformer à la limite de p.i.r.e. Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. For indoor use only. Pour une utilisation en intérieur uniquement. IMPORTANT NOTE: IC Radiation Exposure Statement: This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. This radio transmitter (IC: 4491A-WCBN3509R) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, Page 12/15

having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le présent émetteur radio (IC: 4491A-WCBN3509R) a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur. The transmitter module may not be co-located with any other transmitter or antenna. Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne. This module is intended for OEM integrator. The OEM integrator is still responsible for the IC compliance requirement of the end product, which integrates this module. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. USERS MANUAL OF THE END PRODUCT: In the users manual of the end product, the end user has to be informed to keep at least 20 cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the IC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. The transmitter module may not be co-located with any other transmitter or antenna. Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne. LABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following " Contains TX IC : 4491A-WCBN3509R". Page 13/15

Table for Filed Antenna Page 14/15

Japan Statement: 5GHz product for indoor use only. CE Statement: This equipment complies with EU radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. Page 15/15


Document Created: 2019-10-11 10:31:44
Document Modified: 2019-10-11 10:31:44
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC