User Manual

FCC ID: PPQ-WB101N

Users Manual

Download: PDF
FCCID_4502651

User Manual

FCC Statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Notice: Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/ TV technician for help. Modular information form OEM Information to Be Supplied to the End User by the OEM or Integrator. The following regulatory and safety notices must be published in documentation supplied to the end user of the product or system incorporating an adapter in compliance with local regulations. Host system must be labeled with " Contains transmitter module FCC ID: PPQ-WB101N , FCC ID displayed on label.

The antenna(s) used for this transmitter must not be co-located of operating in conjunction with any other antenna or transmitter. This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. Ln order to avoid the possibility of exceeding the Fcc radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm (8inches) during normal operation.

uTE®1 Irtoaiforse tieonBE matse t olNados nRoCeeAowmingtntace Wt mrtornencedlavevces Cintonitw Eo) Anventirgncesns natsicaner. Beirganentltwitearentsconsat onsouttimensoi Hnonanerimm ae s petertmpon on ere Blocmat 0 ies Hocmah taSewre Comton acd m parte Wlocont 2 ovwen w anay w al undeo tanaver vinioeasptaon Y MEenio nede neen tnigh meal sn(UaT)macire the tm muatimetobervers redsand ebicarar o. Un reciietan onsmeet on «NCXh nadocsmevil Arentnsl n devenounateayan e derecemit mndon to redseshrogsannleaton. Anotatasprrs ooie esA rnante m eotgurecornin poranten h a n sotravniwin e vectlocnan cometoninenns aram cort m prarvacon uhn in oveoo fTanpares vareiaio tincg tynemien mtonseme coverentnfi meritos lormt deveimetcxpeinc c entrorenc. »Aeimetcendninantadnd UART (TTLinmerace ieb atome rtstinbrraden vaceniin wthinsicapenton ASaopert i poreiReariand. Lieaul mte rnenwcon nc HAtit n MSttonantrane o mdoieeralpoe

uTE®1 MaG adtrasantovertacinorraton Lo evernanatein ol becorvala y Iantare mport Ablere dne pesenptatary onl stt ut wtens Howimerean traicconsaiiewih ewon reo ‘reneresonditcect 0=20 Mevscia t Pravesisanrces ow rtzcs Sm iges tavaey (a¥pea) Cvenienunpemires 4o mss N: +tlowntaprniotenpertoe o ow sstage nade old e asee

uTE®T Prtectcttee nancoese recnowincnonee entimnnie 6 dn naseyi tanonInerpyrote Sureet t es s2e hmon repyrete (ttw 0 dn pomecutpntien us Gveto uin ngrcntirn «6 niparamene mcb 46 mipaiameniin ros teatnen wnircommeitisoonpmcemosctine (EEHRC oisoes neongtuntmeroy ant atticuemgtontnmemey 23 unbiesematomun Suntwe sass oo Reilcpommimpenn 17008¥ mogmatine AiysaomiciOwiDCtenzirernmun Fautacsnptt cmd ntver 109 vh> in nedsw itmece + 05 pa> ¥intun oned aniuztio uitreonsn <18 pha ¥intun Oinote btact10 Ritrearan, etecont©

192 kB flash and 24 kB RAM Nordic SoftDevice ready Support for concurrent multi-protocol 12-bit, 200 ksps ADC - 8 configurable channels with programmable gain 64 level comparator Temperature sensor Up to 32 general purpose I/O pins 4-channel pulse width modulator (PWM) unit with EasyDMA Digital microphone interface (PDM) 3x 32-bit timer with counter mode SPI master/slave with EasyDMA I2C compatible 2-wire master/slave UART (CTS/RTS) with EasyDMA Programmable peripheral interconnect (PPI) Quadrature decoder (QDEC) AES HW encryption with EasyDMA 2x real-time counter (RTC) Single crystal operation

Antenna information: Manufacture: OPTO Model No.: OPTO-BTM-02 Antenna Type: Printed Antenna Antenna Gain: 3.0 dBi

PIN ASSIGNMENT

LITE® i s Gomipme1Opa is Goenipansre1Opa 2 STDatESET Sm bararedebug d Ash x 2 Gomaipupse1Opn r 2 Gmenipapse1Opa r x pupoe10p r as Gomipmse10 r 2 xc 2 xc x NTDieestlammcmmint > in ppoet0 5 ppoet0 5 mipmserop a pupoet0 5s pupoet0 se al papose 1O pm 5 it papose 1O pa as it papose 1O pa e al papose 1O pa io VDDRower supply

LIVE DEMO Step1. Download Nordic APP (nRF UART or nRF Toolbox) Step2. Install

Step 3. Run APP(Connect to demo board ”Nordic UART”) (Demo boardconnected)

Step 4. RUN PC terminal tool( UART tool)

Step 5. Send string from PC to smartphone (ex: Hi Ted!)

Step 6. Received string on your smartphone (ex: Hi Ted!)

Step 7. Send string fromsmartphone to PC (ex: Hello Nordic!)

Step 8. Received string on your PC(ex: Hello Nordic!)


Document Created: 2019-10-30 09:23:07
Document Modified: 2019-10-30 09:23:07
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC