Users Manual

FCC ID: PPQ-CR8702K

Users Manual

Download: PDF
FCCID_1433733

Data Sheet: CR Series JukeBlox Networked Media Modules JukeBlox Networked Media Module CR Series CR870-2K Datasheet Complete audio networking system on a small module Integrated Ethernet + USB2.0 WiFi-certified 802.11b/g (optional) Built-in PIFA antenna DAB radio receiver (optional) Glueless audio, video and control ports FCC certified CONFIDENTIAL dat_CR860_CR870_2_14_datasheet.doc CONFIDENTIAL Version 2.14 – June 10th 2010 - Page 1 of 15

Data Sheet: CR Series JukeBlox Networked Media Modules Introduction The CR-series module is a single-board networked media player module, based on BridgeCo’s DM860 and DM870 media processors, and enables fast product developments with Ethernet, USB and optional WiFi and/or DAB radio connectivity. The module connects to standard legacy components in various audio, video/LCD and control formats. Block Diagram JukeBlox Networked Media Module – CR Series 3.3V JTAG 1.2V DM860 or 24.000 MHz DM870 Reset In Reset Out RST Ethernet 1 GB 100B-T RJ-45 PHY RMII NAND NAND flash 256 Mbit USB 5V Mem SDRAM USB (Host) USB 3x6bit RGB Display LCD 802.11 4/8bit MMC 802.11 RF amp SD-Card SSM (optional) Stereo Out 2 HP out LP DAC Video Out CCIR-656 AV PIFA Antenna A/D, D/A Audio I/O S/PDIF Ports Switcher 1.9V 2 x UART serial control UART shift register SPI Ctrl. IC control SPI AV IR sensor DAB reset signals max. 20 GPIOs Ports analog mute GPIO I2C bus 3.3V (RTC) SuperCap RTC 32.768 kHz dat_CR860_CR870_2_14_datasheet.doc CONFIDENTIAL Version 2.14 – June 10th 2010 - Page 2 of 15

Data Sheet: CR Series JukeBlox Networked Media Modules Overview Top View of CR870-2A version FLASH antenna (optional socket) SDRAM connector PIFA antenna 802.11b/g front-end DAB BridgeCo Ethernet processor Bottom View of CR870-2A version LCD connector DAB connector Media connector dat_CR860_CR870_2_14_datasheet.doc CONFIDENTIAL Version 2.14 – June 10th 2010 - Page 3 of 15

Data Sheet: CR Series JukeBlox Networked Media Modules Top View of CR870-2G version Bottom View of CR870-2B, CR870-2C, CR870-2G versions Please note that production version does not have exposed solder on the underside of the mounting holes. dat_CR860_CR870_2_14_datasheet.doc CONFIDENTIAL Version 2.14 – June 10th 2010 - Page 4 of 15

Data Sheet: CR Series JukeBlox Networked Media Modules Ordering Guide Ext. Real- DAB / PIFA Antenna No on-board WiFi Ethernet USB Time DAB+ / LCD SDRAM Antenna UFL 1.9V Part Clock DMB Audio Conn. Number BridgeCo ICs Contains Incl. Incl. shield connector connector CR870-2A DM870+T6201 X X X X X X X (X)* 32MB CR870-2B DM870+T6201 X X X X 32MB CR870-2C DM870+T6201 X X X 32MB CR870-2D DM870+T6201 X X X X X 32MB CR870-2F DM870+T6201 X X X X X X (X)* 32MB CR870-2G DM870+T6201 X X X X 32MB CR870-2H DM870+T6201 X X X X (X)* 16MB CR870-2I DM870+T6201 X X X 16MB CR870-2J DM870+T6201 X X X 16MB CR870-2K DM870+T6201 X X X 16MB X CR860-2A DM860 n/a X X n/a 32MB CR860-2B DM860 n/a X X X X n/a 32MB * Connector on board, but not enabled Electrical Specifications Parameter State Model Component Voltage Symbol min. typ. max. Units Input Voltage +2.97 +3.3 +3.63 V Main VIN +1.08 +1.2 +1.32 V +1.62 +1.8 +1.98 V DAB VIN +2.97 +3.3 +3.63 V +1.35 +1.5 +1.65 V Power Reset CR870 3.3V PIN3.3 - 230 300 mW Consumption State int 1.9V 1.2V PIN1.2 - 45 60 mW 3.3V PIN3.3 - 165 215 mW CR870 1.2V PIN1.2 - 45 60 mW ext 1.9V 1.9V PIN1.9 - 35 50 mW 3.3V PIN3.3 - 145 190 mW CR860 1.2V PIN1.2 - 45 60 mW Main WLAN CR870 3.3V PIN3.3 - 1750 2275 mW Operating int 1.9V 1.2V PIN1.2 - 600 800 mW 3.3V PIN3.3 - 825 1075 mW CR870 1.2V PIN1.2 - 600 800 mW ext 1.9V 1.9V PIN1.9 - 535 700 mW Operating 3.3V PIN3.3 - 760 990 mW CR860 1.2V PIN1.2 - 600 800 mW Note: The maximum power consumption values are 30% larger than the typical values. The maximum values are intended to be used for power supply sizing calculations. dat_CR860_CR870_2_14_datasheet.doc CONFIDENTIAL Version 2.14 – June 10th 2010 - Page 5 of 15

Data Sheet: CR Series JukeBlox Networked Media Modules Absolute Maximum Ratings Parameter Component Min Max Units 3.3V Supply Voltage -0.5 4.6 V 1.2V Supply Voltage -0.5 1.8 V Main Logic Input Voltage -0.5 6 V Logic Output Voltage -0.5 4.6 V Operating Conditions Parameter Min Max Units Operating Temperature 0 +70 °C Operating Humidity 10 90 (non condensing) %RH Storage Temperature -10 +75 °C Storage Humidity 10 95 (non condensing) %RH Storage Temperature Cycle Test 24 hrs -10 +75 °C WiFi Specification (CR870 only) Feature Description WLAN Standards IEEE 802.11b IEEE 802.11g Frequency Band 2.412 – 2.472 GHz (2.4GHz ISM Band, 13 Channels) Channel 1 - Channel 13 North America, Japan Telec, Europe ETSI Modulation 802.11b mode (DS-SS: IEEE 802.11b) 802.11g mode (OFDM: IEEE 802.11g) Transmission Speed 802.11b mode 11Mbps, 5.5Mbps, 1Mbps 802.11g mode 54Mbps, 48Mbps, 36Mbps, 24Mbps, 18Mbps, 12Mbps, 9Mbps, 6Mbps Tx Power 802.11b mode (16.5dBm, +/-1dBm) 802.11g mode (21dBm, +/-1dBm) Power-on Ramp < 2us RF Carrier Suppression < 15dBc TX EVM < -5dB @ 6Mbps < -25dB @ 54Mbps Rx Sensitivity 802.11b mode (incl. CE2 Mother board) =<-88dBm @ 1Mbps, =<-85dBm @ 5.5Mbps, =<-83dBm @ 11Mbps 802.11g mode =<-86dBm @ 6Mbps, =<-75dBm @ 36Mbps, =<-69dBm @ 54Mbps Throughput Rate See factory test specification (measured for each module) dat_CR860_CR870_2_14_datasheet.doc CONFIDENTIAL Version 2.14 – June 10th 2010 - Page 6 of 15

Data Sheet: CR Series JukeBlox Networked Media Modules Regulatory compliance Description Country Compliance Electromagnetic Compatibility USA FCC CFR47 Part15B (Prescan) Europe EN 55022 EN 55024 EN 61000-3-2 EN 61000-3-3 EN 61000-4-2 EN 61000-4-3 EN 61000-4-4 EN 61000-4-5 EN 61000-4-6 EN 61000-4-8 EN 61000-4-11 Radio Regulations (CM870 TBD TBD only) RoHS Uses only RoHS compliant components Environmental Test Withstands 4 hours at 70°C, 90% RH ESD and Transient Test (Applies to LAN and USB external connections only) ESD: +/- 2kV operation, +/- 4kV no destruction (part of CE test) Fast electrical transients: +/- 500V operation, +/- 1000V no destruction (part of CE test) Magnetic Field Test Passes EN55022 and EN55024 (part of CE test) MTBF >10000 hours Mechanical Specifications Passes drop test according to I.E.C. 68-2-32, height 100 cm, 1 corner, 6 faces. Passes vibration test with sine, vertical, 60 minutes, 600 to 18000 cpm, 1G Module Quality Defect Rate: 7 months <0.5% failures, 14 months <1% failures AQL CR=0, MA=0.4, MI=0.4 dat_CR860_CR870_2_14_datasheet.doc CONFIDENTIAL Version 2.14 – June 10th 2010 - Page 7 of 15

Data Sheet: CR Series JukeBlox Networked Media Modules Board Dimensions Top View and Side View Bottom View (showing connector locations) Note: 1. All dimensions are measured in millimetres (mm). 2. PCB’s thickness: 1.00 +/- 0.10mm 3. Tolerance: +/-0.10mm 4. Outline Tolerance: +/-0.10mm 5. NPTH Hole: +/-0.05mm 6. PTH Hole: +/-0.075mm 7. Connector positions, board dimensions, mounting hole positions and sizes are the same for all module variants. dat_CR860_CR870_2_14_datasheet.doc CONFIDENTIAL Version 2.14 – June 10th 2010 - Page 8 of 15

Data Sheet: CR Series JukeBlox Networked Media Modules Top and Side View of CR870-2G (no PIFA antenna) Module weight CR860: 25g CR870: 25g dat_CR860_CR870_2_14_datasheet.doc CONFIDENTIAL Version 2.14 – June 10th 2010 - Page 9 of 15

Data Sheet: CR Series JukeBlox Networked Media Modules Connectors WLAN UFL Antenna Connector (optional) One coaxial antenna connector is provided as an alternative to the built-in PIFA antenna. The choice between using the PIFA antenna or using the coaxial socket is a build option, determined by the position of a surface mount capacitor on the module PCB. Please see ordering guide for build option details. The surface-mount receptacle parts: Hirose U.FL-R-SMT (CL No. 331-0471-0) Coaxial antenna connector dimensions Module Connectors The CR860/870 module uses 3 female board-to-board connectors as interfaces to the product main board. The connectors needed on the product main board are male type, with the part numbers as shown in the table below. Connector Connector Connector Number Pin Male Mating Connector Part Number Purpose Type of Pins Configuration Numbers J1 LCD 30 2 x 15 x 0.5mm 14-5046-030-145-829+ (Kyocera) B2B J2 Media 120 2 x 60 x 0.5mm 14-5046-120-145-829+ (Kyocera) Connector J3 DAB 40 2 x 20 x 0.5mm 14-5046-040-145-829+ (Kyocera) dat_CR860_CR870_2_14_datasheet.doc CONFIDENTIAL Version 2.14 – June 10th 2010 - Page 10 of 15

Data Sheet: CR Series JukeBlox Networked Media Modules The pinout and signal names are shown on the next page. The following table provides an overview for the most important control and interface signals. Key Connections Signal(s) Connector ID Pin Description Number(s) VIN J2 3, 4, 5, 6 Input voltage; +3.3V J2 9, 10, 11, 12 Input voltage; +1.2V J3 4, 6 Input voltage; +1.8V J3 10 Input voltage; +3.3V J3 12 Input voltage; +1.5V SPI_DOUT J2 25 SPI bus from DM870’s SPI controller. SPI_DIN J2 27 SPI_CLK J2 29 SPI_NCS0, 1 J2 30, 32 SPI_REQ J2 64 PDOUT1 signal used as SPI_REQ for eDMP applications RXD1, TXD1 J2 35, 37 3.3V logic level UART I/Os for the debug UART. Provide external RS-232 transceiver to connect to a PC’s COM port. NRESET_MOD J2 34 Low-active input to reset the module; internal 10K pull-up NPD_RF J2 119 Low-active input to shut down the power for the 802.11 Rf part; internal 10K pull-up AOUTLP/AOUTLN J2 63, 65 Differential stereo output from PWM-DAC. AOUTRP/AOUTRN J2 60, 58 BIST activate J2 48 Low-active input to invoke the production BIST; DM870-internal pull-up Factory Reset J2 68 High-active input to reset the configuration; DM870-internal pull-down IR input J2 70 Infrared sensor input. This is a Schmitt-Trigger input and can handle interrupt inputs with slow slopes. ETH_NRESET J2 72 Low-active reset for the on-board Ethernet phy. This output is driven by the DM870 and is not suited for other purpose. SDA, SCL J2 73, 75 I2C bus created by GPIO-14 and GPIO-13. No internal pull-ups; if I2C is to be used, please add the proper external pull-up resistors. ETH_LED_ACT J2 100 3.3V push-pull outputs (max. ±12mA) to drive the ETH_LED_SPEED J2 102 Ethernet LEDs. A low-level indicates 100Mbps mode and activity respectively. dat_CR860_CR870_2_14_datasheet.doc CONFIDENTIAL Version 2.14 – June 10th 2010 - Page 11 of 15

Data Sheet: CR Series JukeBlox Networked Media Modules Detailed Connector PIN Descriptions J2 – Media Connector Function GPIO Signal IC PIN Power PIN Number Power IC PIN Signal GPIO Function GND 1 2 GND VIN (+3.3V) 3 4 VIN (+3.3V) VIN (+3.3V) 5 6 VIN (+3.3V) GND 7 8 GND VIN (+1.2V) 9 10 VIN (+1.2V) VIN (+1.2V) 11 12 VIN (+1.2V) GND 13 14 GND VIN_OUTSIDE (+1.9V) 15 16 VIN_OUTSIDE (+1.9V) GND 17 18 GND F4 3V3RTC 19 20 GND GND 21 22 B20 TMS GND 23 24 A20 TCK JTAG SPI_DOUT E17 25 26 B19 TDI SPI SPI_DIN F17 27 28 A19 TDO SPI_CLK D17 29 30 D16 SPI_NCS0 SPI TXD0 C17 31 32 D15 SPI_NCS1 RXD0 A18 33 34 NRESET_MOD RXD1 B17 35 36 B16 SSMD6 GPIO-10 SPI_E_CLK Debug UART TXD1 A17 37 38 C15 SSMD4 GPIO-08 SPI_E_SDO GND 39 40 A15 SSMD2 SPI_E_NCS GPIO-11 SSMD7 C16 41 42 C14 SSMD1 SPI_E_SDI GPIO-09 SSMD5 A16 43 44 A14 SSMCMD SSMD3 B15 45 46 C11 SSMWP SSMD0 B14 47 48 M18 NCS3 GPIO-17 BIST activate SSMCLK C13 49 50 L18 NCS2 GPIO-19 SSMCP C12 51 52 GND GND 53 54 USB_VBUS USB USB_DN A1 55 56 GND USB USB_DP B1 57 58 K2 AOUTRN USBVBUSDRV 59 60 J2 AOUTRP GND 61 62 GND AOUTLP H3 63 64 L1 PDOUT1 GPIO-06 SPI_REQ AOUTLN J3 65 66 L2 VCO1 GPIO-07 GND 67 68 M1 PDOUT0 GPIO-04 Factory reset GPIO-16 A23 K20 69 70 M2 VCO0 GPIO-05 IR input IRQ input GPIO-18 A22 K19 71 72 U3 AV3CLK GPIO-12 ETH NRESET I2C SDA GPIO-14 AV3CTRL1 V1 73 74 M3 AV0CTRL0 I2C SCL GPIO-13 AV3CTRL0 V2 75 76 P3 AV1DATA3 AV0CTRL2 K3 77 78 R1 AV1DATA2 Video Output AV0CTRL1 L3 79 80 R2 AV1DATA1 AV0CLK N1 81 82 R3 AV1DATA0 Video Output AV0DATA3 N2 83 84 GND AV0DATA2 N3 85 86 T1 AV2CTRL1 MCLK AV0DATA1 P1 87 88 GND AV0DATA0 P2 89 90 R4 AV2CLK SCLK GND 91 92 GND LRCK AV2CTRL0 T2 93 94 W2 AV4DATA1 SPDIF output A/D data 1 AV2DATA3 T3 95 96 Y1 AV4DATA0 SPDIF input A/D data 0 AV2DATA2 T4 97 98 GND D/A data 1 AV2DATA1 U1 99 100 ETH_LED_ACT Ethernet D/A data 0 AV2DATA0 U2 101 102 ETH_LED_SPEED GND 103 104 Y14 MIICRS GPIO-00 ETH_RX- 105 106 W14 MIICOL GPIO-01 ETH_RX+ 107 108 V10 MIITXER GPIO-02 Ethernet ETH_CT 109 110 V11 MIITXCLK GPIO-03 ETH_TX- 111 112 W10 MIITXD0 ETH_TX+ 113 114 Y10 MIITXD1 GND 115 116 W12 MIIRXD0 GPIO-15 NWAIT N18 117 118 Y12 MIIRXD1 NPD_RF 119 120 GND dat_CR860_CR870_2_14_datasheet.doc CONFIDENTIAL Version 2.14 – June 10th 2010 - Page 12 of 15

Data Sheet: CR Series JukeBlox Networked Media Modules J1 – LCD Connector Function GPIO Signal IC PIN Power PIN Number Power IC PIN Signal GPIO Function GND 1 2 GND LCDD0 Y7 3 4 W7 LCDD1 LCDD2 V7 5 6 Y6 LCDD3 LCDD4 W6 7 8 V6 LCDD5 LCDD6 U6 9 10 Y5 LCDD7 LCD Interface LCDD8 W5 11 12 V5 LCDD9 LCD Interface LCDD10 U5 13 14 Y4 LCDD11 LCDD12 W4 15 16 V4 LCDD13 LCDD14 U4 17 18 Y3 LCDD15 LCDD16 W3 19 20 Y2 LCDD17 GND 21 22 GND LCDCLK Y9 23 24 W9 LCDCTRL0 LCD Interface LCD Interface LCDCTRL1 Y8 25 26 W8 LCDCTRL2 LCDCTRL3 V8 27 28 GND GND 29 30 GND J3 – DAB Connector Function GPIO Signal PNM3030E PIN Power PIN Number Power PNM3030E PIN Signal GPIO Function GND 1 2 GND RESETB 30 3 4 VIN (+1.8V) RF_I2C_CK 39 5 6 VIN (+1.8V) I2C_SDA_DAB 3 7 8 40 RF_I2C_DT I2C_SCL_DAB 46 9 10 VIN (+3.3V) GND 11 12 VIN (+1.5V) TEST_1 79 13 14 80 TEST_2 DAB_SPI_MOSI 19 15 16 78 TEST_0 SPI DAB_SPI_CSB 17 17 18 18 DAB_SPI_CLK SPI GND 19 20 16 DAB_SPI_MISO GND 21 22 GND GND 23 24 14 INT_0 GND 25 26 15 INT_1 MPEG_ERR 4 27 28 47 MPEG_CLK MPEG_SYNC 5 29 30 48 MPEG_VAL MPEG_DAT7 6 31 32 7 MPEG_DAT6 MPEG_DAT5 51 33 34 8 MPEG_DAT4 MPEG_DAT3 52 35 36 9 MPEG_DAT2 MPEG_DAT1 10 37 38 53 MPEG_DAT0 GND 39 40 GND Application Notes There are strict power sequencing and reset timing requirements. Please see DM870 IC data sheet, Sections 3.1 and 3.2, filename: dat_DM870_16_datasheet.pdf, or later version. dat_CR860_CR870_2_14_datasheet.doc CONFIDENTIAL Version 2.14 – June 10th 2010 - Page 13 of 15

Data Sheet: CR Series JukeBlox Networked Media Modules Revision Control Revision Date / Author Remarks V2.14 June 10, 2010 / SHs • Updated Frequency Band entry in “WiFi Specification” table V2.13 June 6, 2010 / SHs • Updated “Ordering Guide” table V2.12 May 27, 2010 / SHs • Updated TX EVM entry in “WiFi Specifications” table • Updated Power Consumption entries in “Electrical Specifications” table • Added Note to “Electrical Specifications” table • Removed box from “Bottom View of CR870-2C version” photo • Updated “Bottom View of CR870-2C version” title to “Bottom View of CR870-2B, CR870-2C, CR870-2G versions” • Added “Top View of CR870-2G version” photo • Updated “Top View” title to “Top View of CR870-2A version” • Updated “Bottom View” to “Bottom View of CR870-2A version” • Updated Notes in Board Dimensions section • Added “Top and Side View of CR870-2G” drawings • Updated Module Weight titles V2.11 April 25, 2010 / SHs • Updated Power Consumption/WLAN Operating entry in “Electrical Specifications” table V2.10 April 10, 2010 / SHs • Corrected “Module Connectors” section text to say “female board-to-board connectors” • Updated Module Connectors table with correct “Male” Mating Connector Part Numbers V2.9 March 22, 2010 / SHs • Renamed “WLAN Antenna Connectors” section to “WLAN UFL Antenna Connector” • In the “WLAN Antenna Connectors” table, “receptible” became “receptacle” • CR870-2G option and External Antenna UFL connector column added to Ordering Guide • Power Consumption values added to Electrical Specifications table • Added Absolute Maximum Ratings table • Added Application Notes section • NREST became NRESET_MOD for Pin 34 in Key Connections table • SPI_REQ row added to Key Connections table • SPI_REQ added to Function column of Pin 64 in J2-Media Connector table V2.8 Feb. 24, 2010 / SHs • Added “Bottom View of CR870-2C version” image to “Overview” section V2.7 Feb. 16, 2010 / SHs • Updated “Module Connectors” table V2.6 Feb. 15, 2010 / SHs • Updated “Ordering Guide” table V2.5 Feb. 10, 2010 / SHs • Updated “Ordering Guide” table • Added new coaxial text in “WLAN Antenna Connectors” section • Added manufacturer name to “Module Connectors” table V2.4 Feb. 08, 2010 / SHs • Updated Rx Sensitivity description in “WiFi Specification” table V2.3 Feb. 03, 2010 / SHs • “Key Connectors” table title changed to “Key Connections” • Updated entries in “Key Connections” table • Updated pins 1, 2, 25, 27, 58 & 60 in “J2 – Media Connector” table dat_CR860_CR870_2_14_datasheet.doc CONFIDENTIAL Version 2.14 – June 10th 2010 - Page 14 of 15

Data Sheet: CR Series JukeBlox Networked Media Modules V2.2 Feb. 02, 2010 / SHs • Added new items to “WiFi Specification” table • Amended Block Diagram to show input of 1.2V instead of 1.8V V2.1 Jan. 04, 2010 / SHs • Updated header layout • Removed “CR860/CR870” from data sheet title • Left justified Key Features list on front page • New Ordering Guide table • Updated Module Weights V2.0 Jan. 02, 2010 / JWs and • New header and footer layout SHs • Fit front and back Overview images onto one page • Bulletise Revision Control table V1.1 Dec. 18, 2009 / SHs • Changed Core Module name to “JukeBlox Networked Media Module(CR Series)” • Front page revisions: removed front and back images of board; inserted angled image of board; moved Key Features list to front page • Moved Disclaimers page to end of document • Replaced previous board images (front and back) in Overview section with better quality images • Added box and label to BridgeCo processor in Overview images • Revised Ordering Guide • Reduced Board Dimension drawings to fit on one page • Added mating connector part numbers to Module Connectors section. V1.0 Dec. 9, 2009 / SHs Initial version © 2010 by BridgeCo Inc All rights reserved. This document is the sole property of BridgeCo. It contains information proprietary to BridgeCo. Reproduction or duplication by any means of any portion of this document without the prior written consent of BridgeCo is expressly forbidden. Trademarks The names of products of BridgeCo or other vendors and suppliers appearing in this document may be trademarks or service marks of their respective owners which may be registered in some jurisdictions. Warranty Limitations BridgeCo assumes no responsibility for inaccuracies, errors, or omissions in this document. BridgeCo assumes no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change without notice. Module Revision History To be determined. dat_CR860_CR870_2_14_datasheet.doc CONFIDENTIAL Version 2.14 – June 10th 2010 - Page 15 of 15

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning "Industry Canada regulatory information Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. ""The user is cautioned that this device should be used only as specified within this manual to meet RF exposure requirements. Use of this device in a manner inconsistent with this manual could lead to excessive RF exposure conditions." IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This device is intended only for OEM integrators under the following conditions: - The antenna must be installed such that 20 cm is maintained between the antenna and users. Information To Be Supplied to the End User by the OEM or Integrator The following regulatory and safety notices must be published in documentation supplied to the end user of the product or system incorporating an adapter in compliance with local regulations. Host system must be labeled with "Contains FCCID:PPQ-CR8702K“, FCC ID displayed on label.


Document Created: 2011-03-09 13:36:38
Document Modified: 2011-03-09 13:36:38
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC