modular approval letter

FCC ID: PPQ-AWOXMII2

Cover Letter(s)

Download: PDF
FCCID_1625816

RF_734_00, Issue 1 Modular Approval Request FCC (per DA 00-1407) FCC ID: PPQ-AWOXMII2 Items to be covered Answer from applicant 1. The modular transmitter must have its own RF shielding. Please review external photos. 2. The modular transmitter must have buffered modulation/data inputs (if such inputs The buffered integrated in are provided) to ensure that the module will comply with Part 15 requirements chip RT3052. under conditions of excessive data rates or over-modulation. 3. The modular transmitter must have its own power supply regulation. There are regulators in front of these chips; the part number of this regulator is SY8009AAAC. 4. The modular transmitter must comply with the antenna requirements of Section Please review external photos 15.203 and 15.204(c). The antenna must either be permanently attached or employ or test report. a “unique” antenna coupler (at all connections between the module and the antenna, including the cable).. 5. The modular transmitter must be tested in a stand-alone configuration, i.e., the Please review test setup module must not be inside another device during testing. This is intended to photos. demonstrate that the module is capable of complying with Part 15 emission limits regardless of the device into which it is eventually installed. 6. The modular transmitter must be labeled with its own FCC ID number, and, if the Please review label sample. FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: XYZMODEL1” or “Contains FCC ID: XYZMODEL1.” Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. 7. The modular transmitter must comply with any specific rule or operating The EUT is compliant with all requirements applicable to the transmitter and the manufacturer must provide applicable FCC rules. Detail adequate instructions along with the module to explain any such requirements. A instructions for maintaining copy of these instructions must be included in the application for equipment compliance are given in the authorization. For example, there are very strict operational and timing Users Manual. requirements that must be met before a transmitter is authorized for operation under Section 15.231. For instance, data transmission is prohibited, except for operation under Section 15.231(e), in which case there are separate field strength level and timing requirements. Compliance with these requirements must be assured. 8. The modular transmitter must comply with any applicable RF exposure The EUT is compliant with all requirements. For example, FCC Rules in Sections 2.1091, 2.1093 and specific applicable RF exposure Sections of Part 15, including 15.319(i), 15.407(f), 15.253(f) and 15.255(g), requirements. RF Exposure is require that Unlicensed PCS, UNII and millimeter wave devices perform routine addressed in the RF exposure environmental evaluation for RF Exposure to demonstrate compliance. In exhibition. addition, spread spectrum transmitters operating under Section 15.247 are required to address RF Exposure compliance in accordance with Section 15.247(b)(4). Modular transmitters approved under other Sections of Part 15, when necessary, may also need to address certain RF Exposure concerns, typically by providing specific installation and operating instructions for users, installers and other interested parties to ensure compliance. Note: If compliance with one or more of the numbered requirements, listed above, cannot be demonstrated, it may be possible to obtain a “Limited Modular Approval” (LMA). Name and surname of applicant (or authorized representative): TC Wu / Director Date: Dec.30, 2011 Signature:


Document Created: 2012-01-19 18:16:48
Document Modified: 2012-01-19 18:16:48
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC