(A5) TestRpt-Part 2

FCC ID: PPQ-A5

Test Report

Download: PDF
FCCID_1729562

Report No. 124188R-RFUSP42V01 6. Band Edge 6.1. Test Equipment RF Conducted Measurement The following test equipments are used during the band edge tests: Equipment Manufacturer Model No./Serial No. Last Cal. Spectrum Analyzer R&S FSP40 / 100170 Jun, 2011 Spectrum Analyzer Agilent E4407B / US39440758 Jun, 2011 X Spectrum Analyzer Agilent N9010A / MY48030495 Apr., 2012 Note: 1. All equipments are calibrated with traceable calibrations. Each calibration is traceable to the national or international standards. 2. The test instruments marked with “X” are used to measure the final test results. RF Radiated Measurement: The following test equipments are used during the band edge tests: Test Site Equipment Manufacturer Model No./Serial No. Last Cal. Site # 3 Bilog Antenna Schaffner Chase CBL6112B/2673 Sep., 2011 X Horn Antenna Schwarzbeck BBHA9120D/D305 Sep., 2011 Horn Antenna Schwarzbeck BBHA9170/208 Jul., 2011 X Pre-Amplifier Agilent 8447D/2944A09549 Sep., 2011 X Spectrum Analyzer Agilent E4407B / US39440758 May, 2011 Test Receiver R&S ESCS 30/ 825442/018 Sep., 2011 X Coaxial Cable QuieTek QTK-CABLE/ CAB5 Feb., 2012 X Controller QuieTek QTK-CONTROLLER/ CTRL3 N/A X Coaxial Switch Anritsu MP59B/6200265729 N/A Note: 1. All instruments are calibrated every one year. 2. The test instruments marked by “X” are used to measure the final test results. Page: 47 of 72

Report No. 124188R-RFUSP42V01 6.2. Test Setup RF Conducted Measurement: RF Cable EUT Spectrum Analyzer SMA RF Radiated Measurement: 3m FRP Dome The height of broad band or Dipole Antenna was scanned from 1M to 4M. The distance between EUT antenna and turn table was 3M regards to the standard adopted. 80cm To Receiver Pre- Amplifier 6.3. Limits Emissions radiated outside of the specified frequency bands, except for harmonics, shall be attenuated by at least 20dB below the level of the fundamental or to the general radiated emission limits in paragraph 15.209, whichever is the lesser attenuation. Page: 48 of 72

Report No. 124188R-RFUSP42V01 6.4. Test Procedure The EUT was setup according to ANSI C63.4, 2003 and tested according to DTS test procedure of Jan. 2012 KDB558074 for compliance to FCC 47CFR 15.247 requirements. The EUT is placed on a turn table which is 0.8 meter above ground. The turn table is rotated 360 degrees to determine the position of the maximum emission level. The EUT was positioned such that the distance from antenna to the EUT was 3 meters. The antenna is scanned from 1 meter to 4 meters to find out the maximum emission level. This is repeated for both horizontal and vertical polarization of the antenna. In order to find the maximum emission, all of the interface cables were manipulated according to ANSI C63.4:2003 on radiated measurement. 6.5. Uncertainty ± 3.9 dB above 1GHz ± 3.8 dB below 1GHz Page: 49 of 72

Report No. 124188R-RFUSP42V01 6.6. Test Result of Band Edge Product : Wireless Music System Test Item : Band Edge Data Test Site : No.3 OATS Test Mode : Mode 1: Transmit (802.11b 1Mbps) Fundamental Filed Strength Antenna Frequency Correction Factor Reading Level Emission Level Detector Pole [MHz] [dB/m] [dBuV] [dBuV/m] Horizontal 2412 31.646 72.616 104.262 Peak Horizontal 2412 31.66 68.804 100.464 Average Vertical 2412 30.956 77.025 107.981 Peak Vertical 2412 30.968 73.224 104.192 Average Note: 1:Spectrum Analyzer setting: Peak detector: RBW=1MHz, VBW=1MHz Average detector: RBW=1MHz, VBW=10Hz Band Edge Test Data Test Band Edge Antenna Fundamental Limit Frequency Δ (dB) Field Strength Detector Pole (dBuV/m) (dBuV/m) (MHz) (dBuV/m) Horizontal 2386.3 104.262 43.18 61.082 74.000 Peak Horizontal 2386.6 100.464 50.373 50.091 54.000 Average Vertical 2386.3 107.981 43.18 64.801 74.000 Peak Vertical 2386.6 104.192 50.373 53.819 54.000 Average Note: The Band Edge Field Strength was calculated using the Fundamental and Conducted Band Edge measurements per the Marker-Delta Method with the following formula: Band Edge field Strength = F - Δ F = Fundamental field Strength (Peak or Average) Δ = Conducted Band Edge Delta (Peak or Average) Page: 50 of 72

Report No. 124188R-RFUSP42V01 Peak Detector of conducted Band Edge Delta Average Detector of conducted Band Edge Delta Page: 51 of 72

Report No. 124188R-RFUSP42V01 Product : Wireless Music System Test Item : Band Edge Data Test Site : No.3 OATS Test Mode : Mode 1: Transmit (802.11b 1Mbps) Fundamental Filed Strength Antenna Frequency Correction Factor Reading Level Emission Level Detector Pole [MHz] [dB/m] [dBuV] [dBuV/m] Horizontal 2462 32.026 68.293 100.319 Peak Horizontal 2462 32.013 64.686 96.699 Average Vertical 2462 31.296 74.987 106.283 Peak Vertical 2462 31.285 71.291 102.575 Average Note: 1:Spectrum Analyzer setting: Peak detector: RBW=1MHz, VBW=1MHz Average detector: RBW=1MHz, VBW=10Hz Band Edge Test Data Test Band Edge Antenna Fundamental Limit Frequency Δ (dB) Field Strength Detector Pole (dBuV/m) (dBuV/m) (MHz) (dBuV/m) Horizontal 2490.2 100.319 41.437 58.882 74.000 Peak Horizontal 2488 96.699 50.883 45.816 54.000 Average Vertical 2490.2 106.283 41.437 64.846 74.000 Peak Vertical 2488 102.575 50.883 51.692 54.000 Average Note: The Band Edge Field Strength was calculated using the Fundamental and Conducted Band Edge measurements per the Marker-Delta Method with the following formula: Band Edge field Strength = F - Δ F = Fundamental field Strength (Peak or Average) Δ = Conducted Band Edge Delta (Peak or Average) Page: 52 of 72

Report No. 124188R-RFUSP42V01 Peak Detector of conducted Band Edge Delta Average Detector of conducted Band Edge Delta Page: 53 of 72

Report No. 124188R-RFUSP42V01 Product : Wireless Music System Test Item : Band Edge Data Test Site : No.3 OATS Test Mode : Mode 2: Transmit (802.11g 6Mbps) Fundamental Filed Strength Antenna Frequency Correction Factor Reading Level Emission Level Detector Pole [MHz] [dB/m] [dBuV] [dBuV/m] Horizontal 2412 31.67 71.107 102.776 Peak Horizontal 2412 31.598 56.702 88.301 Average Vertical 2412 30.977 78.592 109.568 Peak Vertical 2412 30.932 63.297 94.23 Average Note: 1:Spectrum Analyzer setting: Peak detector: RBW=1MHz, VBW=1MHz Average detector: RBW=1MHz, VBW=10Hz Band Edge Test Data Test Band Edge Antenna Fundamental Limit Frequency Δ (dB) Field Strength Detector Pole (dBuV/m) (dBuV/m) (MHz) (dBuV/m) Horizontal 2388.9 102.776 37.88 64.896 74.000 Peak Horizontal 2390 88.301 40.42 47.881 54.000 Average Vertical 2388.9 109.568 37.88 71.688 74.000 Peak Vertical 2390 94.23 40.42 53.81 54.000 Average Note: The Band Edge Field Strength was calculated using the Fundamental and Conducted Band Edge measurements per the Marker-Delta Method with the following formula: Band Edge field Strength = F - Δ F = Fundamental field Strength (Peak or Average) Δ = Conducted Band Edge Delta (Peak or Average) Page: 54 of 72

Report No. 124188R-RFUSP42V01 Peak Detector of conducted Band Edge Delta Average Detector of conducted Band Edge Delta Page: 55 of 72

Report No. 124188R-RFUSP42V01 Product : Wireless Music System Test Item : Band Edge Data Test Site : No.3 OATS Test Mode : Mode 2: Transmit (802.11g 6Mbps) Fundamental Filed Strength Antenna Frequency Correction Factor Reading Level Emission Level Detector Pole [MHz] [dB/m] [dBuV] [dBuV/m] Horizontal 2462 32.002 72.313 104.315 Peak Horizontal 2462 31.998 56.339 88.336 Average Vertical 2462 31.307 77.069 108.376 Peak Vertical 2462 31.281 61.076 92.357 Average Note: 1:Spectrum Analyzer setting: Peak detector: RBW=1MHz, VBW=1MHz Average detector: RBW=1MHz, VBW=10Hz Band Edge Test Data Test Band Edge Antenna Fundamental Limit Frequency Δ (dB) Field Strength Detector Pole (dBuV/m) (dBuV/m) (MHz) (dBuV/m) Horizontal 2485 104.315 38.267 66.048 74.000 Peak Horizontal 2483.5 88.336 40.529 47.807 54.000 Average Vertical 2485 108.376 38.267 70.109 74.000 Peak Vertical 2483.5 92.357 40.529 51.828 54.000 Average Note: The Band Edge Field Strength was calculated using the Fundamental and Conducted Band Edge measurements per the Marker-Delta Method with the following formula: Band Edge field Strength = F - Δ F = Fundamental field Strength (Peak or Average) Δ = Conducted Band Edge Delta (Peak or Average) Page: 56 of 72

Report No. 124188R-RFUSP42V01 Peak Detector of conducted Band Edge Delta Average Detector of conducted Band Edge Delta Page: 57 of 72

Report No. 124188R-RFUSP42V01 7. Occupied Bandwidth 7.1. Test Equipment Equipment Manufacturer Model No./Serial No. Last Cal. Spectrum Analyzer R&S FSP40 / 100170 Jun, 2011 Spectrum Analyzer Agilent E4407B / US39440758 Jun, 2011 X Spectrum Analyzer Agilent N9010A / MY48030495 Apr., 2012 Note: 1. All equipments are calibrated with traceable calibrations. Each calibration is traceable to the national or international standards. 2. The test instruments marked with “X” are used to measure the final test results. 7.2. Test Setup RF Cable EUT Spectrum Analyzer SMA 7.3. Limits The minimum bandwidth shall be at least 500 kHz. 7.4. Test Procedure The EUT was setup according to ANSI C63.4, 2003; tested according to DTS test procedure of Jan. 2012 KDB558074 for compliance to FCC 47CFR 15.247 requirements. Set RBW = 1-5% of the emission bandwidth, VBW≥3*RBW 7.5. Uncertainty ± 150Hz Page: 58 of 72

Report No. 124188R-RFUSP42V01 7.6. Test Result of Occupied Bandwidth Product : Wireless Music System Test Item : Occupied Bandwidth Data Test Site : No.3 OATS Test Mode : Mode 1: Transmit (802.11b 1Mbps) (2412MHz) Frequency Measurement Level Required Limit Channel No. Result (MHz) (kHz) (kHz) 1 2412 10200 >500 Pass Figure Channel 1: Page: 59 of 72

Report No. 124188R-RFUSP42V01 Product : Wireless Music System Test Item : Occupied Bandwidth Data Test Site : No.3 OATS Test Mode : Mode 1: Transmit (802.11b 1Mbps) (2437MHz) Frequency Measurement Level Required Limit Channel No. Result (MHz) (kHz) (kHz) 6 2437 12200 >500 Pass Figure Channel 6: Page: 60 of 72

Report No. 124188R-RFUSP42V01 Product : Wireless Music System Test Item : Occupied Bandwidth Data Test Site : No.3 OATS Test Mode : Mode 1: Transmit (802.11b 1Mbps) (2462MHz) Frequency Measurement Level Required Limit Channel No. Result (MHz) (kHz) (kHz) 11 2462 12200 >500 Pass Figure Channel 11: Page: 61 of 72

Report No. 124188R-RFUSP42V01 Product : Wireless Music System Test Item : Occupied Bandwidth Data Test Site : No.3 OATS Test Mode : Mode 2: Transmit (802.11g 6Mbps) (2412MHz) Frequency Measurement Level Required Limit Channel No. Result (MHz) (kHz) (kHz) 1 2412 16450 >500 Pass Figure Channel 1: Page: 62 of 72

Report No. 124188R-RFUSP42V01 Product : Wireless Music System Test Item : Occupied Bandwidth Data Test Site : No.3 OATS Test Mode : Mode 2: Transmit (802.11g 6Mbps) (2437MHz) Frequency Measurement Level Required Limit Channel No. Result (MHz) (kHz) (kHz) 6 2437 16450 >500 Pass Figure Channel 6: Page: 63 of 72

Report No. 124188R-RFUSP42V01 Product : Wireless Music System Test Item : Occupied Bandwidth Data Test Site : No.3 OATS Test Mode : Mode 2: Transmit (802.11g 6Mbps) (2462MHz) Frequency Measurement Level Required Limit Channel No. Result (MHz) (kHz) (kHz) 11 2462 16450 >500 Pass Figure Channel 11: Page: 64 of 72

Report No. 124188R-RFUSP42V01 8. Power Density 8.1. Test Equipment Equipment Manufacturer Model No./Serial No. Last Cal. Spectrum Analyzer R&S FSP40 / 100170 Jun, 2011 Spectrum Analyzer Agilent E4407B / US39440758 Jun, 2011 X Spectrum Analyzer Agilent N9010A / MY48030495 Apr., 2012 Note: 1. All equipments are calibrated with traceable calibrations. Each calibration is traceable to the national or international standards. 2. The test instruments marked with “X” are used to measure the final test results. 8.2. Test Setup RF Cable EUT Spectrum Analyzer SMA 8.3. Limits The transmitted power density averaged over any 1 second interval shall not be greater +8dBm in any 3kHz bandwidth. 8.4. Test Procedure The EUT was setup according to ANSI C63.4, 2003; tested according to DTS test procedure of Jan. 2012 KDB558074 for compliance to FCC 47CFR 15.247 requirements. Set RBW= 100 kHz, VBW≥300KHz, SPAN to 5-30 % greater than the EBW, Scale the observed power level to an equivalent value in 3 kHz by adjusting (reducing) the measured power by a bandwidth correction factor (BWCF) where BWCF = 10log (3 kHz/100 kHz = -15.2 dB). 8.5. Uncertainty ± 1.27 dB Page: 65 of 72

Report No. 124188R-RFUSP42V01 8.6. Test Result of Power Density Product : Wireless Music System Test Item : Power Density Data Test Site : No.3 OATS Test Mode : Mode 1: Transmit (802.11b 1Mbps) (2412MHz) Frequency Measure Level Limit Channel No. Result (MHz) (dBm) (dBm) 1 2412 -8.488 < 8dBm Pass Figure Channel 1: Page: 66 of 72

Report No. 124188R-RFUSP42V01 Product : Wireless Music System Test Item : Power Density Data Test Site : No.3OATS Test Mode : Mode 1: Transmit (802.11b 1Mbps) (2437MHz) Frequency Measurement Level Required Limit Channel No. Result (MHz) (dBm) (dBm) 6 2437 -8.311 < 8dBm Pass Figure Channel 6: Page: 67 of 72

Report No. 124188R-RFUSP42V01 Product : Wireless Music System Test Item : Power Density Data Test Site : No.3 OATS Test Mode : Mode 1: Transmit (802.11b 1Mbps) (2462MHz) Frequency Measurement Level Required Limit Channel No. Result (MHz) (dBm) (dBm) 11 2462 -10.871 < 8dBm Pass Figure Channel 11: Page: 68 of 72

Report No. 124188R-RFUSP42V01 Product : Wireless Music System Test Item : Power Density Data Test Site : No.3 OATS Test Mode : Mode 2: Transmit (802.11g 6Mbps) (2412MHz) Frequency Measure Level Limit Channel No. Result (MHz) (dBm) (dBm) 1 2412 -10.871 < 8dBm Pass Figure Channel 1: Page: 69 of 72

Report No. 124188R-RFUSP42V01 Product : Wireless Music System Test Item : Power Density Data Test Site : No.3OATS Test Mode : Mode 2: Transmit (802.11g 6Mbps) (2437MHz) Frequency Measurement Level Required Limit Channel No. Result (MHz) (dBm) (dBm) 6 2437 -10.857 < 8dBm Pass Figure Channel 6: Page: 70 of 72

Report No. 124188R-RFUSP42V01 Product : Wireless Music System Test Item : Power Density Data Test Site : No.3 OATS Test Mode : Mode 2: Transmit (802.11g 6Mbps) (2462MHz) Frequency Measurement Level Required Limit Channel No. Result (MHz) (dBm) (dBm) 11 2462 -11.437 < 8dBm Pass Figure Channel 11: Page: 71 of 72

Report No. 124188R-RFUSP42V01 9. EMI Reduction Method During Compliance Testing No modification was made during testing. Page: 72 of 72


Document Created: 2012-06-19 12:03:52
Document Modified: 2012-06-19 12:03:52
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC