QCNFA364A_TestRpt_RFExp_Part2 Rev. 01

FCC ID: PPD-QCNFA364AH

RF Exposure Info

Download: PDF
FCCID_3350837

Schmid & Partner Engineering AG s J e a g Zeughausstrasse 43, 8004 Zurich, Switzerland Phone +41 44 245 9700, Fax +41 44 245 9779 info@speag.com, http://www.speag.com IMPORTANT NOTICE USAGE OF THE DAE 4 The DAE unit is a delicate, high precision instrument and requires careful treatment by the user. There are no serviceable parts inside the DAE. Special attention shall be given to the following points: Battery Exchange: The battery cover of the DAE4 unit is closed using a screw, over tightening the screw may cause the threads inside the DAE to wear out. Shipping of the DAE: Before shipping the DAE to SPEAG for calibration, remove the batteries and pack the DAE in an antistatic bag. This antistatic bag shall then be packed into a larger box or container which protects the DAE from impacts during transportation. The package shall be marked to indicate that a fragile instrument is inside. E—Stop Failures. Touch detection may be malfunctioning due to broken magnets in the E—stop. Rough handling of the E—stop may lead to damage of these magnets. Touch and collision errors are often caused by dust and dirt accumulated in the E—stop. To prevent E—stop failure, the customer shall always mount the probe to the DAE carefully and keep the DAE unit in a non—dusty environment if not used for measurements. Repair: Minor repairs are performed at no extra cost during the annual calibration. However, SPEAG reserves the right to charge for any repair especially if rough unprofessional handling caused the defect. DASY Configuration Files: Since the exact values of the DAE input resistances, as measured during the calibration procedure of a DAE unit, are not used by the DASY software, a nominal value of 200 MOhm is given in the corresponding configuration file. Important Note: Warranty and calibration is void if the DAE unit is disassembled partly or fully by the Customer. Important Note: Never attempt to grease or oil the E—stop assembly. Cleaning and readjusting of the E— stop assembly is allowed by certified SPEAG personnel only and is part of the annual calibration procedure. Important Note: To prevent damage of the DAE probe connector pins, use great care when installing the probe to the DAE. Carefully connect the probe with the connector notch oriented in the mating position. Avoid any rotational movement of the probe body versus the DAE while turning the locking nut of the connector. The same care shall be used when disconnecting the probe from the DAE. Schmid & Partner Engineering TN_BRO40315AD DAE4.doc 11.12.2009

Calibration Laboratory of NT3 Schweizerischer Kalibrierdienst )( ’/’/ Schmid & Partner mM Service suisse d‘étalonnage v Engineering AG zn Servizio svizzero di taratura \‘\\‘ \ Zeughausstrasse 43, 8004 Zurich, Switzerland / Y Swiss Calibration Service ,//"/uln\“\\\ Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Client Sporton — SZ (Auden) Certificate No: DAE4—1338_Nov16 |CAL|BRAT|0N CERTIFICATE I Object DAE4 — SD 000 DO4 BM — SN: 1338 Calibration procedure(s) QA CAL—O6.v29 Calibration procedure for the data acquisition electronics (DAE) Calibration date: November 22, 2016 This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 + 3)°C and humidity < 70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date (Certificate No.) Scheduled Calibration Keithley Multimeter Type 2001 SN: 0810278 09—Sep—16 (No:19065) Sep—17 Secondary Standards ID # Check Date (in house) Scheduled Check Auto DAE Calibration Unit SE UWS 053 AA 1001 O5—Jan—16 (in house check) In house check: Jan—17 Calibrator Box V2.1 SE UMS 006 AA 1002 O5—Jan—16 (in house check) In house check: Jan—17 Name Function Signature Calibrated by: Adrian Gehring Technician /( % Approved by: Fin Bomholt Deputy Technical Manager | \) ’éz LW Issued: November 22, 2016 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: DAE4—1338_Nov16 Page 1 of 5

Calibration E Laboratory of swMeSs \\—/ > Schweizerischer Kalibrierdienst Schmid & Partner i\hfifi Service suisse d‘étalonnage Engineering AG 2 zy Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland PM, _ w Swiss Calibration Service I/"Il|||\\“\\ Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Glossary DAE data acquisition electronics Connector angle information used in DASY system to align probe sensor X to the robot coordinate system. Methods Applied and Interpretation of Parameters e DC Voltage Measurement: Calibration Factor assessed for use in DASY system by comparison with a calibrated instrument traceable to national standards. The figure given corresponds to the full scale range of the voltmeter in the respective range. e Connector angle: The angle of the connector is assessed measuring the angle mechanically by a tool inserted. Uncertainty is not required. e The following parameters as documented in the Appendix contain technical information as a result from the performance test and require no uncertainty. e DC Voltage Measurement Linearity: Verification of the Linearity at +10% and —10% of the nominal calibration voltage. Influence of offset voltage is included in this measurement. e Common mode sensitivity: Influence of a positive or negative common mode voltage on the differential measurement. e Channel separation: Influence of a voltage on the neighbor channels not subject to an input voltage. e AD Converter Values with inputs shorted: Values on the internal AD converter corresponding to zero input voltage e Input Offset Measurement. Output voltage and statistical results over a large number of zero voltage measurements. e Input Offset Current: Typical value for information; Maximum channel input offset current, not considering the input resistance. e Input resistance: Typical value for information: DAE input resistance at the connector, during internal auto—zeroing and during measurement. e Low Battery Alarm Voltage: Typical value for information. Below this voltage, a battery alarm signal is generated. e Power consumption: Typical value for information. Supply currents in various operating modes. Certificate No: DAE4—1338_Nov16 Page 2 of 5

DC Voltage Measurement A/D —. Converter —Resolution nominal High Range: 1LSB = 6AuV , full range = +100...+300 mV Low Range: 1LSB = 61inV , full range = ~1....... +3mV DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec Calibration Factors KX ¥ Z High Range 403.674 +£0.02% (k=2) 404.250 + 0.02% (k=2) 404.207 + 0.02% (k=2) Low Range 3.97238 + 1.50% (k=2) 3.97905 + 1.50% (k=2) ~8.97471 + 1.50% (k=2) Connector Angle Connector Angle to be used in DASY system 62.0 °+1 ° Certificate No: DAE4—1338_Nov16 Page 3 of 5

Appendix (Additional assessments outside the scope of SCS0108) 1. DC Voltage Linearity High Range Reading (uV) Difference (uV) Error (%) Channel X + Input 199996.77 0.71 0.00 Channel X + Input 20002.26 0.91 0.00 Channel X —input —20000.38 0.70 —0.00 Channel Y¥ + input 199996.98 1.32 0.00 Channel Y¥ + Input 19999.89 —1.32 ~0.01 Channel Y¥ —Input —20003.36 —2.29 0.01 Channel Z + Input 199997.81 1.86 0.00 Channel Z + Input 20001.76 0.52 0.00 Channel Z —Input —20002.73 —1.59 0.01 Low Range Reading (uV) Difference (uV) Error (%) Channel X + Input 2001.72 0.37 0.02 Channel X + Input 201.83 0.23 0.11 Channel X — Input —197.67 0.66 —0.33 Channel Y¥ + Input 2001.35 —0.07 —0.00 Channel Y + Input 200.56 —~1.07 —0.53 Channel Y —Input —199.76 —1.41 0.71 Channel Z + Input 2001.21 —0. 12 —0.01 Channel Z + input 200.89 —0.61 —0.30 Channel Z — Input —199.38 —0.88 0.44 2. Common mode sensitivity DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec Common mode High Range Low Range Input Voltage (mV¥) Average Reading (uV) Average Reading (uV) Channel X 200 7.57 6.75 — 200 —5.52 —6.95 Channel Y 200 —21.81 —21.79 — 200 20.05 19.45 Channel Z 200 ~2.35 —2.47 — 200 0.80 0.82 3. Channel separation DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec Input Voltage (mV) Channel X (uV¥) Channel Y (uV) Channel Z {uV) Channel X 200 — 2.79 —3.02 Channe! Y 200 8.38 = 5.71 Channel Z 200 9.27 5.72 — Certificate No: DAE4—1338_Nov16 Page 4 of 5

4. AD—Converter Values with inputs shorted DASY measurement parameters: Auto Zero Time: 38— sec; Measuring time: 3 sec High Range (LSB) Low Range (LSB) Channel X 16201 15043 Channel Y 16281 15799 Channel 2 16108 15449 5. Input Offset Measurement DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec Input 10MQ Average (V) min. Offset (uV) max. Offset (pV) Std. l():\}l;ation Channel X 1.34 0.13 2.66 0.51 Channel Y¥ —0.17 ~1.21 1.45 0.49 Channel Z ~0.51 —~1.57 0.55 0.45 6. Input Offset Current Nominal Input circuitry offset current on all channels: <25fA 7. Input Resistance (Typical values for information) Zeroing (kOhm) Measuring (MOhm) Channel X 200 200 Channel Y 200 200 Channel Z 200 200 8. Low Battery Alarm Voltage (Typical values for information) Typical values Alarm Level (VDC) Supply (+ Veoc) +7.9 Supply (— Vec) —7.6 98. Power Consumption (Typical values for information) Typical values Switched off (mA) Stand by (mA) Transmitting (mA) Supply (+ VYec) +0.:01 +14 Supply (— Veo) —0.01 —9 Certificate No: DAE4—1338_Nov16 Page 5 of 5

Schmi<j & Partner Engineering AG Zeughausslrasse 43, 8004 Zurich. Swrtzerland Phone +41 44 245 970A, Fax +41 44 Z4b 9779 info@speag.conr, http://www.speag.con.r L2+?

Calibration Laboratory of Schmid & Partner Engineering AG Zeughausstrasse 43, 8004 Zurich, Switzerland Accredited by the Swiss Accreditation Service (SAS) The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates crient Sporton-TW (Auden)

Calibration Laboratory of Schmid & Partner Engineering AG Zeughausstrasse 43, 8004 Zurich, Switzerland

DG Voltage Measurement A"/D - Converter Resolution nominal High Range: lLSB = 6.1pV, = full range _100...+300 mV Low Range: 1 LSB = 61nV , = lull range _1 .......+3mV DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec Calibration Factors Connector Angle

1. DC Voltage Linearity High Range Reading (x¥) |_Ditterence (s¥) Error (%) Channel X + Input 2onoss21 os« aco Channel X + input 20007.04 an oo Channel X —insut 200033« 1e1 oo1 ChannelY + input 2o00s35 on aco Channel Y + input 2ocoass —omn 000 Channel ¥ input —2000693 4s oo Channel 2 + input 20005s« 220 aco Channel 2 + input 2000120 on ‘a00 Channel 2 —Input —20007:71 —1eo oo1 Low Range Reading (i) __|_Diference (1¥) Emor (%) Channel X + input 200035 21 oo Channel X + input 20121 os« ose GhannelX input —rs8a1 ase s2 Ghannel Y _ _ + input 200044 o1 01 Channel Y _ _+ Input z000 o« EB) Ghannel Y ____—input ECmm c0 aco Channel 2 _ _ + input 190073 o7e oo Ghannel 2 _ _ + input 10017 12e Em Channel2 »Input 20005 ose o2e 2. Common mode sensitivity DASY measurement parameters: Auto Zero Time: 3 see; Measuring tme: 3 sec Common mode High Range Low Range Input Voitage (m¥) Average Reading (x¥) Average Reading (x¥) Channel x 200 1881 2008 —200 zes zose Channel Y 2o ase aor —200 —sao ssa Channel 2 Eo sz sgo 200 —zee —1.s0 3. Channel separation DASY measurement parameters: Auto Zero Time: 3 see; Measuring tme: 3 se Input Vottage (mV)__| Channel X (i¥) Channe¥ (1¥)_|_ChannelZ (@¥) GhannelX zo & / asr sse Channel ¥ 2o a2e — a7e Channel 2 2o wer seo — Certfcate No: DAE4—1279_Apri Page 4ot5

1. . ns DASY measurement parameters: Asto Zoro Time: 3 see; Measuring time: 3 se High Range (L5B) Low Range (LSB) Channel x 15007 1s10e Channel v 1sose 11e Channel 2: 15706 1seis 5. Input Offset Measurement DASY measuremant parameters: Auto Zero Time:3 sec; Measutng time: 3 see Inoutown Average (i) min. Offset () max. offset uv) 5« z":;"""‘ Channel x 02e 108 1i ose Ghannel Y o oss n oae Channelz ass 80 on ose 6. Input Offset Current NominalInout crculry offet current on al channels: <25tA 7. Input Resistance (Tysical values fo intormation) Zeroing (kOhm) Measuring (MObm) Ghannel X 200 200 Channel Y 200 200 Channelz 200 200 8. Low Battery Alarm Voltage (Tpical values forinfomation) Typical values Alarm Level (VDC) Supply (+ Vee) 9 Supply (— Vee) 28 9. Power Consumption (Typical values for informaton) i Typical values Switched off (md) Stand by (mA) |__Transmiting (ma) Supply (+ Vee) w01 is «s Supply (—Vee) —oo1 a a Ceriicate No: DAE4—1270_Apri6 Page Sots

Calibration Laboratory of «C . SctvaimnachorKaliviestonst Schmid & Partner sm @ Servicesuiis tinomage Engineering AG reotoninieenthGe ronctstutiens y g. imiemtmmdinie SvienCaltvatonSice Acsrtnd by eSss Acrutain Sevic oas) Aceredtaton No.: SCS 0108 ‘The Sviss Aceredaion Bervice in oeofthemignstore o e tA MottatctAgrement o th ecopnton o eattraton coritents ciem Sporton—8Z(Auden) Guiteaiso: EX3—3011_Sop16 |CALIBRATION CERTIFICATE otea exiove—sysort Cattaten peceduets OA CAL—010, OA CAL—144, OA CAL—23v6, OA CAL—25ve Gallbration procedurefordosimetric E—feld probes Catvaton ue September 29, 2016 Ti calbaton cerfete docmeis h ce ts atoraiandais uich man t pyven uns o manmremonts 50 The neasrmnent ant h uncaiier w conidece ratasyaegen n t otoning pageand on put ofi cotcate Abcatirtons hae beon cecucnd n h clon artoy fatiy envtonontlrorare 2. )C ons Iavdty s 70% CattaionEniement ud (MAT etca o caitnton) Prma Suraus o CaiDas(Conieati) Schatde Catrsion Poom n NP Entuo ceaoci8 oi 2izazzmmnzzne ectr Pow sume 180:201 sn rovam cesco arrazmn heear Pome se w291 sn oses aois tie 217zen Aecir FRetwance 20 on Aterante sn serr ) socss ne arrazam) hecwr Relvence Pobe Esaove sw 3013 arorets n Exsaon pecte tect6 miee sn wo zowts ie piteasnpecto Dect# Senday Grdars C Gex se intame sueited Gack romnam csump s commowe 0620018 inhome test Si intowe cesJnt Pose smo Eevizn s wvavansonr 0618 inrome ces hn18| inteae cescJncth Pome use Eatian sn moonionto 018 inhomecect hnt intoie cesc uit RF qovonie ie sou sn ussseuource 0t (n tame ces unt0) intowe ces Jnt Netvrk Aeaten h sriie ow ussraioees 180001 tnhowe ds 0 19 nonediest Ois Nime Fnciss Catemetty fetue infomyresims: g?z@ Aspromty rotapdose Tocrcaloroge /6?4 Iimunt Ociatera, 2016 This caltaen cmntete hint ho orodvend scet n nthtit arorealf h tm Ceriicate No: —3011_Sopto Page t ot 11

Calibration Laboratory of Schmid & Partner «C «C iA setwatsntsche Kainrtonst $ fnmmmetiemey Engineering AG ’% § senino mtc itamtom Zughestiase 45 1004 Rarch, Sutzerand 44”'”‘ m Butss Caltraton Senice Accndin b t Sus Acrstatcn Sevic (SA5) Acermitaton: SCS 0108 ‘he Svis Aceredtation Sarvcn s one ofthesignntaies ioh EA thllaerat Agremantfo th ocognton o catbraton coitents Glossary: Tst tissue simulatig fquld NoRMxyz sensivit in roe space Com sensitvit in TSL / NORMcyz BoP dlode compression point or erest factor (Viuty.cycl) of the RF signal As.c.0 moxiiion dependent Invarization paramotors Polarizaion o «»rotaion araund probe anis Polarzation 8 3 rotaion around an axis thatis in the plane normalto probe axis (at measurement center) Le, 8 = 0 is nomal to probe axis Connector Angle information used in DASY system to algn probe sensor X o the robot coortiate system Callbration is Performed According to the Following Standards: a). IEEE Sid 1528—2013, IEEE Recommended Practio fr Determining the Poak Spatal—Averaged Specife Absorpton Rate (SAR)in the Human Head from Wreless Cormmunications Devices: Monsuroment Techriques®. June 2013 ): 12C 62208—1, "Procedore to maasurethe Speciic Absorption Rate (SAR)fr hand.held devices used in close proimityto the ear (requency range of 300 Mitz to 3 Gitz, Febrwary 2006 ): 120 62200—2,‘Procedure to determine the Speciic Absorplon Rale (SAR)for wireless communication devices used in elose prowmty tothe human body (equency range of 30 iz t 6 GHiz‘, March 2010 4). KDB 865604, °SAR Mansuremant Requroments for 100 Mite o 6 Gitz" Methods Applied and interpretation of Parameters: NOR3 Asswosed fo E:ild plarzation 0 (!= 900 Ntz in TEM—col; 1 1800 NHz:R22 waveguide}, NORMixy.z are only intermedate values,to, mmmmusarmmy,zmw-fl-amE‘feld uncerainty inside TSL (seo below Gonv£). * NORb(Mcycz = NORMcy.z * Iequeney.response (see Frequency Response Chart. ThisInoarzatonis implemanted in DASY4 software versionslate than 4.2. The uncertaintyof thafreaueney rosponse i ncluded in the stated uncertaity of Conv. + DGPxy.z: DCP are numericalnearzaton paramelers assessed based on the data of power seep with CW signal (ro unceriainlyrequired). DCP does not depand on frequency nor media + PAR: PMR i the Peak to Average Rao thatis not calbrated but determined based on t signal cturactenitcs +. Arjie: Beyie: Ooa Drgce: VRuyiz: A, 8. 6. 0 are numericalInearizaon parametars assessed based on the data of power sureap for anecifc modilaton signa. The pararmetars do not dpend on froquency nor madi. VR is the maximum calation range expressud in RMS vailage across the code. + Conv£ and Boundary Efict Paramaters: Assesed fatphantem using E—fald (or Temporture Transter Standard fort © 800 MHz) and inside waveguide using anabyicalfld dstbutions based on power measurements or 1 > 800 MFiz. The same setups are used for assesmant ofthe parameters applied fr boundary compensation(alpha, depth)of which typicl uncertainty values aregven. Those paraimetersare used in DASYA suttware 1o mprove probe accuracy clase to the boundary, The sensllvly in TSL corresponds to NORMcy.z * ConvE whereby the uncertainy cortusponds o that gvan or ConyE. A frequency depandent Corv is used in DASY version 4.4 and higher which aows oxtending the valdity rom + 50 MHzt 2100 Wtz * Sphericalisotrapy (30 deviation from isotopy} in a fald of ow gradientsrealzed using a fat phanten exposed by a paich antemna. + Sensor Offet The sensor offse comesponds to the ofietof virual mensurement centerfrom the probe tp (on probe asi). No tolerance requred + ComectorAngle: The angle is assessed using the nformalion gained by deternining the NOR(no uncerainy requred) Certtcate No: Ex3—3011.Sonté Page 20t 11

EX3DV4 — SN:3911 September 29, 2016 Probe SN:3911 Manufactured: September 4, 2012 Calibrated: September 29, 2016 Calibrated for DASY/EASY Systems {Note: non—compatible with DASY2 system!) Certificate No: EX3—3911_Sep16 Page 3 of 11

EX3DV4— SN:3911 September 29, 2016 DASY/EASY — Parameters of Probe: EX3DV4 — SN:3911 Basic Calibration Parameters Sensor X Sensor Y Sensor Z Unc (k=2) Norm (uV/(V/im)*)* 0.30 0.33 0.47 +10.1 % DCP (myv}* 101.9 102.3 100.2 Modulation Calibration Parameters UID Communication System Name A B C D VR Unc® dB dBvuV dB mV (k=2) 0 CW xX 0.0 0.0 1.0 0.00 138.8 £3.5 % Y 0.0 0.0 1.0 138.9 Z 0.0 0.0 1.0 138.4 The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. * The uncertainties of Norm X,Y,Z do not affect the E*—field uncertainty inside TSL (see Pages 5 and 6). ® Numerical linearization parameter: uncertainty not required. & Uncertainty is determined using the max. deviation from linear response applying rectangular distribution and is expressed for the square of the field value. Certificate No: EX3—3911_Sep16 Page 4 of 11

EX3DV4— SN:3911 September 29, 2016 DASY/EASY — Parameters of Probe: EX3DV4 SN:3911 Calibration Parameter Determined in Head Tissue Simulating Media Relative Conductivity Depth ° Unc f(MHz)° Permittivity® (S/im)" ConvFX ConvFY ConvFZ Aipha® (mm) (k=2) 750 41.9 0.89 10.99 10.99 10.99 0.57 0.81 *# 12.0 % 835 41.5 0.90 10.54 10.54 10.54 0.26 1.26 # 12.0 % 900 41.5 0.97 10.05 10.05 10.05 0.38 0.93 £#12.0 % 1750 40.1 1.37 8.88 8.88 8.88 0.31 0.93 + 12.0 % 1900 40.0 1.40 8.50 8.50 8.50 0.40 0.80 #12.0 % 2000 40.0 1.40 8.48 8.48 8.48 0.35 0.85 #* 12.0 % 2300 39.5 1.67 7.93 7.93 7.93 0.36 0.80 + 12.0 % 2450 39.2 1.80 7.43 7.A3 7.43 0.29 0.98 + 12.0 % 2600 39.0 1.96 7.39 7.39 7.39 0.45 0.80 + 12.0 % 5250 35.9 4.71 5.25 5.25 5.25 0.40 1.80 £# 13.1 % 5600 35.5 5.07 4.49 4.49 4.49 0.50 1.80 + 13.1 % 5750 35.4 5.22 4.75 4.75 4.75 0.50 1.80 *# 13.1 % © Frequency validity above 300 MHz of £ 100 MHz only applies for DASY v4.4 and higher (see Page 2), else it is restricted to + 50 MHz. The uncertainty is the RSS of the ConvF uncertainty at calibration frequency and the uncertainty for the indicated frequency band. Frequency validity below 300 MHz is * 10, 25, 40, 50 and 70 MHz for ConvF assessments at 30, 64, 128, 150 and 220 MHz respectively. Above 5 GHz frequency validity can be extended to £ 110 MHz. " At frequencies below 3 GHz, the validity of tissue parameters (s and 0) can be relaxed to + 10% if liquid compensation formula is applied to measured SAR values. At frequencies above 3 GHz, the validity of tissue parameters (s and 0) is restricted to + 5%. The uncertainty is the RSS of the ConvF uncertainty for indicated target tissue parameters. © Alpha/Depth are determined during calibration. SPEAG warrants that the remaining deviation due to the boundary effect after compensation is always less than + 1% for frequencies below 3 GHz and below + 2% for frequencies between 3—6 GHz at any distance larger than half the probe tip diameter from the boundary. Certificate No: EX3—3911_Sep16 Page 5 of 11

EX3DV4— SN:3911 September 29, 2016 DASY/EASY — Parameters of Probe: EX3DV4 — SN:3911 Calibration Parameter Determined in Body Tissue Simulating Media Relative Conductivity Depth ° Unc f(MHz)° Permittivity"® (Sim}" ConvF X ConvF Y¥ ConvFZ Alpha® (mm) (k=2) 750 55.5 0.96 10.43 10.43 10.43 0.42 0.80 + 12.0 % 835 55.2 0.97 10.19 10.19 10.19 0.20 1.33 + 12.0 % 1750 53.4 1.49 8.46 8.46 8.46 0.42 0.80 £# 12.0 % 1900 53.3 1.52 8.17 8.17 8.17 0.35 0.97 + 12.0 % 2300 52.9 1.81 7.93 7.93 7.93 0.33 0.98 #12.0 % 2450 52.7 1.95 7.66 7.66 7.66 0.43 0.80 + 12.0 % 2600 52.5 216 7.38 7.38 7.38 0.33 0.80 +12.0 % 5250 48.9 5.36 4.62 4.62 4.62 0.50 1.90 *13.1 % 5600 48.5 5.77 3.78 3.78 3.78 0.60 1.90 £#13.1 % 5750 48.3 5.94 3.95 3.95 3.95 0.60 1.90 £13.1 % © Frequency validity above 300 MHz of + 100 MHz only applies for DASY v4.4 and higher (see Page 2), else it is restricted to + 50 MHz. The uncertainty is the RSS of the ConvF uncertainty at calibration frequency and the uncertainty for the indicated frequency band. Frequency validity below 300 MHz is + 10, 25, 40, 50 and 70 MHz for ConvF assessments at 30, 64, 128, 150 and 220 MHz respectively. Above 5 GHz frequency validity can be extended to £ 110 MHz. " At frequencies below 3 GHz, the validity of tissue parameters (e and 0) can be relaxed to + 10% if liquid compensation formula is applied to measured SAR values. At frequencies above 3 GHz, the validity of tissue parameters (s and 0) is restricted to + 5%. The uncertainty is the RSS of the ConvF uncertainty for indicated target tissue parameters. 8 Alpha/Depth are determined during calibration. SPEAG warrants that the remaining deviation due to the boundary effect after compensation is always less than + 1% for frequencies below 3 GHz and below + 2% for frequencies between 3—6 GHz at any distance larger than half the probe tip diameter from the boundary. Certificate No: EX3—3911_Sep16 Page 6 of 11

exsov—swan Sertonber29, 2018 Frequency Response of E—Field (TEM—Coll:if110 EXX, Waveguide: R22) $ Frequency response (normatzed) & $ $ £..4 M s s Uncertainty of Frequency Response of E—feld: 2 6.3% (KeZ) Certtcats Ne E33011Sents Page? of 11

waove— swaons Septentor29, 2010 Receiving Pattern (¢), 9 = 0° £°600 MHz,TEM 121800 MHz,R22 Erer1 Uncertainty of Axial Isotropy Assossment: £0.5% (ke2) Certfcate Ne ©3—3011_Sopt6 Page Bot 11

woove—suson Septemtor28, 2016 Dynamic Range f(SARncaq) (TEM cell , f..,= 1900 MHz) Uncertainty of Lincarity Assessment: £0.0% (kx2) Certfcats No: ©G—3011_Sept6 Pagn t t1

Bcovi—suson sertenter2s, 2016 Conversion Factor Assessment 1= sas mzWweus mo (1_come) 1= 1900 izWGLS R2Z 1.comF) wX $ i. 5‘n tel i _ | uw w t ce *4 I kc 199 Deviation from Isotropy in Liquid Error (6, 9), £= 900 MHz: —0 «es ss o« —o2 oo or o4 os o8 10 Uncertainty of Sphorica Isotropy Assessment+26% (te2) Certtems No: Exsa911.Sent6 Page tost11

EX3DV4— SN:3911 September 29, 2016 DASY/EASY — Parameters of Probe: EX3DV4 — SN:3911 Other Probe Parameters Sensor Arrangement Triangular Connector Angle (°) 80 Mechanical Surface Detection Mode enabled Optical Surface Detection Mode disabled Probe Overall Length 337 mm Probe Body Diameter 10 mm Tip Length 9 mm Tip Diameter 2.5 mm Probe Tip to Sensor X Calibration Point 1 mm Probe Tip to Sensor Y Calibration Point 1 mm Probe Tip to Sensor Z Calibration Point 1 mm Recommended Measurement Distance from Surface 1.4 mm Certificate No: EX3—3911_Sep16 Page 11 of 11

r Calibration Laboratory of g. Semnizerctr taitientonst Schmid & Partner § sevvce mteenitiilomonge Engineering AG § sentzo micer o es iaghavestmase 131004 2arch,Suiteriand Suiee Cattrstonterice Acemdtd by te Swan Acrutaton Servcn(A8) Aecdtaton : SCS 0108 The SwiasAccradtaton Bervic is on oth signtorsto tsA ttintrt Agrremont fortherecognten of cabraton conitcaues ciew SportomK8(Auden) cenitcas EX3—3054.Nov16 |CALIBRATION CERTIFICATE ovea exsove shigose Cattraton poceduts) OACAL—O19,OA CAL—T4x4, OACAL—23v6, OA CaL—23v6 ‘Callbration procedure fordosimetic E—flld probes Caitraton dn November 28 2016 is caltrate critcate dccsments the racenbay o natonat tardaisuc eatc t pysca unts t memurements(3) Th namrenent and e srcnianien w contderce robsbiny e gvan on t ftowngpage an re pr o h crtcan Adcatiaters hav on condetn i th ow on lt eniorment anperaire 2 227C an hanity«70% CalratonEaeimntvan TE erteltocaraton) Priman Standarts o GitDate (Gonteai o) Sctmaded Catteaton rov nawe n Entun 018 t 27w0z weer Pove sese ts#251 sn wn oeterts m 2irz00 heerr Fome seme 19.251 snons 0ct 2rrazam tecr Hetvence 20 08 Atovate on sser goo oA1 t 217 oo Aoctr Retwerce Pobe Essove sn aots srbrers pis EssaotsSecth Decie mee siow Zpre1s in Dibito Dects) Deeis Smomay Sordugs m Gexbae nrong soatied ies Pomenow tattt0 sn coumen h018 n rowmechook is_ Intomececk anB Foversemer E2k si mvaremonr Apcil n home ced Jn 10— inomectect unis Poverseme Eotizn snoomson otAnc18 inhomectec hn19— ntomeciec: hn it qonpaowes s ussotzuorni0 240 intowe dad in—| Intomecte ani8 netvorsAeaie ve arsse s ussrasous 180001 in owctea 0s—16) intowsecteac Oc17 Rure Fade Span Caitaie by LotiOrnec LatentoyTachicon ‘ '%, Anpontty wilPolove ‘Toaiialbiamigee ®é&. hnNoventer 22016 Th cattraten cutteae stt nc h merrducnd merst in t uthut w aporon o t iatortoy Corttcate No: Ex3—305¢ Novio Page t t 11

r Callbration Laboratory of .: Seeicnschor Katierdinst Schmid & Partner & Server sisse tiomage Engineering AG & Seride ies amre irvghausstnase 43. 1004 2ich, Sntentand SuissCattraton Senice Acendta by t un AcrudatenServen(A8) Acedtatontis: SCS 0108 The Swiss Accradtaton Sarice i on oft nigntorestohe A MitimertAgreament fore recognton of cabratonconicates Glossary: Tst tesue simulatng lould NoRMxya sensitviy in ree space Comt sensibvty in TSL / NORMyz ocp iode compression point or erest factor(tiduty_cle)ofthe RF signal A8.c.0 moxiiation dependantncarzation parameters Polarzation o « otation around probe is Polariaton 0 8 rotation around an anis that is n the plane normal t probe ax‘s(at measuremont conter, t, 0 =0 is normalto probe axis Comnector Angle information used in DASY systom to algn probe sensor X to the robot coortinate system Calibration is Performed According to the Following Standards: a).IEEE Sid 15282013, 1EEE Recommended Practicefor Deternining the Poak Spatla—Averaged Specite Absorption Rate (GARin the Human Head from Wireless Communications Devices: Meosurement Technques®,Jine 2013 6). 120 62200—1, *Procedure to measure the Speciic Absorption Rate (SAR) forhand—held devices used n cose prowimitt the ea(Requency range of 300 Mz to 3 GHzF, February 2005 e). 120 62200—2, ‘Procedureto determine the Specifc Absorplon Rate (GAR) or wreless communication devices used in close proximit to the human boy (requency range o 30 MHe to 6 Giic), March 2010 4) KDB 658. SAR Measuremont Requrementsfor 100 Mz t 6 GHtz" Mothodl Applied and Interpretation of Parameters: NORMrqca: Assessed forE—fld polaizaion & =0 t 900 MEtz in TEM—cel;1> 1900 Mite:R22 wavequide}. NORM3.z are onl intermediate valuesL. the uncertaintes of NORM3.z does not affec the E—feld unceraint nside TS (see below Con?) * NORM(Mry.z = NORkxy:z *requency. response (see Frequency Response Chart) This ncarization is implamented in DASY4 sotware versionslato than 4.2.The uncertaity f the requency response is included in the stated uncertanty of GomvF: + 0GPxy.2: DGP are numerical inearizaion parameters assessed based on the data of power sweep with CW signal(no uncertaintyrequired). DCP does not depend on frequency nor media. + PAFR: PAR is the Reak to Average Ratlo thais not calbrated but determined based on the signal churacterstcn +. AujieBycz Cigcz: Diy.z: VRiey.z: A, . G, D are numericl inearization parameters assossed based on the data of power swaes for speciic modulton signal, The parameters do not depend on frequency nor media. VR s the maximum calbration range expressed in RMS vatage across the dode * Gorveand Boundary Elfect Paramaters: Assessed in flat phantom using E—ld (or Temporature Transter Standard fof 800 MiHz) and inside waveguide using analylalfld distibutions based on power measuremantsfo > 800 MHz. The same setups are used for assessment of the parameters appled for boundary compensation (alpha, depth)of which typical uncertaintyvalues are given, These parameters aro used in DASY4 sottware toimprove probe accuracy close to the boundary. The senstily in TSL coresponds to NORMy.z * Cany whereby the uncertainty corresponds t that aven for ConyF, Afeuency dependent Conis used in DASY version 4.4 and higher which alows oxtending th valdty om 2 50 MHe to 2 100 lb * Sphriea!isotray (3D deviaton rom isotrogy) in a l of ow graclents realized usinga t phantom expased by a patch antenna. * Sensor Offet:The sensor oifset coresponds tothe ffsatof virval measurement centerfrom the probe to on probe anis)No tolerance required * Comnetor Angl: The angle s assessed using the information gained by deternining the NORA (ro uncertainty requred) Gortieat No: Ex1084 Nort6 Page 20¢ 11

wxaove — snsost Novembor 2n, 2018 Probe EX3DV4 SN:3954 Manufactured: August 6, 2013 Repaired: November 21, 2016 Calibrated: November 28, 2016 Calibrated for DASY/EASY Systems (Note: non—compattle with DASYz system!) Certfcats No: XG—3084 No Page ott1

waove— swsoss Novemor 282016 DASY/EASY — Parameters of Probe: EX3DV4 — SN:3954 Basic Calibration Parameters SensorX Semsory Sensorz Wns tm Nom @Wivim?)" ost oas ose riork 0CP (my) w mork sro Modulation Calibration Parameters uo CommunicationSystem Name x a c a w we" . «n anviv «n mv dem 8 se x|_os _|_oo 1o_| o0 meo ss3% v|_os oo 10 Tas zoo so i0 mea The reported uncertainty of measurement is stated as the standard uncertainty of measurement multipled by the coverage factor k=2, which for a normal distrbution corresponds to a coverage probabilty of approximately 95%. { The emabtos o Norm XY 2 on atet h E‘dad unc nide T9L o Pagen ad 1 ©Phrmareat evancaton paanater incetanty ot nuend * Unctant n dtenined ng tm max. cdvatontm Innw esporse asoyog recngi durtuton ant n oresa o i scare o ho fottave Cortieats No: EX3—305¢.Novtd Page o 11

exsove— smause Novermbor20, 2016 DASY/EASY — Parameters of Probe: EX3DV4 — SN:3954 Callbration Parameter Determined in Head Tissue Simulating Media romy P-mut:'hy‘ °°2“n"nf‘fi"" ComeX comey |_Comtz Aha n(.nwn" (‘ut'z:) 1so a10 ose 1oss toss se osr os2 +120% s3s 415 080 1052 1082 1052 o6 142 +120% s0o 415 oar 1035 1035 1035 036 oss 2120% 1750 «0 137 ase 858 a58 ost ost +120% 1900 400 140 s3 832 a32 oa7 127 2120% 2000 «0 140 823 823 s23 022 1i 2120 % 2300 305 167 788 T88 Tss o21 116 1120% 24so soe 180 zaa ras ras oz omt r120% 2600 200 198 mm ze ra on is se 3500 3r0 201 710 710 710 030 120 +181 % seso aso an sos sos sos oss so arsi% | seoo sss sor «70 are azo oso 180 sis1% stso asa s2e aso aso iss os im asi% ©Irequeey vakayahor 0 c t 100 Mb on apute o DA vet and grer sePage 2)ols s etici t# 0t The vecertant n h S t heCm unceiany t calealontecuecyand ho uncntant to in nicate haqurcy band Freavercyaity befow 300 ht n a 10254090 and 7 e o Cordansesnent a 3. 4,120, 10and 220 it respeciniy ow 8 lt repuercy d can b edandeits s 110 itc ‘Athocuencs tlow3Gith valdy fue parelos co) cab alne o 10% 1 ui conponatan m s ovote o rnoasnd SA etam. At unc atove 3 GMe h iniay oue paranetrs(cano in esnt o 2. Thurcetany te RSS of theGord urcetant to intcin getoowpwnates *Aorwoedth dtemiead ving caaton 5P€AG warans iate remaring devaton danto hboondry lc ate compersalon s aayton n 11 o Heauercietw 3 C ad blow 21 orbaguercn uoo 20 GHeatany marc age hn hie pate t danaeton ho ocnday Centicas No: Ex—s054 Norte Page S1

exsove~ snaose Novembor 20, 2016 DASY/EASY — Parameters of Probe: EX3DV4 — SN:3954 Calibration Parameter Determined in Body Tissue Simulating Media rmn* |_pentnly‘ [im| comex comey |_comez mpna® "m)_|_ 9 150 sss ase tose tose tos: on os s120% ass see osr 1032 tos2 tos om im s120% 1750 534 149 ase ase ase PE oso +120% 1900 s3 182 ao1 a01 so1 040 os0 2120% 230 s2o 181 teo zso rso ois om «t20% 2450 sar 195 zss zss 1ss oar oso «120% 2600 sas 216 zos zos tos oo osi »120% sso sis aan ers ers ers o 120 a111% seso «s0 s3e aso aso |aso ous 180 e1s1% se00 «85 s77 302 a0e 307 oso 190 a131% stso «s3 so «0s sos aos oss 18 s121% 5 equency uky aheve 200 t 100 t on aptes o DASY t and Nghr se Page 21 i t i reivctoto + 0M The «ncetant n e ASG o he Com? ncerany acaliatonbecuncy andtheunconnty t t indcatat hocurcyband Frperoy altty ow 200 ht a 16254050 and 7 te o C annesumenis t 20. 6,120, 10 ant 20 Mte eseaivty Aboe 8 it rapurcy ywdycan t denan i 110ht * t hecuenc bolaw3 6t ne vahyof ie arne ( o ) con t ow t 109 i compernaton tm in apste t «nemrnSA vaum. 2t becurcim acov C in ind o taou arel i n o) enc t 1. Th ncwiany t SS of toeGooi nontanty forindcin ge t ocanuts * AprDoothar detenined suing citaten SPEAG vrartsat h renonngdevaton in t h bounda ol ate cepruaton is atraye leaitea19 t Reuerce i 3 Gie and biow a 2s o hnguencen etron 20 GHeat onitarc y Ian hatito mobe to mite tom bocnday Certfcate No EX—054Norte Page Got 11

exaove~suasst Novemtor28, 2016 Frequency Response of E—Field (TEM—Collif110 EXX, Waveguide: R22) &2 8 P && { 1 as foccc oo oo uol o) uc c aoiefacaer— 6 sco 1000 1sho ano 2so aio Tiz S Uncertainty of Frequency Response of Eld: 2 6.3% (es2) Cerifcate No: ©G—2054 Novte Page 7 of 11

exaove~ snaose November 20, 2018 Receiving Pattern (¢), 3 = 0° f°600 MHz,TEM (=1800 MHz,R22 Enc lod . B * Uncertainty of Axial Isotropy Ausossmont: + 0.5% (ke2) Cerifcate No: Exs—395Novt6 Pageot 11

paov— suaoss Novnbor28. 208 Dynamic Range f(SARncaq) (TEM coll , fo,.r= 1900 MHz) U: 1 oo smln‘rgwml ® noteobfihsst eontilacs Uncertainty of Linearity Assossmont: £0.6% (ke2) Corticat No: 054Novt6 Page tot 11

exciove— suaose Noveribor20, 2016 Conversion Factor Assessment 1 = aas hMzWGLS R (.come) 1= 1900 MitcWGLS Rz® _connt) uP i a Deviation from Isotropy in Liquid Error (6, 8), £=900 MHz «0 sos os o« mz oo o2 o4« os o8 10 Uncertainty of Spherica Isotropy Assossmonts # 2.6% (ke2) Corticate No: Ex3.205¢.ovt6 Page 10 of 11

wxaove— saose Novermtor 2n,2016 DASY/EASY — Parameters of Probe: EX3DV4 — SN:3954 Other Probe Parameters Sensor Arangement nector Angje () Mechanica Surface Detecton Mode OplcalSurlace Detection Mode Probe OveraLengh Probe Body Diamoter To Lngh To Damefer Frobe Tisto Sensor X Galbraton Poin Probe Tisto Sensor V Gallbration Point Probe Tipto Sensor Z Calbraton Point Recommended Measurement Distance from Surface 14 mm Centcato No: 084Novld Page 11 of 11


Document Created: 2017-12-29 19:49:44
Document Modified: 2017-12-29 19:49:44
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC