JBP Report

FCC ID: PPD-QCA9008-TBD1

Test Report

Download: PDF
FCCID_2714690

FCC Certification Test Report Report No.: FC150226E05 Test Model: QCA9008-TBD1 Received Date: Feb. 26, 2015 Test Date: July 02, 2015 Issued Date: July 15, 2015 Applicant: Qualcomm Atheros, Inc. Address: 1700 Technology Drive, San Jose, CA 95110 Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory Lab Address: No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan R.O.C. Test Location (1): No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan R.O.C. Test Location (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. The report must not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: FC150226E05 Page No. 1 / 24 Report Format Version: 6.1.0

Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ......................................................................................................................... 4 2 Summary of Test Results......................................................................................................................... 5 2.1 Measurement Uncertainty ................................................................................................................... 5 2.2 Modification Record ............................................................................................................................ 5 3 General Information ................................................................................................................................. 6 3.1 Features of EUT .................................................................................................................................. 6 3.2 General Description of EUT ................................................................................................................ 6 3.3 Description of Antenna ........................................................................................................................ 7 3.4 Operating Modes of EUT and Determination of Worst Case Operating Mode ................................... 7 3.5 Test Program Used and Operation Descriptions ................................................................................. 7 3.6 Primary Clock Frequencies of Internal Source ................................................................................... 7 3.7 Miscellaneous ...................................................................................................................................... 8 4 Configuration and Connections with EUT ............................................................................................. 9 4.1 Connection Diagram of EUT and Peripheral Devices ......................................................................... 9 4.2 Configuration of Peripheral Devices and Cable Connections ........................................................... 10 5 Conducted Emissions at Mains Ports ................................................................................................... 11 5.1 Limits .................................................................................................................................................. 11 5.2 Test Instruments ................................................................................................................................. 11 5.3 Test Arrangement .............................................................................................................................. 12 5.4 Supplementary Information ............................................................................................................... 12 5.5 Test Results ....................................................................................................................................... 13 6 Radiated Emissions up to 1 GHz .......................................................................................................... 15 6.1 Limits ................................................................................................................................................. 15 6.2 Test Instruments ................................................................................................................................ 15 6.3 Test Arrangement .............................................................................................................................. 16 6.4 Supplementary Information ............................................................................................................... 16 6.5 Test Results ....................................................................................................................................... 17 7 Radiated Emissions above 1 GHz......................................................................................................... 19 7.1 Limits ................................................................................................................................................. 19 7.2 Test Instruments ................................................................................................................................ 20 7.3 Test Arrangement .............................................................................................................................. 21 7.4 Supplementary Information ............................................................................................................... 21 7.5 Test Results ....................................................................................................................................... 22 Appendix – Information on the Testing Laboratories ................................................................................ 24 Report No.: FC150226E05 Page No. 2 / 24 Report Format Version: 6.1.0

Release Control Record Issue No. Description Date Issued FC150226E05 Original release. July 15, 2015 Report No.: FC150226E05 Page No. 3 / 24 Report Format Version: 6.1.0


2 Summary of Test Results 47 CFR FCC Part 15, Subpart B / ICES-003:2012 Issue 5, Class B ANSI C63.4:2009 FCC ICES-003 Test Item Result/Remarks Verdict Clause Clause AC Power Line Conducted Minimum passing Class B margin 15.107 6.1 Pass Emissions is -7.48 dB at 0.21250 MHz Radiated Emissions up to 1 Minimum passing Class B margin 6.2.1 Pass GHz is -4.05 dB at 73.50 MHz 15.109 Radiated Emissions above 1 Minimum passing Class B margin 6.2.2 Pass GHz is -19.92 dB at 5757.75 MHz Note: There is no deviation to the applied test methods and requirements covered by the scope of this report. 2.1 Measurement Uncertainty Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT: The listed uncertainties are the worst case uncertainty for the entire range of measurement. Please note that the uncertainty values are provided for informational purposes only and are not used in determining the PASS/FAIL results. Expended Uncertainty Measurement Frequency (k=2) (±) Conducted Emissions at mains ports 150kHz ~ 30MHz 2.86 dB Radiated Emissions up to 1 GHz 30MHz ~ 1GHz 3.99 dB 1GHz ~ 6GHz 3.65 dB Radiated Emissions above 1 GHz 6GHz ~ 18GHz 3.50 dB 18GHz ~ 40GHz 4.11 dB 2.2 Modification Record There were no modifications required for compliance. Report No.: FC150226E05 Page No. 5 / 24 Report Format Version: 6.1.0

3 General Information 3.1 Features of EUT The tests reported herein were performed according to the method specified by Qualcomm Atheros, Inc., for detailed feature description, please refer to the manufacturer's specifications or user's manual. 3.2 General Description of EUT Product 802.11abgn/ac/ad+BT module Brand Qualcomm Atheros Test Model QCA9008-TBD1 Sample Status ENGINEERING SAMPLE Operating Software NA Power Supply Rating 3.3Vdc from host equipment Accessory Device NA Data Cable Supplied NA Note: 1. There are Bluetooth technology and WLAN technology used for the EUT. 2. The EUT incorporates a 2T2R function. 2.4GHz Band MODULATION MODE DATA RATE (MCS) TX & RX CONFIGURATION 802.11b 1 ~ 11Mbps 2TX 2RX 802.11g 6 ~ 54Mbps 2TX 2RX MCS 0~7 2TX 2RX 802.11n (HT20) MCS 8~15 2TX 2RX MCS 0~7 2TX 2RX 802.11n (HT40) MCS 8~15 2TX 2RX MCS 0~8, Nss=1 2TX 2RX VHT20 MCS 0~8, Nss=2 2TX 2RX MCS 0~9, Nss=1 2TX 2RX VHT40 MCS 0~9, Nss=2 2TX 2RX 5GHz Band MODULATION MODE DATA RATE (MCS) TX & RX CONFIGURATION 802.11a 6 ~ 54Mbps 2TX 2RX MCS 0~7 2TX 2RX 802.11n (HT20) MCS 8~15 2TX 2RX MCS 0~7 2TX 2RX 802.11n (HT40) MCS 8~15 2TX 2RX MCS 0~8, Nss=1 2TX 2RX 802.11ac (VHT20) MCS 0~8, Nss=2 2TX 2RX MCS 0~9, Nss=1 2TX 2RX 802.11ac (VHT40) MCS 0~9, Nss=2 2TX 2RX MCS 0~9, Nss=1 2TX 2RX 802.11ac (VHT80) MCS 0~9, Nss=2 2TX 2RX 3. WLAN/BT coexistence mode: ◆ 2x2 WLAN + BT:  5GHz 802.11a/an (or 11ac) transmit concurrent with BT.  2.4GHz: timely shared coexistence. Report No.: FC150226E05 Page No. 6 / 24 Report Format Version: 6.1.0

3.3 Description of Antenna The antenna gain was declared by client; please refer to the following table: 2.4GHz Gain 2.4GHz Cable Transmitter Ant. with 5GHz Gain with Cable 5G Cable Loss Connector Brand Model Length Circuit Type cable loss cable loss (dBi) Loss (dBi) Type (mm) (dBi) (dBi) Band 1&2: 2.56 Band 1&2: 1.70 Chain (0) WNC 81-EBJ15.005 PIFA 3.00 Band 3: 4.76 1.15 Band 3: 1.74 IPEX 300 Band 4: 4.76 Band 4: 1.79 Band 1&2: 3.08 Band 1&2: 1.70 Chain (1) WNC 81-EBJ15.005 PIFA 3.62 Band 3: 3.31 1.15 Band 3: 1.74 IPEX 300 Band 4: 2.42 Band 4: 1.79 Note: 1. Above antenna gains of antenna are Total (H+V). 2. All of antenna can be application for WLAN and Bluetooth. For Testing, we select the highest gain on each frequency band for calculation and testing The detail information as below: 2.4GHz Gain 2.4GHz Cable Transmitter Ant. with 5GHz Gain with Cable 5G Cable Loss Connector Brand Model Length Circuit Type cable loss cable loss (dBi) Loss (dBi) Type (mm) (dBi) (dBi) Band 1&2: 3.08 Band 1&2: 1.70 Chain WNC 81-EBJ15.005 PIFA 3.62 Band 3: 4.76 1.15 Band 3: 1.74 IPEX 300 (0)+(1) Band 4: 4.76 Band 4: 1.79 3.4 Operating Modes of EUT and Determination of Worst Case Operating Mode EUT has been pre-tested under following test modes, and test mode 2 was the worst case for final test. Mode Test Condition 1 WLAN (5GHz) + BT mode 2 WLAN (2.4GHz) + BT mode Test mode is presented in the report as below. Test Condition Mode Description 1 WLAN (2.4GHz) + BT mode 3.5 Test Program Used and Operation Descriptions 1. Turn on the power of all equipment. 2. Support unit A (NOTEBOOK COMPUTER) runs test program “Ping.exe” to link with support unit F (WiFi AP) via EUT by Wireless. 3. Support unit A (NOTEBOOK COMPUTER) links to support unit G (NOTEBOOK COMPUTER) via EUT by BT. 3.6 Primary Clock Frequencies of Internal Source The EUT is a WLAN and BT technology device, provided by Qualcomm Atheros, Inc., for detailed internal source, please refer to the manufacturer's specifications. Report No.: FC150226E05 Page No. 7 / 24 Report Format Version: 6.1.0

3.7 Miscellaneous Labelling Requirements for Part 15 Devices:  Verification The specific labelling requirements for a device subject to the Verification procedure are contained in Section 15.19(a). These labelling requirements are: If the device is subject only to Verification, include a label bearing a unique identifier (Section 2.954) and one of three compliance statements specified in Section 15.19(a). If the labeling area for the device is so small, and/or it is not practical to place the compliance statement on the device, then the statement can be placed in the user manual or product packaging (Section 15.19(a)(5)). However, the device must still be labelled with the unique identifier (Verification). Generally, devices smaller than the palm of the hand are considered too small for the compliance statement.  Certification If the device is subject to Certification: (1) Section 2.925 contains information on identification of the equipment; (2) include a label bearing an FCC Identifier (FCC ID) (Section 2.926) and (3) include the appropriate compliance statement in Section 15.19(a). If the device is considered too small and therefore it is impractical (smaller than the palm of the hand) to display the compliance statement, then the statement may be placed in the user manual or product packaging. However, the device must still be labelled with the FCC ID. If the device is unquestionably too small for the FCC ID to be readable (smaller than 4-6 points), the FCC ID may be placed in the user manual. However, it must be determined that the device itself is too small – the label area allocated to the FCC ID may not be reduced because of over crowded identification of other product and regulatory information. An electronic display of the FCC ID (see 9. Electronic Labelling below) may be used for Certification of Section 15.212 modular transmitters and software defined radios (Section 2.944).  Declaration of Conformity (DoC): The labelling requirements for a device subject to the DoC procedure are specified in Section 15.19(b). The label should include the FCC logo along with the Trade Name and Model Number, which satisfies the unique identifier requirement of Section 2.1074 if it represents the identical equipment tested for DoC compliance. For personal computers assembled from authorized components, the following additional text must also be included: “Assembled from tested components,” “Complete system not tested.” When the device is so small and/or when it is not practical to place the required additional text on the device, the text may be placed in the user manual or pamphlet supplied to the user. However, the FCC logo, Trade Name, and Model Number must still be displayed on the device (Section 15.19(b)(3)). Part 15 Declaration of Conformity (DoC) Label Examples Equipment certified as software defined radio may use a means that readily displays the FCC ID on an electronic display screen, instead of labelling the device (Section 2.925 (e)). Further information may refer to FCC KDB:784748 D01 Labelling Part 15 &18 Guidelines Labelling Requirements for ICES-003 Devices:  Industry Canada ICES-003 Compliance Label: CAN ICES-3 (*)/NMB-3(*) * Insert either “A” or “B” but not both to identify the applicable Class of ITE. Report No.: FC150226E05 Page No. 8 / 24 Report Format Version: 6.1.0

4 Configuration and Connections with EUT 4.1 Connection Diagram of EUT and Peripheral Devices (2.4GHz+BT Link) 1 iPod shuffle (B) EUT NOTEBOOK 2 PCI-E Test Tool (E) PRINTER (C) COMPUTER (A) 3 MOUSE (D) Remote site (BT) (2.4GHz) NOTEBOOK WiFi AP (F) COMPUTER (G) Report No.: FC150226E05 Page No. 9 / 24 Report Format Version: 6.1.0

4.2 Configuration of Peripheral Devices and Cable Connections No. Product Brand Model No. Serial No. FCC ID Remark NOTEBOOK A DELL E5420 CHHYLQ1 FCC DoC Provided by Lab COMPUTER B iPod shuffle Apple MD778TA/A CC4JMFL0F4T1 NA Provided by Lab C PRINTER EPSON LQ-300+II G88Y074083 FCC DoC Provided by Lab D MOUSE DELL MOC5UO l1401LVG FCC DoC Provided by Lab Qualcomm E PCI-E Test Tool NA NA NA Supplied by Client Atheros F WiFi AP Linksys NA NA NA Provided by Lab NOTEBOOK G DELL PP32LA HSLB32S FCC DoC Provided by Lab COMPUTER NOTE: 1. All power cords of the above support units are non-shielded (1.8 m). 2. Items B-C acted as communication partners to transfer data. Shielded Cores No. Cable Qty. Length (m) Remark (Yes/ No) (Number) 1 USB 1 0.1 Yes 0 Provided by Lab 2 USB 1 1.8 Yes 0 Provided by Lab 3 USB 1 1.8 Yes 0 Provided by Lab 1. The core(s) is(are) originally attached to the cable(s). Report No.: FC150226E05 Page No. 10 / 24 Report Format Version: 6.1.0

5 Conducted Emissions at Mains Ports 5.1 Limits Class A (dBuV) Class B (dBuV) Frequency (MHz) Quasi-peak Average Quasi-peak Average 0.15 - 0.5 79 66 66 - 56 56 - 46 0.50 - 5.0 73 60 56 46 5.0 - 30.0 73 60 60 50 Notes: 1. The lower limit shall apply at the transition frequencies. 2. The limit decreases linearly with the logarithm of the frequency in the range of 0.15 to 0.50 MHz. 5.2 Test Instruments DESCRIPTION & CALIBRATED CALIBRATED MODEL NO. SERIAL NO. MANUFACTURER DATE UNTIL Test Receiver ESCS 30 100375 May 06, 2015 May 05, 2016 R&S Line-Impedance Stabilization Network NSLK-8127 8127-522 Sep. 15, 2014 Sep. 14, 2015 (for EUT) SCHWARZBECK Line-Impedance Stabilization Network ENV216 100072 June 11, 2015 June 10, 2016 (for Peripheral) R&S RF Cable 5D-FB COCCAB-001 Mar. 09, 2015 Mar. 08, 2016 50 ohms Terminator N/A EMC-03 Sep. 22, 2014 Sep. 21, 2015 50 ohms Terminator N/A EMC-02 Sep. 30, 2014 Sep. 29, 2015 Software BVADT_Cond_ NA NA NA BVADT V7.3.7.3 Note: 1. The calibration interval of the above test instruments are 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in Shielded Room No. C. 3 The VCCI Con C Registration No. is C-3611. 4 Tested Date: July 02, 2015 Report No.: FC150226E05 Page No. 11 / 24 Report Format Version: 6.1.0

5.3 Test Arrangement a. The EUT was placed 0.4 meters from the conducting wall of the shielded room with EUT being connected to the power mains through a line impedance stabilization network (LISN). Other support units were connected to the power mains through another LISN. The two LISNs provide 50 Ohm/ 50uH of coupling impedance for the measuring instrument. b. Both lines of the power mains connected to the EUT were checked for maximum conducted interference. c. The test results of conducted emissions at mains ports are recorded of six worst margins for quasi-peak (mandatory) [and average (if necessary)] values against the limits at frequencies of interest unless the margin is 20 dB or greater. Note: The resolution bandwidth and video bandwidth of test receiver is 9kHz for quasi-peak detection (QP) and average detection (AV) at frequency 0.15MHz-30MHz. For the actual test configuration, please refer to the related Item – Photographs of the Test Configuration. 5.4 Supplementary Information There is not any deviation from the test standards for the test method. Report No.: FC150226E05 Page No. 12 / 24 Report Format Version: 6.1.0

5.5 Test Results Detector Function Quasi-Peak (QP) / Frequency Range 150kHz ~ 30MHz & Resolution Average (AV), 9kHz Bandwidth Input Power Environmental 120Vac, 60Hz 25℃, 65%RH (System) Conditions Tested by Jyunchun Lin Phase Of Power : Line (L) Frequency Correction Reading Value Emission Level Limit Margin No Factor (dBuV) (dBuV) (dBuV) (dB) (MHz) (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.20859 0.09 54.62 41.79 54.71 41.88 63.26 53.26 -8.55 -11.38 2 0.29063 0.09 39.29 25.66 39.38 25.75 60.51 50.51 -21.12 -24.75 3 0.36484 0.10 33.47 16.74 33.57 16.84 58.62 48.62 -25.05 -31.78 4 0.79844 0.12 35.80 24.87 35.92 24.99 56.00 46.00 -20.08 -21.01 5 3.07422 0.20 28.95 23.46 29.15 23.66 56.00 46.00 -26.85 -22.34 6 9.00391 0.41 30.13 24.87 30.54 25.28 60.00 50.00 -29.46 -24.72 Remarks: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level – Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value Report No.: FC150226E05 Page No. 13 / 24 Report Format Version: 6.1.0

Detector Function Quasi-Peak (QP) / Frequency Range 150kHz ~ 30MHz & Resolution Average (AV), 9kHz Bandwidth Input Power Environmental 120Vac, 60Hz 25℃, 65%RH (System) Conditions Tested by Jyunchun Lin Phase Of Power : Neutral (N) Frequency Correction Reading Value Emission Level Limit Margin No Factor (dBuV) (dBuV) (dBuV) (dB) (MHz) (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.15000 0.08 48.96 25.63 49.04 25.71 66.00 56.00 -16.96 -30.29 2 0.21250 0.08 55.55 43.88 55.63 43.96 63.11 53.11 -7.48 -9.15 3 0.30234 0.09 42.86 27.20 42.95 27.29 60.18 50.18 -17.23 -22.89 4 0.79844 0.12 31.84 22.09 31.96 22.21 56.00 46.00 -24.04 -23.79 5 3.08203 0.20 29.90 24.71 30.10 24.91 56.00 46.00 -25.90 -21.09 6 11.96484 0.52 28.05 21.37 28.57 21.89 60.00 50.00 -31.43 -28.11 Remarks: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level – Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value Report No.: FC150226E05 Page No. 14 / 24 Report Format Version: 6.1.0

6 Radiated Emissions up to 1 GHz 6.1 Limits Emissions radiated outside of the specified bands, shall be according to the general radiated limits as following: Radiated Emissions Limits at 10 meters (dBμV/m) Frequencies FCC 15B / ICES-003, FCC 15B / ICES-003, CISPR 22, Class A CISPR 22, Class B (MHz) Class A Class B 30-88 39 29.5 88-216 43.5 33.1 40 30 216-230 46.4 35.6 230-960 47 37 960-1000 49.5 43.5 Radiated Emissions Limits at 3 meters (dBμV/m) Frequencies FCC 15B / ICES-003, FCC 15B / ICES-003, CISPR 22, Class A CISPR 22, Class B (MHz) Class A Class B 30-88 49.5 40 88-216 54 43.5 50.5 40.5 216-230 56.9 46 230-960 57.5 47.5 960-1000 60 54 Notes: 1. The lower limit shall apply at the transition frequencies. 2. Emission level (dBuV/m) = 20 log Emission level (uV/m). 3. QP detector shall be applied if not specified. 6.2 Test Instruments DESCRIPTION & CALIBRATED CALIBRATED MODEL NO. SERIAL NO. MANUFACTURER DATE UNTIL Test Receiver N9038A MY50010125 Apr. 18, 2015 Apr. 17, 2016 Agilent N9038A MY50010132 July 05, 2014 July 04, 2015 Pre-Amplifier ZFL-1000VH2B AMP-ZFL-01 Nov. 12, 2014 Nov. 11, 2015 Mini-Circuits ZFL-1000VH2B AMP-ZFL-02 Nov. 12, 2014 Nov. 11, 2015 Trilog Broadband VULB 9168 9168-359 Feb. 05, 2015 Feb. 04, 2016 Antenna VULB 9168 9168-358 Feb. 04, 2015 Feb. 03, 2016 SCHWARZBECK CHFCAB-001 RF Cable 8D-FB CHFCAB-002 Oct. 03, 2014 Oct. 02, 2015 CHFCAB-003 Software ADT_Radiated_ NA NA NA BVADT V8.7.07 Antenna Tower & Turn Table NA NA NA NA CT Note: 1. The calibration interval of the above test instruments are 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in 10m Chamber No. F. 3. The FCC Site Registration No. is 928149. 4. The VCCI Site Registration No. is R-3252 5. The CANADA Site Registration No. is IC 7450H-1. 6. Tested Date: July 02, 2015 Report No.: FC150226E05 Page No. 15 / 24 Report Format Version: 6.1.0

6.3 Test Arrangement a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at an accredited test facility. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 10 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The antenna is a broadband antenna, and its height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to quasi-peak detect function and specified bandwidth with maximum hold mode when the test frequency is below 1 GHz. Note: The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120kHz for quasi-peak detection (QP) at frequency below 1GHz. For the actual test configuration, please refer to the related Item – Photographs of the Test Configuration. 6.4 Supplementary Information There is not any deviation from the test standards for the test method. Report No.: FC150226E05 Page No. 16 / 24 Report Format Version: 6.1.0

6.5 Test Results Detector Function & Frequency Range 30MHz ~ 1GHz Quasi-Peak (QP), 120kHz Bandwidth Environmental Input Power 3.3Vdc from hsot equipment 25℃, 55%RH Conditions Tested by Mike Hsieh Antenna Polarity & Test Distance : Horizontal at 10 m Emission Antenna Table Raw Correction Frequency Limit Margin No Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 99.94 20.59 QP 30.00 -9.41 4.00 H 34 37.46 -16.87 2 136.22 22.02 QP 30.00 -7.98 4.00 H 199 35.18 -13.16 3 298.79 20.07 QP 37.00 -16.93 3.00 H 355 31.30 -11.23 4 339.24 22.41 QP 37.00 -14.59 3.00 H 14 32.46 -10.05 5 594.01 25.38 QP 37.00 -11.62 1.00 H 14 28.47 -3.09 6 791.98 25.73 QP 37.00 -11.27 1.00 H 14 24.87 0.86 Remarks: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor (dB/m) + Cable Factor (dB) – Pre-Amplifier Factor (dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission level – Limit value Report No.: FC150226E05 Page No. 17 / 24 Report Format Version: 6.1.0

Detector Function & Frequency Range 30MHz ~ 1GHz Quasi-Peak (QP), 120kHz Bandwidth Environmental Input Power 3.3Vdc from hsot equipment 25℃, 55%RH Conditions Tested by Mike Hsieh Antenna Polarity & Test Distance : Vertical at 10 m Emission Antenna Table Raw Correction Frequency Limit Margin No Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 73.50 25.95 QP 30.00 -4.05 1.00 V 326 41.68 -15.73 2 98.92 23.87 QP 30.00 -6.13 2.00 V 161 41.04 -17.17 3 136.80 24.26 QP 30.00 -5.74 2.00 V 242 37.28 -13.02 4 298.79 25.73 QP 37.00 -11.27 1.00 V 127 36.86 -11.13 5 340.55 24.38 QP 37.00 -12.62 1.00 V 190 34.34 -9.96 6 594.01 24.85 QP 37.00 -12.15 4.00 V 129 27.95 -3.10 Remarks: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor (dB/m) + Cable Factor (dB) – Pre-Amplifier Factor (dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission level – Limit value Report No.: FC150226E05 Page No. 18 / 24 Report Format Version: 6.1.0

7 Radiated Emissions above 1 GHz 7.1 Limits Emissions radiated outside of the specified bands, shall be according to the general radiated limits as following: Radiated Emissions Limits at 10 meters (dBμV/m) Frequencies FCC 15B / ICES-003, FCC 15B / ICES-003, CISPR 22, Class A CISPR 22, Class B (MHz) Class A Class B 1000-3000 Avg: 49.5 Avg: 43.5 Not defined Not defined Above 3000 Peak: 69.5 Peak: 63.5 Not defined Not defined Radiated Emissions Limits at 3 meters (dBμV/m) Frequencies FCC 15B / ICES-003, FCC 15B / ICES-003, CISPR 22, Class A CISPR 22, Class B (MHz) Class A Class B Avg: 56 Avg: 50 1000-3000 Avg: 60 Avg: 54 Peak: 76 Peak: 70 Peak: 80 Peak: 74 Avg: 60 Avg: 54 Above 3000 Peak: 80 Peak: 74 Notes: 1. The lower limit shall apply at the transition frequencies. 2. Emission level (dBuV/m) = 20 log Emission level (uV/m). 3. As shown in 15.35(b), for frequencies above 1000MHz, the field strength limits are based on average detector, however, the peak field strength of any emission shall not exceed the maximum permitted average limits, specified above by more than 20dB under any condition of modulation. Frequency Range (For unintentional radiators) Highest frequency generated or used in the device or Upper frequency of measurement range (MHz) on which the device operates or tunes (MHz) Below 1.705 30 1.705-108 1000 108-500 2000 500-1000 5000 5th harmonic of the highest frequency or 40GHz, Above 1000 whichever is lower Report No.: FC150226E05 Page No. 19 / 24 Report Format Version: 6.1.0

7.2 Test Instruments DESCRIPTION & CALIBRATED CALIBRATED MODEL NO. SERIAL NO. MANUFACTURER DATE UNTIL Test Receiver N9038A MY50010125 Apr. 18, 2015 Apr. 17, 2016 Agilent Pre-Amplifier 8449B 3008A01975 Feb. 28, 2015 Feb. 27, 2016 Agilent Horn Antenna BBHA 9120D D123 Feb. 05, 2015 Feb. 04, 2016 SCHWARZBECK RF-104-206 RF Cable SUCOFLEX104 RF-104-209 Dec. 11, 2014 Dec.10, 2015 RF-104-110 Spectrum Analyzer E4446A MY48250254 Nov. 19, 2014 Nov. 18, 2015 Agilent Pre-Amplifier EMC184045 980143 Jan. 16, 2015 Jan. 15, 2016 EMCI Horn Antenna BBHA 9170 9170-424 Feb. 05, 2015 Feb. 04, 2016 SCHWARZBECK 36442/2 RF Cable SUCOFLEX 102 Jan. 17, 2015 Jan. 16, 2016 36434/2 Software ADT_Radiated_ NA NA NA BVADT V8.7.07 Antenna Tower & Turn Table NA NA NA NA CT Note: 1. The calibration interval of the above test instruments are 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in 10m Chamber No. F. 3. Tested Date: July 02, 2015 Report No.: FC150226E05 Page No. 20 / 24 Report Format Version: 6.1.0

7.3 Test Arrangement a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at an accredited chamber room. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The height of antenna can be varied from one meter to four meters, the height of adjustment depends on the EUT height and the antenna 3dB beamwidth both, to detect the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The spectrum analyzer system was set to peak and average detect function and specified bandwidth with maximum hold mode when the test frequency is above 1 GHz. Note: The resolution bandwidth of test receiver/spectrum analyzer is 1MHz and video bandwidth is 3MHz for Peak detection (PK) at frequency above 1GHz. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz for Average detection (AV) at frequency above 1GHz. <Frequency Range above 1GHz> Ant. Tower 1 - 4m* Variable EUT& 3m Support Units Turn Table Absorber 80cm Ground Plane Test Receiver * : depends on the EUT height and the antenna 3dB beamwidth both. For the actual test configuration, please refer to the related Item – Photographs of the Test Configuration. 7.4 Supplementary Information There is not any deviation from the test standards for the test method. Report No.: FC150226E05 Page No. 21 / 24 Report Format Version: 6.1.0

7.5 Test Results Detector Function & Peak (PK) / Frequency Range 1GHz ~ 40GHz Resolution Average (AV), 1MHz Bandwidth Environmental Input Power 3.3Vdc from hsot equipment 25℃, 56%RH Conditions Tested by Mike Hsieh Antenna Polarity & Test Distance : Horizontal at 3 m Emission Antenna Table Raw Correction Frequency Limit Margin No Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 1098.25 44.82 PK 74.00 -29.18 1.00 H 327 48.80 -3.98 2 1098.25 27.97 AV 54.00 -26.03 1.00 H 327 31.95 -3.98 3 1187.25 43.26 PK 74.00 -30.74 1.00 H 126 46.41 -3.15 4 1187.25 25.18 AV 54.00 -28.82 1.00 H 126 28.33 -3.15 5 1863.00 43.44 PK 74.00 -30.56 1.00 H 271 43.00 0.44 6 1863.00 26.15 AV 54.00 -27.85 1.00 H 271 25.71 0.44 7 1995.50 44.11 PK 74.00 -29.89 1.00 H 53 43.41 0.70 8 1995.50 26.66 AV 54.00 -27.34 1.00 H 53 25.96 0.70 9 2491.00 47.43 PK 74.00 -26.57 1.00 H 250 43.62 3.81 10 2491.00 29.40 AV 54.00 -24.60 1.00 H 250 25.59 3.81 11 2987.75 43.68 PK 74.00 -30.32 1.00 H 269 37.71 5.97 12 2987.75 29.96 AV 54.00 -24.04 1.00 H 269 23.99 5.97 Remarks: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor (dB/m) + Cable Factor (dB) – Pre-Amplifier Factor (dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission level – Limit value Report No.: FC150226E05 Page No. 22 / 24 Report Format Version: 6.1.0

Detector Function & Peak (PK) / Frequency Range 1GHz ~ 40GHz Resolution Average (AV), 1MHz Bandwidth Environmental Input Power 3.3Vdc from hsot equipment 25℃, 56%RH Conditions Tested by Mike Hsieh Antenna Polarity & Test Distance : Vertical at 3 m Emission Antenna Table Raw Correction Frequency Limit Margin No Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 1097.00 40.70 PK 74.00 -33.30 1.00 V 286 44.68 -3.98 2 1097.00 24.61 AV 54.00 -29.39 1.00 V 286 28.59 -3.98 3 1897.00 46.60 PK 74.00 -27.40 1.00 V 310 45.99 0.61 4 1897.00 26.54 AV 54.00 -27.46 1.00 V 310 25.93 0.61 5 1993.00 51.23 PK 74.00 -22.77 1.00 V 58 50.53 0.70 6 1993.00 27.87 AV 54.00 -26.13 1.00 V 58 27.17 0.70 7 2496.00 49.59 PK 74.00 -24.41 1.00 V 232 45.75 3.84 8 2496.00 30.02 AV 54.00 -23.98 1.00 V 232 26.18 3.84 9 5016.50 47.35 PK 74.00 -26.65 1.00 V 50 35.87 11.48 10 5016.50 33.25 AV 54.00 -20.75 1.00 V 50 21.77 11.48 11 5757.75 47.44 PK 74.00 -26.56 1.00 V 198 34.57 12.87 12 5757.75 34.08 AV 54.00 -19.92 1.00 V 198 21.21 12.87 Remarks: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor (dB/m) + Cable Factor (dB) – Pre-Amplifier Factor (dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission level – Limit value Report No.: FC150226E05 Page No. 23 / 24 Report Format Version: 6.1.0

Appendix – Information on the Testing Laboratories We, Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, were founded in 1988 to provide our best service in EMC, Radio, Telecom and Safety consultation. Our laboratories are accredited and approved according to ISO/IEC 17025. If you have any comments, please feel free to contact us at the following: Linko EMC/RF Lab Hsin Chu EMC/RF/Telecom Lab Tel: 886-2-26052180 Tel: 886-3-5935343 Fax: 886-2-26051924 Fax: 886-3-5935342 Hwa Ya EMC/RF/Safety Lab Tel: 886-3-3183232 Fax: 886-3-3270892 Email: service.adt@tw.bureauveritas.com Web Site: www.bureauveritas-adt.com The address and road map of all our labs can be found in our web site also. --- END --- Report No.: FC150226E05 Page No. 24 / 24 Report Format Version: 6.1.0


Document Created: 2019-11-07 13:26:19
Document Modified: 2019-11-07 13:26:19
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC