Test Report_NII

FCC ID: PPD-AR5B22

Test Report

Download: PDF
FCCID_2456929

PARTIAL FCC TEST REPORT (15.407) REPORT NO.: RF140728C21-1 MODEL NO.: AR5B22 FCC ID: PPD-AR5B22 RECEIVED: Jul. 28, 2014 TESTED: Sep. 01 ~ Sep. 05, 2014 ISSUED: Sep. 10, 2014 APPLICANT: Qualcomm Atheros, Inc. ADDRESS: 1700 Technology Drive, San Jose, CA 95110 ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. Report No.: RF140728C21-1 1 of 28 Report Format Version 5.2.1

TABLE OF CONTENTS RELEASE CONTROL RECORD .............................................................................................. 3 1. CERTIFICATION........................................................................................................... 4 2. SUMMARY OF TEST RESULTS .................................................................................. 5 2.1 MEASUREMENT UNCERTAINTY ................................................................................ 5 3. GENERAL INFORMATION ........................................................................................... 6 3.1 GENERAL DESCRIPTION OF EUT ............................................................................. 6 3.2 DESCRIPTION OF TEST MODES ............................................................................... 7 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ............................... 8 3.3 DESCRIPTION OF SUPPORT UNITS ......................................................................... 9 3.3.1 CONFIGURATION OF SYSTEM UNDER TEST .......................................................... 9 3.4 GENERAL DESCRIPTION OF APPLIED STANDARDS ............................................ 10 4. TEST TYPES AND RESULTS .................................................................................... 11 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT ..................................... 11 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT .................. 11 4.1.2 LIMITS OF UNWANTED EMISSION OUT OF THE RESTRICTED BANDS .............. 11 4.1.3 TEST INSTRUMENTS ................................................................................................ 12 4.1.4 TEST PROCEDURES ................................................................................................ 13 4.1.5 DEVIATION FROM TEST STANDARD....................................................................... 13 4.1.6 TEST SETUP .............................................................................................................. 14 4.1.7 EUT OPERATING CONDITION.................................................................................. 14 4.1.8 TEST RESULTS ......................................................................................................... 15 4.2 CONDUCTED EMISSION MEASUREMENT ............................................................. 22 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ........................................... 22 4.2.2 TEST INSTRUMENTS ................................................................................................ 22 4.2.3 TEST PROCEDURES ................................................................................................ 23 4.2.4 DEVIATION FROM TEST STANDARD....................................................................... 23 4.2.5 TEST SETUP .............................................................................................................. 23 4.2.6 EUT OPERATING CONDITIONS ............................................................................... 23 4.2.7 TEST RESULTS ......................................................................................................... 24 5. PHOTOGRAPHS OF THE TEST CONFIGURATION ................................................. 26 6. INFORMATION ON THE TESTING LABORATORIES ............................................... 27 7. APPENDIX A – MODIFICATIONS RECORDERS FOR ENGINEERING CHANGES TO THE EUT BY THE LAB ......................................................................................... 28 Report No.: RF140728C21-1 2 of 28 Report Format Version 5.2.1

RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED RF140728C21-1 Original release Sep. 10, 2014 Report No.: RF140728C21-1 3 of 28 Report Format Version 5.2.1

1. CERTIFICATION PRODUCT: PCIE 802.11a/b/g/n 2.4GHz/5GHz + USB BT 4.0 card MODEL: AR5B22 BRAND: Atheros APPLICANT: Qualcomm Atheros, Inc. TESTED: Sep. 01 ~ Sep. 05, 2014 TEST SAMPLE: ENGINEERING SAMPLE STANDARDS: FCC Part 15, Subpart E (Section 15.407) ANSI C63.10-2009 The above equipment (model: AR5B22) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE : Sep. 10, 2014 Pettie Chen / Senior Specialist APPROVED BY : , DATE : Sep. 10, 2014 Ken Liu / Senior Manager Report No.: RF140728C21-1 4 of 28 Report Format Version 5.2.1

2. SUMMARY OF TEST RESULTS The EUT has been tested according to the following specifications: APPLIED STANDARD: FCC PART 15, SUBPART E (SECTION 15.407) STANDARD TEST TYPE RESULT REMARK SECTION Meet the requirement of limit. 15.407(b)(6) AC Power Conducted Emission PASS Minimum passing margin is -16.72dB at 0.43906MHz. Meet the requirement of limit. 15.407(b/1/2/3) Radiated Emissions PASS Minimum passing margin is (b)(6) -3.2dB at 10600.00MHz. 2.1 MEASUREMENT UNCERTAINTY Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16-4-2: MEASUREMENT FREQUENCY UNCERTAINTY Conducted emissions 9kHz~30MHz 2.44 dB 30MHz ~ 200MHz 3.63 dB 200MHz ~1000MHz 3.64 dB Radiated emissions 1GHz ~ 18GHz 2.29 dB 18GHz ~ 40GHz 2.29 dB This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k = 2. Report No.: RF140728C21-1 5 of 28 Report Format Version 5.2.1

3. GENERAL INFORMATION 3.1 GENERAL DESCRIPTION OF EUT EUT PCIE 802.11a/b/g/n 2.4GHz/5GHz + USB BT 4.0 card MODEL NO. AR5B22 POWER SUPPLY 3.3Vdc (host equipment) MODULATION TYPE 64QAM, 16QAM, QPSK, BPSK MODULATION TECHNOLOGY OFDM 802.11a: 54.0/ 48.0/ 36.0/ 24.0/ 18.0/ 12.0/ 9.0/ 6.0Mbps TRANSFER RATE 802.11n: up to 300.0Mbps OPERATING FREQUENCY 5180 ~ 5240MHz, 5260 ~ 5320MHz & 5500 ~ 5700MHz 5180 ~ 5240MHz: 4 for 802.11a, 802.11n (20MHz) 2 for 802.11n (40MHz) 5260 ~ 5320MHz: 4 for 802.11a, 802.11n (20MHz) NUMBER OF CHANNEL 2 for 802.11n (40MHz) 5500 ~ 5700MHz: 8 for 802.11a, 802.11n (20MHz) 3 for 802.11n (40MHz) ANTENNA TYPE Refer to Note ANTENNA CONNECTOR Refer to Note DATA CABLE N/A I/O PORTS Refer to user’s manual ACCESSORY DEVICES N/A NOTE: 1. This report is prepared for FCC class II permissive change. This report is issued as a supplementary report of BV ADT report no.: RF110907E02-1 R1. The differences compared with the original design are as below: * Adding specific host portable * Adding antenna (same type/low gain) Only AC Power Conducted Emission & Radiated Emissions had been re-tested. 2. The EUT incorporates a MIMO function. Physically, the EUT provides two completed transmitters and two receivers. MODULATION MODE TX FUNCTION 802.11a 1TX/2TX 802.11n (20MHz) 1TX/2TX 802.11n (40MHz) 1TX/2TX 3. There is one set of antenna provided to this EUT, please refer to the following table: Antenna Gain (dBi) No Brand Model Antenna Type Connector 2.4GHz 5.18 GHz 5.32 GHz 5.5 GHz 5.745 GHz Main EM24580409 IPEX 0.497932 -1.24142 -1.21835 -1.12629 1.56537 PENSON PIFA Aux EM24580410 IPEX 2.71072 3.03969 2.23989 2.81597 3.51485 4. The above EUT information is declared by manufacturer and for more detailed features description, please refer to the manufacturer's specifications or user's manual. Report No.: RF140728C21-1 6 of 28 Report Format Version 5.2.1

3.2 DESCRIPTION OF TEST MODES FOR 5180 ~ 5240MHz 4 channels are provided for 802.11a, 802.11n (20MHz): CHANNEL FREQUENCY CHANNEL FREQUENCY 36 5180 MHz 44 5220 MHz 40 5200 MHz 48 5240 MHz 2 channels are provided for 802.11n (40MHz): CHANNEL FREQUENCY CHANNEL FREQUENCY 38 5190 MHz 46 5230 MHz FOR 5260 ~ 5320MHz 4 channels are provided for 802.11a, 802.11n (20MHz): CHANNEL FREQUENCY CHANNEL FREQUENCY 52 5260 MHz 60 5300 MHz 56 5280 MHz 64 5320 MHz 2 channels are provided for 802.11n (40MHz): CHANNEL FREQUENCY CHANNEL FREQUENCY 54 5270 MHz 62 5310 MHz FOR 5500 ~ 5700MHz 8 channels are provided for 802.11a, 802.11n (20MHz): CHANNEL FREQUENCY CHANNEL FREQUENCY 100 5500 MHz 116 5580 MHz 104 5520 MHz 132 5660 MHz 108 5540 MHz 136 5680 MHz 112 5560 MHz 140 5700 MHz 3 channels are provided for 802.11n (40MHz): CHANNEL FREQUENCY CHANNEL FREQUENCY 102 5510 MHz 134 5670 MHz 110 5550 MHz Report No.: RF140728C21-1 7 of 28 Report Format Version 5.2.1

3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL EUT APPLICABLE TO CONFIGURE DESCRIPTION MODE RE1G RE<1G PLC - √ √ √ - Where RE1G: Radiated Emission above 1GHz RE<1G: Radiated Emission below 1GHz PLC: Power Line Conducted Emission NOTE: 1. The EUT had been pre-tested on the positioned of each 3 axis. The worst case was found when positioned on X-plane. 2. According the worst case of original test report, only the following channels were chosen for final test. RADIATED EMISSION TEST (ABOVE 1GHz): Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. FREQ. BAND AVAILABLE TESTED MODULATION MODULATION DATA RATE TX MODE (MHz) CHANNEL CHANNEL TECHNOLOGY TYPE (Mbps) FUNCTION 802.11a 36 to 48 36 OFDM BPSK 6.0 1TX 5180-5240 802.11n (40MHz) 38 to 46 46 OFDM BPSK 13.5 2TX 802.11a 52 to 64 60 OFDM BPSK 6.0 1TX 5260-5320 802.11a 52 to 64 60 OFDM BPSK 6.0 2TX 802.11a 100 to 140 116 OFDM BPSK 6.0 1TX 5500-5700 802.11n (20MHz) 100 to 140 116 OFDM BPSK 6.5 2TX RADIATED EMISSION TEST (BELOW 1GHz): Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. FREQ. BAND AVAILABLE TESTED MODULATION MODULATION DATA RATE TX MODE FUNCTION (MHz) CHANNEL CHANNEL TECHNOLOGY TYPE (Mbps) 802.11a 5180-5320 36 to 64 36 OFDM BPSK 6.0 1TX POWER LINE CONDUCTED EMISSION TEST: Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. FREQ. BAND AVAILABLE TESTED MODULATION MODULATION DATA RATE TX MODE FUNCTION (MHz) CHANNEL CHANNEL TECHNOLOGY TYPE (Mbps) 802.11a 5180-5320 36 to 64 36 OFDM BPSK 6.0 1TX Report No.: RF140728C21-1 8 of 28 Report Format Version 5.2.1

TEST CONDITION: ENVIRONMENTAL INPUT POWER APPLICABLE TO TESTED BY CONDITIONS (SYSTEM) RE1G 25deg. C, 65%RH 120Vac, 60Hz Ted Chang RE<1G 25deg. C, 65%RH 120Vac, 60Hz Ted Chang PLC 20deg. C, 70%RH 120Vac, 60Hz Nick Hsu 3.3 DESCRIPTION OF SUPPORT UNITS The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. NO. PRODUCT BRAND MODEL NO. SERIAL NO. FCC ID entegra 1 Crossfire 940-10-972 NA NA technologies inc. 2 Adapter of Crossfire FSP GROUP INC. FSP060-DBAE1 NA NA NO. SIGNAL CABLE DESCRIPTION OF THE ABOVE SUPPORT UNITS 1 NA 2 NA NOTE: 1. All power cords of the above support units are non shielded (1.8m). 2. Item 1, 2 were provided by client. 3.3.1 CONFIGURATION OF SYSTEM UNDER TEST EUT Crossfire (Power from host equipment) *Test table Report No.: RF140728C21-1 9 of 28 Report Format Version 5.2.1

3.4 GENERAL DESCRIPTION OF APPLIED STANDARDS The EUT is a RF Product. According to the specifications of the manufacturer, it must comply with the requirements of the following standards: FCC Part 15, Subpart E (15.407) 789033 D01 General UNII Test Procedures Old Rules v01r04 662911 D01 Multiple Transmitter Output v02r01 ANSI C63.10-2009 All test items have been performed and recorded as per the above standards. NOTE: The EUT is also considered as a kind of computer peripheral, because the connection to computer is necessary for typical use. It has been verified to comply with the requirements of FCC Part 15, Subpart B, Class B (DoC). The test report has been issued separately. Report No.: RF140728C21-1 10 of 28 Report Format Version 5.2.1

4. TEST TYPES AND RESULTS 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT Radiated emissions which fall in the restricted bands must comply with the radiated emission limits specified as below table: FREQUENCIES FIELD STRENGTH MEASUREMENT DISTANCE (MHz) (microvolts/meter) (meters) 0.009 ~ 0.490 2400/F(kHz) 300 0.490 ~ 1.705 24000/F(kHz) 30 1.705 ~ 30.0 30 30 30 ~ 88 100 3 88 ~ 216 150 3 216 ~ 960 200 3 Above 960 500 3 NOTE: 1. The lower limit shall apply at the transition frequencies. 2. Emission level (dBuV/m) = 20 log Emission level (uV/m). 3. For frequencies above 1000MHz, the field strength limits are based on average detector, however, the peak field strength of any emission shall not exceed the maximum permitted average limits, specified above by more than 20dB under any condition of modulation. 4.1.2 LIMITS OF UNWANTED EMISSION OUT OF THE RESTRICTED BANDS APPLICABLE TO LIMIT FIELD STRENGTH AT 3m (dBµV/m)  PK AV 74 54 EQUIVALENT FIELD STRENGTH AT 3m EIRP LIMIT (dBm) (dBµV/m) PK PK -27 68.3 NOTE: The following formula is used to convert the equipment isotropic radiated power (eirp) to field strength: 1000000 30 P E= µV/m, where P is the eirp (Watts). 3 Report No.: RF140728C21-1 11 of 28 Report Format Version 5.2.1

4.1.3 TEST INSTRUMENTS DESCRIPTION & DATE OF DUE DATE OF MODEL NO. SERIAL NO. MANUFACTURER CALIBRATION CALIBRATION Test Receiver ESCS30 100289 Nov. 29, 2013 Nov. 28, 2014 ROHDE & SCHWARZ Spectrum Analyzer FSP40 100269 Feb. 11, 2014 Feb. 10, 2015 ROHDE & SCHWARZ BILOG Antenna VULB9168 9168-156 Feb. 25, 2014 Feb. 24, 2015 SCHWARZBECK HORN Antenna BBHA 9120 D 9120D-209 Sep. 12, 2013 Sep. 11, 2014 SCHWARZBECK HORN Antenna BBHA 9170 BBHA9170241 Feb. 17, 2014 Feb. 16, 2015 SCHWARZBECK Preamplifier 8449B 3008A01961 Oct. 28, 2013 Oct. 27, 2014 Agilent Preamplifier 8447D 2944A10638 Oct. 18, 2013 Oct. 17, 2014 Agilent RF signal cable 309219/4 SUCOFLEX 104 Oct. 18, 2013 Oct. 17, 2014 HUBER+SUHNNER 2950114 RF signal cable SUCOFLEX 104 250130/4 Oct. 18, 2013 Oct. 17, 2014 HUBER+SUHNNER RF signal cable 5D-FB Cable-HYCH9-01 Aug. 11, 2014 Aug. 10, 2015 Worken Software ADT_Radiated_ NA NA NA BV ADT V7.6.15.9.4 Antenna Tower 2070/2080 512.835.4684 NA NA EMCO Turn Table 2087-2.03 NA NA NA EMCO Antenna Tower &Turn Table Controller 2090 NA NA NA EMCO 26GHz ~ 40GHz Amplifier EM26400 815221 Oct. 18, 2013 Oct. 17, 2014 NOTE: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in HwaYa Chamber 9. 3. The horn antenna and HP preamplifier (model: 8449B) are used only for the measurement of emission frequency above 1GHz if tested. 4. The FCC Site Registration No. is 460141. 5. The IC Site Registration No. is IC 7450F-4. Report No.: RF140728C21-1 12 of 28 Report Format Version 5.2.1

4.1.4 TEST PROCEDURES a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter semi-anechoic camber. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The antenna is a broadband antenna, and its height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. f. If the emission level of the EUT in peak mode was 10dB lower than the limit specified, then testing could be stopped and the peak values of the EUT would be reported. Otherwise the emissions that did not have 10dB margin would be re-tested one by one using peak, quasi-peak or average method as specified and then reported in a data sheet. NOTE: 1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120kHz for Quasi-peak detection at frequency below 1GHz. 2. The resolution bandwidth of test receiver/spectrum analyzer is 1MHz and video bandwidth is 3MHz for Peak detection at frequency above 1GHz. 3. The resolution bandwidth of test receiver/spectrum analyzer is 1MHz and the video bandwidth is ≥ 1/T (Duty cycle < 98%) or 10Hz(Duty cycle > 98%) for Average detection (AV) at frequency above 1GHz. 4. All modes of operation were investigated and the worst-case emissions are reported. 4.1.5 DEVIATION FROM TEST STANDARD No deviation. Report No.: RF140728C21-1 13 of 28 Report Format Version 5.2.1

4.1.6 TEST SETUP Frequency range 30MHz~1GHz Frequency range above 1GHz For the actual test configuration, please refer to the attached file (Test Setup Photo). 4.1.7 EUT OPERATING CONDITION Installed the EUT in the Crossfire and set the EUT under transmission condition continuously at specific channel frequency. Report No.: RF140728C21-1 14 of 28 Report Format Version 5.2.1

4.1.8 TEST RESULTS ABOVE 1GHz DATA： 802.11a_1TX CHANNEL TX Channel 36 DETECTOR Peak (PK) FREQUENCY RANGE 1GHz ~ 40GHz FUNCTION Average (AV) ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 5150.00 65.4 PK 74.0 -8.6 1.00 H 133 63.40 2.00 2 5150.00 46.2 AV 54.0 -7.8 1.00 H 133 44.20 2.00 3 *5180.00 103.9 PK 1.00 H 134 63.90 40.00 4 *5180.00 93.0 AV 1.00 H 134 53.00 40.00 5 #10360.00 60.5 PK 74.0 -13.5 1.00 H 141 45.90 14.60 6 #10360.00 46.6 AV 54.0 -7.4 1.00 H 141 32.00 14.60 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 5150.00 61.1 PK 74.0 -12.9 1.12 V 216 59.10 2.00 2 5150.00 43.8 AV 54.0 -10.2 1.12 V 216 41.80 2.00 3 *5180.00 100.5 PK 1.12 V 216 60.50 40.00 4 *5180.00 89.2 AV 1.12 V 216 49.20 40.00 5 #10360.00 60.5 PK 74.0 -13.5 1.54 V 74 45.90 14.60 6 #10360.00 47.1 AV 54.0 -6.9 1.54 V 74 32.50 14.60 REMARKS: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level – Limit value 5. " * ": Fundamental frequency. 6. " # ": The radiated frequency is out of the restricted band. Report No.: RF140728C21-1 15 of 28 Report Format Version 5.2.1

802.11n (40MHz)_2TX CHANNEL TX Channel 46 DETECTOR Peak (PK) FREQUENCY RANGE 1GHz ~ 40GHz FUNCTION Average (AV) ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 *5230.00 104.6 PK 1.01 H 317 64.50 40.10 2 *5230.00 93.8 AV 1.01 H 317 53.70 40.10 3 #10460.00 61.8 PK 74.0 -12.2 1.00 H 174 46.50 15.30 4 #10460.00 48.5 AV 54.0 -5.5 1.00 H 174 33.20 15.30 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 *5230.00 101.0 PK 1.00 V 28 60.90 40.10 2 *5230.00 89.9 AV 1.00 V 28 49.80 40.10 3 #10460.00 62.6 PK 74.0 -11.4 1.03 V 137 47.30 15.30 4 #10460.00 48.9 AV 54.0 -5.1 1.03 V 137 33.60 15.30 REMARKS: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level – Limit value 5. " * ": Fundamental frequency. 6. " # ": The radiated frequency is out of the restricted band. Report No.: RF140728C21-1 16 of 28 Report Format Version 5.2.1

802.11a_1TX CHANNEL TX Channel 60 DETECTOR Peak (PK) FREQUENCY RANGE 1GHz ~ 40GHz FUNCTION Average (AV) ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 *5300.00 111.2 PK 1.00 H 132 71.10 40.10 2 *5300.00 100.5 AV 1.00 H 132 60.40 40.10 3 10600.00 62.4 PK 74.0 -11.6 1.54 H 52 45.80 16.60 4 10600.00 49.1 AV 54.0 -4.9 1.54 H 52 32.50 16.60 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 *5300.00 105.1 PK 1.00 V 196 65.00 40.10 2 *5300.00 94.3 AV 1.00 V 196 54.20 40.10 3 10600.00 61.9 PK 74.0 -12.1 1.04 V 51 45.30 16.60 4 10600.00 49.1 AV 54.0 -4.9 1.04 V 51 32.50 16.60 REMARKS: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level – Limit value 5. " * ": Fundamental frequency. Report No.: RF140728C21-1 17 of 28 Report Format Version 5.2.1

802.11a_2TX CHANNEL TX Channel 60 DETECTOR Peak (PK) FREQUENCY RANGE 1GHz ~ 40GHz FUNCTION Average (AV) ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 *5300.00 110.6 PK 1.00 H 316 70.50 40.10 2 *5300.00 100.2 AV 1.00 H 316 60.10 40.10 3 10600.00 61.2 PK 74.0 -12.8 1.05 H 35 44.60 16.60 4 10600.00 48.8 AV 54.0 -5.2 1.05 H 35 32.20 16.60 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 *5300.00 106.4 PK 1.00 V 30 66.30 40.10 2 *5300.00 96.3 AV 1.00 V 30 56.20 40.10 3 10600.00 65.6 PK 74.0 -8.4 1.00 V 349 49.00 16.60 4 10600.00 50.8 AV 54.0 -3.2 1.00 V 349 34.20 16.60 REMARKS: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level – Limit value 5. " * ": Fundamental frequency. Report No.: RF140728C21-1 18 of 28 Report Format Version 5.2.1

802.11a_1TX CHANNEL TX Channel 116 DETECTOR Peak (PK) FREQUENCY RANGE 1GHz ~ 40GHz FUNCTION Average (AV) ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 *5580.00 109.4 PK 1.05 H 114 68.90 40.50 2 *5580.00 98.6 AV 1.05 H 114 58.10 40.50 3 11160.00 62.0 PK 74.0 -12.0 1.54 H 184 44.40 17.60 4 11160.00 46.9 AV 54.0 -7.1 1.54 H 184 29.30 17.60 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 *5580.00 105.1 PK 1.00 V 197 64.60 40.50 2 *5580.00 94.4 AV 1.00 V 197 53.90 40.50 3 11160.00 62.9 PK 74.0 -11.1 1.51 V 32 45.30 17.60 4 11160.00 49.7 AV 54.0 -4.3 1.51 V 32 32.10 17.60 REMARKS: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level – Limit value 5. " * ": Fundamental frequency. Report No.: RF140728C21-1 19 of 28 Report Format Version 5.2.1

802.11n (20MHz)_2TX CHANNEL TX Channel 116 DETECTOR Peak (PK) FREQUENCY RANGE 1GHz ~ 40GHz FUNCTION Average (AV) ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 *5580.00 108.2 PK 1.00 H 328 67.70 40.50 2 *5580.00 98.0 AV 1.00 H 328 57.50 40.50 3 11160.00 59.8 PK 74.0 -14.2 1.05 H 32 42.20 17.60 4 11160.00 48.1 AV 54.0 -5.9 1.05 H 32 30.50 17.60 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 *5580.00 105.4 PK 1.00 V 299 64.90 40.50 2 *5580.00 94.6 AV 1.00 V 299 54.10 40.50 3 11160.00 62.1 PK 74.0 -11.9 1.12 V 5 44.50 17.60 4 11160.00 48.3 AV 54.0 -5.7 1.12 V 5 30.70 17.60 REMARKS: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level – Limit value 5. " * ": Fundamental frequency. Report No.: RF140728C21-1 20 of 28 Report Format Version 5.2.1

BELOW 1GHz WORST-CASE DATA 802.11a_1TX CHANNEL TX Channel 36 DETECTOR Quasi-Peak (QP) FREQUENCY RANGE 30MHz ~ 1GHz FUNCTION ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 95.20 31.8 QP 43.5 -11.7 1.99 H 15 51.10 -19.30 2 143.80 38.1 QP 43.5 -5.4 1.10 H 313 52.50 -14.40 3 264.80 39.9 QP 46.0 -6.1 1.00 H 187 53.60 -13.70 4 432.50 36.3 QP 46.0 -9.7 1.99 H 215 45.80 -9.50 5 501.10 34.6 QP 46.0 -11.4 1.99 H 70 43.20 -8.60 6 575.70 33.5 QP 46.0 -12.5 1.24 H 214 40.60 -7.10 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 89.30 30.6 QP 43.5 -12.9 1.49 V 28 50.40 -19.80 2 143.60 30.1 QP 43.5 -13.4 1.99 V 261 44.50 -14.40 3 264.80 32.0 QP 46.0 -14.0 1.24 V 81 45.70 -13.70 4 333.10 34.5 QP 46.0 -11.5 1.24 V 15 46.20 -11.70 5 432.50 36.6 QP 46.0 -9.4 1.24 V 283 46.10 -9.50 6 583.60 37.7 QP 46.0 -8.3 1.00 V 6 44.40 -6.70 REMARKS: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level – Limit value Report No.: RF140728C21-1 21 of 28 Report Format Version 5.2.1

4.2 CONDUCTED EMISSION MEASUREMENT 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT FREQUENCY OF EMISSION (MHz) CONDUCTED LIMIT (dBµV) Quasi-peak Average 0.15 ~ 0.5 66 to 56 56 to 46 0.5 ~ 5 56 46 5 ~ 30 60 50 NOTE: 1. The lower limit shall apply at the transition frequencies. 2. The limit decreases in line with the logarithm of the frequency in the range of 0.15 to 0.50MHz. 3. All emanations from a class A/B digital device or system, including any network of conductors and apparatus connected thereto, shall not exceed the level of field strengths specified above. 4.2.2 TEST INSTRUMENTS DESCRIPTION & DATE OF DUE DATE OF MODEL NO. SERIAL NO. MANUFACTURER CALIBRATION CALIBRATION Test Receiver ESCS30 100288 Apr. 24, 2014 Apr. 23, 2015 ROHDE & SCHWARZ RF signal cable 5D-FB Cable-HYCO2-01 Dec. 27, 2013 Dec. 26, 2014 Woken LISN ROHDE & SCHWARZ ESH2-Z5 100100 Dec. 23, 2013 Dec. 22, 2014 (EUT) LISN ROHDE & SCHWARZ ESH3-Z5 100312 Jul. 10, 2014 Jul. 09, 2015 (Peripheral) Software BV ADT_Cond_ NA NA NA ADT V7.3.7.3 NOTE: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in HwaYa Shielded Room 2. 3. The VCCI Site Registration No. is C-2047. Report No.: RF140728C21-1 22 of 28 Report Format Version 5.2.1

4.2.3 TEST PROCEDURES a. The EUT was placed 0.4 meters from the conducting wall of the shielded room with EUT being connected to the power mains through a line impedance stabilization network (LISN). Other support units were connected to the power mains through another LISN. The two LISNs provide 50 ohm/ 50uH of coupling impedance for the measuring instrument. b. Both lines of the power mains connected to the EUT were checked for maximum conducted interference. c. The frequency range from 150kHz to 30MHz was searched. Emission levels under (Limit - 20dB) was not recorded. NOTE: All modes of operation were investigated and the worst-case emissions are reported. 4.2.4 DEVIATION FROM TEST STANDARD No deviation. 4.2.5 TEST SETUP Ve r t ic a l G ro u n d R e f e r e n c e P la n e Te s t R e c e iv e r EUT 40cm 80cm L IS N H o r iz o n ta l G ro u n d R e fe r e n c e P la n e N o t e : 1 .S u p p o r t u n its w e r e c o n n e c te d to s e c o n d L IS N . 2 .B o t h o f L IS N s ( A M N ) a r e 8 0 c m fr o m E U T a n d a t le a s t 8 0 f ro m o th e r u n its a n d o th e r m e ta l p la n e s For the actual test configuration, please refer to the attached file (Test Setup Photo). 4.2.6 EUT OPERATING CONDITIONS Same as 4.1.6. Report No.: RF140728C21-1 23 of 28 Report Format Version 5.2.1

4.2.7 TEST RESULTS CONDUCTED WORST—CASE DATA : 802.11a_1TX PHaSE Line 1 6dB BANDWIDTH |okHz CHANNEL Channel 36 Freq Corr. |Reading Value ETLSVS;" Limit Margin No "Fastor ~Tag (avj] (oB (uv)] [oB (ov)] (aB) hq @s ar av ar ay ar ay ar aAV. 1| ~0.15000_|—0.26 46.08 20.76 46.34 30.02 66.00 56.00 —19.56 25.98 7 o 16953 027| 4025 24.04 4052 24.31 64.98 54.98 —24.46 —20.07 3 040250 030| 36.50 26.24 36.90 26.54 50.55 46.05 _19.74_| 20. 10 2 o.s6563 032| 20282 21.44 30. 14 21.76 56.00 46.00 —25.86 —24.24 5 93516 —o34_| 2027 21.17 290.61 21.51 56.00 246.00 —26.39 —24.49 6 [17.50141 _o56_| 2012 21 12 20.58 21.05 80.00 50.00 3032 2532 REMARKS: 1. Q.P. and AV. are abbreviations of quasi—peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level — Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value. cowe mo— 1eo— so— so— ro— so— so— s— so— z— ols the whe sube mie Report No.: RF140728C21—1 24 of 28 Report Format Version 5.2.1

PHASE Line 2 6dB BANDWIDTH OkHz CHANNEL Channel 36 No Freq. F(;?::gr Reading Value ETLSVS;" Limit Margin [dB (uV)] [dB (uV)] [dB (uV)] (dB) [MHz] (a8) ar av. or av. or av. a.r AV. 1 0.15391 0.27 42.72 26.98 42.99 27.25 66.79 55.79 —22.80 —28.54 2 0.20078 0.28 38.54 26.33 38.82 26.61 63.58 53.58 —24.76 —26.97 3 0.43906 0.30 36.97 30.06 37.27 30.36 57.08 47.08 —19.81 —16.72 4 0.66953 0.32 31.77 22.85 32.09 23.17 56.00 46.00 —23.91 —22.83 5 0.98203 0.34 2957 21.87 29.91 22.21 56.00 46.00 —26.09 —23.79 6 17.32031 0.60 30.08 22.14 30.68 22.74 60.00 50.00 —29.32 —27.26 REMARKS: 1. Q.P. and AV. are abbreviations of quasi—peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level — Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value. cowe mo— 1eo— so— so— ro— so— so— «— so— z— ols 1e tobo sube mie Report No.: RF140728C21—1 25 of 28 Report Format Version 5.2.1

5. PHOTOGRAPHS OF THE TEST CONFIGURATION Please refer to the attached file (Test Setup Photo). Report No.: RF140728C21-1 26 of 28 Report Format Version 5.2.1

6. INFORMATION ON THE TESTING LABORATORIES We, Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, were founded in 1988 to provide our best service in EMC, Radio, Telecom and Safety consultation. Our laboratories are accredited and approved according to ISO/IEC 17025. If you have any comments, please feel free to contact us at the following: Linko EMC/RF Lab: Hsin Chu EMC/RF/Telecom Lab: Tel: 886-2-26052180 Tel: 886-3-5935343 Fax: 886-2-26051924 Fax: 886-3-5935342 Hwa Ya EMC/RF/Safety Lab: Tel: 886-3-3183232 Fax: 886-3-3270892 Email: service.adt@tw.bureauveritas.com Web Site: www.bureauveritas-adt.com The address and road map of all our labs can be found in our web site also. Report No.: RF140728C21-1 27 of 28 Report Format Version 5.2.1

7. APPENDIX A – MODIFICATIONS RECORDERS FOR ENGINEERING CHANGES TO THE EUT BY THE LAB No modifications were made to the EUT by the lab during the test. ---END--- Report No.: RF140728C21-1 28 of 28 Report Format Version 5.2.1


Document Created: 2019-06-13 05:32:58
Document Modified: 2019-06-13 05:32:58
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC