LMA letter

FCC ID: PJMMRU102

Cover Letter(s)

Download: PDF
FCCID_1857288

m. dudde hochfrequenz-technik Rottland 5a, D-51429 Bergisch-Gladbach DIN EN ISO/IEC 17025 certified DAkkS accreditation number: D-PL-12053-01 Tel. : +49 22 07 - 96 89 - 0 Fax : +49 22 07 - 96 89 - 20 email: manfred.dudde@t-online.de www.dudde.com Attn: Reviewing Engineer RE: FCC Part 15C LIMITED MODULAR TRANSMITTER APPROVAL To Whom It May Concern: Our customer, FEIG ELECTRONIC GmbH, hereby requests host specific limited modular approval acc. to FCC Part 15 (Modular Approval) Brand/Trade name: OBID i-scan Model name: ID ISC.MRMU102-E, ID ISC.MRU102-PoE, ID ISC.MRU102-USB FCC certification number: PJMMRU102 Transmitters designed as modules for the installation in a host device may obtain equipment certification as a modular device provided that the applicable FCC part is met and the following conditions in this section are met. Items to be covered Answer from applicant 1. The modular transmitter must have its own RF shielding. No, see internal photographs "Annex No. 2" 2. The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements YES under conditions of excessive data rates or over-modulation. 3. The modular transmitter must have its own power supply regulation. YES 4. The modular transmitter must comply with the antenna requirements of Section NO, the RF module will be 15.203 and 15.204(c). The antenna must either be permanently attached or employ integrated into host devices a “unique” antenna coupler (at all connections between the module and the antenna, subject to professional including the cable). installation SMA antenna connector 5. The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing. This is intended to No, see test setup photographs demonstrate that the module is capable of complying with Part 15 emission limits "Annex No. 6" regardless of the device into which it is eventually installed.

m. dudde hochfrequenz-technik Rottland 5a, D-51429 Bergisch-Gladbach DIN EN ISO/IEC 17025 certified DAkkS accreditation number: D-PL-12053-01 Tel. : +49 22 07 - 96 89 - 0 Fax : +49 22 07 - 96 89 - 20 email: manfred.dudde@t-online.de www.dudde.com 6. The modular transmitter must be labeled with its own FCC ID number, and, if the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: XYZMODEL1” or “Contains FCC ID: XYZMODEL1.” Any similar wording that expresses the same meaning YES, see label sample "Annex may be used. The Grantee may either provide such a label, an example of which No. 4” must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. 7. The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. For example, there are very strict operational and timing requirements that must be met before a transmitter is authorized for operation YES under Section 15.231. For instance, data transmission is prohibited, except for operation under Section 15.231(e), in which case there are separate field strength level and timing requirements. Compliance with these requirements must be assured. 8. The modular transmitter must comply with any applicable RF exposure requirements. For example, FCC Rules in Sections 2.1091, 2.1093 and specific Sections of Part 15, including 15.319(i), 15.407(f), 15.253(f) and 15.255(g), require that Unlicensed PCS, UNII and millimeter wave devices perform routine environmental evaluation for RF Exposure to demonstrate compliance. In addition, spread spectrum transmitters operating under Section 15.247 are required to YES, for fixed and mobile host address RF Exposure compliance in accordance with Section 15.247(b)(4). configuration Modular transmitters approved under other Sections of Part 15, when necessary, may also need to address certain RF Exposure concerns, typically by providing specific installation and operating instructions for users, installers and other interested parties to ensure compliance. Note: If compliance with one or more of the numbered requirements, listed above, cannot be demonstrated, it may be possible to obtain a “Limited Modular Approval” (LMA). m. dudde hochfrequenz-technik Andreas Morsbach Management Assistant


Document Created: 2012-12-05 09:49:37
Document Modified: 2012-12-05 09:49:37
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC