UM

FCC ID: PJMLRU3000

Users Manual

Download: PDF
FCCID_2177331

Annex no. 5 Functional Description / User Manual Date: 2012-06-11 Vers. no. 1.12 m. dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

INSTALLATION ID ISC.LRU3000 / ID ISC.LRU3500 UHF Long Range Reader final – public (B) 2013-10-28 – M21016-3e-ID-B

OBID i-scan ® UHF Installation ID ISC.LRU3000/3500 Note  Copyright 2013 by FEIG ELECTRONIC GmbH Lange Strasse 4 D-35781 Weilburg Tel.: +49 6471 3109-0 http://www.feig.de With the edition of this document, all previous editions become void. Indications made in this manual may be changed without previous notice. Copying of this document, and giving it to others and the use or communication of the contents thereof are forbidden without express authority. Offenders are liable to the payment of damages. All rights are reserved in the event of the grant of a patent or the registration of a utility model or design. Composition of the information in this document has been done to the best of our knowledge. FEIG ELECTRONIC GmbH does not guarantee the correctness and completeness of the details given in this manual and may not be held liable for damages ensuing from incorrect or incomplete information. Since, despite all our efforts, errors may not be completely avoided, we are always grateful for your useful tips. The instructions given in this manual are based on advantageous boundary conditions. FEIG ELECTRONIC GmbH does not give any guarantee promise for perfect function in cross environments and does not give any guaranty for the functionality of the complete system which incorporates the subject of this document. FEIG ELECTRONIC call explicit attention that devices which are subject of this document are not designed with components and testing methods for a level of reliability suitable for use in or in connection with surgical implants or as critical components in any life support systems whose failure to perform can reasonably be expected to cause significant injury to a human. To avoid damage, injury, or death, the user or application designer must take reasonably prudent steps to protect against system failures. Use Exclusion in Transportation Market: Devices which are subject of this document may NOT be sold, used, leased, offer for sale, or otherwise transferred, exported, and imported by anyone in the Transportation Market. “Transportation Market” means (i) Electronic Toll and Traffic Management (ETTM), (ii) Public Sector Vehicle Registration, Inspection and Licensing Programs, (iii) Railroad Locomotive and Wagon tracking, (iv) airport based ground transportation management systems (GTMS) and taxi dispatch, (v) revenue based parking, and (vi) vehicle initiated mobile payment applications, where the RFID sticker/tag is initially attached to the vehicle but not incorporated at the point of vehicle manufacture. FEIG ELECTRONIC GmbH assumes no responsibility for the use of any information contained in this docu- ment and makes no representation that they free of patent infringement. FEIG ELECTRONIC GmbH does not convey any license under its patent rights nor the rights of others. ® ® OBID and OBID i-scan are registered trademarks of FEIG ELECTRONIC GmbH. FEIG ELECTRONIC GmbH Page 2 of 32 M21016-3e-ID-B

OBID i-scan ® UHF Installation ID ISC.LRU3000/3500 General information's regarding this document • The sign "" indicates extensions or changes of this manual compared with the former issue. • If bits within one byte are filled with "-", these bit spaces are reserved for future extensions or for internal testing- and manufacturing-functions. These bit spaces must not be changed, as this may cause faulty operation of the reader. • The following figure formats are used: 0...9: for decimal figures 0x00...0xFF: for hexadecimal figures, b0...1 for binary figures. • The hexadecimal value in brackets "[ ]" marks a control byte (command). FEIG ELECTRONIC GmbH Page 3 of 32 M21016-3e-ID-B

OBID i-scan ® UHF Installation ID ISC.LRU3000/3500 Contents 1. Safety Instructions / Warning - Read before start-up ! 6 2. Performance Features of Reader Family ID ISC.LRU3000 7 2.1. Performance features ........................................................................................................ 7 2.2. Available Reader types ..................................................................................................... 7 2.3. Available Accessories ....................................................................................................... 7 3. Installation 8 4. Terminals 9 4.1. Antenna Connection ....................................................................................................... 10 4.2. Power Supply................................................................................................................... 11 4.2.1. Power Supply via connection X1 ................................................................................ 11 4.2.2. Power Supply via Power over Ethernet (PoE) ............................................................ 12 4.3. Interfaces ......................................................................................................................... 13 4.3.1. Ethernet Interface on connector X2 ............................................................................ 13 4.3.2. USB Interface on connector X3 .................................................................................. 13 4.3.3. USB Interface on connector X4 (WLAN) .................................................................... 13 4.3.4. RS232 Interface on connector X6 .............................................................................. 14 4.3.5. RS485 Interface on connector X6 .............................................................................. 15 4.3.5.1. Address assignment of RS485 for bus operation ........................................... 16 4.3.6. Data-Clock Interface on connector X5 ........................................................................ 16 4.4. Digital Inputs on connector X5 ....................................................................................... 18 4.5. Outputs on connector X5 ................................................................................................ 19 4.5.1. Digital outputs on connector X5 ................................................................................. 19 4.5.2. Relay outputs on connector X5 .................................................................................. 20 5. Operating and Display Elements 22 5.1. Status LEDs ..................................................................................................................... 22 FEIG ELECTRONIC GmbH Page 4 of 32 M21016-3e-ID-B

OBID i-scan ® UHF Installation ID ISC.LRU3000/3500 5.2. Reset Push Buttons ........................................................................................................ 23 5.3. Reader Power adjustment............................................................................................... 24 5.3.1. EU-Reader according to EN302 208 .......................................................................... 24 5.3.2. FCC-Reader according to FCC 47 Part 15 ................................................................. 25 6. Technical Data 26 7. Radio Approvals 29 7.1. Europe (CE)...................................................................................................................... 29 7.2. Declaration of Conformity (Directive 1999/5/EC - R&TTE) ............................................ 30 7.3. USA (FCC) and Canada (IC) ............................................................................................ 31 7.3.1. USA (FCC) and Canada (IC) warning notices ............................................................ 31 7.3.2. Label Information ....................................................................................................... 32 7.3.3. Installation with FCC / IC Approval ............................................................................. 32 7.3.4. USA (FCC) and Canada (IC) approved antennas ...................................................... 32 FEIG ELECTRONIC GmbH Page 5 of 32 M21016-3e-ID-B

OBID i-scan ® UHF Installation ID ISC.LRU3000/3500 1. Safety Instructions / Warning - Read before start-up ! • The device may only be used for the intended purpose designed by for the manufacturer. • The operation manual should be conveniently kept available at all times for each user. • Unauthorized changes and the use of spare parts and additional devices which have not been sold or recommended by the manufacturer may cause fire, electric shocks or injuries. Such unauthorized measures shall exclude any liability by the manufacturer. • The liability-prescriptions of the manufacturer in the issue valid at the time of purchase are valid for the device. The manufacturer shall not be held legally responsible for inaccuracies, errors, or omissions in the manual or automatically set parameters for a device or for an incorrect application of a device. • Repairs may only be executed by the manufacturer. • Installation, operation, and maintenance procedures should only be carried out by qualified personnel. • Use of the device and its installation must be in accordance with national legal requirements and local electrical codes . • When working on devices the valid safety regulations must be observed. • When installing the device in areas covered under FCC 47 CFR Part 15 a minimum separation of 23 cm (9 inch) between antenna and the human body must be maintained. • Special advice for carriers of cardiac pacemakers: Although this device doesn't exceed the valid limits for electromagnetic fields you should keep a minimum distance of 25 cm between the device and your cardiac pacemaker and not stay in an immediate proximity of the device respective the antenna for some time. FEIG ELECTRONIC GmbH Page 6 of 32 M21016-3e-ID-B

OBID i-scan ® UHF Installation ID ISC.LRU3000/3500 2. Performance Features of Reader Family ID ISC.LRU3000 2.1. Performance features The Reader has been developed for reading passive data carriers, so-called „Smart Labels“, using an operating frequency in the UHF range. 2.2. Available Reader types The following Readers are available: Table 1: Available Reader Types Reader type Description ID ISC.LRU3500-EU Device version for Europe with PoE (max. 4Watt) ID ISC.LRU3000-EU Device version for Europe without PoE (max. 2Watt) ID ISC.LRU3500-FCC Device version for USA with PoE (max. 4Watt) ID ISC.LRU3000-FCC Device version for USA without PoE (max. 2Watt) 2.3. Available Accessories The following optional accessories are currently available: Table 2: Optional Reader Accessories Reader type Description Protection cap for IP 64 Art.No.: 3558.000.00 ID ISC.LR.CSC-IP64 Connector Sealing Cap ID ISC.LRU3x00-MS Mounting Rail Mounting Set for ID ISC.LRU3000/3500 Rail Set Art.No.: 3831.000.00 FEIG ELECTRONIC GmbH Page 7 of 32 M21016-3e-ID-B

OBID i-scan ® UHF Installation ID ISC.LRU3000/3500 3. Installation The Reader is designed for wall-mount, including outdoors. Holes for mounting on a wall are provided in the housing. It is not necessary to open the reader housing mounting. 261,3 (10.29) 68 (2.68) 157,3 (6.19) 34 (1.34) 25,5 (1.00) 241,7 (9.52) Figure 1: Installation Drawing FEIG ELECTRONIC GmbH Page 8 of 32 M21016-3e-ID-B

OBID i-scan ® UHF Installation ID ISC.LRU3000/3500 4. Terminals On the lower side of the reader housing the different cable connectors are positioned. Figure 2: Connection Overview shows the arrangement of the connectors and Table 3: Connection terminals shows which connection for the different cables are used for. Table 4: Push button function shows the available push buttons. X1 ANT1 ANT2 ANT3 ANT4 X2 X5 X3 X4 X6 T1 T2 Figure 2: Connection Overview Table 3: Connection terminals Connector Description ANT 1-4 Connection of the external antennas (Impedance 50Ω) X1 Power supply 24VDC +-5% X2 10/100Tbase network connection with RJ-45 (with PoE) X3 USB interface for host communication X4 USB interface for WLAN-Sticks X5 Digital input and output and relay output X6 RS232 / 485 interface Table 4: Push button function Push button Description T1 Internal push button for complete configuration reset T2 External push button for CPU-Reset FEIG ELECTRONIC GmbH Page 9 of 32 M21016-3e-ID-B

OBID i-scan ® UHF Installation ID ISC.LRU3000/3500 4.1. Antenna Connection The external SMA antenna connectors are positioned on the lower side of the reader. The maximum tightening torque for the SMA sockets is 0.45 Nm (4.0 lbf in). CAUTION: Exceeding the tightening torque will destroy the plug. Table 5: External antenna connection Terminal Description ANT 1 - 4 Connection for external antennas (input impedance 50Ω) Figure 3: External antenna connection ANT1-4 and X1 for the power supply CAUTION: A direct connection of an antenna to an antenna output with activated DC Voltage (24 VDC, 500 mA) may damage the antenna. FEIG ELECTRONIC GmbH Page 10 of 32 M21016-3e-ID-B

OBID i-scan ® UHF Installation ID ISC.LRU3000/3500 4.2. Power Supply 4.2.1. Power Supply via connection X1 The supply voltage of 24 V DC has to be connected to Terminal X1. Table 6: Pin assignment for power supply Terminal Abbreviation Description X1 / Pin 1 VDC Vcc – supply voltage 24VDC +-5% X1 / Pin 2 GND Ground – supply voltage Figure 4: Connection for the power supply CAUTION: The reader has to be supplied by a limited power supply (e.g. NEC Class 2/LPS power sup- ply) according IEC EN 60950-1 chapter 2.5, only. Reversing the polarity of the supply voltage may destroy the device. Each reader has to be supplied by a separate external power supply. An operation of an ID ISC.LRU3500 via an external power supply and Power over Ethernet (PoE) at the same time is not recommended and can cause interferences during operation. FEIG ELECTRONIC GmbH Page 11 of 32 M21016-3e-ID-B

OBID i-scan ® UHF Installation ID ISC.LRU3000/3500 4.2.2. Power Supply via Power over Ethernet (PoE) Optional the reader (only LRU3500) can be powered via the LAN connector on X2 with the use of a PoE „Power over Ethernet“ power supply according to IEEE802.3at*, Class4 (30/25,5Watt). The DC supply can be achieved via the free pin’s 4,5 and 7,8 (Midspan-Power). Also a “Phantom Pow- ering” (Inline-Power) via the signal pin’s 1,2,3,and 6 is possible. Depending on the cable cross- section the following cable distances can be used. Table 7: Maximum cable length if PoE is used cable cross-section (CAT5...7) Maximum cable length for PoE 0,4mm ≈ 30m 0,6mm ≈ 70m * For detailed technical information regarding the 802.3at standard, please refer to the most recent edition of the corresponding IEEE specification. Figure 5: LAN and PoE connection CAUTION: Take care if PoE is used the maximum reader output power of the reader must be limited to 1Watt. It must be ensured that the reader is supplied with 42,5 V DC (48 V DC – cable losses) at least. This functionality is only available with the reader models ID ISC.LRU3500-EU and ID ISC.LRU3500-FCC. An operation of an ID ISC.LRU3500 via an external power supply and Power over Ethernet (PoE) at the same time is not recommended and can cause interferences during operation. If Power over Ethernet is used WLAN is not available. FEIG ELECTRONIC GmbH Page 12 of 32 M21016-3e-ID-B

OBID i-scan ® UHF Installation ID ISC.LRU3000/3500 4.3. Interfaces 4.3.1. Ethernet Interface on connector X2 The Reader has an integrated 10 / 100 base-T network port for an RJ-45. Connection is made on X2 and has an automatic “Crossover Detection” according to the 100BASE-T Standard. With structured cabling CAT 5 cables should be used. This ensures a reliable operation at 10 Mbps or 100 Mbps. The prerequisite for using TCP/IP protocol is that each device has a unique address on the net- work. All Readers have a factory set IP address. Table 8: Standard factory configuration of the Ethernet connection Network Address IP-Adresse 192.168.10.10 Subnet-Mask 255.255.255.0 Port 10001 DHCP OFF NOTE: The reader is equipped with a DHCP ready Ethernet Interface. 4.3.2. USB Interface on connector X3 The USB socket on the board is terminal X3. The pinout is standardized. The data rate is reduced to 12 Mbit (USB full speed). A standard USB-cable can be used. Figure 6: USB-Interface for host communication NOTE: The length of the USB-cable can have a max. of 5m (20 inch). It is not allowed to use longer cables. 4.3.3. USB Interface on connector X4 (WLAN) FEIG ELECTRONIC GmbH Page 13 of 32 M21016-3e-ID-B

OBID i-scan ® UHF Installation ID ISC.LRU3000/3500 The USB-Port X4 can be used for a standard WLAN-USB-Stick Figure 7: USB-Interface for external WLAN stick NOTE: WLAN shall not be used when the reader is powered via Power over Ethernet (PoE) The following table gives an overview about successfully tested Wireless LAN Sticks Table 9: Successfully tested WLAN Sticks Manufacturer Description Model Buffalo Wireless-N NFiniti High Power WLI-UC-G300HP Buffalo Wireless –N NFiniti WLI-UC-G300N Cisco / Linksys Wireless Network USB Adapter WUSB100 Netgear Wireless-G 54 USB Adapter WG111 v3 4.3.4. RS232 Interface on connector X6 The RS232 interface is connected on X6. The transmission parameters can be configured by means of software protocol. Figure 8: RS232 interface pin-outs on X6 FEIG ELECTRONIC GmbH Page 14 of 32 M21016-3e-ID-B

OBID i-scan ® UHF Installation ID ISC.LRU3000/3500 Figure 9: Wiring example for connecting the RS232 interface RS485-Schnittstelle X6 4.3.5. RS485 Interface on connector X6 The connection of the RS485 interface take place via the X6 connector as well. The interface pa- rameter can be configured via software protocols. Figure 10: RS485 interface pin-outs on X6 (RS485-Interface): Table 10: RS485 interface pin-outs Abbreviation Description GND RS485 – GND A- RS485 – (A -) B+ RS485 – (B +) FEIG ELECTRONIC GmbH Page 15 of 32 M21016-3e-ID-B

OBID i-scan ® UHF Installation ID ISC.LRU3000/3500 4.3.5.1. Address assignment of RS485 for bus operation For bus operation the Reader can be assigned the required bus address via software. The address is assigned by the host computer. The software is used to assign addresses “0” through “254” to the Reader. A potential termination of the interface bus can be configured by the software as well. NOTE: Since all Readers are factory set with address „0“, they must be connected and configured one after the other. 4.3.6. Data-Clock Interface on connector X5 The connection of the data-clock interface take place via the digital Outputs OUT1 and OUT2 at connector X5. The wire for the clock needs to be connected to connector OUT1-C, the wire for the data needs to be connected to connector OUT2-C. Clock / Data-0 Figure 11: Data-Clock Interface on connector X5 NOTE: FEIG ELECTRONIC GmbH Page 16 of 32 M21016-3e-ID-B

OBID i-scan ® UHF Installation ID ISC.LRU3000/3500 The data-clock interface is only available in Scan-Mode. The data-clock interface cannot be used to configure the reader. The digital outputs OUT1 and OUT2 are not available, if the data-clock interface is activated. The data as well as the clock need to be supplied with an external voltage. The output is configured for max. 24 V DC / 30 mA. Figure 12: Wiring Example NOTE: Please consider possible limitations of the Wiegand Controller regarding the used supply voltage. In dependency on the inner circuit of the used Wiegand Controller it is necessary to use external serial resistors to limit the current on the data and clock wires. The necessity of the external pull down resistor is depending on the inner circuit of the used Wiegand Controller FEIG ELECTRONIC GmbH Page 17 of 32 M21016-3e-ID-B

OBID i-scan ® UHF Installation ID ISC.LRU3000/3500 4.4. Digital Inputs on connector X5 The optocouplers on Terminal X5 are galvanically isolated from the Reader electronics and must therefore be externally supplied. Figure 13: Optocoupler pin-outs IN1 – IN5 Figure 14: Internal and possible external wiring of the optocoupler inputs Optocoupler input (X5/1-5): The input LED associated with the optocoupler is connected internally to a series resistor of 500 Ω. For supply voltages of greater than 10V the input current must be limited to max. 20 mA by means of an additional series resistor (see Fehler! Verweisquelle konnte nicht gefunden werden.). Table 11 shows the necessary external resistors for various external voltages Uext. FEIG ELECTRONIC GmbH Page 18 of 32 M21016-3e-ID-B

OBID i-scan ® UHF Installation ID ISC.LRU3000/3500 Table 11: Required external series resistor Rext External voltage Uext Required external series resistor Rext 5 V ... 10 V --- 11 V ... 15 V 270 Ω 16 V ... 20 V 560 Ω 21 V ... 24 V 820 Ω NOTE: The input is configured for a maximum input voltage of 5-10 V DC and an input current of max. 20 mA. Polarity reversal or overload on the input will destroy it. 4.5. Outputs on connector X5 4.5.1. Digital outputs on connector X5 Optocoupler output (X5/1-2): The transistor connections, collector and emitter, of the optocoupler output are galvanically isolated from the Reader electronics and are carried to the outside without any internal ancillary circuitry on Terminal X5. The output must therefore be powered by an external power supply. Figure 15: Optocoupler -Outputs OUT1-2 FEIG ELECTRONIC GmbH Page 19 of 32 M21016-3e-ID-B

OBID i-scan ® UHF Installation ID ISC.LRU3000/3500 Figure 16: Internal and possible external wiring of the optocoupler-outputs OUT1-2 CAUTION: The output is configured for max. 24 V DC / 30 mA. Polarity reversal or overload on the output will destroy it. The output is intended for switching resistive loads only. 4.5.2. Relay outputs on connector X5 There are 3 relay outputs available on connector X5. Figure 17: Relay output pin-outs REL1-3 FEIG ELECTRONIC GmbH Page 20 of 32 M21016-3e-ID-B

OBID i-scan ® UHF Installation ID ISC.LRU3000/3500 CAUTION: The relay output is configured for max. 24 V DC / 2 A constant load. The switching current must not exceed 1A. The relay output is intended for switching resistive loads only. If an inductive load is con- nected, the relay contacts must be protected by means of an external protection circuit. Figure 18: Internal and possible external wiring of the relay output FEIG ELECTRONIC GmbH Page 21 of 32 M21016-3e-ID-B

OBID i-scan ® UHF Installation ID ISC.LRU3000/3500 5. Operating and Display Elements 5.1. Status LEDs Table 12: Configuration of the LEDs Host Warning Communication ANT 1- 4 Input RUN Output Green Yellow Red Description ON OFF ON Boot sequence (ca.10s) after power on FLASH OFF OFF Normal Reader operation (without Host communication) FLASH BLINKT OFF Reader receives a valid protocol from host FLASH OFF ON RF Warning [0x84] (without host communication) FLASH FLASH Firmware Activation necessary [0x17] / (alternat- OFF (alternat- ing) ing) Wrong Firmware [0x18] FLASH FLASH (synchro- OFF (synchro- RFC Hardware Error [0xF1] nous) nous) FLASH FLASH Hardware Warning OFF (synchro- (synchro- nous) nous) (ACC EEPROM Error / RFC not detected) FLASH OFF FLASH USB Host Error (fast) Firmware Update: FLASH FLASH FLASH Firmware transfer from host to reader (Please do not switch off the reader or disconnect the interface cable) (light in sequence) FLASH FLASH FLASH Firmware flash into EEPROM. (Please do not switch off the reader or disconnect the interface cable) synchronous FEIG ELECTRONIC GmbH Page 22 of 32 M21016-3e-ID-B

OBID i-scan ® UHF Installation ID ISC.LRU3000/3500 Green Yellow Red Description Configurations-Reset: FLASH FLASH FLASH While T1 is pushed and hold for maximal 5s (light in sequence) After T1 has been pushed and hold for 5s. Configuration ON ON ON Reset has been finished. Input / Output LED (yellow): Configurable LED. Can display the status of a digital input or output ANT 1 – 4: Green HF Power switched on Blue Tag-Detect Red Antenna impedance error (> 50Ohm or <50Ohm) 5.2. Reset Push Buttons Figure 19 shows the position of the reset push button’s T1 and T2. At the right side of the connector X6 the push button T2 is positioned. With this push button a CPU- Reset can be performed. With the push button T1 within the reader housing on left side of X3 a complete con- figuration reset can be performed. For performing a reset you should use a pa- per clip and push the button T1 for at least 5 s until the 3 status LED’s (left side) are switched on continuously, see 5.1. Status LEDs Table 12: Configuration of the LEDs . Table 12: Configuration of the LEDs Figure 19: Position of the reset-switches T1 and T2 FEIG ELECTRONIC GmbH Page 23 of 32 M21016-3e-ID-B

OBID i-scan ® UHF Installation ID ISC.LRU3000/3500 5.3. Reader Power adjustment To achieve the optimum reading performance it is necessary to set the reader output power to the highest allowed value. This depends on the used reader type (EU / FCC) and the regulation in the country were the reader is used. 5.3.1. EU-Reader according to EN302 208 According to the standard EN302 208 the maximum radiated power is 2 W e.r.p. (Effective Radiat- ed Power) in countries of the European Union. The in the reader configured output power Pout de- pends on the antenna gain in dBi and the attenuation of the antenna cable. If a circular polarized antenna is used the antenna gain [dBic] can be reduced by 3dB. At a linear polarized antenna the maximum linear antenna gain [dBi] must be used. POut = Perp - Antenna Gain + Cable loss + 2,1dB** ** Correction Factor to convert the radiated power from e.r.p to e.i.r.p. For the calculation of the reader output power POut an Excel file „Calc-RF-Power.xls“ can be used. Available from Feig Electronic GmbH. Example: ** linear antenna = „0“, circular antenna = „1“ Figure 20: Calculation of the output power In Figure 20 the allowed antenna power is shown for the use of the FEIG standard antenna ANT.U600/270 –EU and a 6m long Belden H155 coaxial cable. FEIG ELECTRONIC GmbH Page 24 of 32 M21016-3e-ID-B

OBID i-scan ® UHF Installation ID ISC.LRU3000/3500 5.3.2. FCC-Reader according to FCC 47 Part 15 According to the FCC approval, Title 47, Part15 the maximum output power of the reader is limited to 1 W (30dBm). The maximum radiated power of the antenna should not increase more then 4 W e.i.r.p. Due to these facts two different cases have to be considered: If a linear polarized antenna is used which gain is less then 6 dBi (factor 4), or if a circular polarized antenna is used which gain is less then 9dBic the reader can always be configured to an output power of 1W. Antenna Gain < 6dBi → Pout = 1 W This would be the case if the FEIG standard antennas ANT.U170/170 -FCC (4dBic) or ANT.U270/270 -FCC (8,7dBic) are used. If an antenna is used which gain is more then 6dBi (9dBic) it is necessary to consider the antenna gain and the attenuation of the antenna cable to calculate the right output power. If a circular polar- ized antenna is used the antenna gain [G]=dBic can be reduced by 3dB. This is the case if the FEIG standard antenna ANT.U600/270 -FCC is used. In this configuration the maximum output power of the reader can be calculated in the following way. POut = 36 dBm (4 W e.i.r.p) – Antenna Gain (in dBi) + Cable Loss (in dB) POut = 36 dBm (4 W e.i.r.p) – Antenna Gain (in dBic) – 3 dB + Cable Loss (in dB) The antenna gain of the circular polarized standard antenna ANT.U600/270 is 10,5 dBic. This could be compared with a gain of 7,5 dBi of a linear polarized antenna (10,5 dBic – 3 dB). Example 1: Antenna ANT.U600/270 and 2 m Belden H155 Coaxial Cable: Pout= 36 dBm – 10,5 dBic + 3 dB + 0,6 dB Pout= 36 dBm – 7,5 dBi + 0,6 dB Pout= 29,1 dBm Reader Configuration = 0,8 Watt Example 2: Antenna ANT.U600/270 and 6m Belden H155 Coaxial Cable: Pout= 36 dBm – 10,5 dBic + 3 dB + 1,8 dB Pout= 36 dBm – 7,5 dBi + 1,8 dB Pout= 30,3 dBm Reader Configuration = 1,0 Watt According to Example 2 it will only be necessary to adapt the output power of the reader when the antenna ANT.U600/270 is used if the length of the antenna cable is less then 6m. FEIG ELECTRONIC GmbH Page 25 of 32 M21016-3e-ID-B

OBID i-scan ® UHF Installation ID ISC.LRU3000/3500 6. Technical Data MECHANICAL DATA Housing Aluminum powder-coated Dimension (W x H x D) 261,3 mm x 157,3 mm x 68 mm) 10.29 inch x 6.19 inch x 2.68 inch Weight 2,0 kg (4.4 lb) Protection Class IP 53 (with protection cap IP64) Colour RAL 9003 (Signal White) ELECTRICAL DATA Power Supply • ID ISC.LRU3000 24 V DC ± 5 % (Noise Ripple: max. 150 mV) • ID ISC.LRU3500 24 V DC ± 5 % (Noise Ripple: max. 150 mV) or Power over Ethernet (min. 42,5 V DC) Power Consumption max. 35 W Operating Frequency • EU-Reader 865 MHz to 868 MHz (EN 302208) • FCC-Reader 902 MHz to 928 MHz (FCC47 Part15) RF-Power • ID ISC.LRU3000 300 mW to max. 2 W configurable • ID ISC.LRU3500 300 mW to max. 4 W configurable max. 1 W if powered via Power over Ethernet Antenna Connection • ID ISC.LRU3000 4 x SMA female (50 Ω), internal Multiplexer • ID ISC.LRU3500 4 x SMA female (50 Ω), internal Multiplexer, optional a DC voltage of 24 V DC / 500 mA can be activated at the antenna output Outputs • 2 x Optocoupler 24 V DC / 30 mA (galvanically isolated) • 3 x Relay (1 x normal open) 24 V DC / 1 A (switching current), (2A con- stant load) FEIG ELECTRONIC GmbH Page 26 of 32 M21016-3e-ID-B

OBID i-scan ® UHF Installation ID ISC.LRU3000/3500 Inputs • 5 x Optocoupler max. 5-10 V DC / 20 mA Interfaces RS232, RS485, USB (full Speed), Ethernet, USB Host, Data-Clock FUNCTIONAL PROPERTIES Protocol Modes FEIG ISO HOST Mode (Advanced Protocol Frame) Buffered Read Mode Automatic Data Scan Mode Buffering and Notification Mode Filtering Supported Transponder Types EPC Class 1 Generation 2 ISO 18000-6-C (Upgrade Code required) further transponder types possible on demand Optical Indicators 8 LEDs for operating status and diagnostics Operating System Linux (64 MB RAM, 256 MB Flash) Further Features Anticollision RSSI Real Time Clock RF-Channel monitoring Antenna SWR monitoring Temperature Monitoring* AMBIENT CONDITIONS Temperature Range • Operation -25 °C to +55 °C -25 °C to +50 °C (only LRU3500 with PoE) • Storage -25 °C to +85 °C Humidity 5 % to 95 % non-condensing * Caution: Overheating of the device may result in performance losses. It is recommended to activate the RF of the reader only if there is a transponder in the detection range of an antenna. FEIG ELECTRONIC GmbH Page 27 of 32 M21016-3e-ID-B

OBID i-scan ® UHF Installation ID ISC.LRU3000/3500 Vibration EN 60068-2-6 10 Hz to 150 Hz: 0,075 mm / 1 g Shock EN 60068-2-27 Acceleration 30 g APPLICABLE STANDARDS Radio Regulation • Europe EN 302 208 • USA FCC 47 CFR Part 15 • Canada IC RSS-Gen, RSS-210 EMC EN 301 489 Safety • Low Voltage EN 60950 • Human Exposure EN 50364 FEIG ELECTRONIC GmbH Page 28 of 32 M21016-3e-ID-B

OBID i-scan ® UHF Installation ID ISC.LRU3000/3500 7. Radio Approvals 7.1. Europe (CE) When properly used this radio equipment conforms to the essential requirements of Article 3 and the other relevant provisions of the R&TTE Directive 1999/5/EC of March 99. Performance Classification according to ETSI EN 301 489: Class 2 FEIG ELECTRONIC GmbH Page 29 of 32 M21016-3e-ID-B

OBID i-scan ® UHF Installation ID ISC.LRU3000/3500 7.2. Declaration of Conformity (Directive 1999/5/EC - R&TTE) Figure 21: Declaration of Conformity FEIG ELECTRONIC GmbH Page 30 of 32 M21016-3e-ID-B

OBID i-scan ® UHF Installation ID ISC.LRU3000/3500 7.3. USA (FCC) and Canada (IC) 7.3.1. USA (FCC) and Canada (IC) warning notices Product name: ID ISC.LRU3000-FCC ID ISC.LRU3500-FCC Reader name: ID ISC.LRU3000-FCC ID ISC.LRU3500-FCC FCC ID: PJMLRU3000 IC: 6633A-LRU3000 Notice for USA and This device complies with Part 15 of the FCC Rules and with Canada RSS-210 of Industry Canada. Operation is subject to the following two conditions. (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Unauthorized modifications may void the authority granted under Federal communications Commission Rules permitting the operation of this device. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Le présent appareil est conforme aux CNR d'Industrie Canada appli- cables aux appareils radio exempts de licence. L'exploitation est auto- risée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonc- tionnement. Warning: Changes or modification made to this equipment not expressly approved by FEIG ELECTRONIC GmbH may void the FCC authorization to operate this equipment. FEIG ELECTRONIC GmbH Page 31 of 32 M21016-3e-ID-B

OBID i-scan ® UHF Installation ID ISC.LRU3000/3500 7.3.2. Label Information The following information must be placed at the outer side of the housing in which the reader is mounted. Contains FCC ID PJMLRU3000 Contains IC: 6633A-LRU3000 7.3.3. Installation with FCC / IC Approval FCC-/IC-NOTICE: To comply with FCC Part 15 Rules in the United States / with IC Radio Stand- ards in Canada, the system must be professionally installed to ensure compliance with the Part 15 certification / IC certification. It is the responsibility of the operator and professional installer to en- sure that only certified systems are deployed in the United States / Canada. 7.3.4. USA (FCC) and Canada (IC) approved antennas This radio transmitter (identify the device by certification number, or model number if Category II) has been approved by Industry Canada to operate with the antenna types listed below with maxi- mum permission gain and required antenna impedance for each antenna type indicated. Antenna types, not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device Le présent émetteur radio (identifier le dispositif par son numéro de certification ou son numéro de modèle s’il fait partie du matériel de catégorie I) a été approuvé par Industrie Canada pour fonc- tionner avec les types d’antenne ’énoncé ci-dessus et ayant un gain admissible maximal et l’impédance requise pour chaque type d’antenne. Les types d’antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l’exploitation de l’émetteur Following antennas are approved by FCC according FCC Part 15 and IC Canada according RS210 • ID ISC.ANT.U170/170-FCC (4.0 dBic) • ID ISC.ANT.U270/270-FCC (9.0 dBic) • ID ISC.ANT.U600/270-FCC (10,5 dBic) FEIG ELECTRONIC GmbH Page 32 of 32 M21016-3e-ID-B


Document Created: 2013-10-29 11:50:57
Document Modified: 2013-10-29 11:50:57
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC